Home

User Manual

1. Fig 4 7 3 Paper outlet position lt PRESENTER turning spaces They are a group of spaces relating to Presenter Presenter could operate shown as below Fig 43 BK T080 user MANUAL 1 Fig 4 7 4 Presenter spaces for operation Shown as 1 item in the Fig above Presenter could accommodate paper shortly in the printing so that paper shall stick up as 1 item in the Figure Here enough space should be reserved the height is at least 100mm to ensure paper presenting smoothly Shown as 2 item in the Fig above After Presenter finishes the printing the paper which is not needed shall retract shown as 2 item in the Fig above Therefore enough space should be reserved and waste collection device is designed to keep the retracted paper The size is shown in Fig 4 7 2 Shown as 3 item in Fig above When the paper is jammed at Presenter the user needs to turn up the top cover at the front of Presenter to take out the jammed 44 SN3IC BK T080 user MANUAL paper Here enough space should be reserved in order to turn up the top cove and for users operation 4 Shown as 4 item in the Fig above To remove the paper jam at the platen and turn up the whole Presenter here enough operation space should be reserved Paper holder turning space a
2. cococccccccniccnnccnnccnnicinininicininnn 25 3 3 1 Exterior of print unit and controlling Parts oonococcnnnnccccc 25 3 3 2 Print unit explanali0N oooooononicocccinnncconananonccncnncarnnnananncncnncnnns 26 Ed EL A e 2ccncehabied evel peneeiant aese raataa 27 3 5 Paper holder ccoo ata rd da dla 29 9 0 Interface iii rada oia 30 INSTALLATION AND SUGGESTION 005 31 4A UMPACKING PR PU O aa a E Raada 31 4 2 Adjusting paper near end SENSO coooccccncccncccnnconcconccinnconocinncinnss 31 4 2 1 Detection range of paper near end SenSoft ooocococicicccccccccincnn 31 4 2 2 Adjusting paper near end SONSOF cocoooocccoccccccccccccaonannnonnnncinnnns 33 4 3 Connecting the grounding Wil8 oooooconnonccicinacocccconnoncnnnnanannonnns 34 6 SNIC BK T080 user MANUAL 4 4 Connecting the AC power adapter cceeeceeeeeeeeeeeeeeeeees 35 4 5 Connecting interface Cable c cccccceeeeeeeeeceeeeeeeeeeteeeeneaees 36 4 6 Assembling and feeding paper roll ccceeceeeeeeeeeeeeeeeeeees 37 4 6 1 Assembling 6 0 ee 37 4 6 2 Loading pap ou cescsececcccceecensnneeceeeeesetensaaeeceeesesetseseneaaeeenenes 38 4 7 Installing the printer cent nono 40 4 7 1 Installation NOTICE ooooncncnninicicicinnnnnonanananccncnncannnnanarncncnannnn 40 4 7 2 Keep space for printer installation oooooooocccnnncininccccccccnnccacnn 40 4 8 Installing printer driver
3. C Search removable media floppy CD ROM Include this location in the search C 1Setup BK TO80 EN V1 011USBDRY2 20 w _ Browse Dont search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for pour hardware lt Back Next gt Cancel e Click Finish to end the installation Hardware Installation The software you are installing for this hardware USB Device Driver for POS KIOSK Printers has not passed Windows Logo testing to verify its compatibility with Windows lt P Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation 58 SN3IC BK T080 user MANUAL Windows Server 2003 e Connect one USB printer to the host and insert USB connecting line to the idle USB of the host The system could find USB device and pop up the driver installation guide Install from a list or specific location and click Next e Select Search for the best driver in these locations also select Include this location in the search then click
4. Cancel C 50 SNC BK T080 user MANUAL e Select the installation mode Typical and click Next J Install Driver for Printers og Setup Type Typical C Advanced Remarks Install default printer driver Press F1 for help lt lt Back BJ i e The driver identifies the current system type then click Next nsta river for Printers H E gt Select Install OS C Windows 98 Me Windows NT C Windows 2000 Windows XP Windows Server 2003 Press F1 for help lt lt Back B i gt Cancel C e Set the printer port and the system default LPT1 as the print port Users should choose the installing port according to its use sI SNIC BK T080 user MANUAL Under windows NT4 0 or above select BYCOMx as Serial driver X equals to 1 2 3 4 5 6 7 or 8 then click Finish to end the installation q Install Driver for Printers a Set Printer Port Ports Baud Rate Byte Size 9 Stop Bits 1 y Protocol Press F1 for help lt lt Back B Cancel C e Inthe system of Windows 98 Me click Yes in pop up dialog box and restart the PC 4 8 2 Advanced installation Super installation is mainly used for the users who have special request to the printer driver lt adds the
5. 4 6 Assembling and feeding paper roll Before starting to load the paper roll make sure the specification of paper roll is conformity with printer requirements refer to 2 2 Paper specification 4 6 1 Assembling paper gt Lift up the spanner according to the label arrow and turn over the paper holder side board shown as below _ Spanner Fig 4 6 1 Turning the paper roll holder side board 37 SNC BK T080 user MANUAL gt Shown as in Fig 4 6 2 load the paper roll onto the core shaft and push it to the inner side of this core shaft then remove the paper roll holder side board to its previous position Fig 4 6 2 Load paper roll i Notice Make sure that the paper roll with the thermal layer upward Avoid hurting your fingers while loading paper 4 6 2 Loading paper Before loading paper please confirming the front end of the paper meets with the requirements see figure 4 6 3 Fig 4 6 3 Paper required 38 e Semi automatic paper load Turn on the power and the buzzer sounds for paper end gt Shown as in Fig 4 6 4 let the paper head around the buffer shaft and put it on the incline outside of paper inlet then press the paper head and push it into the paper inlet slightly according to the arrow for certain distance When the platen starts to turn and hold the paper release your hand Thermal side of paper e fering Paper inlet shaft Fig 4 6 4
6. CODE39 CODE93 CODABAR PDF417 12 SN3IC BK T080 user MANUAL Parameter items Parameter i O 203dpi model 300dpi model Standard ASCII compressed ASCII Fonts Optional Asian character set Simplified Chinese traditional Chinese Japanese Korea All fonts can be enlarged 1 to 6 times vertical and horizontal respectively Rotation Print 0 90 Fonts Process o o 180 270 Bold white black reverse underline Support BMP bit image download to RAM Graphics FLASH and direct BMP print Paper type Continuous paper marked paper Paper roll OD Max 254mm Medium Graphics Paper roll ID 225 4mm Thickness 60 100 um Thermal layer Outer side inside 24V power supply room temperature 2 5A 50 average value Paper out detection Optical sensor Paper out speed 400 mm s Retraction detect Optical sensor Paper retracting 400 mm s speed PRESENTER Retraction Ejection holding close high speed presenting optional Paper out modes Note holding paper or presenting paper at high speed is customized 2100 Km Reliability Print head lifetime 313 SN3IC BK T080 user MANUAL 203dpi model 300dpi model Cutter lifetime 21 000 000 cuts 65um thermal paper MTBF 37 000 000 lines Feed paper Operation Temperature 5 45 C i environment Humidity 20 90 RH 40 C Environment Temperature 40 60 C Storage envi
7. hHorizontal paper holder 2 Paper roll shaft 3 Paper near end sensor 4 Keypad 5 Circuit board box 6 Power switch 7 Mechanism 8 Product label 9 PRESENTER 10 Paper feed label 11 Buffer shaft 12 Bottom plate 13 Spanner 14 Spanner label 19 SN3IC BK T080 user MANUAL Note This manual introduces the exterior of the printer with standard horizontal holder of which the control board is put on the right feed paper on the left 20 SN3IC BK T080 user MANUAL 3 2 External dimension 3 2 1 Overall size of the printer Paper outlet Figure3 2 1 Print size with standard horizontal paper holder Load paper on the left 21 BK T080 user MANUAL Fig 3 2 2 The printer size compatible with BK W080 horizontal paper holder 22 Paper outlet 370 8 313 20 9 gt 260 7 302 6 16 5 126 5 Fig 3 2 3 Printer size compatible with BK W080 vertical paper holder 23 SNIC BK T080 user MANUAL 3 2 2 Printing unit size The printing unit means the part with paper holder and circuit board box Its dimension is shown as below Fig 3 2 4 Print unit size Printing unit size
