USER MANUAL
Contents
1. USER MANUAL VERSION ISSUE DATE P N EZ1105 EZ1305 BARCODE PRINTER USER MANUAL EZ1105 EZ1305 Rev C 2013 07 09 920 013611 02 FCC COMPLIANCE STATEM ENT FOR AMERICAN USERS Thisequipment hasbeen tested and found to comply with the limits fora CLASSA digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense EMS AND EMI COMPLIANCE STATEMENT FOR EUROPEAN USERS This eguipment has been tested and passed with the reguirements relating to electromagnetic compatibility based on the standards EN 55022 2006 A1 2007 IEC 61000 4 2 2001 ED 1 2 The eguipmenthasalso been tested and passed in accordance with the European Standard EN55022 forthe both Radiated and Conducted emissions limits EZ1105 EZ1305 TO WHICH THIS DECLARA TIO N RELA TES ISIN C ONFORMITY WITH THE FOLLOWING STANDARDS IEC 60950 1 2005 Second Edition Am 1 2009 G B9254 2008 Class A GB17625 1 2003 G B4943 1 2011 EN 55022 2006 A1 2007 IEC 61000 42. 6 Install a new ribbon by placing first its right hand side and then its left hand side on the holder atthe back Note 7 When installing the ribbon and empty core please make sure to align them so the lug on the holder Slots into the notch on the ribbon Core Passthe ribbon underthe print head Attach the ribbon to the empty core with the adhesive rip at the end of the ribbon Tum the nbbon feed mechanism to tighten the rnbbon until it has no wrinkles Close the print mechanism making sure that it clic ks into place EZ1105 EZ1305 User Manual 7 2 2 Loading the label roll Open the pnntercoverby pressing the release buttonson both sides of the pnnter housing and lifting the cover Place the label roll on the label supply hub Release the print mechanism and lift it Passthe labels through the paper guides up to the tear off plate Adjust the paper guidesto the label width Close the print mechanism EZ1105 EZ1305 User Manual 8 2 3 Installing the label supply hub A Installing the label supply hub for l cores d B Installing the label supply hub for 1 5 cores EZ1105 EZ1305 User Manual 9 2 4 Connecting the prnter to the host computer 1 Please make sure that the printer is switched off 2 Connectthe powercord to the AC adapterand connect the adapterto the printer 3 Connectthe USB parallel cable to the printer and host computer 4 Switch
3. Driver Wizard connect the printerto the uele ho St com p ute r A port is used to connect a printer to the computer Specify the port that vau are using IF veu are connecting using TCP IP or another port type not listed below create a new port Type Serial Port 8600 8M1 Local Port virtual printer part For LISB virtual printer port For USB IP 192 168 1 7 Standard TCP IP Port 182 168 1 7 LPR Create Port Configure Port Ce Entera printername and Seagull Driver Wizard a SSIQ n the a p p ro p na te Specify Printer Name ng hts Names are used to identify the printer on this computer and on the network Enter a name for this printer Printer name Use this printer as the default printer Specify whether or not you want to share this printer with other network users When sharing you must provide a share name Do not share this printer share name Godex_EZ 1105 Once the installation is Seagull Driver Wizard complete a summary of Completing the Seagull Driver the printer settings is wb d ISp la ye d A new printer will be installed using the following settings Name Godex EZ 1105 Check whetherthe pnnter Share name lt Not Shared settings are comectand d c n M eraut 0 clic k Finish to sta rt Manufacturer Godex copying the driver files Model Godex EZ 1105 Version 7 1 6 M 4 05 20 2009 W a it U ntil CO p ving iS To begin the driver
