User Manual BT
Contents
1. As the connection recovered both the indicators of the scanner and the receiver lit RED the scanner is ready to perform scan process 14 Recapture Mode In Recapture Mode scanner performs scan process immediately as the scan trigger is pressed All the scanned barcode data are transmitted to the computer and saved in the buffer of the scanner as well When the scanner is failed to link with the receiver the scanned data will be saved to the buffer of the scanner as well The LED and audio indicators will notice that the scanner is off line As the connection recovered both the indicators of the scanner and the receiver lit RED press the scan trigger and the scanned barcode data scanned during the off line state will recover and send to the computer To transmit the saved barcode data aim the scanner at the data transmission function barcode below and press scan trigger to start All the saved barcode data will be transmitted to the computer Data Transmission Function Barcode Note Delete the saved Barcode Data The scanned barcode data will be saved in buffer memory even after the data transmission is performed by using Data Transmission Function Barcode To delete the barcode data saved in the scanner aim the scanner at the Data Purge Function Barcode and press scan trigger to start delete process Data Purge Function Barcode S Configuring Your Scanner The BT scanner configuration utility provide user with2. Select and click the icon to access the functions 2 Character Case click to select the character case desired 3 Buzzer Setup move the arrows to adjust the buzzer pitch or duration 4 Click Accept to complete the selection Note e The status of Caps Lock and Shift Key in the physical keyboard computer may reverse the setting of the Upper Case Lower Case Universal Conversion while scanning the barcode Do Not press the Caps Lock or Shift key while operating scanner e Select Default to discard all the setting and restore to the factory preset 26 Terminator The function allows user to define the prompt character at the end of each scanned barcode data Blue Tooth Scanner Setting Application EEK Re smm Terminator Operational Mode C NONE CR Keyboard Language C SPACE C TAB ESE C CTRL C General Farameter EXEC Terminator Preamble amp Postamble 1 Select and click the icon to access the function 2 Select the prompt character desired default CR Enter 3 Click Accept to complete the selection Note Select Default to discard all the setting and restore to the factory preset 27 Preamble 84 Postamble The function allows user to define the preamble string or postamble string and add to the scanned barcode data Blue Tooth Scanner Setting Application Preamble amp Postamble Operational Mode Preamble Setting a ep a NEZ ae a a Keyboa
3. according to the applications and task reguired Please refer to Operation Mode page 13 for further information Blne Tooth Scanner Setting Application Operational Mode Operational Mode C Online Keyboard Language LL Barcode C Recapture e E om General Parameter l i Preamble amp Postam Transmit 1 Select and click the icon to access the function 2 Click the mode required Online Batch Recapture 3 Click Accept to complete the selection Note To restore the factory preset select Default to discard the setting All the settings will restore to the factory default and ready for transmitting to the scanner Perform transmit to complete the default setting 293 Keyboard Language The function allows user to enable the scanner be compatible with the computer keyboard layout the language support may vary according to the language version of operating system in the computer For some of barcode may have advanced characters in it and can be read by scanner with the keyboard layout with ALT Mode Please refer to the technical support of the computer provider for keyboard language layout Blue Tooth Scanner Setting Application Setting M Language for Keyboard Interface 0000 I Default Transmit 1 Select and click the icon to access the function 2 Select the keyboard interface US ALT Mode 3 Click Accept to complete
