Home

Kayfun-Mini v2.1 ES - User Manual Кайфун

1. E liquid dripped on the wick 20 25 drops and the body work as a evaporation chamber This mode useful for a quick change of taste when testing different e liquids Wick coil assembly is installed The top body part 3 is screwed in atomizer base 1 then top cap 4 and mouthpiece 5 are screwed onto each other Dissembling happens in the reverse order Assembling Standard mode Wick coil assembly is installed Evaporation chamber 2 with short cap of the evaporation chamber 2b is screwed in atomizer base 1 then bottom transparent or metal 3b body part top body part top cap 4 and mouthpiece 5 are screwed onto each other Dissembling happens in the reverse order Assembling Long mode Wick coil assembly is installed Evaporation chamber 2 with long cap of the evaporation chamber 2 is screwed in atomizer base 1 then bottom transparent or metal 3b body part then another bottom transparent or metal 3b body part top body part top cap 4 and mouthpiece 5 are screwed onto each other Dissembling happens in the reverse order Seite 12 von 21 Filling e liquid Kayfun mini filling can be done in two ways Method 1 classic Unscrew the cap 4 e e liquid into the space between the body 3 and vaporization chamber 2 e Screw the cap back on Method 2 through the valve For the filling through the valve you will need a
2. blow Kayfun mini through the air intake 1C the excess of e liquid from evaporation chamber will flow out through the mouthpiece to the napkin Seite 13 von 21 Before operating Kayfun mini After assembling the coil evaporation chamber and collector tank it is recommended to check atomizer resistance Resistance should be measured between the screw 1h and the bottom part of the atomizer 1a You should fix detected short circuits before you start using the atomizer on battery mod Never use shorted Kayfun mini on unprotected battery mods this can cause damage of the mod and even fire Places where short circuit may occur causes and remedies For starters inspect Kayfun mini for the presence of foreign metal objects that can cause a short circuit and remove them Place reason too long ends of the coil are shorting to the walls of the evaporation chamber or the opposite pole Solution Cut ends of the wire so they would not stick out from under the screw heads Place reason Coil lies too low on the air duct and touches the poles by middle coils Solution Lift the coil Place reason Coils touch each other Solution straighten the coils so that neighboring coils do not touch each other Place reason The screw 1b is screwed in too far touching the center pin 1h Solution Unscrew 1b so that it does not touch the center pin 1h Place reason one of the insulators 1j or 1m is damaged Solution Replace t
3. 5 3 3 3 2 3 0 2 9 2 8 27 26 2 6 74 6 9 6 4 6 0 5 7 5 3 51 4 8 46 44 4 2 ees ora 52 5 0 iz 22 ss ea sa sa 5 0 LIII na sajas aa m m o N mam YIN gg gt Gn On jeje 6 0 6 3 6 6 7 6 N w N NJN gt 3 7 7 a 12 16 7 7 7 5 7 3 7 6 9 Useful links and information See this User Manual on line in forum svoemesto ru http forum svoemesto ru showthread php t 523 You can purchase Kayfun in following online shops Russia http shop svoemesto ru http flavourartexpress ru Belarus http stepanoff by Ukraine http eflavour com ua Germany _http digitalsteam de http www intaste de Switzerland http dampfzauber ch UK http www cloud9vaping co uk Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 21 von 21
4. quickly get used to this type of draw and will get the most from your Kayfun mini Seite 18 von 21 Minor leaks may also happen if the tank is filled completely or it is filled more than halfway while Kayfun mini is lying horizontally or with mouthpiece tilted down for some time In this case one of the grooves 11 could be at the top in the air and another one at the bottom dipped into e liquid In this case the air will escape from evaporation chamber through the top groove and e liquid will flow from the tank to the evaporation chamber through the bottom groove Naturally this process stops as soon as both grooves are covered with e liquid Make sure that both grooves are always covered with e liquid keep Kayfun mini horizontally in such a way that the mouthpiece is always slightly higher than the evaporation chamber Even better keep it in the vertical or near vertical position if your battery mod allows it Leaks may also happen when ambient temperature and or pressure changes abruptly for example when you walk into a heated room from the cold or in an airplane during takeoff landing It may even happen during rapid ascent descent in express elevator Solid metal parts of the device are expanding shrinking with temperature pressure change changing the volume of the tank and causing e liquid to flow into the evaporation chamber Pressure drop causes the process similar to what happens when you draw just without heating the co
