user's manual - Event Projection
Contents
1. ear Adjust the headset mic by pulling or pushing the wires until it fits tight How to adjust microphone boom amp cable NA TA F Position the microphone properly by pulling or pushing the boom along the slide Switch between left and right ear wearing style simply by rotating the microphone boom Hold on to the earhook while gently turning the boom For the dual ear versions also rotate the two earhooks Adjust the microphone boom to follow the shape of your face by gently bending the soft steel on the cable hanger Adjust the angle of the cable run also by gently bending the soft steel see ar rows Position the cable as shown on the picture for securing the position of the microphone The cable relief on the dual ear version should be fixed in the clip that also holds the two wires on the mount Service point for exchange of cables or booms The DPA d fine headset microphone offers exchange of cables or microphone booms Simply locate the service access point pull back the small protection cap and gently pull the boom away from the cable hanger Windscreens The enclosed windscreens offer additional protection against wind and pop noise Gently draw the windscreen over the microphone head For even better protection bigger windscreens are available Accessories see more at www dpamicrophones com Grids and windscr2. cations d fine omni headset microphone Directional characteristics Omnidirectional Principle of operation Pressure Frequency range 20 Hz 20 kHz Frequency range 2 dB 20 Hz 20 kHz with 3 dB soft boost at 8 15 kHz Sensitivity nominal 3 dB at kHz 6 mV Pa 44 dB re V Pa Equivalent noise level A weighted Typ 26 dB A re 20 uPa max 28 dB A S N ratio A weighted re kHz at I Pa 94 dB SPL Typ 68 dB A otal Harmonic Distortion THD up to 123 dB SPL peak up to 120 dB SPL RMS sine ynamic range Typ 97 dB Max SPL peak before clipping 144 dB Power supply for full performance Min 5V max 50V through DPA adapter for wireless systems 48 V phantom power 4V with DAD6001 BC XLR adapter i OAA Current consumption Typ 1 5 mA microphone 3 5 mA with DAD6001 BC XLR adapter Connector MicroDot Color microphone cable and earhook Black beige brown or lime no lime cable available Weight Microphone boom 0 8 g 0 03 oz Single ear hook 1 g 0 04 oz Dual ear hook 3 g 0 1 oz Cable 6 6 g 0 23 oz Total 8 5 g 0 30 oz Microphone head size h x w x d 9 5 x 5 3 x 2 9 mm 0 37 x 0 21 x 0 11 in Capsule diameter 5 4 mm 0 2 in Cable length 1 3 m 4 3 ft Cable diameter 1 6 mm 0 06 in Temperature range 40 C to 45 C 40 F to 113 F Relative Humidity RH Up to 90 Specifications d fine directional headset mi
3. crophone Directional characteristics Cardioid Principle of operation Pressure gradient Frequency range 20 Hz 20 kHz Frequency range 2 dB Near field 2 3 cm 0 8 1 2 in 100 Hz 20 kHz with 3 dB soft boost at 8 20 kHz Sensitivity nominal 3 dB at kHz 6 mV Pa 44 dB re V Pa Equivalent noise level A weighted Typ 28 dB A re 20 uPa max 30 dB A S N ratio A weighted re kHz at I Pa 94 dB SPL Typ 66 dB A otal Harmonic Distortion THD up to 123 dB SPL peak up to 120 dB SPL RMS sine ynamic range Typ 95 dB Max SPL peak before clipping 144 dB Power supply for full performance Min 5V max 50V through DPA adapter for wireless systems 48 V phantom power 4V with DAD6001 BC XLR adapter a J Current consumption Typ 1 5 mA microphone 3 5 mA with DAD6001 BC XLR adapter Connector MicroDot Color microphone cable and earhook Black beige brown or lime no lime cable available Weight Microphone boom 0 8 g 0 03 oz Single ear hook 1 1 g 0 04 oz Dual ear hook 3 g 0 1 oz Cable 6 6 g 0 23 oz Total 8 5 g 0 30 oz Microphone head size h x w x d 9 5 x 5 3 x 2 9 mm 0 37 x 0 21 x 0 11 in Capsule diameter 5 4 mm 0 2 in Cable length 1 3 m 4 3 ft Cable diameter 1 6 mm 0 06 in Temperature range 40 C to 45 C 40 F to 113 F Relative Humidity RH Up to 90 w suyp idp
4. e them to break over time DPA d fine headset microphone comes with a number of cable steer clips in different colours Mounted on the cable relief this clip allows for quick recognition of a specific headset microphone Service amp repair If you are not satisfied with the characteristics exhibited by this product please go to www dpamicrophones com service for instructions Clothing clip The supplied clothing clip allows you to attach the cable to your clothes thus relieving the cable draw to the headset mic This is essential on the single ear headset mic Warranty The d fine headset microphone is covered by a two year limited warranty Frequency response d fine omni headset microphone 10 dB 10 20 30 20 Hz 50 100 200 500 1 kHz 2 5 10 20 40 Frequency response d fine directional headset microphone 10 dB 10 20 0 20 Hz 50 100 200 500 1 kHz 2 5 10 20 40 Black line is near field 2 3 cm 0 8 1 2 in Green line is far field more than 30 cm 12 in Copyright 2012 CE H CE marking This product conforms with all relevant directives approved by the European Commission Product features and specifications are subject to change without notice Specifi
5. eens cables and adapters booms and earhooks Sweat stop amp protection grid The microphone is equipped with a transparent sweat stop around the micro phone boom to prevent sweat running along the microphone boom to the microphone head A protection grid is mounted over the microphone head If clogged with dirt or make up gently remove it and clean it with distilled water Always leave the protection grid on the microphone as it protects the inner grid and offers protection against wind and breathing noise The protection grid is replaceable Protection cap DPA d fine headset microphone comes with a red plastic cap which serves to protect the microphone head when putting on make up hairspray and more Remove the cap before use Color codes amp cable steer Maintenance DPA d fine headset microphone is resistant to high levels of humidity However care must be taken to keep the headset microphone away from exposure to water and cleaning fluids and to keep the microphone head dry at all times Do not use spray or fluid containing chemicals that could remove static electricity on or close to the microphone This could cause permanent damage Cable maintenance Use organic oil e g olive oil or lukewarm distilled water to remove residue from tape glue or make up on the cable Do not bend the cable or rub it harshly it may stress the inner cores of the cable and caus
6. user s manual d fine headset microphone Dual ear Single ear Short boom Omnidirectional characteristics e The microphone is sensitive to sound from all directions e The sound remains more or less the same regardless of the distance between the sound source and the microphone e The positioning of microphones with omnidirectional characteristics is less critical than with directional e An omnidirectional microphone is generally not very sensitive to wind breathing and handling noises Directional characteristics e Rejects background noise and creates higher separation e The microphone is most sensitive to sound on the side of the chevron e The positioning of mics with directional characteristics is essential as the low frequency level will change according to the distance to the mouth Choose a distance which yields the desired amount of bass e Care should be taken to protect against wind and pop noise The directional characteristics of the microphone is indicated on the microphone head with for omnidirectional and gt for directional This marking should always point towards the mouth How to mount the DPA d fine headset microphone For the single ear just open the spring hook lightly first place the slide behind your earlobe and let go of the spring over you ear For the dual ear place the headset behind your ears and place the springs ike for the single
Download Pdf Manuals
Related Search