8. 115200 C Half cut A X Cancel 90 SNIC BK T080 user MANUAL Appendix 2 2 Demo program The Demo program software is KIOSK Application and it is mainly used to demonstrate the typical functions of the printer for users reference in using the printer It supports the following system platforms Windows2000 Windows XP Windows Serve 2003 The following is the main interface figure of KIOSK Application For details please refer to the help files in the tool software package 91
9. 150 L X122 W X 110 H mm 24 SN3IC BK T080 user MANUAL 3 3 Print unit and controlling parts The controlling parts include circuit board and corresponding snobs interfaces 3 3 1 Exterior of print unit and controlling parts Print unit consists of printing mechanism and cutting mechanism referred to figure 3 3 Print unit Fig 3 3 1 Print unit and controlling parts 1 Print unit tip board 2 Spanner 3 Auto cutter 4 PRESENTER 5 Power switch 6 Cut button 7 Feed button 8 Reset button 9 Paper LED 10 Error LED 11 Power LED 12 USB interface 13 RS 232 14 Power socket 15 Paper inlet Note Take the left paper feed structure as an example to explain the exterior 25 SN3IC BK T080 user MANUAL 3 3 2 Print unit explanation 1 Spanner After turning over PRESENTER the spanner could be pressed down to separate the platen from the print head so that some errors could be removed Power switch Press 0 to turn off the power or press to turn on the power CUT button Press this button to cut paper under any status even if the printer alarm or not FEED button gt If the printer doesn t alarm press down this button to feed paper gt f need to feed long paper this button could be pressed constantly gt After pressing FEED button and turn on the power for 1s the printer shall start and print a self test page of which the printout could
10. 49 4 8 1 Typical inStallati0N ooo oononinnicinnonncccnnnnoccccnncnncccnnnnnccnnnncarnno 49 4 8 2 Advanced installation oooonmnninincinnnnnnnnnniconccccnnccrnnnananrcncnicnnnns 52 4 8 3 USB printer driVer ooooooonnonicicicicnnncononononccncnncarnnnanann cnc nannnnns 55 ROUTINE MAINTENANCES coooooocccccccconncccnnnnnananancnnnnnnnnns 60 5 1 Cleaning Print head ooooococccccocononoconcncccoccnnnnnncncnnonnnnnnnanncncccnnno 60 5 2 Cleaning SENSOL cccccceceeeeeeeceeeceeeceeeeeeeceneaeeeeeeeeeseeeeeneaeeess 62 5 2 1 Cleaning paper end SENSO coocococccccccccononcncnncncnnnanannnnnnncncnnnns 62 5 2 2 Cleaning paper load SENSOT oooooccccccocccocaccccncnccananaannnonnnncnnnnns 66 5 2 3 Cleaning retraction SENSOT ooococinoccccnnnocccnoncnncncnnannnncncnnancnnono 68 5 2 4 Cleaning paper out SenSoft coooococcccccccccooooncnonncncnnnannanononnnncnnnnns 69 5 3 Cleaning the platen ooooocococconccooooconcccccoccnnnnanoncnnnnnnnnnnnncnccnnnno 71 5 4 Manual resetting Cutter onccccccccnncccnccnnnnnnnnnnnnnnnnnnnnnnnnininnnos 72 5 5 Manual removal of the jammed paper oooonoccccccccccciconananccononin ns 73 5 6 Remove the jammed paper of presenter ooocococcccccccococccccccccccons 74 INTERFACE SIGNAL c000nccccccccconnncccnnnnononnncnnnncnannnnnnnnnnnnnns 75 6 1 IRS2232 Interaction 75 NACI A nnen 75 27 SN3IC BK T080 user MANUAL 6 1 2 Interface linking terminal distribution and signal function 75 6 1 3 Demons
11. e Itis recommended to do routine maintenance per month 5 1 Cleaning Print head When the following cases occur the print head should be cleaned e Printout is not clear e Some columns on the page are not clear e Paper feeds or retracts with big noises Cleaning steps as follows 1 Turn off the printer power 2 Referring Fig 5 1 1 hold the front end of Presenter with hands and pull it forcibly according to the arrow shown in the Fig below so that Presenter could turn to the position as in Fig 5 1 2 60 SN3IC BK T080 user MANUAL Fig 5 1 1 Cleaning the Print head 3 Press the spanner slightly with a finger according to the red arrow shown in Fig 5 1 2 until the platen is away from the cutter unit Fig 5 1 2 Cleaning the Print head 4 Shown as in Fig 5 1 3 now you can view the printer from the downside of the print mechanism and find the Print head in the behind of the moving blade Clean the Print head surface with alcohol cotton which should be twisted 61 before the use Fig 5 1 3 Cleaning the Print head 5 After the Print head is dry execute the assembly according to the reverse steps Then check the connecting cable and start the power after ensuring the correct connection 5 2 Cleaning sensor 5 2 1 Cleaning paper end sensor When the following cases occur the Print head should be cleaned During printing the printer sometimes stops printing and alarms paper end when there i
12. 7 1 and Fig 4 7 2 BK T080 structure space Paper 260 space Button space 310 a Paper outlet Preturning space 1 q p Paper load space r 12 170 Handwheel Paper holder operation space space space Fig 4 7 1 BK T080 space with standard paper holder 41 _Paper outlet Paper load A space 7 i Pre turn space o A Space for Button connecting cable space TA 10 g gt HI m 260 wy pi O Paper lt roll room Waste retraction space Space for connecting or disconnecting cable Paper room Fig 4 7 2 Structure space compatible with BK W080 vertical holder e All spaces explanation lt gt Paper roll space When a complete printer runs normally maximum space should be reserved for the paper roll lt Waste ticket retraction space The space is used for the tickets which shall be taken away Connecting cable space The connection places of communication cable and power 472 cable need spaces lt Button spaces The spaces are used to execute cutter button paper feed button and power switch operation lt gt Paper outlet After the printing the paper should be out and a reception device could be set outside of the paper outlet The paper outlet position sees Figure as below Users can design the corresponding reception device by themselves Paper outlet
13. Browse Search the driver through the browse the default is Setup_BK T080_EN V1 01 USBDRV2 20 then click Next e Click Continue Anyway on the digital signature page e Click Finish to end the installation In the systems of Windows XP and Windows Server 2003 when other USB interfaces of the host is connected to USB printer for the first time pop up a driver installation guide after identifying USB device If the system has been installed USB device driver once according to the steps above select Auto install software in the installation guide then click Next The guide can search the driver automatically A digital signature page shall pop up after finding the device then click Still continue When the installation is finished click Finish to end it Step 2 Printer driver installation Connect one printer to the host and then install the driver Refer to Typical Installation and Advanced Installation 59 SN3IC BK T080 user MANUAL 5 Routine maintenances A Caution Before starting routine maintenance for the printer make sure the power is turned off e Do not touch the surface of print head with hands or metal Do not use forceps so as to prevent print head platen roller and sensors being scratched Do not use organic solvent like gasoline acetone and etc When cleaning print head or sensors please wait for pure alcohol to evaporate totally before starting printing