5. the posts 1e and 1f at the level of the air duct or even higher Liquid begins to flow from the wick to the poles and then into the duct In this case the duct becomes kind of extension of the wick The same happens when coil lies too low over the air duct swollen with liquid wick can stick out between the coils and touch the poles What to do shorten the wick position it correctly on the sides of the poles lift coil higher over the air duct The reason With each draw evaporation chamber receives more e liquid than can be evaporated as a result e liquid floods the evaporation chamber and flows through the duct into the collector tank There may be several reasons for this Reason number 1 insufficient heating temperature or rather lack of power voltage to the coil when coil can t heat up to required temperature What to do Increase the power voltage on the battery mod or build a coil with less resistance Probably batteries are depleted charge replace battery if it is the case Reason number 2 Too strong long draw What to do Unscrew 1b for lighter draw Try to inhale slowly and smoothly You need to get used to the lighter draw especially if you are used to hard draws of conventional cartomizers and tanks Find comfortable for your strength and duration of the draw that would at the same time allow all e liquid entering the evaporation chamber to evaporate during the draw and Kayfun mini would not overflow slosh You will
6. 4 0 mm 24 1 g 25 drops Standard 60 5 mm 24 1 g 2 8 ml Long mode 102 0 mm 39 7 g 6 0 ml O Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 3 von 21 Atomizer Svo Mesto Kayfun mini v2 1 ES hereinafter Kayfun mini consists of the following components Base e 2 Evaporation chamber 3 Body 4 Top cap 5 Mouthpiece O Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 4 von 21 1 Atomizer base Atomizer base 1 is the most important and most complex part of the device E Ou Bottom part of atomizer Air adjustment screw The air intake O ring ensuring the tightness of the contact with the body 3 Negative pole Positive pole Coil screws Central pin screw Grooves for supplying liquid from the tank to the evaporation chamber 2 and air outlet from the evaporation chamber to the tank Positive pole insulator 1f Refilling valve E liquid duct Liquid flows through it into the tank when filling through the valve 1k e Im Center pin insulator 1h Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 5 von 21 2 Evaporation chamber Evaporation chamber 2 consists of the following components 2a The body of the evaporation chamber 2b The cap of the evaporation chamber 2c Thelong cap of the evaporation chamber The body of the evaporati
7. Kayfun Mini v2 1 ES User Manual v2 1 ES by SMtec GmbH SvoeMesto Ltd Table of contents Bee User IM an tial 1 Specifications sn n a c CS a 3 5 2 Evaporation 6 3 Atomiver DOdy eese tede uds edu tylstix ua iic Guede ale EI EIU 7 AP TOP BaD be RUM rH PEE EU E 8 CS Mouthpiece mot included 9 Wrappi g the 10 Principles of 11 Assembling oce casu ep rH EO Yen dae 12 DE M n rc 13 Before operating a 14 Operating ayf n mini AT 14 Servicing MiNi 15 Dry tala ae 15 General AU VICES M 16 Possible problems and their sepe vote pd emet 18 P MEN 21 Useful links and 1 eec ere ee ata Rec redi Sacto toe 21 Seite 2 von 21 Specifications Material Stainless Steel The material of the transparent body Polycarbonate Diameter 14 mm Diameter of the transparent body 15 mm Connector Type 510 Dimensions not including connectors and mouthpiece weight volume Drip mode 3
8. bottle with a thin plastic nose Nose diameter should be suitable to the filling port Turn Kayfun mini mouthpiece down Insert the nose of the bottle in the valve opening 1k e Fill the tank by squeezing the bottle The air will escape from the tank into evaporation chamber through the same grooves 1i Take out the nose of the bottle from the valve turn Kayfun mini mouthpiece up When refilling using method 1 it is important to consider that the tank is no longer air tight This will enable the e liquid to flow into the evaporation chamber through the grooves 1i When the cap is screwed back onto the device this can also form a small amount of pressure which forces a bit of the e liquid into the evaporation chamber Both effects can potentially add up to produce a small amount of flooding in the evaporation chamber This technique can take a bit of practice and should be conducted in a timely manner When refilling using method 2 it is important not to overfill the tank Over filling the tank can produce flooding in the evaporation chamber A small amount of air must remain in the tank to allow the pressures of both the evaporation chamber and the tank to equalize during the inhalation process by way of the ducts It is recommended to leave approximately 2 3 mm of space at the top of the tank Excess of e liquid can be removed from the Kayfun mini this way 1 turn Kayfun mini mouthpiece down 2 put a napkin under mouthpiece
9. f flavor and burnt taste If you are using a battery mod that has variable wattage feature you can set desired power directly on the device If you are using variable voltage battery mod measure the resistance of your coil and calculate required voltage using following formula Voltage square root of the power multiply by the resistance U V P Of course you can also find comfortable voltage using old school trial and error method If you are planning to use Kayfun on mechanical mod or other fixed voltage device calculate the target coil resistance based on desired power and voltage of your device and then build the coil with target resistance For example when using the battery mod stabilized at 3 7 volt coil resistance of 1 6 ohms will give you 8 56 watts of power it is in the comfort zone To quickly calculate the power voltage resistance refer to the following table in the appendix Press draw release Use the rule of Press draw release This means that you should press the power button before the draw and release it after the draw This will give the coil time to heat up before draw and evaporate excess of e liquid after it Do not fill the tank to the top When refilling leave small amount of air in the tank so there is something to expand during the draw and e liquid could flow into evaporation chamber When refilling through the valve stop when e liquid covers the transparent ring when re