4. Printer Language EPL G EPL Godex Eltron Printer Language GZPL Godex Zebra 8 Printer Language omare Label design software QLabel IV for EZPL only Driver amp DLL Windows 2000 XP and Vista Bitmap fonts 6 8 10 12 14 18 24 30 16X26 and OCRA amp B Bitma p fonts 90 180 270 rotatable single characters 90 180 270 Resident Fonts rotatable Bitmap fonts 8 times expandable in horizontal and vertical directions Sc alable fonts 90 180 270 rotatable Bitmap fonts 90 180 270 rotatable single characters 90 180 270 rotatable Download Fonts Asian fonts 90 180 270 rotatable and 8 times expandable in honzontal and vertical directions Scalable fonts 90 180 270 rotatable EZ1105 EZ1305 User Manual 1 1 D Barcodes Code 39 Code 93 Code 128 subset A B C UCC EAN 128 K Mart UC C EAN 128 UPC A E add on 2 amp 5 12 of 5 12 of 5 with Shipping codes Bearer Bars EAN 8 13 add on 2 amp 5 Codabar Post NET EAN 128 DUN 14 HIBC MSI 1 Mod 10 Random Weight Telepen FIM China Postal Code RPS 128 and GSI Data Bar PDF417 Data matrix code MaxiCode QR code and Micro QR code CO DEPAGE 437 850 851 852 855 857 860 861 862 863 865 866 869 Code Pages dS WINDOWS 1250 1251 1252 1253 1254 1255 Unicode UTF8 UTF16 ECCE o n UEM downloadable from the software Interfaces USB port default on One Tri color LED Power Green Orange and Red Control P
5. down and remove the three screws marked in the illustration from the printer housing Pull the bottom part of the housing upwardsto remove it as shown in the illustration Hold the motherboard by the back panel and pull it up Then tum it over and place it on the print mechanism face down To remove the motherboard back panel unscrew the earthing screw and the back panel fastening screw Secure the RS232 bracket supplied with the printer on the motherboard using the fastening screw and the earthing screw Plug one end of the connection cable into the module EZ1105 EZ1305 User Manual 16 Remove the two hex crewsonthe left and nght of the RS 232 module serial port Push the RS232 module through the opening of the RS232 bracket supplied Secure the RS 232 module using the hex screws you removed earlier Now plug the otherend of the connection cable into the motherboard socket Retum the motherboard to its original position before the installation Please make sure that the screw holes are not covered by cablesorthe motherboard Replace the bottom part of the printer housing as shown in the illustration Secure the printer housing using the three screws you removed earlier EZ1105 EZ1305 User Manual 17 4 2 Installing the Ethemet module motherboard 4 Motherboard backpanel 6 Hexspacer female Hex spacer male Caution 7 Please make sure that you take precautionst
6. using the three screws you removed earlier Note 7 Once you have finished installing the Ethemet module the command XSET USBETHERNET 1 must be sent to the pnnterto enable the Ethemet module While the Ethemet module is enabled the USB port is disabled To enable it again send the command XSET USBETHERNET O to the printer EZ1105 EZ1305 User Manual 20 5 Maintenance and adjustment 5 1 Cleaning the printhead Dust or dirt on the print head may result in inadequate print quality The printer cover should therefore alwaysbe closed during printing Please also make sure that there is no dust ordirt on the print medium you wish to use to ensure a good print quality and print head performance Here is how you clean the print head l Switch off the printer 2 Openthe printer cover 3 Release the print mechanism and lift it Remove the ribbon To remove any label residue or other dirt from the print head see blue amow please use a soft lint free cloth dipped in alcohol Note 17 The print head should be cleaned once a week Note 27 Please make sure that there are no metal fragments orother ha rd particles on the soft cloth used to clean the print head 5 2 Adjusting the print head pressure If you use a variety of label stocksor ribbon types the print quality may suffer You will then need to adjust the print head pressure Ti NE DES Open the printer cover Remove the ribbon Us