14. Cutter unit Cross Z screw driver S o 1 x 62 A e 0 a G Fig 5 4 1 Manual cutter reset 5 5 Manual removal of the jammed paper When any of the following errors occurs please remove jammed paper manually Paper jams between platen roller and cutter holder Paper accumulates at paper inlet of the cutter in the front of print head e The cutter can t cut off paper Remove jammed paper in the following steps 1 Turn off the printer power 2 Referring to step 2 to 3 in 5 1 separate the platen from the Print head 273 SN3IC BK T080 user MANUAL 3 Check whether there is wastepaper under the cutter blade and Print head If so please take it out 4 When confirming there is no wastepaper recover the spanner and close the Presenter 5 Turn on the power and press down the CUT button check whether the cutter can operate normally If it can t please refer to 5 4 Cutter manual resetting complete the cutter resetting A Notice e Turn off the power before you remove the jammed paper 5 6 Remove the jammed paper of presenter When any of the following errors occurs please remove the paper manually O paper is jammed into the path of presenter O paper enlace on the platen roller of the presenter O paper does not enter into paper out path of presenter Remove jammed paper in the following steps 1 When uplifting the PRE upper cover along the arrow direction Crefer to Fig 5 2 7 the path of p
15. SNBC has been approved by the following certification ISO 14001 REGISTERED EION RvA CAD DNV Certification B V The Netherlands DNV 1S014001 2004 SN3IC BK T080 user MANUAL Revision History Date Version Description Author 3 30 2007 v1 0 First version Mr Zhang Zhengmin Mr Yang Xiangang SNIC BK T080 user MANUAL Safety Instructions Before installing and using the printer please read the following items carefully 1 Install the printer at a flat and stable place 2 Reserve adequate space around the printer so that the operation and maintenance can be performed conveniently 3 Keep the printer far away from water source 4 Do not use or store the printer in a place exposed to heat of fire moisture and serious pollution and do not expose the printer to direct sunlight strong light and heater 5 Do not place the printer in a place exposed to vibration and impact 6 No dew condensation is allowed with the printer In case of such condensation do not turn on the power until it has completely gone away 7 Connect the AC power adapter to an appropriate grounding socket Avoid sharing one electrical socket with large power motors and other devices that may cause the fluctuation of voltage 8 Disconnect the DC adapter when the printer is deemed to idle for a long time 9 Don t spill water or other electric materials into the printer If this ca
16. be changed with the printer configuration Note Make sure that there is paper in the printer and the print head is not uplifted before starting self test for self test page please refer to Appendix 1 Printer self test page Reset button When pressing down this button the printer shall execute its reset and the print data shall be cleared Paper LED Red When detecting paper end or paper near end paper LED shall light always If the paper is normal paper LED shall not be on Error LED Red Indicate different status of the printer Normally it is not light when errors happen for example paper 26 SN3C BK T080 user MANUAL ena it will flash to give alarms 8 Power LED Green Indicate whether the power is on and it lights all the time when the power is turned on AN Heating lt Print head The Print head are calorific in use please don t touch it just after operation 3 4 Presenter Fig 3 4 1 PRESENTER exterior TT SN3IC BK T080 user MANUAL 1 ZN no Presenter tip board Presenter turnplate Presenter weight shaft This shaft is provided as a part User can decide whether this shaft could be assembled depending on the paper type used The paper details is referred to Table 2 2 Paper specification Paper top cover Paper outlet Paper load sensor When proceeding paper load ensure paper Auto load depending on the position detected by paper load sensor Paper out sensor Check the
17. lt gt If you need paper near end sensor you should prolong the connecting wire of paper near end sensor and pay attention to the position of connection wire do not affect the feeding paper path lt gt Make sure that paper holder has enough intensity and make sure the paper shaft parallel with print head and cutter etc avoid paper twisting in operation e The design of external paper out path In your system it may be necessary to make paper out path matching with the printer To make sure paper out is smooth we suggest that you design your paper out path as follows by different paper out mode 1 When you adopting paper holding or paper backing for paper out 46 SN3IC BK T080 user MANUAL mode please refer to figure 4 7 7 Paper out interface 1 e Note 1 Adopting funnel design for paper out path board refer to the above figure the recommend parameter as follows paper outlet is the benchmark Figure 4 7 7 Paper out interface 1 a lt 2mm notice reserve PRE upper cover turning space b gt 6mm c gt 5mm d lt 1mm 2 When designing paper outlet upper board the bending angle should avoid paper hitting the path the bending board should accord with the direction of the paper or keep 10 obliquity 3 The paper outlet shown in figure is just a sketch map the paper outlet angle can be designed according to actual need But try to avoid the bend angle of paper outlet is not too big in order to increase
18. print paper status to confirm whether the paper is taken away Retraction sensor Check whether the paper is retracted properly in paper retraction tice Do not place the presenter module in a place exposed to direct sunshine Otherwise paper out sensor will become ineffective If paper jammed please open the presenter top cover and remove jammed paper 28 3 5 Paper holder Fig 3 5 1 Paper holder exterior 1 Paper holder supporting board can be turned over for easy paper load 2 Spanner label indicate the force direction when starting the spanner 3 Spanner Through pulling up the spanner the paper holder could be turned aside 4 Paper roll axis Paper near end sensor check whether the test paper roll shall be used out 6 Hand screw connect paper axis onto the paper roll holder 29 SN3C BK T080 user MANUAL 7 Paper roll buffer handle 8 Paper roll buffer shaft The paper entering the print unit could be buffered through this shaft fixed onto the buffer handle 9 Pedestal 3 6 Interface Fig 3 6 1 USB interface printer Fig 3 6 2 Centronics printer 1 Power socket 2 RS 232 interface 3 USB interface 4 Centronics A Notice Can configure only Centronics or USB 30 SN3IC BK T080 user MANUAL 4 Installation and suggestion 4 1 Unpacking Open the carton and check whether all items listed on the packing list are included or have any damag
19. the smoothness of the paper path gt Avoid paper go through too long alleyway and decrease resistance to paper in order to paper out effectively namely 47 Bas BKTOB0 user MANUAL _ the paper can spitting out effectively when the printer spitting the paper Please refer to the figure 4 7 8 Paper out interface 2 j l Upper path b E is Ticket FE oL Lower path Figure 4 7 8 Paper out interface 2 Note Adopting funnel designing for paper outlet board refer to the figure above the parameters are recommended as follows the benchmark is the paper outlet a lt 2mm notice observe PRE upper cover turning space b gt 8mm c gt 10mm d lt 1mm e For the paper go out effectively the path designing should avoid baffling paper going forward and avoid path hitting paper when designing upper path board the bending angle should avoid the 48 SNIC BK T080 user MANUAL paper hitting the path the bending board should accord with the direction of paper or keep 5 obliquity e To avoid the path supporting ticket and the ticket can t fall off the outlet nether board should incline downwards we advise the angle of incline lt the bending angle of paper 10 e When adopting presenter make sure its deepness greater than the longest ticket the recommended deepness is the longest ticket 50mm The above contents is only the reference you can adjust it according to th