10. filling through the top cap leave 2 3 mm of air at the top of the tank Seite 16 von 21 Keep it clean Disassemble and wash Kayfun mini periodically change Dry burn the coil check the integrity of the o rings Treat with care Treat Kayfun mini with care do not throw or drop it it can cause damage and negative impact on the appearance Do not use for other purposes Kayfun mini is designed for vaping only don t fill it with liquids not intended for vaping Be careful with organic wicks Be especially careful if you are using organic materials such as cotton for building your wick These materials in contrast to silica are combustible and dry burning can t be used with them Make sure there is always enough liquid in the tank and that organic wick is soaked with e liquid all the time Using SS mesh wick Oxidized stainless steel mesh wick may be used in Kayfun but this is not an intended operation mode for the device Consistency of operation and overall functionality of the device in this case is not guaranteed although it may work fine Seite 17 von 21 Possible problems and their solutions The problem Short circuit no contact What to do see Before operating Kayfun mini The problem Kayfun mini sloshing flooding liquid accumulates in the collector tank and even flows out through the duct hole First you need to check if the tank is airtight If the tank is not sealed e liquid will pour out of it in
11. he insulator If the meter on the contrary shows the infinite resistance check the coil for breaks Operating Kayfun mini Adjust draw tightness to comfortable level using screw 1b Keep in mind that too strong draws can cause flooding of the evaporation chamber Seite 14 von 21 Servicing Kayfun mini Kayfun mini servicing includes its regular refilling cleaning washing replacing and dry burning the coil Refill Kayfun mini as needed e Periodically disassemble and wash Kayfun mini under running water We recommend doing this every time before switching to e liquid with different taste Periodically change the coil With the lapse of time sludge deposits can accumulate on the coil wire which has a negative impact on the taste This sludge can be removed by Dry Burning Dry burning e Remove the lid drain the excess of e liquid from the tank remove the evaporation chamber e Soak up remaining liquid from the coil and wick with a cloth Screw Kayfun mini onto the battery as it is e Press and hold the battery power button for 5 7 seconds to let the coil heat up then release for 5 7 seconds e Repeat this procedure till all e liquid has evaporated from the wick and all deposits burned off the coil Please note that in the process of dry burning wick gradually loses its ability to absorb liquid So after 3 5 dry burns we still recommend to replace coil and a wick Seite 15 von 21 General advices Find comfor
12. ht connection with the cap of the evaporation chamber 2 Cover 4 is screwed onto the body 3 with the top of the evaporation chamber 2b 2c resting against o ring 4c O Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 8 von 21 5 Mouthpiece not included Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 9 von 21 Wrapping the coil The coil is made of resistance wire wrapped around the wick folded in several layers of silica rope The ends of the wire are fixed under the cap screws 1g The coil is located diagonally between the screws 19 at 1 5 2 mm above the air duct 1h so that incoming air is distributed evenly round the coil when the user inhales Tails of the wick fit in the free space along the sides of the poles and 1 so that they are above the grooves 11 but don t get into them Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 10 von 21 Principles of operation Atomizer is from the word atomize meaning to break down into atoms The atomizer contains resistance coil that is energized using an attached battery When the coil is covered with e liquid and the battery is engaged the coil heats up quickly and boil the lower layer of e liquid This vaporization or so called Explosive evaporation forms a steam cocoon around the coil This cocoon rises and expands in volume atomizing the up