4. 0 mm 90 5 mm 60 0 mm Getting Started Charging the Battery Its recommended to have the battery fully charged before using your wireless barcode scanner You can charge the battery via the supplied recharge communication cradle Charge the battery via USB Interface of Computer Recharge Communication Cradle 1 Turn on the computer 2 Connect the cradle to the USB port on the computer The Communication Status Indicator flashes RED and ready for battery recharge 3 Install the barcode scanner to the recharge communication cradle The LED indicator of the scanner flashes GREEN to indicate the battery is recharging automatically 4 As the battery is fully charged the LED indicator lit GREEN steadily to indicate the battery charge is fully charged 5 Remove the barcode scanner from the cradle The barcode scanner is ready to use Warning e Use only the supplied cradle to charge the battery e DO NOT dissemble or modify the barcode scanner and the pre installed rechargeable battery It should cause damage to the product and the injury to the people near the product 10 Establishing the Wireless Connection between Scanner and Receiver Recharge Communication Cradle The paring between BT 650 scanner and the data receiver Bluetooth 1 1 communication cradle is pre configured in factory User can establish communication automatically when the recharge communication cradle is installed to host PC and the s
5. easy configurations of barcode settings function settings and operating modes according to user reguirement Utility installation 1 Please browse the CD and select folder Utility Catalog Manual 2 Move the cursor to the folder BT Scanner and double click to access the sub folders ramet ECF 100 BCP 1100 a BCP 2200 g BCF 5000 J BCP 6000 O BCP 7000 BCF 8000 EME BT 100 ra O O O MiRAMMSRAaTMSR POC AMPDC AS PDC a SLR AG 3 Select and double click the folder BT Scanner Utility 380584505 388084550 655 V1 20 to access the utility files ET Scanner 1 Utility 656 650 660 670 2 00 CJ BT scanner Utility_56004 400 F Utility 300544505 200044550 6 CP210x Driver EBIDry Driver 4 Click Setup to start installation Nm m WinRAR EEA ta tE oep Bootstrap for Visual Basic set Sa EB n pe Microsoft Corporation 5 Click OK to proceed 2 BT Scanner Setup es Welcome to the BT Scanner installation program ia setup cannot install evetem files or update shared files if they are in use Before proceeding we recommend that vou close any applications you may be TUNE Exit setup 17 Click the button to start installation Note To change the directory click Change Directory to assign the directory desired BT Scanner Setup Begin the installation by clicking the button below Click this button to install BT Scanner software to
6. the specified destination directory Directory C Program Files B TScanner Change Directory Exit Setup Setup will add group BT Scanner to the group box Click Continue to proceed BT Scanner Choose Program Group Setup will add items to the group shown m the Program Group box You can enter a new group name or select one from the Existing Groups list 18 8 Wait for several seconds while the installation is processing eA BT Scanner Setup Destination File CAW INDO Wieysten fay exthfenu oce 9 BT Scanner Setup BT Scanner Setup was completed successfully A 19 Scanner Configuration 1 Initiate the program BT Scanner in your computer fgg ET Scammer e BT Scanner 2 Select the Interface USB Keyboard and click OK button to continue m Interface Selection Interface f Keyboard A5 232 Ver 1 20 Warning Performing the scanner configuration and then transmit the settings to the scanner will clear the entire bar code data buffer Please make sure the barcode data in the scanner are read before configuration 20 File There are selections to manage the configuration parameter files Users can save or load the configuration parameter files according to the applications required Blue Tooth Scanner Setting Application E Default Default this function allows user to restore the scanner to the factory pre
7. BT 650 Series Wireless Bluetooth Barcode Scanner BT 650 M BT 650 N BT 650 C Ver 1 0 Copyright Fametech Inc TYSSO 2012 Contents GONE Sand dan au o ad hu ca 1 SITU OGUIG WON sean coo 3 PCAN ze geste E 3 S PECIA CAL OS hate esate se ae O O O O as hd eet 4 A uzidaso naneste A ad taeesianiweeneee 5 1 AA 6 Salei PRECAUMON este eed cee notes a oby 6 Product Descapotable 7 Getting Started nao oa 9 Charging the Bale said kel a eas deduces 9 Establishing the Wireless Connection 11 Operating Your Scanner eeoeeeeo eee anno 12 A SES Meena o ano V Oo ob OLO oo Garon ace 12 Operation Mode ted v soodkaka a ieee hee 13 Configuring Your Scanner eeeoeeee eee een anne 15 ONV MISTA AOR zoo Ea do honda