20. 0 Appendix 2 2 Demo program ooooocccconononanccocnnnccnnnanannccnnnnnnncnananacnnnns 91 SN3IC BK T080 user MANUAL 1 Summary 1 1 Brief introduction BK T080 printer is a high performance thermal printer equipped with cutter and presenter it can accept up to 254mm paper rolls The maximum print width is 80mm It can be widely used in various Kiosk applications like data communication terminal test instrument terminal and outdoor information consulting terminal etc BK T080 consists of the following modules Thermal printing unit Presenter optional or with paper out path organ Paper holder optional or without Control board Cutter optional or without For different installation environments BK T080 has two modules for customers to select the horizontal and vertical BK T080 can be connected with other device by parallel interface or serial interface and USB interface Drivers are available for WINDOWS98 NT4 0 2000 XP 2003 Windows XP Embedded Note NT operation system doesn t support USB interface SN3C BK T080 user MANUAL 1 2 Main features e Printing gt High speed gt Low noise thermal printing gt High reliability PRESENTER gt Paper accommodation gt Paper retraction gt Holding paper gt Paper out function gt Paper ejection Note gt The Presenter is at the front end of the printer gt Paper ejection and paper out function are not available on standard printer and only for custom
21. Confidential SNBC User Manual BK T080 Kiosk Printer V1 0 SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO LTD SNIC BK T080 user MANUAL DECLARATION This manual applies to BK T080 series embedded printer and the information in this document is subject to change without notice Shandong New Beiyang Info Tech Co Ltd hereinafter referred to as SNBC reserves the right to improve products as new technology components software and firmware If users need the further data about these products please feel free to contact SNBC or our distributors No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of SNBC Copyright This manual was published in 2007 with copyright belonging to SNBC Version 1 0 Trademark Our registered trademark is SN3C Marks means AN Warning Items shall be strictly followed to avoid injury or damage to body and equipment N Notice Items with important information and zts SN3IC BK T080 user MANUAL prompts for operating the printer AN Heating Calorific parts don t touch N Warning Don t touch and avoid damage due to static electricity The quality control system of SNBC has been approved by the following certification ISO 9001 REGISTERED IG MGMT SYS AVA 6074 DNV Certification B V The thE DNV ISO9001 2000 The environmental management system of
22. Semi automatic paper load gt The printer starts to load paper The paper head shall stop at the normal print position until paper load is ended The printer is ready for the print job A Notice e Confirm that the thermal sensitive surface is above see 3 39 E SN3SC BK T080 user MANUAL figure 4 6 4A insure the printer prints correctly When push the paper into the feeding path please energize uniformity confirm the front head of paper paralleled the feeding paper path avoid paper deflecting upwards 4 7 Installing the printer BK T080 embedded printing unit features easy and reliability operation and it has good adaptability of installing and good maintenance Module design active connection embedded character flexible maintenance station please refer to the content of this section in complete printer design to insure BK T080 embedded printing unit can work more credibility and availability 4 7 1 Installation notice 1 Install the printer on a flat and stable place Recommend to use horizontal installation the inclination angle shouldn t exceed 15 paper feeding direction Inclination in other directions is strictly forbidden Keep the printer far away from water source Do not place the printer in the place exposed to vibration and impact 4 7 2 Keep space for printer installation Reserve space sketch Refer to the dimension as below in the design for reserving 40 spaces see Fig 4
23. an installation CD lt gt or floppy disk insert it now What do you want the wizard to do O Click Next to continue e Select Search for the best driver in these location also select Include this location in the search then click Browse Search the driver through the browse the default is Setup_BK T080_EN V1 01 USBDRV2 20 then click Next Found New Hardware Wizard Please choose your search and installation options Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed Search removable media floppy CD ROM Include this location in the search C Setup BK TO80 EN 1 01 USBDRV2 20 v Don t search will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for pour hardware lt Back IL Next gt f Cancel 57 SN3C BK T080 user MANUAL e Click Continue Anyway on the digital signature page Found New Hardware Wizard Please choose your search and installation options E Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed
24. appens that Presenter fails to transmit paper retraction information properly the retraction sensor should be cleaned To clean paper retraction sensor follow the steps given below 1 Turn off the power 2 Shown as in Fig 5 2 9 you can view the retraction sensor at the retraction path of PRESENTER Wipe away the dust and stains on the sensor surface in using cotton swabs twisted dipped with pure alcohol 68 Retraction sensor Fig 5 2 9 Cleaning retraction sensor 3 After waiting for 5 10 minutes until pure alcohol evaporates totally turn on the power 5 2 4 Cleaning paper out sensor When any of the following case occurs paper out sensor should be cleaned e Presenter fails to hold the paper properly After Presenter holds the paper it fails to retract paper To clean paper out sensor follow the steps given below Turn off the power e Shown as in Fig 5 2 7 turn and open PRE top cover 69 SNC BK T080 user MANUAL Retraction sensor OL e Now you can see paper out sensor in the path of PRESENTER Swipe the dust and stains on the sensor surface by cotton swabs dipped with pure alcohol twisted 70 BNE o 35353 BKTOBOuser MANUAL Paper out sensor Fig 5 2 10 Cleaning paper out sensor e After waiting for 5 10 minutes until pure alcohol evaporates totally close PRESENTER upper cover in reverse steps and turn on th
25. assembly mostly depends on the paper specification 2 The ticket width that BK T080 can be suitable for is related with the paper specification greatly as below s Thermal Need weight Suitable for Paper thickness i side shaft or not ticket length 15 SN3SC BK T080 user MANUAL Table 2 2 2 Weight shaft and paper gt Marked paper specification Marked paper should meet the following requirement besides that of standard paper 1 Mark position Y For the marked paper over 79 mm width you can select thermal layer non thermal layer left middle and right six positions as shown in Table 2 2 1 Ensure beside marks cover mark sensor completely The space between mark sensor and the paper midline is 38 2 mm Y For paper mark less than 79 mm width you can select thermal layer non thermal layer middle two positions Ensure the mark midline to stand on the paper midline 2 In using marks it is recommended to use the following parameter v L1 mark width 8mms lt L1 lt paper width v L2 mark width 4mms lt L2 lt 8mm 3 The reflectivity of marks is less than 10 The reflectivity of other part of the ticket within mark width along paper feed direction is over 75 There should not be any characters graphics as advertisement between marks space e Reflectivity Marked part should lied in the back of thermal layer the reflectivity of black mark is less than 15 and other parts reflectivity is more than 75 area between mar
26. cified Position and click Browse button Search the driver through this Browse The default is Setup_BK T080_EN V1 01 USBDRV2 20 then click Next e The guide shows that the device driver name is found then click Next e Click Finish to end the installation Windows 2000 e Connect one USB printer to the host and insert USB connecting line to the idle USB interface of the host The system could find USB device and pop up the driver installation guide Then click Next to enter USB device driver installation Select Search Suitable Device Driver and click Next Select Specific location and click Next Click Browse button and search for the driver through it The default is Setup_ BK T080_EN V1 01 USBDRV2 20 The guide shows that the device driver name is found and click Next e Click Yes on the digital signature page e Click Finish to end the installation Windows XP e Connect one USB printer to the host and insert USB connecting line to the idle USB interface of the host The system could find USB device and pop up the drive installation guide Select Install from a list or specific location and click Next 56 SNIC BK TO8D User MANUAL _ Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for USB Device Driver for POS KIOSK Printers S If your hardware came with