7. 2 2001 ED 1 2 CFR 47 Part 15 WARNING Thisisa Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures IbAClassAMan EEAKRD gt RPM TEEMAT EPA ERE M ol BEE EEA PIN ATH ONT AITAME gt EZ1105 EZ1305 User Manual Safety instructions Please read the following instructions carefully 1 Keep the equipment away from humidity 2 Before you connect the equipment to the power outlet please check the voltage of the power source 3 Make sure the printer is off before plugging the powerconnector into the power jack 4 tisrecommended that you connect the pnnterto a surge protectorto prevent possible transient overvoltage damage 5 Be careful not to get liquid on the equipment to avoid electrical shock 6 Forsafety and warranty reasons ONLY qualified service personnel should open the equipment 7 Donotrepairoradjust energized equipment underany circumstances CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the equivalent type recommended by the manufacturer Dispose of used batteriesaccording to the manufacturer s instructions Only use with powersupply adapter model WDS060240 7A Changesor modifications not expressly approved by the party responsible for compliance could void the usersauthority to operate the equipment Specifications are subject to change without notice EZ1105
8. EZ1305 User Manual 1 BARC ODE PRINIER iiini a a 1 TeV BOX COMEM brinna nonn Oa O O 1 EP CCa UO RET AA eo T MIN 1 Mena CO A A a pa EU 3 1 4 Getting to KNOW your PANE T vaciscidntacchasvseravaivdvnssaccaponnnisdencnsiinanseanstarsaccbarninidaayneaaniaassnyin 4 2 PRINTER SETUP cas casas casaudeceueussevasesauassunsauesaunsancsesuseuedeuaseusaavasavacusasusseusssudssuaesent 6 21 LOA GING ANS MD DO Merennerenea a a 6 227 Loading the label TOlld busniendcisbass irruere mia antico aan vvv lvi Da m ova aeaeubeeiemmaeian 8 2 3 Installing the label supply hub eeeeeeeeeeeeeeennnnnnnnnnnnnnnnnnnnnnnnnnnnnnns 9 2 4 Connecting the printer to the host computer rnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnna 10 2 5 Installing tne AVE ismid ie a eh alatasa iii doge um CON 11 3 OPERA ORPANEE ie ena 13 21 EEE DUO AE advaita ja Si aa 13 2A EED NAI CA TOS AMATI r ama mm m 13 3p elge Cara O e EE 13 LM OT ona illi la 14 Be Dee ON 1 A A c ie 15 A AC C ESO IES openness 16 4 1 Installing the RS 232 module serial port nnnnvvnenevenvvnnnnnnnnnnnnnnanannnnnnnenne 16 4 2 Installing the Ethemet module ssscssccseceeeeeeeeeessssssssssseeeeeeeeeeeeeeeeeessssssssssseaeees 18 5 MAINTENANCE AND ADJ USTMENT ee eere re rr nee 21 5 1 C leaning phnEhed d xnenia eir en aevo ERO aaa VOR eR 21 5 2 Adjusting the print head pressure nnnnnnnnnnnnnnnn
9. anel trol key FEED Power Auto Switching 100 240VAC 50 60Hz Environment QPerstion temperature 41 F to 104 F 5 C to 40 C Storage temperature 4 F to 122 F 20 C to 50 C nas Operation 30 85 non condensing Humidy OPE ge 10 9096 non condensing Approvals Length 10 254 mm Height 6 7 170 mm Width 8 8 224 mm 5 5 lbs 2 5Kg excluding consumables Intemal RS 232 card Ethemet 10 100M bps print server default off disables USB when in use Extemal label roll holderfor 10 250 mm O D label rolls Extemal label rewinder Specifications are subject to change without notice All company and or product names are trademarks and or registered trademarks of their respective owners Minimum print height specification compliance can be dependent on non standard material variables such as label type thickness spacing liner construction etc Godex Is pleased to test non standard materialsfor minimum height printing capability EZ1105 EZ1305 User Manual 2 1 3 Interfaces USB port Connectortype Type B Pin No Function Senal port optional Defa ult Baud rate 9600 no parity 8 data bits 1 stop bit XON XOFF protocol settings and RIS CTS RS232 housing 9 pin to 9 pin DB9sckt BDE89plg V max 500mA TXD RXD N C GND RIS CTS RIS DD N C Computer Pnnter RX TX TR GND D TS TS O ON 0 VI JI uU Ne O ON ADU JI UN HG Note 7 The total current t