bn o ka db noo oto 16 Scanner COMMQUFAN OM zes aetvacce o a Bebe 20 Bi CAR O P O OA 21 A 22 A ee ESE an 32 NO O 34 SCAN ZONC usara 34 EIA AA o A 35 Introduction The BT 650 series handheld barcode scanner is designate for long distance data scan applications Incorporating Bluetooth wireless technology BT 650 scanner offers the users up to 50 meters of transmission range from the receiver recharge communication cradle Even the radio link breaks the Bluetooth radio link can still attempt to connect with the receiver With the highly sensitive scan module BT 650 can capture barcodes easily even the barcodes are in poor condition This feature ensures BT 650 capabl
8. canner is activated Connect to PC USB Port Recharge Communicati on Cradle 1 Turn on the computer 2 Connect the Cable to the data collector 3 Connect the USB connector to the USB port on the computer The Communication Status Indicator flashes RED to indicate that the receiver is functioning device searching mode 4 Press and keep hold the Scan Trigger for over 5 seconds to initiate the link to the receiver The LED indicator of the scanner may blink RED and connect to the receiver 5 When the connection is properly established both the LED Indicators of receiver recharge communication cradle and scanner lit RED steadily and the scanner is ready to use 11 Operating Your Scanner Perform Scan To perform the scan point the scanner to the barcode and press the scan trigger the visible red light for easy alignment will guide you to scan the barcode Scan Trigger ScanZone Scanner Red Light alignment Point the scanner with the RED Light alignment projected horizontally to the barcode Adjust the distance to capture the barcode and the beep sound will notice you that the data is N properly scanned Scan Distance Note e Please properly adjust the distance between the barcode scanner and the barcode in order to acquire the barcode data please refer to appendix Scan Zone for further information e Keep the scanner and the receiver in an open space The transmission rang
9. cator i 1 beep sound The LED indicator lit GREEN with as scan trigger 1 beep sound to notice that the pressed data purge is start The LED indicator blinks GREEN oy o beep sound with 5 beep sound to notice that Blink GREEN the data is deleted 37 Recharge Communication Cradle Bluetooth Pairing Indicator Status Indicator Gradle Bluetooth Pairing Status Description Indicator Indicator W The Recharge Communication Cradle is pairing with the Scanner It is pre configured in factory and Blink Green need not pairing in general The scanner is in recharge mode The LED blinks RED Nae continuously while battery is 0 recharging The wireless communication Blink RED between cradle and scanner is establishing it should be established within 2 3 second The wireless communication between cradle and scanner is established and ready for use 38
10. cessories specified by manufacturer Use of anything other than supplied or approved accessories will void the warranty may cause malfunction and and may put the User or other person at risk of injury DO NOT aim the product at eyes of people or animals Some product models use a LASER as a scanning aid may cause serious eye injury Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Unplug this apparatus during lightning storms or when unused for long periods of time The Service is performed by qualified service personnel only Servicing is required when the product and or the accessories have been damaged in any way such as power cable or plug is damaged liquid has been spilled or objects have fallen into the product the product has been exposed to rain or moisture does not operate normally or has been dropped DO NOT dissemble or modify the product accessories and the components i e the pre installed rechargeable battery It should cause damage to the product and injury to people and the warranty is terminated Product Description Scanner Unit LED Indicator Audio Alarm Scan Window Scan Trigger Pb O N 141 2 mm 167 5 mm Recharge Communication Cradle 5 Connector for Scanner Unit Recharge and Communication Cradle 6 Communication Status Indicator 7 Bluetooth Pairing Indicator 90 5 mm 70