27. e When connecting or disconnecting the cable connector of the AC adapter always hold the connecter shell and don t pull the cable forcibly e Avoid dragging or pulling the cable of AC adapter otherwise the cable may be damaged or broken and a fire and electric shocking may be caused accordingly Avoid placing the power adapter near an overheating device otherwise the surface of cable may melt and cause 35 SN3C BK T080 user MANUAL a fire or electric shock e f leaving the printer idle for a long time please disconnect the power of AC adapter of printer 4 5 Connecting interface cable 1 Make sure that the printer has been shut down sign O in power switch is pressed down 2 Connect the series interface cable parallel interface cable and USB cable into a relevant interface of the printer and fix them with screws or spanner springs see figure 4 5 1 4 6 2 4 7 3 3 Connect the other end of the interface cable to the host computer Fig 4 5 1 Fig 4 5 2 Fig 4 5 3 Serial connection USB cable connection Parallel connection N Notice Make sure the interface cable is connected in correct 36 direction e After connecting interface cable tighten the screws on the both sides of serial interface for parallel interface cable make sure to tighten the spanner springs on both sides e When connect or disconnect the interface cable make sure to hold the plug shell instead of dragging the cable forcibly
28. e actual operation 4 8 Installing printer driver BK T080 printer offers the driver supporting the operation systems as Windows 98 Windows NT4 0 Windows 2000 Windows XP Windows server 2003 The English software package Setup_BK T080_EN V1 01 The installation includes typical mode and super mode 4 8 1 Typical installation Installation steps are shown as below e First run Setup exe in Setup_BK T080_EN V1 01 then read the relative software license protocols If you accept all the clauses click I Accept and Next button 49 SNC BK T080 user MANUAL Jd Install Driver for printers 3 loj xj r Legal Agreement CAREFULLY READ THE FOLLOWING LEGAL AGREEMENT THE SOFTWARE PROVIDED WITH THIS AGREEMENT THE SOFTWARE IS LICENSED AND ITS USE IS SUBJECT TO THE TERMS AND CONDITIONS BELOW IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT PROMPTLY DESTROY THE SOFTWARE AND DOCUMENTATION 1 LICENSE GRANT C Reject e Choose the printer type and name to be installed If you set this Press F1 for Help printer as a default in the system choose the button Set As Default Printer then click Next En Install Driver for Printers Wok r Select Install Module Creet of C Ticket O SY C Label Mm Embedded BKT0802 y F Set As Default Printer Press F1 for help lt lt Back B
29. e power 5 3 Cleaning the platen When any of the following case occurs the platen should be cleaned e Print out is not clear Some columns on the page are not clear Paper feeds or retracts with big noises 71 SN3C BK T080 user MANUAL To cleaning printing platen roller follow the steps given below 1 2 Turn off the power Wait for a few minutes until print head cools down if the printer has just finished printing Refer to the 2 4 steps in 5 1 cleaning print head you can see the platen Wipe off the dust and strains on the platen surface in using cotton cloth dipped with neutrality cleanser should be wrung After the platen roller is dry recover the printer according to the reverse steps and turn on the power 5 4 Manual resetting cutter When one of the following cases occurs should reset cutter unit manually e The cutter can t cut off the paper it doesn t go to home position when pressing CUT button the cutter doesn t act e Paper jams because the cutter doesn t go to home position Press CUT button but cutter doesn t act Tool needed small cross screw driver Reset cutter manually in the following steps 1 Turn off the printer power 2 Use the cross screwdriver to go through the hole as figure 5 4 1 and go forward to the cutter motor turbo rotate the screwdriver along the arrow lightly until there is big gap between upper and 492 nether blade gt
30. es In case of damages or missing items please contact your dealer or the manufacture for assistance Notice Decide whether Presenter weight shaft could be assembled according to the paper type used The details are referred to Table 2 2 Paper specification 4 2 Adjusting paper near end sensor The printer has been assembled completely in the packaging but the paper near end sensor should be adjusted before the printer put into use 4 2 1 Detection range of paper near end sensor The detecting result of remaining paper can be changed with I O and D O of paper roll core shaft The Mini amount of remaining paper can be calculated in theory as below 231 SNC BK T080 user MANUAL Paper thickness Paper roll um VO CA 925 4mm D O B p32mm Mini detecting Max detecting diameter C length diameter C length Mini detecting Mini detecting diameter C length diameter C length p39mm 2 8m p65mm 29 4m Table 4 2 1 Mini estimating amount of remaining paper Fig 4 2 1 Paper roll Paper near end sensor Fig 4 2 2 Mini detection of paper near end sensor 32 SN3IC BK T080 user MANUAL Paper near end sensor Fig 4 2 3 Max detection of paper near end sensor 4 2 2 Adjusting paper near end sensor The default position of paper near end sensor when out of factory is the Mini detection position Referring to Fig 4 2 2 If need the adjustment the method is shown as below Tool cross scr
31. ew driver Paper near end sensor Fig 4 2 4 Adjustment of paper near end sensor 33 SNIC BK T080 user MANUAL gt Turn and loose two M3 screws with a screwdriver shown as Fig 4 2 4 gt Adjust it with a hand according to your requirement see Fig 4 2 4 paper near end sensor adjustment gt When reaching the required detection position tight the screw with the screwdriver AN Notice Mini detecting amount of paper near end as above table is the theory value There is a deviation in actual state 4 3 Connecting the grounding wire To ensure that the printer has a nice grounding status please follow Fig 4 3 1 to connecting the grounding wire Tool needed cross screwdriver gt Tighten the grounding wire to a grounding pole with one M3x5 pan head screw see Fig 4 3 1 then the grounding wire connection is finished Grounding hole Fig 4 3 1 Grounding position 34 SNIC BK T080 user MANUAL 4 4 Connecting the AC power adapter Make sure the printer is turned off 2 With the flat side of cable pin of AC adapter facing downward plug the cable pin into the power interface on the bottom of the printer see Fig 4 4 1 connecting the AC power adapter 3 Connect the AC power cable to an electrical outlet N Notice o Use recommended power adapter or equivalent one Fig 4 4 1 Power adapter connection e Connect power adapter connector at right angle between pin and socket
32. functions which support several USB printers driver and set the driving mode with the steps as below O Run Setup exe in the file Setup_BK T080_EN V1 01 then read the relative software license protocols If you accept all the clauses click I Accept and Next button 52 SNC BK T080 user MANUAL river for Printers Legal Agreement CAREFULLY READ THE FOLLOWING LEGAL AGREEMENT THE SOFTWARE PROVIDED WITH THIS AGREEMENT THE SOFTWARE IS LICENSED AND ITS USE IS SUBJECT TO THE TERMS AND CONDITIONS BELOW IF YOU DO NOT AGREE TO THE TERMS OF THIS GREEMENT PROMPTLY DESTROY THE SOFTWARE AND DOCUMENTATION 1 LICENSE GRANT C Accept Reject Press F1 for help lt lt Back B Next NJ gt gt Cancel C e Choose the printer type and name to be installed take BK T0802 as an example If you want to set the printer as a default choose Set As Default Printer rinters Select Install Module C Receipt Ticket C Label Embedded BK T0802 X F Set As Default Printer Press F1 for help lt lt Back B Cancel C 53 SNIC BK T080 user MANUAL e Choose the installation Advanced and click Next 7 Insta river for Printers Setup Type C Typical Remarks Support multi USB printer Support driver mode selection Press F1 for help lt lt Back B Cancel C e The driver iden