13. il To avoid leakage in such cases we recommend you to keep transfer Kayfun mini upside down i e mouthpiece down In this case grooves 11 will be at the top in the air bubble and when the temperature or pressure changes air will flow between evaporation chamber and tank instead of e liquid The problem Burnt taste This problem is opposite to the leakage Dry wick is the most common cause of burnt taste The reason Too high heating temperature to be exact excessive power voltage is applied to the coil This heats up the coil above desired temperature What to do reduce the power voltage on the battery mod or install higher resistance coil The reason No liquid left in the tank What to do Refill the tank The reason Tails of the wick are packed too tightly in the evaporation chamber What happens Too tightly packed wick may block grooves 1i and obstruct e liquid flow from the tank to evaporator chamber What to do Place wick properly It must lie free over the grooves 1i but should not be pressed against or stuck into them The reason The grooves 1i are blocked What happens Pieces of wick are stuck in grooves 11 What to do Remove pieces of wick from grooves 11 The reason Holding Kayfun mini upside down mouthpiece part down all the time for example when lying down What happens In this position liquid does not cover grooves 11 As a result liquid doesn t flow into evaporation chamber and doe
14. inciple When the user initiates the inhalation process negative pressure is formed inside the evaporation chamber which draws a small amount of e liquid through the grooves 1i into the evaporation chamber where it gets absorbed by the wick located directly above these grooves Low pressure is produced in the tank due to the transfer of e liquid to the evaporation chamber When the user has completed the inhalation process the pressure in both the evaporation chamber and the tank are normalized due to the air being passed back into the tank through the ducts During the inhalation process the evaporation chamber receives liquid from the tank through the grooves 11 and after the inhalation the tank receives air from the evaporation chamber This process can be visually observed as air bubbles rising from the grooves in the tank provided the transparent ring is being used E liquid that entered the evaporation chamber during the inhalation is absorbed by the wick The wick is saturated and distributes e liquid over the coil The coil heats up and atomizes liquid At the next inhalation this cycle is repeated until there is no more liquid in the tank or the battery is depleted Seite 11 von 21 Assembling Kayfun mini Kayfun mini assembly occurs in the order in which the details are numbered You can assemble 3 modification Drip Standard and Long Assembling Drip mode In Drip mode no evaporation chamber using
15. on chamber 2a is screwed to the atomizer base 1 The cap of the evaporation chamber 2D or 2 is screwed onto the body of the evaporation chamber 2a Combination with a short cap of the evaporation chamber 2b is used in standard mode a combination with a long cap of the evaporation chamber 2 is used in the long mode Evaporation chamber is made of two parts to simplify wick installation and a chance to collect a standart and long mode Attention the long cap of the evaporation chamber 2c is not included in the base kit O Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 6 von 21 3 Atomizer body Atomizer body 3 consists of the following elements The bottom transparent body part 3b The bottom metal body part e The top body part e 3c O rings to ensure tight seal between 3b Attention the bottom transparent body part 3a is not included in the base kit The bottom transparent body part allows you to visually monitor the amount of liquid in the tank the bottom metal body part provides the highest reliability WARNING the transparent body is a consumable item and is not covered by the manufacturer s warranty Svo Mesto Ltd amp SMtec GmbH 2013 PDF created by Kilian Spohr Seite 7 von 21 4 4 consists of 4a Cap 4b O ring ensures tight connection to the body 3 4c O ring ensuring tig
16. per layer of e liquid on the coil This subsequently produces a mixture of steam and dispersed liquid particles which we perceive as a smoke Since there is no combustion used in this process the result of atomization is not smoke but vapor to be more accurate fog The e liquid is stored in the tank system which is located between the walls of the outer chassis and the evaporation chamber The evaporator chamber 2 has special grooves 11 that serve as ducts for e liquid to flow into the evaporation chamber which is mounted to the atomizer base 1 The tank is sealed and air tight when the cap is closed so liquid does not flood the evaporation chamber through these grooves air pressure inside the tank prevents it Drinking bowl for birds works on the same principle liquid does not come out of turned upside down water filled bottle if you deep bottle neck in a bowl of water Water comes out of the bottle only when the level of liquid in the bowl drops below the level of the bottle neck then some amount of water will pour out fill the bowl up the bottle and then stop again Another example Take a straw deep half of it vertically in the water close the top opening of the straw with your finger and pull it out of the water Low air pressure at the top of the straw will hold water in it but as soon as you release your finger the sealing of the air bubble is broken pressure equalizes and water discharges Kayfun works on the same pr