10. e a screw driverand gently the adjustment screwsforthe print head to increase or reduce the print head pressure EZ1105 EZ1305 User Manual 21 5 3 Adjusting the print line When the print line is incorectly set the print quality on one sde of the medium may suffer 1 To move the print head in direction A asindicated by the blue arrow tum the adjustment wheel anticloc kwise see amow 1 To move the print head in direction B asindicated by the blue amow tum the adjustment wheel clockwise see arrow 2 EZ1105 EZ1305 User Manual 22 5 4 Tioubleshooting problem se The printer is switched on Checkthe powersupply but the LED does not light Up The LED lightsup red and printing isintemupted The label stock passes through the printerbutno image ispnnted The label stock jams dunng There is no printed image A on some partsof the label There is no printed image A on partofthe labelorthe image isblumed A The printed image is positioned incomectly A labelismissed out dunng The pnnted image Is M blumed Note 7 Checkthe software settings driver settings or command codes Look forthe ermor alert in the table in Section 3 5 Enor alerts Check whetherthe print mechanism is closed correctly Please make sure that the label stock isloaded the right way up and that it is suitable material Choose the correct printer drive
11. el EZ1105 EZ1305 User Manual 13 3 4 Selftest The self test function lets you check whether the printer is functioning no mally The contents of a self test printout are listed below Model amp Version Serial port setup USB port setting Test pattern Number of DRAM installed Image buffer size Number of forms Number of graphics Number of fonts Number of Asian fonts Number of Databases Number of Scalable fonts Free memory size Speed Density Ref Point Print direction Label width Form length Stop position Cutter Label Dispenser Mode Sensor Setting Code Page EZ1105 EZ1305 User Manual EZXXXX VX XXX Serial port 96 N 8 1 int usb sw setting ext USB 1 DRAM installed Image buffer size 1500K 000 FORM S IN MEMORY 000 GRAPHIC S IN MEMORY 000 FONT S IN MEMORY 000 ASIAN FONT S IN MEMORY 000 DATABASE S IN MEMORY 000 TTF S IN MEMORY 2048K BYTES FREE MEMORY 454 H10 AR000 R200 W100 Q100 0 3 EO Option DO OO AD See through Volt 0 8 0 5 0 2 0 6 Code Page 850 14 3 5 Eror alens The table below lists the emor alerts you may see in the event of a problem that prevents nomal functioning of the printer allowing you to identify and conect the problem Fast flashing Slow flashing uon frequenc LED indicator Description Solution Unable to detectthe Run the auto detection function z ules Media aper again 99 emor The ribbon o
12. installation process click Finish complete then finish the Installation Once the driver installation printars and Faxes iscomplete the new printer should appear in the Printers and Faxes t 7 2 db folder up Cut Copy e Godex EZ 1105 E EZ1105 EZ1305 User Manual 12 3 Operator panel 3 1 FEED button When you pressthe FEED button the printermovesthe labelto the defined stop position If you are using continuous labels pressing the FEED button will move label stock until you release the button again If you are using individual labels pressing the FEED button will move only one label If the label doesnot stop at the comect position you need to run the auto detection function on the label stock see Section 3 3 3 2 LED indicators EIE een gni mode The printer is ready for operation The printerhasdetected an error Red flashing See Section 3 5 Enor alerts 3 3 Label size calibration The printer can automatically detect and sore label height That meansthe host computer does not need to transmit the label height to the printer 1 Checkthatthe label stock isloaded comectly 2 Switch off the printer 3 Switch on the printer keeping the FEED button pressed When the LED startsto fla sh red release the FEED button The printer will now measure the label stock and store the label height 4 Once the printer has successfully measured the label stock it will print a self test lab