33. ge level When it is used please make sure both the rise and drop time of host computer terminal is not longer than 0 5us 3 When transmitting data the host computer should not ignore the Busy signal or else the print data may be lost 4 The length of parallel interface connection wire should be as short as possible if it meets use requirement 6 2 4 Time sequence of data receiving DATA nStrobe Fig 6 2 1 Time sequence of data receiving Signal time demands O oa moo AICC ew s E C 79 SN3IC BK T080 user MANUAL Table 6 2 3 Explanation about interface signal 6 3 USB interface optional gt RS 232 serial interface is the standard interface of the printer and USB interface is an optional one which accords with USB 1 1 protocol standard and work in full speed mode For interface position please refer to Fig 3 6 1 USB interface configuration model Data transfer bit rate is 12Mbps USB transfers signal and power by a kind of four line cable D and D connection wires in Fig 6 3 are used to send signal Figure 6 3 1 USB Cable 6 4 Power interface This connector is used to connect the printer with external power supply 80 SN3IC BK T080 user MANUAL The pin distribution of power connector FG GND Table 6 4 Power pin definition explanation Figure 6 4 1 power supply 81 SNIC 7 Troubleshooting and maintenance BK T080 user MANUAL If errors occur in the printer consul
34. is the standard interface of the printer IEEE1284 parallel interface is the optional one and works in compatible mode For interface position please refer to figure 3 6 2 Serial interface configuration 76 SN3IC BK T080 user MANUAL 6 2 1 Parameter Data transfer 8 bits parallel Synchronization mode nStrobe signal is provided by exterior Handshake mode Busy signal Signal voltage level TTL compatible Connector 36 pins inner empty type Centronics connector in accord with IEEE1284 agreement 6 2 2 The influence of printer status to parallel interface FAULT pin and PE pin Print head Low Low overheated Upper cover open Low Low Table 6 2 1 FAULT pin and PE pin explanation When above errors occur information can be got by reading the status of correlative pins of parallel interface 6 2 3 Parallel interface signal PinNo source Compatible mode Data 0 Least Significant Bit SN3IC BK T080 user MANUAL a e mgn O C cra 5 O sa ata DCI Sl round TS a oa O stc oa O nata as O o coo Ca sae ota O tro as Sra Ground or Selec nando O aci Buy anar o soa round panoa naci and int CIN AECI IN UN OO VE 78 SN3C BK T080 user MANUAL PinNo source Compatible mode sa Not defined Table 6 3 2 Parallel interface signal definition Note 1 H stands for host computer P stands for printer terminal 2 Parallel interface signal use TTL volta
35. ization Applications gt gt gt Command set is compatible with ESC POS standard Characters handling zoom 1 to 6 times horizontally or vertically rotation print 0 90 180 270 black white reverse underline upside down print Barcode print print barcode by commands in horizon and vertical Character size Font A or Font B can be set by commands e Printer maintenance gt Replace paper roll easily 10 Bas BKTOBO user MANUAL _ gt Clean the print head conveniently Characteristics and parameters can be set by software Auto cut paper Semi auto paper load Mark identification and checkout VV VV V Updating printer firmware on line 11 SN3IC BK T080 user MANUAL 2 Main technical index 2 1 Technical specification Parameter 203dpi model 300dpi model Print method Direct thermal line 82 540 5mm 79 5 0 5 mm 76 0 5mm 69 5 0 5mm 57 5 0 5mm Print width Max 80mm 3 2 Max 80mm 3 2 Max 640 dots Max 944 dots Max 450 mm Print height Min 58 mm Print speed 150 mm s 100 mm s Printing RAM memory SDRAM 2MB Flash memory 1MB 2MB 4MB Print head Thermal resistor temperature detect Print head position Micro switch detect Paper mark detect Optical sensor Paper width Paper near end Optical sensor detect Interface RS 232 Centronics optional USB optional Barcode a F CODE128 ITF UPC A UPC E EAN13 arcode Fonts EAN8
36. ks should not have any figures such as advertisements 16 SN3IC Mark position 1 position 2 A rA a ee sag m Mark sensor position Mark A Ll Fa e F l BK T080 user MANUAL Mark position 3 E ao Paper central line Figure 2 2 1 Marked position Note lt gt Because of paper shaking in the feeding and paper difference the position fixed by mark may have an error of 1mm lt gt To adjust the printer configuration can set the mark length Three sensor positions have been designed in paper path The printer when out of factory is only assembled with one sensor and default position is in the middle of the paper path AN Notice Please use the recommended paper or its equivalents Using other types of paper may affect print quality and reduce the print head lifetime e Do not paste the paper to the shaft core 17 Bas BOBO user MANUAL Ifthe paper comes in contact with chemical or oil it may discolor or be less heat sensitive which will greatly affect the print quality Do not rub the paper surface with a nail or hard metal Otherwise it may discolor When the temperature goes up to 70 degrees paper will discolor So please be careful to the effect of temperature humidity and sunlight in environment 18 3 Structure and functions 3 1 Appearance Fig 3 1 1 BK T080 printer exterior 1
37. nd paper load space The paper load mode used on BK T080 printer is that first one side of paper holder is turned shown as Fig above then recover the paper holder position after loading paper roll on the paper shaft Note According to users requirement the paper holder can be adjusted so that paper holder turns to the left or to the right by changing the configuration in paper load The paper holder can turn to only one side for one user configuration Fig 4 7 5 Paper holder turn to the right Fig 4 7 6 Paper holder turn to the left lt Paper load space Because the paper is required round the buffer shaft in loading paper it is needed that corresponding paper load space should be reserved at the 45 SNIC BK T080 user MANUAL printer side e Notice for paper holder self design It is better to install the printer with its paper holder If the paper holder needs to be designed users should pay attention to the items as below in the design lt gt For installation dimension please refer to 3 2 External dimension lt Keep paper path expedite avoid sharp folder to cause overload lt gt Avoid that paper rubs with sharp object in order to prevent paper thermal layer damaged lt gt Make sure that paper keeps certain pressure to printer elastic shaft to get buffer effect lt gt Make sure that paper center is in consistent with the center of the paper feeding path prevent paper going to one side during printing
38. ng H W ID Printer ID setting Flash Memory Size Printer FLASH capability Flash Logos Size Flash size for bitmap downloading 88 SN3C BK T080 user MANUAL Resolution Printer resolution Valid Print Width Max Maximum print width PrintSpeed MAX Print speed Dark Scale Print darkness Cutter Enable or disable auto cutter Presenter Enable or disable PRESENTER Presenter Mode PRESENTER paper out mode PresenterWaitTime PRESENTER waiting time before retracting or ejecting the printout Comm Interface communication interface setting Rx Buffer Size Data receiving buffer zone size Interface Type Interface type Baud Rate Serial communication baud rate setting Data Bit Serial communication data bit setting Stop Bit Serial communication stop bit setting Parity Serial communication verify bit setting Flow Control Serial communication data stream mode handshaking mode Interface Type2 The second interface type Command CR Enable or disable CR command Resident Fonts Font setting Standard Character Standard character setti
