Underwater Housing for Olympus E-PL2 User Manual
Contents
1. Flash On e Turn button counter clockwise to turn on the flash eMake sure that the Flash is turned off with Flash Off Lever 1 before taking the camera out from the housing Movie Press to start or stop recording video Close up Playback Press to zoom in on frame Info Press to activate the Info button Index Calendar Display Press to activate Index Calendar Display Exposure Compensation Press to activate exposure compensation Single Frame Playback Press to display most recent photograph or video AF Target Press to activate the AF Target button OK Press to activate the OK button Delete Press to delete an image Menu Press to display the menus Sequential Shooting Self Timer Press to activate Flash Control Dial Press to display flash options Press and turn to rotate the Control Dial Housing Lid Clear acrylic back cover of the housing 21 Zoom Control Press and turn to adjust the zoom 22 Zoom Control Press and turn to adjust the zoom 23 Focus Control Press and turn to adjust the focus 24 Lens Release For use with LUMIX DMYV MA1 four third lens mount adaptor For details of camera functions and settings accessed by each control button please consult the Olympus E PL2 camera instruction manual 4 Set up Instructions Special Note on Responsibility for Watertight Integrity Each housing is individually inspected and hydrostatically tested in the factory However the res2. Silicone O ring Grease Included Carrying Bag Included Red Magenta Filter Optional i Port for 14mm or 20mm Optional Port for 7 14mm 9 18mm 14 42mm 14 42mm II 14 45mm Optional 45mm Macro Conversion Lens Optional 8mm Wide Angle Conversion Lens Optional 3 Function Controls Function Control Buttons 1 Flash Off 2 Bulkhead 3 Mode Dial 4 Power On 1 Off 5 Shutter 6 Key Hole Lock 7 Flash On 8 Movie 9 Close up Playback 10 Info 11 Index Calendar Display ly 12 Exposure Compensation 13 Single Frame Playback 14 AF Target 15 OK 16 Erase 17 Menu 18 Sequential Shooting Self Timer 19 Flash Control Dial 20 Housing Lid 21 Zoom Control 22 Zoom Control 23 Focus Control 24 Lens Release Control Buttons Details 1 10 1 pd 12 13 14 15 16 17 18 19 20 Flash Off ePress the lever down to turn off the flash eMake sure that the Flash is turned off before removing the camera from the housing Bulkhead e For connecting the sync cord e Unscrew the rubber protective plug and install the sync cord e Always keep the rubber protective plug in place if sync cord is not installed Mode Dial Turn to select the shooting mode Power On Off Press to power on and off Shutter Press down to activate the shutter Key Hole Lock Press down and turn to lock and unlock the lid
3. Underwater Housing for Olympus E PL2 ee T 05 pe i J I E p E n 8 S i a a m i T iy T b ja Paj u he d i X E T tis C ji Y f L 4 zt ij E E P z M T L sa 3 f F ta User Manual Table of Contents 1 Introduction 2 Specifications 3 Function Controls 4 Set up Instructions 5 Use amp Care of Housing 6 Service 7 Warranty 1 Introduction Made of sturdy 6061 aluminum 10Bar housing for the Olympus E PL2 is the ideal choice for those who favor small cameras Our housing is equipped with control buttons for all camera functions bulkhead connector for external flash and interchangeable ports for conversion lenses The clear acrylic back cover allows checking on the camera much easier For closure the double O ring and key hole lock design provide ease of use and added security Now you enjoy the use of a full function professional DSLR type housing built for a small camera 2 Specifications Test P Housings Individually Tested to 10 Bar 90 m 300 ft P E Recommended Working Pressure 60 m Closure Design Double O ring Key Hole Lock Body Material 6061 Aluminum Acrylic E e 185 x 171 x 146mm L x W x H with Zoom Port 116 x 171 x 146mm L x W x H with 20mm Port Total Weight Approximately 1 5kg Housing with Zoom Port Approximately 1 1kg Housing with 20mm Port Buoyancy with Camera Slightly Negative in Salt Water Spare Main O rings Included
4. is damaged or suspected of being damaged discard it immediately e Spare O rings are supplied with your housing or replacement O rings can be ordered from 10Bar e f the O ring is contaminated clean it with a clean cloth eRe inspect the O ring after cleaning Once the O ring has been inspected and verified good for use apply and distribute evenly a SMALL amount of silicone grease to the surface of the O ring e Replace the O ring into the groove e Run a finger over the O ring to make sure it is seated properly 13 5 Use amp Care of Housing Pre Dive Function Check eCheck O ring is in the groove on the housing and the clear acrylic lid eCheck housing is closed properly eCheck battery and memory card status