KeContact P20 User manual
Contents
1. KeContact P20 User manual NK f 13 fA Automation by innovation General notes for this manual At various points in this manual you will see notes and precautionary warnings regarding possible hazards The symbols used have the following meanings A DANGER e Indicates that death or serious bodily injury will occur if appropriate precau tionary measures are not taken WARNING A e Indicates that death or serious bodily injury can occur if appropriate precau tionary measures are not taken CAUTION e Indicates that damage to property or minor physical injury can occur if appro priate precautionary measures are not taken gt ATTENTION e Indicates that damage to property can occur if appropriate precautionary measures are not taken e This symbol reminds you of the possible consequences of touching electro statically sensitive components Note Notes on use of equipment and useful practical tips are identified by the Note symbol They do not contain any information that draws attention to potentially dangerous or harmful func tions gt This arrow marks working steps that you are to perform KEBA 2012 2013 Specifications are subject to change due to ongoing technical development No guarantee is offered in respect of any of the specifications given here All rights reserved All intellectual property including trademarks and copyrights are the property of their respective owners Any2. Base model with socket A Status LED B Standard socket variants possible C Housing cover TD 1609 001 b Charging station application example Starting the charging procedure Status LED The charging cable is neither The charging station must be ready for operation the status plugged into to the vehicle nor LED flashes green slowly every 3 seconds Ready for opera the charging station tion Plug the charging cable into The status LED lights up orange briefly Wait for locking the charging station first while the system attempts to mechanically lock the plug After successful locking the status LED flashes slowly green every 3 seconds again gt X Now plug the charging cable The status LED lights up green continuously Ready for into the vehicle charging The charging procedure can be started by the vehicle from this point of time then the status LED flas hes green Charging procedure The charging procedure can also be started in reverse plugging sequence Ending the charging procedure Do not use force to pull out the mechanically locked plug The charging procedure must be interrupted or completed by the plugged in vehicle For details please refer to the instructions of the vehicle manufacturer Disconnect the charging cable from the vehicle Wait for unplugging Disconnect the charging cable from the charging station 10 User manual Version 1 30 Article no 9006
3. of the device User manual Version 1 30 Article no 90061 11 Using the charging station 3 3 Status LED Status LED segments Status LED Flashes ies slowly every 3 seconds blue green Lights up continuously blue reen Flashes H every sec ond blue Lights up orange briefly after plugging in Green LED goes out briefly every 3 seconds 12 KEBA KeContact P20 TD 1609 085 Status LED segments The status LED provides information about the current operating state of the charging station and consists of 4 segments S1 to S4 which can light up together or individually All segments can light up or flash in different colors If not otherwise specified all 4 segments light up together Function Ready for operation charging cable is not yet plugged in on both sides optional The charging station was authorized correctly by key switch or RFID card Authorization is required charging station has not been authorized cor rectly yet authorization with RFID key switch or external enable required Ready for charging charging cable is plugged in on both sides and locked Ready for charging with I8015118 charging cable is plugged in on both sides and locked External enable still required authorization with RFID or key switch car ried out vehicle connected correctly external enable on the enable input still necessary Charging procedure is carried out applies for EN 61851 Mod
4. partner Missing release by external controller energy supplier PV system The charging procedure was not ended cor rectly by the vehicle end the charging proce dure according to the instructions of the vehicle manufacturer Eventually the plug cannot be unlocked under tension Push in the plug and connect it again on the vehicle Then end the charging proce dure again Malfunction first check the possible causes of error for the malfunction Switch off the supply voltage of the charging Station installed or superordinate RCD circuit breaker and line circuit breaker Unplug the charging cable from the charging station Switch on the voltage supply again Defective please contact your service partner Please see our FAQ list on www kecontact com for further information User manual Version 1 30 Article no 90061 KEBA 2012 2013 17 KEBA Troubleshooting KeContact P20 Possible causes of error for malfunction status LED flashes red Malfunctions must always be acknowledged by unplugging the plug and can be triggered for example by the following causes e The plug is not properly inserted locking is not possible gt insert the plug quickly e The plug was unplugged during the charging procedure The plug was not locked correctly unplug the plug and plug in correctly and make sure it interlocks correctly e The plug at the charging station sends an invalid state Hardware