39. ng Compressed Character Compressed character setting Simplified Chinese Asia character setting BarCode Avaliable Printable bar code model 89 SN3IC BK T080 user MANUAL Appendix 2 Tool software For BK T080 printer we provide the following tools EEPROM configuration software and Demo software Their brief introduction is shown as follows Appendix 2 1 EEPROM configuration software EEPROM configuration software is BK T080 EEPROMSet and its main function is to configure the printer It is supported by WINDOWS98 NT4 0 2000 XP Server 2003 The following is the main interface figure of BK TO80 EEPROMSet For detailed use explanation please refer to the help files in the tool software package EEPROM Set V1 0 PaperT ype Long page print Default left margin Continuous Label C Allow C Forbid Port Set CR Mode PRESENTER print C NoAction Feedaline C Forbid C Allow Default right margin Sign Fringe detect Cut and drop back C Front C Behind Forbid Allow USB ID Self feed Paper near end print C Forbid Allow C Allow Forbid Buzzer Paper near end alarm C Forbid C Allow C Forbid C Allow pubes mm s Stop Bits Instruction incept buffer ss es C 4KB C 45B TE Feed wait time Parity 1D 56 Mode suo Ba C FulCut C Part Cut C Odd Baudrate Auto Feed PRESENTER wait time C 9600 C 4800 C No Cut C Cut C 19200 C 2400 Cut type C 38400 C 1200 Default C Full cut Cut position adjust C 57600
40. on the sensor so that you can take off the mark sensor Fig 5 2 6 Cleaning paper end sensor 8 Wipe off the dust or stains on the sensor with soft cotton cloth dipped with pure ethanol After waiting for 5 to 10 minutes until 100 ethanol volatilizes completely finish the assembly according to the reverse steps Then check the connecting cable which should be proper and turn on the power 5 2 2 Cleaning paper load sensor When any of the following case occurs paper load sensor should be cleaned 66 SNC BK T080 user MANUAL e The paper can t back to normal printing position during automatic paper load e Print motor reverse backward for long time during automatic paper load e After printing is finished the paper can t return to normal printing position To clean paper load sensors following the steps given below 1 Turn off the power 2 Force on the direction shown in Fig 5 2 7 until PRE top cover is turned and open 3 Then you can view the paper sensor in PRESENTER path With soft cotton cloth dipped with pure alcohol should be wrung wipe off dust and stains on the sensor surface Fig 5 2 7 Cleaning paper load sensor 67 Paper load sensor Fig 5 2 8 Clean paper load sensor 4 Wait for 5 10 minutes until pure alcohol evaporates totally and close PRE top cover according to the reverse steps then turn on the power 5 2 3 Cleaning retraction sensor When the printer h
41. remove jammed paper Table 7 2 2 Print problems To adjust print darkness contact with our distributors or SNBC If paper jams in cutter please remove the jammed paper first and then press CUT button to reset the cutter 85 SN3IC BK T080 user MANUAL 7 2 3 Problems during paper out Problems Possible reasons How to deal with Paper is end paper Install a new paper roll The printer stops jams in cutter dust Check if there are sundries in printing and warns or wastepaper cutter path clean the paper near errors during printing covers the paper end sensor near end sensor Table 7 2 3 Problems in paper out Note Contaminated paper may cause detection failure 7 2 4 Other problems Problem Possible reasons How to settle The printer is not Connect the printer with the connected with the power correctly LED isn t light and power correctly The Turn on the printer printer doesn t work printer isn t turned on Printer is in error Remove all errors x status The Make sure the communication The printer doesn t T communication cable cable is connected correctly work after receiving is not connected well Print a self test page and set commands i Interface setting is the interface again according wrong to information on it Table 7 2 4 Other problems Note Paper near end alarm acts only as a prompt for users no
42. resenter open completely 2 Take out the jammed paper 74 SNIC BK T080 user MANUAL 6 Interface signal 6 1 RS 232 Interface 6 1 1 Parameter gt data transfer mode asynchronous serial communication gt handshake mode RTS CTS control gt voltage level MARK 3 to 15 V Logic 1 OFF SPACE 3 to 15 V Logic 0 ON baud rate 1200 2400 4800 9600 19200 38400 57600 bps data bit 8 bit or 7 bit parity checkout None even or odd stop bit 1 bit connector 9 pins serial connector negative head Caution Serial baud rate data bit parity bit are set by EEPROM VV VV V 6 1 2 Interface linking terminal distribution and signal function Printer signal and status is described as the following table Signal Signal name direction Output Data output end Output Data terminal is ready 75 SN3IC BK T080 user MANUAL Signal Signal name direction le DSR Data device is ready RTS Output Request to send Table 6 1 1 Interface and pin explanation 6 1 3 Demonstration of interface connection Host side Printer side TXD RXD RXD TXD DSR DTR CTS RTS RTS CTS DTR DSR FG FG SG SG Caution Please make sure the printer is turned on and waiting for the end of initialization then send data to the printer 6 2 IEEE1284 Parallel interface optional RS 232 serial interface
43. ronment o Humidity 20 to 93 RH 40 C With standard horizontal paper holder 431 4 L X 164 4 W X 203 H Compatible with BK W080 vertical paper holder 262 5 L X 190 W X 370 8 H Compatible with BK W080 horizontal paper holder 328 4 L X 147 7 W X 167 H Weight About 4Kg without paper roll Table 2 1 Technical specification Physics Overall size character Note 1 DPI dots printed for each inch One inch is about 25 4mm 2 The real print speed is related with data transmission speed speed darkness print duty control commands and input voltage which may be lower than that in above table 3 PRESENTER is a mechanism accommodating paper and lies at the front of the printer 2 2 Paper Specification Paper type Continuous marked thermal paper 14 SNIC BK T080 user MANUAL e Paper supply method Paper roll Paper width 82 5 0 5mm 79 5 0 5mm 76 0 5mm 69 5 0 5mm 57 5 0 5mm Paper thickness 60um 100um Thermal layer Outer side of the roll Paper roll specification Roll inner diameter 25 4mm or 250mm e Max paper roll outer diameter p 254mm gt Recommended continuous paper TF50KS E2C NIPPON PAPER INDUSTRIES CO LTD F240AC F220 VP MITSUBISHI PAPER MILL CO LTD KFO60 FEAH NEW OJI Paper CO LTD F7ONA FUJI PHOTO FILM CO LTD FV230A1 MITSUBISHI PAPER MILL CO LTD Table 2 2 1 Recommended paper specification Note 1 The weight shaft is a part of BK T080 of which the
44. s paper in fact e The printer doesn t alarm paper end when paper is end e The printer doesn t identify marks correctly Cleaning steps for paper end sensor 62 SN3C BK T080 user MANUAL Turn off the power 2 Screw down one M3 4 screw shown in Fig 5 2 1 with a cross screw driver and dismantle the lines protection board shown in Fig 5 2 1 Fig 5 2 1 Cleaning paper end sensor 3 Screw down two M2 5 4 pan head bolts see item 1 in Fig 5 2 2 with a cross screw driver and dismantle the cover from the print motor shown as in Fig 5 2 2 63 SNC BK T080 user MANUAL Fig 5 2 2 Cleaning paper end sensor 4 Shown as in Fig 5 2 3 hold the Presenter shown in item1 with hands and pull it forcibly according to the arrow shown in the Figure below until the Presenter turns to the position shown in item 2 of the Figure below oa Picture 1 Fig 5 2 3 Cleaning paper end sensor 64 BK T080 user MANUAL Printhead socket Printhead lines Fig 5 2 4 Cleaning paper end sensor Pull out the print line from the Print head socket Screw down four M3 4 screws shown as in Fig 5 2 4 with a cross screw driver then lift up the print module and take it away shown as in Fig 5 2 5 Fig 5 2 5 Clean paper end sensor 65 7 When you turn the spanner according to the red arrow shown in Fig 5 2 6 the mark sensor could be viewed Use a cross screw driver to screw down the M2 screw