on the LCD display eCheck control knobs and zoom function eCheck if sync port is properly connected or rubber protective cap is securely in place General Operations e The control levers and push buttons consist of internal double O ring seals on a stainless steel shaft This arrangement is very reliable As a precaution avoid excessively rapid movements when operating the controls causing possible deformation of the O rings e Also please allow for the fact that the camera takes a second or two to power up e If the camera does not appear to respond to a control action make sure that no other controls on the housing are pressed thus locking out other actions e Wear the wrist strap it is easy to inadvertently
5. let go of the housing if you are distracted e The body amp lid of the housing are made of 6061 aluminum and acrylic respectively 6061 aluminum is selected for its outstanding corrosion resistance strength and toughness while acrylic for its excellent transparency and having a high gloss surface Although acrylic and 6061 aluminum have good resistance to weathering long term exposure to sunlight should be avoided Avoid submerging the housing in hot water for a prolonged period of time or in a cleansing tank which is directly under a hot sun where the water may get heated Cleaning amp Storage e It is good practice to rinse off your housing with fresh water after every dive e Avoid exposure to fine sand e After a series of 10 or more dives e g after a dive holiday the housing should be immersed in warm water for 2 3 hours to dissolve any salt deposits that may have built up e No chemical cleaners should ever be used Important For long term storage please remove the O rings from the housing body and lid Transportation All external attachments should be removed and the housing wrapped in foam or bubble wrap for transportation Accidents The impact resistance of our aluminum housing is excellent In the event that your housing encountered an impact force e g being dropped the alignment of the housing may have been altered It 1s essential that you stop diving with the housing and send it to 10Bar immediately for se
6. Button 23 on the housing to adjust zoom and focus for this lens S a E N 1 S L x E a t 4 i whim AL S BALS iv bh Olympus M ZUIKO 14 42 f 3 5 5 6 Lens O Slide the Zoom and Focus Gear Rings onto the lens from the direction as shown by the red arrows below 6 Use Zoom Control Button 22 and Focus Control Button 23 on the housing to adjust zoom and focus for this lens ig I I pe ija EN I eo E e ou La Panasonic LUMIX G VARIO 7 14 f 4 0 ASPH Lens O Slide the Zoom and Focus Gear Rings onto the lens from the direction as shown by the red arrows below 6 Use Zoom Control Button 22 and Focus Control Button 21 on the housing to adjust zoom and focus for this lens LUMIX G VARIO 14 77 14 ASPH Panasonic LUMIX G VARIO 14 45 f 3 5 5 6 ASPH MEGA O I S Lens O Slide the Zoom and Focus Gear Rings onto the lens from the direction as shown by the red arrows below 6 Use Zoom Control Button 23 and Focus Control Button 21 on the housing to adjust zoom and focus for this lens Olympus M ZUIKO Digital ED 9 18mm 174 0 5 6 Lens O Slide the Zoom and Focus Gear Rings onto the lens from the direction as shown by the red arrows below 6 Use Zoom Control Button 22 and Focus Control Button 23 on the housing to adjust zoom and focus for this lens E 2 1 I I RP RB HR i 0 6 hR Dome Port for 8mm Wide Angle Conversion Lens 10 Mounting the Camera in the Housing Slid
7. e the hot shoe plug into the hot shoe as shown below ZR Mi K C ST L TTT T GR OT SHETE KR Eaei en n OD TER t AL ee Replacing the Lid e Replace the lid and make sure the lever is perpendicular to the side wall of the housing eLock the lid by pressing down the lever and turn until the lever is parallel to the side wall of the housing e After locking the lid make a final visual inspection of the main O ring for contamination 11 Note If the O ring has formed a good seal a continuous thin black line about 0 5 to 1mm in width should be visible where the O ring is in contact with the lid Follow this line all the way round the lid as a final check that the seal is good Maintaining the O rings The O ring is the main seal in keeping sea water out of the housing It is an effective barrier only if the O ring is properly maintained The O ring should be inspected before every dive The following information is provided for your guidance in using and maintaining the O ring e There are two O rings one on the lid and one on the housing which require regular maintenance e Remove the O rings periodically for inspection e It is not necessary to remove clean and re install the O rings after every dive provided the O rings are not contaminated e If the housing is to be opened between dives for changing memory card or re charging battery make sure the outside of the housing 1s thoroughly towel dried before opening e After s