13. nnnnnnnnnnnnnnnnnnnnaannnnnnnnnnnnnnnnnnt 21 3 31 AGJUSIDO the DEDEIFIG rroa eT a TAT TT TTR 22 94o ubleNo oting rcn a a al ale a rdc AA A eta 23 1 Barcode pnnter 1 1 Box Contents Please check that all of the following items are included with your printer Barcode printer Power cord AC adapter USB cable Label stock Ribbon Empty ribbon core Label supply hub Label guide plates set of 2 Quick reference guide CD with QLabel label software user manual 999999 9 99 1 2 Specifications Model X E105 OHS et Print Method Thermal Transfer Direct Thermal Resolution 203 dpi 8 dot mm 300 dpi 12 dot mm PrintSpeed 4IPS 102 mm s 3 IPS 76 2 mm s Print Width 425 108 mm 4 16 105 7 mm Min 0 16 4 mm Min 0 16 4 mm m engin Max 68 1727 mm Max 30 762 mm Memory AMBFlash 2MB for user storage SMB SDRAM Sensorlype Fixed transmissive sensorand reflective sensor Types Continuous fom gap labels black mark sensing and punched hole label length set by auto sensing or programming Width 1 25 4 mm Min 4 64 118 mm Max Thickness 0 003 0 06 mm Min 0 008 0 20 mm Max Label roll diameter Max 5 127 mm Core diameter 1 1 5 25 4 mm 38 1 mm Types Wax wax resin resin Length 360 110 m Ribbon Width 1 18 Min 4 33 30 mm 110 mm Max Ribbon roll diameter 1 57 40 mm Core diameter 0 5 12 7 mm with notch
14. o prevent electrostatic discharge during the installation Make sure that the printer is switched off and the powercord disconnected from the printer You should work on a clean flat surface Tum the printer upside down and remove the three screws marked in the illustration from the printer housing Pull the bottom part of the housing upwardsto remove it asshown in the illustration Hold the motherboard by the back panel and pull it up Then tum it over and place it on the print mechanism face down To remove the motherboard back panel unscrew the earthing screw and the back panel fastening screw EZ1105 EZ1305 User Manual 18 Secure the motherboard back panel supplied with the printer using the back panelfastening screw and the earthing screw Using the male hex spacer secure the female hex spaceron the motherboard in the position shown Align the Ethemet module with the new motherboard back panelas shown in the illustration Secure the Ethemet module on the motherboard using the fastening Screw Plug one end of the connection cable into the motherboard and the other end into the Ethemet module EZ1105 EZ1305 User Manual 19 10 Align the round opening onthe Ethemet module with the round opening onthe motherboard and retum the motherboard to itsonginal position before the installation Replace the bottom part of the printer housing as shown in the illustration Secure the printer housing
15. o the serial port may not exceed 500 mA EZ1105 EZ1305 User Manual 3 1 4 Getting to know your printer 2 3 5 4 6 1l Release buttonsforopening the printer cover 1 4 3 Ribbon feed mechanism 5 Printmechanism Z o 6 Holderfornbbon rewind core 4 Ribbonviewingwindow Screws for adjusting the print head pressure left right EZ1105 EZ1305 User Manual 4 E z 4 Screw foradjusting the print line 0 0 6 Labelsensor 0 07 4 O Feed slot for continuous labels On off switch Power jack Powerjack 09090900 4 UsBpot Ethemet port optional 6 Serial port RS 232 optional EZ1105 EZ1305 User Manual 5 2 Pinter setup This printer supports the following printing methods e ka ribbon fortransfering a printed image to a medium printing TTP Direct thermal Doesnot require a ribbon only thermal paper printing DTP Please check which printing method you are using and alterthe settingsaccordingly in the printer dnver and or software 2 1 Loading the ribbon Place the printeron a flat surface To open the printer cover pressthe release buttonson both sdesofthe printer housing and lift the cover Installthe nbbon rewind core by placing first its nght hand sde and then its left hand side on the holder Release and lift the pnnt mechanism EZ1105 EZ1305 User Manual