5. unauthorized use thereof is strictly prohibited Document Version 1 30 Article no 90061 KEBA AG Postfach 111 Gewerbepark Urfahr A 4041 Linz KeContact P20 Contents KeContact P20 bears the CE mark The corresponding Declarations of Conformity are located at KEBA AG This product meets the requirements of the ROHS Directive 2011 65 EU The corresponding Declaration of Conformity is located at KEBA AG Disposal information The crossed out trash container symbol indicates that electric appliances and electronic devices including accessories are to be disposed of separately from general household trash You can find more information about this directly on the product in the operating manual or on the packaging The materials are recyclable according to their labeling You can make an important contri bution to protecting our environment by reusing renewing and recycling materials and old NENNEN EC i i dis Revision history Modification Date modified Description from to Pages V1 30 020413 NENNEN Manual revised based on German version 1 30 User manual Version 1 30 Article no 90061 3 OKEBA20122008 SoS KEBA Contents KeContact P20 Contents UMS Vu ee e Ca lo a iy te ecc 5 11 Saey E et 5 lge 00 0 USG RR TEE 6 1 9 SADOULIDIS TIG eoseupduess tap icedeuR e ea E Dnus uR ED EEs 6 Eel mec 7 2 1 TUN RREER
6. 1 KEBA KEBA 2012 2013 KeContact P20 Using the charging station 3 2 Charging station with charging cable Typical version with charging cable A Status LED B Parking bay for charging plug C Housing cover D Hanger for charging cable Storing the charging plug charging cable If no charging procedure is being performed the charging plug can be plugged into the park ing bay B for safe storage The charging cable can be coiled up and placed on the hanger D Note Depending on the design of the charging sta tion the parking bay may deviate from the form TD 1609 041 a shown Charging station application example Starting the charging procedure Status LED The charging cable is not The charging station must be ready for operation the status plugged into the vehicle LED flashes green slowly every 3 seconds Ready for opera tion Plug the charging cable into The status LED lights up green continuously Ready for charg the vehicle ing The charging procedure can be started by the vehicle from this point of time then the status LED flashes green Charging procedure Ending the charging procedure The charging procedure is ended by unplugging the charging cable at the vehicle For details please refer to the instructions of the vehicle manufacturer Disconnect the charging cable from the vehicle Wait for unplugging Le Store the charging cable on the provided hanger
7. EEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEMMEMMMMM 7 22 Optional SQUID EE 8 2 2 1 Ri DS ONSON T Um Tm m 8 222 Key SWIC m 8 2 2 3 Additional optional eoupment nennen 9 3 Usi g the Charging E ecl To a RR ciec seater sne cee cereewecenteresesesensvwesassauveetessensewonstsensesbecentenesmeasataves 10 Sel Ghardibg staton WIS KE EE 10 3 2 Charging station With charging cable EE 11 SECH BR e M 12 Se FRUITION ZAM e ot Lei LEE 13 3 5 Programming RFID user cards optional sssrinin 14 3 6 Installing removing the cylinder lock nnnnnnnannnnnnnnnnennnnssnnnnsnnnnsrnrnnsnnrnssnrersnnennnrrnsnrenrnrernne 15 A MROUBIOSHOOUING E 17 SE A a ET Le 19 GN CEN c 19 o2 Qustomer ServiGO eu cene rtt Etruria eo nuts nbi oneri eden ede exe stade Iu EOE EEEE 19 4 User manual Version 1 30 Article no 90061 KEBA KEBA 2012 2013 KeContact P20 Important information 1 Important information 1 1 Safety instructions WARNING A Not observing the safety instructions can result in risk of death injuries and dam age to the device KEBA AG assumes no liability for claims resulting from this e Electrical hazard The installation commissioning and maintenance of the charging station may only be performed by correctly trained qualified and authorized electricians who are fully responsible for the compliance with existing standards and in stallation regulations For details s
8. ck the troubleshooting measures in the operating manual of the vehicle manufac turer e Make note of model version and serial number type plate on top of the device KEBA KC P20 UC160130 000 C H Pr 89422 N 15112953 B mmer 01 13 W0002 120 240V 120 208V Y 60Hz 30A TD 1609 114 Type plate A Model version B Serial number C Part number User manual Version 1 30 Article no 90061 19 www kecontact com
9. e 3 charg ing procedure Charging procedure is carried out applies for ISO15118 charging proce dure Wait for locking charging cable was plugged in and the system attempts to lock the plug Wait for unplugging charging procedure complete vehicle unplugged User manual Version 1 30 Article no 90061 KEBA 2012 2013 KeContact P20 Flashes orange slowly every 5 seconds Flashes red Segment 1 lights up orange Segment 2 lights up orange Using the charging station Temperature limit exceeded charging procedure temporarily interrupted charging continues after cooling down Malfunction for details see Troubleshooting RFID programming mode RFID cards can be programmed in this mode For details see Programming RFID user cards Commissioning mode the charging station is in commissioning mode 3 4 Authorization optional An optional authorization of a user for charging at the charging station can either occur with a key switch or by means of RFID user cards depending on the de vice version TD 1609 086 Authorization required The status LED flashes blue slowly every 3 seconds Note A successful authorization will be indicated by a series of increasing tones 2 o Authorization successful CS Authorization failed A failed authorization will be indicated by a series of decreasing tones After successful authorization if the charging procedure is not started w