45. se happens turn off the power immediately 10 Do not allow the printer to print when there is no paper installed otherwise the print head and platen roller will be damaged 4 SN3C BK T080 user MANUAL 11 To ensure printing quality and products lifetime use recommended paper or its equivalent 12 Turn off the power when connecting or disconnecting interfaces connectors to avoid damages to control board 13 Set the printing darkness in a lower grade as long as the print quality is acceptable This will help to keep the print head durable 14 Do not disassemble the printer without permission of a technician even for repairing purpose 15 Keep this manual carefully for reference SN3IC BK T080 user MANUAL CONTENT E A A A 9 1 1 Brief introduction tddi 9 1 2 Main features ssiri ipponin eaae na 10 MAIN TECHNICAL INDEX oooooococccccccocoooooooononnonnnnnnnnnnnnnnn 12 2 1 Technical Specification ooooonnnnnocccccnoniccnnncancnccnnnnonnnnannn nono 12 2 2 Paper Specification oooooooocccnncnicnococccccncncononnnnronncononcnnonannnnnnos 14 STRUCTURE AND FUNCTION Sooooococccccccccnononononononnnnnm0 2 19 3 1 APPearanCe osise irreal cia 19 3 2 External dimensi n esiis ona eiae 21 3 2 1 Overall size of the prilter oocooioocccnnncccncocicooccncncconnnnananncnonicannns 21 3 2 2 Printing unit SiZe oooconnoccccnnacccccnnonccncnnanonc nn nnnnnn nr nan nnccnnnnnnnn 24 3 3 Print unit and Controlling Parts
46. t error status Therefore when this alarm is given printing task can still be sent 86 SNIC BK T080 user MANUAL Appendix Appendix 1 Self test page Print self test page in the following steps Turn off printer power then press the FEED button for at least 1 second while turning on the printer The printer will start to print a self test page Take 203DPI USB interface model for an example and the self test paper is shown as follows gt BK T0802 TEST FORM Boot Firmware Main Firmware H W Parameters H W ID FV1 010 FV1 000 BK T0802 U 1 Flash Memory Size 1M bytes Flash Logos Size 64k bytes Resolution 203x203DPI Valid Print Width Max 80mm PrintSpeed MAX 150mm s Dark Scale 80 Cutter Enabled Presenter Enabled Presenter Mode Rectration Presenter Wait Time 3s Comm Interface 87 SNIC Rx Buffer Size Interface Type Baud Rate Data Bit Stop Bit Parity Flow Control Interface Type2 Command CR Resident Fonts Standard Character Compressed Character Simplified Chinese BarCode Avaliable BK T080 user MANUAL 4K bytes RS232 38400bps 8 1 NONE RTS CTS USB_BK T0802_1 Ignore WxH 12X24 9X17 24X24 UPC A UPC E EAN 8 EAN 13 CODE39 CODE93 ITF CODABAR CODE128 Explanation of self test page content Boot Firmware Printer BOOTLOADER version Main Firmware Printer monitor program version H W Parameters Printer parameter setti
47. t covered load by paper head dust and wastepaper covers the paper load sensor Paper end the printer not cover is fully closed Dust or wastepaper covers the paper load sensor BK T080 user MANUAL How to settle Clear wastepaper according to requires remove jammed paper check the front head of paper to confirm that the paper load sensor is covered fully by paper Clean the paper load sensor Replace the paper roll Close Print head Clean the paper load sensor Table 7 2 1 Errors in paper load 84 SNIC 7 2 2 Problems during printing Problems Possible reasons BK T080 user MANUAL How to settle The receipt can t be ejected out smoothly Paper jams Check paper path remove wastepaper and reload paper Printout is not clear Cutter abnormally Printing data is lost and no printing The paper is loaded in wrong direction or its quality is poor print head needs cleaning printing darkness is too low input voltage is too low Paper jams in cutter the cutter is broken The print head does not closed Paper jams Make sure the paper roll is loaded correctly Use recommended paper or its equivalents Clean the print head Adjust print darkness Use the power supply which meets requires Check if there are sundries in cutter path contact with SNBC or your local distributor Close printer cover upper properly
48. t the troubleshooting table below If still can t settle the trouble please contact with SNBC or the distributor 7 1 Common errors and settlement Print head overheated Print head uplifting Paper end Description Temperature of print head is too high Print head is uplifted sensor detects paper end Display mode of error LED Buzzer Recovery If temperature is fallen automatic recovering automatic recovering after put down the print head After reloading paper automatic recovering SN3IC BK T080 user MANUAL Display mode of en error LED Description Recovery Buzzer Cutter Paper jams Remove the error paper or cutter jammed jam can t work paper and normally press CUT key to cut paper Table 7 1 1 Error index Printer acts as follows when errors occur Stop printing Busy signal is available Error LED glitters The buzzer beeps 7 2 Solution for common errors 7 2 1 Problems during paper loading Problem Possible reasons How to settle The width and Replace the paper Paper roll can t be diameter of paper roll loaded into paper holder do not match the printer 83 SNIC Problem The printer can t feed paper automatically The buzzer alarms After automatic paper feeding the paper cant stop in the normal print position Possible reasons Paper head is irregular paper jams The paper sensor is no
49. tifies the current system type then click Next nsta river for Printers gt Select Install OS C Windows 98 Me C Windows NT C Windows 2000 Windows XP C Windows Server 2003 Press F1 for help lt lt Back B Cancel C 54 SNC BK T080 user MANUAL e Set the printer driving mode and print port The system defaults LPT1 as the print port and supports several USB installation then click Finish to end the installation q Install Driver for Printers ma E r Set Printer Port Ports LPTI y LT COM port set LPT3 Baud Rate USB_BK T0802_1 USB_BK T0802_2 USB_BK T0802_3 Byte Size USB_BK T0802_4 Protocol Hardware M Raster Graphic Printing Press F1 for help e eai Cancel C In window 98 Me click Yes in the pop up dialog box to restart the PC 4 8 3 USB printer driver USB printer driver is installed with two steps 1 USB driver device installation 2 Printer driver installation Step 1 USB device driver installation Windows 98 Me e Connect one USB printer to the host and insert USB connecting line to the idle USB interface of the host The system could find USB device and pop up the driver installation guide Then click Next to enter USB device driver installation 55 SN3IC BK T080 user MANUAL e Choose Search Device Latest Drive and click Next e Select Spe
50. tration of interface CONNECTION ooooocconccccccnncancnccnanns 76 6 2 IEEE1284 Parallel interface optional oooonococcnnncccnnnnncccncos 76 6 2 1 Paramete sesimin EREA EEEE ENE EERE ETa 77 6 2 2 The influence of printer status to parallel interface 77 6 2 3 Parallel interface signal oooooocionicccnnoniciccnnnonccccnnnnanccnoncancnnnnnno 77 6 2 4 Time sequence of data receiviNd oooooconociccnnnocccncncanccnnnannss 79 6 3 USB interface optional oooninonococicnccccnconaoncnccnnncnnnnnannoncnnnnos 80 6 4 Power interface ooooooocoocccccccccoccconnnncncnnnncononnnnnoncnncnconinnnnnncncnnn 80 7 TROUBLESHOOTING AND MAINTENANCE 82 7 1 Common errors and settleMent oooooccinonocccccncccccinonanonncononin ns 82 7 2 Solution for COMMON Errors ccceceeeeeeeeeeeeeeeeeeeeeeeeseceeeeeees 83 7 2 1 Problems during paper lOadin9 ooonicccnnonicccnnnnecccconnancnnos 83 7 2 2 Problems during priNtiND oooccnnnnocicnnnnocccccnancccccnanancnnnnnanes 85 7 2 3 Problems during Paper Out ooocooooccccnnncicnnonanccncnnncnncnanannn conan 86 7 2 4 Other problemMS cooooonicocccicnnicononononncncnncnnnanannnnn cc aaia 86 APPENDIX ocu iii 87 Appendix 1 Self test page ooooooococcccccccococooccccccccconcnnonnconononcnnannn nono 87 Appendix 2 Tool software ooooooooccccncicicoconoocccnococconannnnncnnononnnnannnnnnos 90 Appendix 2 1 EEPROM configuration software oooonooiccncnnnnicncccon os 9

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents