STH-03ZB User's Manual (ZigBee HA Profile) Ver. 1.03
Contents
1. If STH 03ZB has still not joined after a few attempts check it is within the operational range of 100m line of sight from the parent device and away from other 2 4GHz devices that might interfere with its operations If STH 03ZB has joined successfully but is showing disconnected status green LED flashes twice every 5 seconds then check parent device is correctly powered on If the parent device is functioning correctly STH 03ZB may be out of range or experiencing interference additional router s may need to be added to ensure good connections STH 03ZB User s Manual 7 6 Removing STH 03ZB from the Parent s Network Requirements Sharp pointed tool a Ensure parent device coordinator gateway or router is powered on see relevant device s manual b Ensure STH 03ZB is powered on see Installing and Replacing Batteries in STH 03ZB section and has already joined the parent s network green LED flash once every 60 seconds c Use a sharp pointed tool to apply 3 quick presses to the link switch on STH 03ZB the red LED will flash rapidly for up to 30 seconds or until successful removal d If STH 03ZB has been successfully removed the green LED should show ready to join status flash once every second Recommendation It is strongly recommended to remove the batteries immediately from STH 03ZB once it has been removed from the parent s network as this will prevent damage and greatly improve2. battery life 7 STH 03ZB LED Status The table below shows the LED status for STH 03ZB STH 03ZB LED Status Green LED 1 flash every second Ready to join ready to join network of parent device coordinator gateway or router Green LED 3 flashes one time Successfully joined joined network of parent device Green LED 1 flash every 60 seconds Normal Operations joined network of parent device and functioning normally Green LED 2 flashes every 5 seconds Disconnected joined network but unable to find any parent device of the network Red LED Rapid Flashing up to 30 seconds to be consistent Removing being removed from the network of the parent device Red LED 1 flash every 15 seconds Low Power low battery power replace batteries immediately Green amp Red LED ON ZigBee Reset reset to factory default remove all ZigBee network linkages STH 03ZB User s Manual 8 8 ZigBee Reset In the case where the parent devices coordinator gateway or router for STH 03ZB are no longer available or have been reset STH 03ZB will need to be reset by applying a 5 second press to the link switch the green amp red LEDs will both come on during the reset then the green LED should show ready to join status flash once every second Recommendation It is strongly recommended to remove the batteries immediately from STH 03ZB once it has been reset as this will pre
3. Ensure STH 03ZB is joined to a parent device see Adding STH 03ZB to the Network section d Use software for reading information from coordinator or gateway device see relevant device s manual to confirm STH 03ZB transmissions are being received at the correct interval STH 03ZB User s Manual 6 e If necessary replace STH 03ZB into mounting cradle see Installing mounting for STH 03ZB section Transmission interval setting has been successfully configured Note Transmission interval is read at power on a power cycle is required to effect interval change 5 Joining STH 03ZB to the Network Requirements Parent device such as coordinator eg WZB 01USBC WZB 02485C gateway eg G07 W WZB 05ET or router eg WZB 01USBR WZB 02485R Sharp pointed tool a Ensure parent device is powered on see relevant device s manual b Power on STH 03ZB see Installing and Replacing Batteries in STH 03ZB section ensuring it is in ready to join status green LED flash once every second c Enable permit join status on parent device see relevant device s manual and check STH 03ZB joined the parent device d If STH 03ZB has successfully joined the parent device the green LED should flash 3 times then once every 60 seconds If STH 03ZB s green LED does not flash once every 60 seconds then it has not successfully joined Repeat above steps until STH 03ZB has joined successfully
4. STH 03ZB User s Manual 1 STH 03ZB User s Manual ZigBee HA Profile Ver 1 03 Copyright 2011 14 Nietzsche Enterprise Co Ltd All rights reserved Nietzsche Enterprise reserves the right to make changes and improvements to its products without notice Contact Information Email service nhr com tw Website www nhr com tw Content 1 Package Content and STH 03ZB Views 2 2 Installing Mounting for STH 03ZB 3 3 Installing and Replacing Batteries in STH 03ZB 4 4 Setting Transmission Interval for STH 03ZB 5 5 Joining STH 03ZB to the Network 6 6 Removing STH 03ZB from the Parent s Network 7 7 STH 03ZB LED Status 7 8 ZigBee Reset 8 9 Product Specifications 8 STH 03ZB User s Manual 2 Congratu