10. eas due to the possible creation of toxic or explosive gases during the charg ing procedure 1 Persons who due to their special training expertise and experience as well as knowledge of current standards are able to assess the work performed and the possible hazards User manual Version 1 30 Article no 90061 5 OKEBA20012200 KEBA Important information KeContact P20 WARNING A e Pullthe charging cable only at the plug and not at the cable out of the connec tor e Ensure that the charging cable is not mechanically damaged bent pinched or run over and the connection area does not come into contact with heat sources dirt or water CAUTION e Risk of damage Never clean the charging station using spray water from a hose high pressure cleaner etc to clean the charging station 1 2 Intended use KeContact P20 is a charging station for the indoor and outdoor area at which electrically operated vehicles can be charged e g electric automobiles The charging station is designed for installation on a wall or in a floor mounted column The respective national regulations must be observed with regard to the installation and con nection of the charging station The intended use of the device always includes the compliance with the environmental con ditions for which this device was developed The device was developed manufactured inspected and documented in compliance with the relevant safety standards Ther
11. ee KeContact P20 Installation manual for the specialist e Electrical hazard fire hazard Never use damaged worn or dirty charging plugs e The owner must ensure that the charging station is only ever operated in per fect condition The charging station must be checked regularly for faulty sockets and con nectors and damage to the housing visual inspection A damaged charging station must be switched off immediately and replaced Repair work to the charging station is not permitted and may only be per formed by the manufacturer replacement of the charging station Do not carry out any unauthorized conversion work or modifications to the charging station Do not remove any notices on the device such as safety symbols warning notices rating plates nameplates or cable markings e The charging station does not have its own power switch The RCD circuit breaker and the line circuit breaker of the building installation serve as mains disconnector e Noextension cables are permitted for connecting an electric vehicle to the power supply device for electric vehicles Only electrical vehicles or their chargers may be connected No connection of other loads is permitted electric tools etc e Readthe information and instructions for your vehicle carefully before you charge the vehicle using the charging station Ventilation A number of vehicles require an external ventilation system in the interior ar
12. efore the products do not pose any danger to the health of persons or a risk of damage to other property or equipment under normal circumstances provided that the instructions and safety precautions relating to the intended use are properly observed The instructions contained in this manual must be followed precisely in all circumstances Failure to do so could result in the creation of potential sources of danger or the disabling of safety devices Apart from the safety instructions given in this manual the safety precautions and accident prevention measures appropriate to the situation in question must also be ob served Only electrical vehicles or their chargers may be connected A connection of other loads e g electric tools is not permitted Due to technical or legal restrictions not all variants options are available in all countries 1 3 About this manual This manual is valid for devices of the type KeContact P20 Use of this manual This manual is intended for the following groups of people e End users users of the charging station e Start up technicians Service technicians 6 User manual Version 1 30 Article no 90061 KEBA KEBA 2012 2013 KeContact P20 2 Overview 2 1 Variant overview TD 1609 001 b Charging station application example TD 1609 042 Charging station application example User manual Version 1 30 Article no 90061 KEBA 2012 2013 Overview Base model
13. fault of the cable unplug the plug and plug in correctly if necessary replace the cable e Temperature shut off The permitted temperature in the charging station was exceeded unplug the plug and wait until the charging station has cooled down Reset of an error If during the inserting of the plug or the charging procedure an interrupt occurs the charging station tries to start the charging procedure again max 5 times If the charging procedure can t be started it must be acknowledged by the proper ending of the charging procedure see section Ending the charging procedure or eventually by re booting the charging station On repeated occurrence of errors without any reason please contact customer service 18 User manual Version 1 30 Article no 90061 KEBA KEBA 2012 2013 KeContact P20 Maintenance 5 Maintenance The charging station is essentially maintenance free but it must be checked regularly by the owner for faulty sockets and charging plug including the charging cable and damage to the housing 5 1 Cleaning gt If necessary clean the housing of the charging station using a moist cloth Stubborn dirt can be removed using a mild solvent free non scouring cleaning agent 5 2 Customer service For questions or problems please contact the executive electrical installation company Before contacting customer service e Check the troubleshooting measures in the Troubleshooting chapter e Che