8. ervicing the camera replace the lid right away e Before replacing the lid check the O rings and O ring recesses making sure that no contaminants such as dust hair salt sand etc has fallen onto them e The O rings should be inspected every time the lid is opened and maintenance carried out only if necessary 12 Inspection Cleaning and Re installation of the O rings Tools e Soft cotton buds that are free of chemicals or contaminants such as loose fibers e Silicone grease supplied with the housing or other types of silicone grease specifically for underwater camera equipment can also be used Procedure The following procedure should be carried out on a clean firm level surface e g on a table to prevent slipping especially when diving from a boat e The O ring can be extracted using the O ring extractor tool that came with the housing or push with the flats of both thumbs or index fingers to gently stretch the O ring on two adjacent sides thus making a small loop protruding around the corner The loop can then be grasped and the O ring pulled over the lip gar E T s a yT S er 9 Clean the O ring recess the square groove where the O ring sits with a cotton bud e Inspect the surface of the O ring for contaminants and damages such as cuts or tears This should be done visually and by running the O ring between thumb and index finger sensing any textural abnormalities on the surface If the O ring
9. ontinuous improvements on our products the latest model of the housing may differ slightly from those described in this document Copy to be returned to 10 Bar Underwater Housings Housing Type Date of Purchase DT I Owner s Address 16
10. ponsibility for ensuring the integrity of the watertight seal lies entirely with the user 10Bar accepts no liability for damage to or loss of any equipment used with or placed inside the housing It is highly recommended that an in water test of the housing without the camera be carried out before the first dive after changing ports or alteration of housing configuration This simple test can be done by lowering the housing with ballast to the expected diving depth and then retrieved to check for leaks Key hole Lock e The clear acrylic lid is secured to the housing by two key hole locks e Key hole locks are simple yet extremely secure mechanisms for locking down the housing lid Opening the Lid Make sure the flash on the camera is turned off before opening the lid Turn the levers of the locks perpendicular to the wall of the housing until the lock is released on both sides Pull out the lid by holding on the grip near the lock Use the universal key to insert in between the lid and body near the key hole lock to push off the lid if necessary Mounting the Gear Rings on the Lens In order to adjust the zoom and focus controls on the lens inside the housing gear rings have to be installed on the lens before mounting onto the camera Olympus M ZUIKO 14 42 173 5 516 II Lens Slide the Zoom and Focus Gear Rings onto the lens from the direction as shown by the red arrows below 6 Use Zoom Control Button 22 and Focus Control
11. rvicing Put a note inside the housing stating the nature of the accident to assist our technicians in assessing the damage 14 6 Service To ensure the continued performance of your housing it should be sent in to us for servicing annually or after every 200 dives whichever is earlier A full service will include e Inspect all components for wear or damage and report if repair is necessary Clean all sealing surfaces e Replace all O rings e Hydrostatic pressure test to 10 Bar Note Replacement of damaged components may require additional cost 15 7 Warranty The warranty is valid for two years from the date of purchase The warranty applies only to the housing itself 10Bar does not accept any liability either implicit or otherwise for any equipment housed inside or used together with the housing In the event of the housing flooded within the warranty period 10Bar will repair or replace the housing Disassembly of the housing will invalidate the warranty To register a warranty please complete the form below and return a copy by fax email or mail to 10Bar Underwater Housings Tel 852 2573 3228 Unit D 5 F Wing Hin Factory Building Fax 852 2811 9180 31 33 Ng Fong St San Po Kong Email service 10bar com Hong Kong Website http www 10bar com Copy to be retained by user Housing Type Date of Purchase DT oe Owner s Address Please keep this manual for future reference Note due to c
Download Pdf Manuals
Related Search