17. s not saturate wick during the draw What to do Do not use Kayfun mini in this position The reason Too long piece of the resistance wire is left between the screws and the wick What happens The pieces of resistance wire that don t contacts the wick get easily overheated What to do Adjust the coil position to eliminate long resistance wire legs not contacting the wick Seite 19 von 21 The reason Resistance wire is wrapped too loose around the wick What happens Coils that don t contact the wick get easily overheated What to do Rebuild coil correctly resistance wire should have contact with the wick along the length of the coil The reason Resistance wire is wrapped too tight around the wick What happens Resistance wire pinches the wick and obstructs the flow of e liquid along it this can be the reason of burnt taste What to do Rebuild coil correctly resistance wire should not pinch the wick The problem Burnt taste and flooding at the same time The reason Yes this can also happen if during assembly you don t place tails of the wick along the grooves but leave them lifted This is usually done out of habit wick tails are placed this way in some popular cartomizers What happens In this case when you draw liquid flows into evaporation chamber does not find wick tails to suck into they are raised up eventually rises over the air duct level and overflows Meanwhile coil remains dry causing burnt taste Wha
18. t to do Install wick correctly The problem The draw is too tight even when 1b is completely unscrewed The reason Very large coil and or wick What happens Air flow in evaporation chamber gets obstructed What to do Setup the coil and wick correctly The reason The blockage of the air duct 1h What happens Something obstructs the airflow through the duct What to do Remove the obstruction WARNING Some flavorings that make up liquids for electronic cigarettes have a devastating impact on the polycarbonate material transparent ring 4b is made of If you use such a liquid please use metal ring instead of polycarbonate ring in order to avoid breakage The manufacturer is not responsible for the destruction of a transparent ring due to usage of aggressive flavors and reminds you that the transparent ring is a consumable item and is not covered by the warranty by the manufacturer Seite 20 von 21 Appendix power voltage resistance table 8 12 4 0 11 12 13 14 1 5 1 6 4 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 2 3 3 54 3 5 7 5 6 9 6 4 6 0 5 6 5 3 5 0 47 4 5 amp 3 4 1 3 9 3 8 3 6 3
19. table nicotine level When you use Kayfun mini for the first time try to start from nicotine level twice less than you used to For example if you used 12 mg ml liquid start from 6 mg ml on Kayfun mini Kayfun mini has excellent nicotine delivery and vapor production capabilities so it is easy to get nicotine overdose for want of habit Choose optimal for you nicotine level but we do not recommend using e liquid with level higher than 12 mg ml with Kayfun mini it can be dangerous to your health Find comfortable strength and duration of the draw When using Kayfun mini draw should be different from what you got used to with conventional cartomizers and tanks It has to be smoother and lighter Remember that the stronger tighter you make a puff the more liquid comes into the evaporation chamber and the greater the chance of overflow Find comfortable for your strength and duration that would allow all e liquid entering the evaporation chamber to evaporate during the draw Find comfortable power level voltage resistance Power P is the ratio of the square of the voltage U to the resistance P U R If you have a 2 ohm resistance coil and the battery produces 3 7 volt power is equal to 3 7 3 7 2 6 85 watts In practice the comfort zone for most of vapers is somewhere between 8 and 12 watts Less than 8 watts will result in low vapor production and nicotine consumption More than 12 watts can result in the loss o
20. to evaporation chamber by the principle of communicating vessels and then it will flow into collector tank through the air duct 1h Check if evaporation chamber 3 is firmly screwed to the base all o rings are in place and intact 1d 3d 4b and especially 4c O ring 4 is the easiest one to lose during dissembling assembling Also make sure that the transparent ring 3a is not cracked in case you use it Another place where the air tightness may be compromised is refilling valve 1k It should let e liquid air to flow outside in but not inside out Test it by trying to blow in the hole 11 the valve should not let air to go through If it does try rinsing the valve with water it is possible that dirt mote got into it You can use refilling bottle for rinsing the valve fill the bottle with water insert the nose into the valve and pump liquid through the valve back and forth Rinse till the liquid is able to flow outside in only If you are sure that the valve is faulty contact the seller manufacturer for repair replacement If you have verified that the seal is not broken but the problem still persists let s try to find and eliminate the cause There may be several more reasons for leaks The reason Wick is too long and or coil lies too low over the air duct What happens If the wick is too long and it takes all the available space in the evaporation chamber then when swollen with e liquid it leans to

Kayfun-Mini v2.1 ES - User Manual Кайфун

Contents

Download Pdf Manuals

Related Search

Related Contents