14. istances are noticeably overcome Turn the key further until it is located in the vertical position The cylinder lock can now be unlocked from the holder using slightly increased force and removed User manual Version 1 30 Article no 90061 KEBA 2012 2013 KeContact P20 4 Troubleshooting PROBLEM Status LED does not light up Charging procedure is not started Vehicle is not fully charged Increased charging time Standard plug cannot be unplugged Status LED flashes red Troubleshooting Possible cause remedy No voltage supply Check RCD circuit breaker and line circuit breaker and switch on if necessary Defective please contact your service partner The plug is not inserted correctly Pull out the plug and insert the plug again The charging procedure was not performed correctly follow the instructions in Chapter Starting ending the charging procedure The plug may possibly be dirty in the locking area or damaged clean the plug or have it re placed The vehicle does not need any power or has an error check the vehicle The vehicle is programmed to a later start time for charging Power reduction due high temperature by vehi cle or charging station Protect the vehicle and charging station from direct sunlight during the charging process carport garage Visual inspection of the connectors for dirt wear or damages If necessary please contact your service
15. ithin 60 seconds the automatic enable expires User manual Version 1 30 Article no 90061 13 KEBA 2012 2013 KEBA Using the charging station KeContact P20 3 5 Programming RFID user cards optional The authorization by an RFID master card is necessary for the programming The ONR programming mode can be activated and deactivated with the RFID master card which is programmed during commissioning of the charging station Activating programming mode Hold the RFID master card in front of the RFID sensor and wait for the signal tone Programming RFID user cards Hold the new RFID user card in front of the RFID sensor within 5 seconds and wait for the signal tone End programming mode To confirm hold the RFID master card in front of the RFID sensor again within 5 seconds and wait for the signal tone The RFID user card is now programmed Deleting RFID user cards The deletion of all stored RFID user cards is only possible by opening the device see Instal lation manual 14 User manual Version 1 30 Article no 90061 KEBA KEBA 2012 2013 KeContact P20 Using the charging station 3 6 Installing removing the cylinder lock Cylinder lock with key TD 1609 080 Preparing the cylinder lock Adjusting the lock nose User manual Version 1 30 Article no 90061 KEBA 2012 2013 General Device versions with a key switch are standard fitted with a cylinder loc
16. k If needed the cylinder lock can be replaced according to the following instructions Requirements The cylinder lock must fulfill the following re quirements e Profile half cylinder according to EN 1303 or DIN 18252 e Dimension A 30 mm for A 31 mm a min imal overhang occurs on the housing e Adjustable lock nose Preparing the cylinder lock gt Adjust the angle of the lock nose S so that it faces up vertically when the key is in the removal position Adjusting the lock nose gt The adjustment of the lock nose angle normally occurs as follows Use a thin object to press in the code pin and push the lock nose into the desired position 15 KEBA Using the charging station TD 1609 081 Inserting the cylinder lock D 1609 082 Engaging the cylinder lock Removing the cylinder lock D 1609 08 Removing the cylinder lock 16 KEB KeContact P20 Inserting the cylinder lock Turn the key 180 so that the lock nose faces downwards Use light pressure to press the cylinder lock into the housing completely until it audibly engages The cylinder lock should be flush with the surface of the housing Engaging the cylinder lock Turn the key to the right until the resistances are noticeably overcome and the key can be removed Do not turn the key past the MAX position The key switch is now ready for use Removing the cylinder lock Turn the key to the left until the res
17. with socket Type 2 A B C Status LED Standard socket variants possible Housing cover Base model with charging cable Type 2 otatus LED Parking bay for charging plug Housing cover Hanger for charging cable 7 KEBA Overview KeContact P20 Base model with charging cable Type 1 A Status LED B Parking bay for charging plug C Housing cover D Hanger for charging cable TD 1609 041 a Charging station application example 2 2 Optional equipment 2 2 1 RFID sensor RFID sensor The RFID sensor R is used for touchless au thorization of a user with MIFARE cards or tags according to 18014443 D 1609 043 a RFID sensor 2 2 2 Key switch Key switch The key switch S is used for authorizing a user Key switch 8 User manual Version 1 30 Article no 90061 KEBA KEBA 2012 2013 KeContact P20 Overview 2 2 3 Additional optional equipment e Network capability e Switch contact for control of external additional equipment e g fan e Enable input for e g ripple control receivers time switches This permits a scheduled time controlled charging of the vehicle to be realized e PLC Power Line Communication according to GreenPhy standard e Mounting column User manual Version 1 30 Article no 90061 9 OKEBA20012200 KEBA Using the charging station KeContact P20 3 Using the charging station 3 1 Charging station with socket
Download Pdf Manuals
Related Search