5. lations for choosing a world class digital temperature and humidity sensor using ZigBee wireless transmission technology This manual is designed to help set up and get the most from the sensor in a few short minutes Safety notice Please read and follow the instructions before using this product To prevent electrical shock or fire do not disassemble or expose the unit to liquids of any kind Only use attachments and or accessories specified by the manufacturer 1 Package Content and STH 03ZB Views NHR STH 03ZB digital temperature and humidity sensor Mounting fixtures mounting cradle 2 wall plugs 2 screws 2 x AA batteries If any of the above is missing please contact your supplier Front Bottom Side Back Battery Compartment Transmission Interval Setting Switches Temperature amp Humidity Sensor Status LED Link Switch Product Serial Number amp Unique MAC Address STH 03ZB User s Manual 3 2 Installing Mounting for STH 03ZB Requirements Mounting fixtures Drill with 5mm 0 2 inches drill bit size if using wall plugs or 3 5mm 0 14 inches drill bit size if not using wall plugs Size 1 Phillips screwdriver a Locate STH 03ZB with at least 15cm approx 6 inches spacing on each side except on mounting side avoiding the following sources of interference direct sunlight air ow from vents fans doors windows heaters sources of steam oil vapo
6. r etc b If necessary pre drill mounting holes using mounting cradle for alignment then use appropriate drill bit to drill the holes 5mm approx 0 2 inches if using wall plugs or 3 5mm approx 0 14 inches if not using wall plugs c If necessary insert wall plugs into the 2 holes and use size 1 Phillips screwdriver to fasten the screws securing the mounting cradle Note pay careful attention to the orientation of the mounting cradle d Install and remove STH 03ZB using the following 2 step action to ensure the mounting cradle has been correctly and securely installed and STH 03ZB can be installed and removed Install Remove Initial hardware installation for STH 03ZB has been successfully completed 1 2 1 2 STH 03ZB User s Manual 4 3 Installing and Replacing Batteries in STH 03ZB Requirements 2 x AA batteries a Open the battery compartment using the following two step action b If necessary remove existing batteries c Install 2 x AA batteries into the battery compartment ensuring correct polarity d The status LED on STH 03ZB should start flashing to indicate its current state Green LED Status 1 flash per second Ready to join a parent device 1 flash every 60 seconds Already joined a parent device and functioning normally 2 flashes every 5 seconds Already joined but unable find a parent device in the same network e Replace battery compartment door by fi
7. rst slotting base into STH 03ZB then clicking close the compartment New batteries have been successfully installed Recommendation It is strongly recommended to install batteries into STH 03ZB just before joining to parent device as this will greatly improve battery life Also it is recommended to set the DIP Switch time interval to 5 minutes for longer battery life For proper functioning of STH 03ZB and longer battery life please install alkaline or lithium batteries from reputable suppliers Low battery power is indicated by the red LED flashing once every 15 seconds Replace batteries immediately to prevent potential damage and ensure proper functioning of STH 03ZB 1 2 1 2 STH 03ZB User s Manual 5 4 Setting Transmission Interval for STH 03ZB a If necessary remove the STH 03ZB from mounting cradle see Installing Mounting for STH 03ZB section b Set the transmission interval based on the following DIP switch positions Transmit Interval DIP Switch Setting Transmit Interval DIP Switch Setting 1 Second 1 Minute 5 Seconds 5 Minutes 10 Seconds 10 Minutes 15 Seconds 15 Minutes 20 Seconds 20 Minutes 25 Seconds 25 Minutes 30 Seconds 30 Minutes 35 Seconds 35 Minutes 40 Seconds 40 Minutes 45 Seconds 45 Minutes 50 Seconds 50 Minutes 55 Seconds 55 Minutes 60 Seconds 60 Minutes 65 Seconds 65 Minutes 70 Seconds 70 Minutes 75 Seconds 75 Minutes c
8. vent damage and greatly improve battery life 9 Product Specifications Measuring Element Built in combined temperature and humidity sensor Wireless Protocol Compliant IEEE 802 15 4 ZigBee2007 PRO HA Profile Operating Frequency 2 4GHz ISM band Transmission Range 100m 328ft line of sight RF Output Power 1mW 0dBm Power Supply 3V 2 x AA alkaline batteries Operating Environment 10 C 45 C 14 F 113 F 0 95 RH Power Consumption TX 35mA Sleep 1 3 A Measurement Accuracy Temperature 0 5 C Humidity 5 Network Topology Star Tree Mesh Transmit Interval 1 second to 75 minutes based on DIP switch setting Battery Life gt 1 year 5 minute transmission interval dependent on battery quality Enabling Devices Coordinator WZB 01USBC WZB 02485C Gateway G07 W WZB 05ET Router S05 R WZB 01USBR WZB 02485R Dimensions 92 L x 50 W x 23 H mm Weight 37 6g 1 33oz Excluding batteries Supported Systems Windows NT Win 8 Certifications CE FCC
Download Pdf Manuals
Related Search