User Manual - Marshall Electronics
Contents
1. Marshall Electronics Broadcast A V Division VS PTC 50 Camera PTZ On Screen Display Menu Mini Joystick Controller User Manual Thank you for purchasing this Marshall Electronic s product Please read the User Manual thoroughly before attempting to setup use If you have any problems with this product please contact Marshall Electronics Tel 800 800 6608 310 333 0606 Caution The LCD screen can be damaged by excessive pressure direct sunlight or liquids Joystick and keyboard should be used in environments within the temperature and humidity range specified Please follow instructions defined in this manual for setup and operation List Of Items 1 Power adapter Input 100 240VAC 50 60Hz Output DC 12V 2 Users Manual Keyboard Specs Item Parameters Power Supply DC12V 1A 10 10 C 55 C Humidity lt 90 RH No cream node RS485 Half duplex 2400bps 4800bps 9600bps 19200bps 38400bps 128 32 LCD screen 180 L x 165 W x 90 H mm 1 1 Function Keys On Front Panel 1 Joystick 2 LCD screen 3 Function keys 4 Speed dome Setup and recall keys Esc Setup F1 Preset Shot Pattern Run 0 9 Auto Cam Tele Wide Open Close Far Near Aux on Aux off Aux off Exit key exit and back to previous menu Setup key press and hold for 3s to se2. acklight default factory setup The following example is default factory setup operation steps In normal status press and hold Setup key for more than 3s LCD will Display Press joystick finish setup and back to select PTZ ID menu repeat above steps you can set other PTZ parameter After finishing all setup press ESC key to quit setup Press joystick the buzzer will give out long time sound the question mark in screen will disappear denote setup finished press ESC key to quit setup 3 3 Parameter Setup Framework 4 Typical connecting diagram Pelco D PelcoP PTZ addr xxx protocol ps y EFi 0 2 IE HIK DAHUA ani Electronica E DC connector PTZ addr 0 254 2400 4800 9600 Baud rate J A dadi ae D all PTZ parameter will be set as same 19200 38400 TERA f VS PTC 50 Chinese English Move joystick to select Gamera 030 Controller Old password 4 digit number RS 485 connection Teminal A password setup 4 digit number RS 485 connection Teminal B Enter again 4 digit number gt ns pide A B A B A B setup Key press ciose low mid high Move joystick to select A gt eN Rey OCIO close 305 605 Move joystick to select Can connect max 255 cameras Power supply cable DC 12V optional 1205 open Default factory Move and press setup joystick to select 5 FAQ Symptom Analysi
3. out keying in any number the controlled ptz ID will take away 1 Press and hold for 3s to recall number 95 preset normally it will be opening the menu of ptz 1 2 LCD Screen Pressing and holding each function key will engage the LCD screen and relevant information will appear When function keys are released they will disappear When there is no operation within 30 seconds the LCD and keyboard will go into power save mode backlight will turn off and standby image will appear 1 3 Joystick Control When control speed dome and mounting plate Output Output Control Control Output Output operating Control Control Output Output Output Output uperatmg Control Control Control Control Menu F Parameter Parameter turned up A of the left of the right KEYBOARD CONTROLLER OPERATIONS 2 1 Introduction to single press keys and combined keys 2 1 1 Single press key When single key is pressed the corresponding PTZ will respond Single press keys include Near Far Tele Wide Open Close Auto F1 Run Esc joystick 2 1 2 Combined key operations mean 2 or more keys or key and joystick are pressed the corresponding PTZ will respond Single press keys include Near Far Tele Wide Open Close Auto F1 Run Esc joystick The operations include Preset Pattern Shot Cam Setup 2 2 Detailed introduction to combined keys 2 2 1 Select PTZ ID select speed dome or decoder whose ID is 28 pres
4. s Methods Step 1 i Chockihe oe and B is reversed ATI ete Check RS485 cable Keyboard continuity is OK or not Controller cannot control the speed dome 2 Check the software settings keyboard controller and speed dome address protocol baud rate Step 1 check the current protocol and baud rate is correct or not Step 2 Restore the settings to default setting and reset 1 Check hardware Check the continuity of each branch cable 2 Check software Check the protocol and baud settings rate of each address code Some speed domes can be controlled but some not Step 1 Connect RS485 to a 1200 resistor at far end Step 2 Install RS485 distributor between the speed dome and keyboard controller 3 Might be the problem of star type connection Many speed domes respond simultaneously Check the ID when operate of speed domes the keyboard controller No key tone Turn on key tone in system settings Check whether those speed dome that respond simultaneously have the same address code or not Set different address Marshall Electronics Inc 1910 East Maple Ave El Segundo CA 90245 Tel 800 800 6608 310 333 0606 Fax 310 333 0688 www LCDracks com e support marshall usa com
5. s 2 8 Cam in turn LCD will display as below corresponding protocol and baud rate will also be showed 2 2 2 Set and recall pattern Set pattern select PTZ addr press Pattern key and hold for more than 3s LCD will display Operate joystick to control PTZ moving to relevant position adjust zoom time After setup press Pattern key to finish LCD will display Recall pattern press Run key PTZ will run in the certain route which recorded in relevant pattern Press any single press key will stop pattern scan and back to normal status Note This keyboard supports setting one pattern at present 2 2 3 Set and recall preset point Set preset point 1 key in 1 press Preset Recall preset point 2 key in 2 press Shot 2 2 4 Turn on Turn off aux function Turn on need to open number 1 aux function press 1 press AUX on Turn off need to close number 1 aux function press 1 press AUX off 3 1 Parameter Setup amp Inquiry Note If you want to set all PTZ s protocol and baud rate as same when you select e g change the protocol of PTZ 28 to PelcoP baud rate to 9600 PTZ 1D in setup menu please select 0 255 details as below in normal status press and hold Setup key for more than 3s LCD will display Follow above steps all PTZ s protocol and baud rate will be set as same 3 2 System Parameter Setup System parameter including language password key press volumn key b
6. tup keyboard s parameter Adjust the control speed it has 4 level 1 2 3 4 Preset special status of ptz including direction and zoom times This key should be used together with number key Recall special status of ptz including direction and zoom times This key should be used together with number key Start stop pattern record press for 3 seconds to start pattern record after all operation press this key again to stop pattern record this key should be used together with number key Recall the stored pattern this key should be used together with number key Number key 0 1 2 3 4 5 6 7 8 9 Control ptz rotate in horizontal direction automatically or clear input number when user input some numbers press this key can delete the numbers else it will control ptz rotate in horizontal direction automatically Address selection key select ptz address this key should be used together with number key Zoom in zoom in the object enlarge the object size Zoom out zoom out the object reduce the object size Iris enlarge iris Iris reduce iris Focus adjust the lens focus on distant object Focus adjust the lens focus on near object Aux on turn on ptz s aux This key should be used together with number key directly press this key without keying in any number the controlled ptz ID will add 1 Aux off turn off ptz s aux This key should be used together with number key directly press this key with
Download Pdf Manuals
Related Search