16. on the printer The operator panel should now light up EZ1105 EZ1305 User Manual 10 2 5 Installing the driver Insert the product CD in the CD DVD dnve of the host computerand open the Windows Drivers folderon the CD Selectthe icon forthe driverfile and click it to start the installation Follow the instructions on the screen The Driver Wizard guides you through the installation procedure Select Install printer drivers 5 Specify your printer model EZ1105 EZ1305 User Manual Windows Drivers File Edit View Favorites Tools Help GG 0 pj o6 Back Forward Up Cut Copy Paste Search Address 0 DiWindows Drivers File and Folder Tasks c2 Make a new Falder ES Publish this folder to the Web E3 share this Folder Seagull Driver Wizard Welcome to the Seagull Driver Wizard This wizard helps you install and remove printer drivers What would you like to do CO Upgrade printer drivers Q Remove printer drivers Seagull Driver Wizard Specify Printer Model The manufacturer and model determine which printer driver bo use Specify the model of your printer Printer Model Godex Ez 1100 Plus GEPE Godex EZ 1105 Godex EzZ 1200 Godex EzZ 1200 Plus Godex EzZ 1200 Plus SEPE Godex Ez 1300 Godex EzZ 1300 Plus Godex EZ 1300 Plus SEPE odo ET T30C Seagull 7 1 6 M 4 05 20 2009 wt Browse Source Version 11 6 Specify the port used to Seagull
17. r Choose the correct label stock and a suitable printing mode Clearthe paper jam Remove any label material left on the thermal print head and clean the print head using a soft lint free cloth dipped in alcohol Check whetherany label material or ribbon is suck to the thermal print head Check for emorsin the application software Check whetherthe starting position hasbeen set incomectly Check the nbbon for wnnkles Check the thermal print head for dust or other dirt Use the intemal T command to check whether the thermal print head will carry out a complete print job Check the quality of the print medium Check whetherthere ispaperordust covering the sensor Check whetherthe label stock is suitable Contact your supplier Checkthe paper guide settings Checkthe label height setting Check whetherthere is dust covering the sensor Run the auto detection function 3 3 Automatic detection of label height Checkthe darkness setting Check the thermal print head for dust or dirt See 5 1 Cleaning the print head If any problemsoccurthat are not described here please contact your dealer EZ1105 EZ1305 User Manual 23
18. rlabelsare s Replace the ribbon orlabel roll finished Possible reasons aa a The paperfeed rollerisblocked 9 gt 9 OBERE No gap orblack mark could be detected No ribbon isloaded l To work in thermal transfer mode d Settings but thermal transfer load a ribbon T T enor mode is selected as 2 Altematively select the direct printing mode themal printing mode The memory is full The printer also printsthe Delete data you no longerneed message Memory from the printer memory full Memory mae be a a Use the X4 command to print a 3 pe list of all existing file names Check emor message Filename whether the file name is correct cannot be found File name already exists The printeralso Change the name ofthe file and try printsthe message storing it on the printeragain Filename is repeated Wait forthe printhead to cooldown The pnnt head o Print head temperature istoo to operating temperature The UT enor printer will then switch to standby high mode and the LED will stop fla shing EZ1105 EZ1305 User Manual 4 Accessones 4 1 Installing the RS 232 module serial port 4 RS232bracket ooo Caution 7 Please make sure that you take precautionsto prevent electrostatic discharge during the installation Make sure that the printer is switc hed off and the powercord disconnected from the printer You should work on a clean flat surface Tum the printer upside
Download Pdf Manuals
Related Search