11. e may vary due to local conditions 12 Operation Mode There are three scan modes supported by the scanner and users can select proper scan mode depending on the requirements You can access BT configuration utility to setup your scan mode refer to Scanner Configuration page 23 The supported scan modes are as follows Batch Mode default In Batch Mode scanner performs scan process and transmits scanned data through receiver immediately as the scan trigger is pressed When the scanner is failed to link with the receiver and the scanned data is unable to transmit to the computer the data will be saved to the buffer of the scanner temporarily the LED indicators blink and audio indicators beep to notice that the scanner is off line As the connection recovered both the indicators of the scanner and the receiver lit RED press the scan trigger and the scanned barcode data scanned during the off line state will recover and send to the computer Note The barcode data in the buffer will be clear as the connection is recovered and sent to the computer 3 On Line Mode In On Line Mode scanner performs scan process and transmits scanned data through receiver only when the scanner connection is in good condition When the scanner is failed to link with the receiver the scanner will not be functional whenever the scan trigger is pressed The LED and audio indicators will notice that the scanner is off line
12. e of fast capture and process demands By adapting exceptional power saving design the BT 650 wireless barcode scanner can operate much longer than ordinary scanners and ensure the high grade reliability Furthermore the user friendly operation and large memory capacity characteristics enable BT 650 be a cost effective yet reliable data scan solution Features e Light weight and easy to operate e Scan Speed 100 scans sec e Integrated recharge communication cradle with Bluetooth class 1 receiver e Wireless Transmission Range up to 50 meters open space e High barcode readability e Multiple operating modes selectable On line Batch Recapture e Various barcode standards support e Large memory capacity up to 15 000 scans EAN 13 barcode e USB HID Interface Specifications BT 650 C General can Rate ensor Type 0 1 mm 4 mil can Patten lt O o D Z O ystem Interface ndicator ransmission Range Max 50m possibly over 70m in open spaces RSS Codes EAN UPC 2 of 5 Codabar Code 39 Code 128 China Postage Code 93 Code 11 MSI Plessy Code 4 ili Windows base 2000 XP Vista Windows 7 5VDC 5 Scanner 5VDC 5 Cradle 120 mA BT 650 M Bluetooth On 70 mA BT 650 N Power Consumption Bluetooth On Operation Mode 110 mA BT 650 M Bluetooth Off 60 mA BT 650 N Bluetooth Off Power Consumption Sleep Mode 0 7 mA Bluetooth Off Battery Type Battery Capacity Recharge Time Battery charge with R
13. echarge Communication Cradle Readable Bar Code U o 5 lt 85 mA Bluetooth On 75 mA Bluetooth Off Recharge Connection 4 others Ss m pial A Material Color Upper Cap Handgrip Compliance Weight 167 5 x 72 x 78 mm Scanner Unit 90 5 x 70 x 60 mm Cradle Ambient Light Operating Temperature 0 C 40 C 0 C 40 C e 20 80 RH 20 80 RH Operating Humidity non condensing non condensing torage Temperature 20 C 65 C 5 95 RH 5 95 RH non condensing non condensing The transmission range may vary due to local conditions The specifications may be changed updated without prior notice Package Standard Package Scanner x 1 Utility CD x 1 Recharge Communication Cradle x 1 Before Use Safety Precaution 1 10 11 12 Read the manual before use and always keep in proper location for references Install in accordance with the instructions Heed all warnings messages and notifications to avoid injury to self or people misuse may cause malfunction or damage to the product Do not operate the product and accessories near water moisture or dusty location it may cause electrical shock injury or fire Do not place or operate the product near any heat sources such as radiators heat registers stoves or other apparatus that produce heat It may expose the product to the danger of Fire and Explosion Clean only with dry cloth Use ONLY supplied or ac
14. er with 3 beeps to notice Blink Green pressed that the scanner is off line 3 beep sound Faq as scan trigger Buffer Memory Full aed LED Indicator 1 1 2 beep sound as scan trigger pressed The memory is full Battery Recharge eno LED Indicator o d C The scanner is in recharge mode Blink Green O The battery is fully charged GREEN rebates hae Battery Low sn LED Indicator i 2 beeps sound Press the scan trigger and there as scan trigger are 2 beeps to notice that the pressed battery is low Scanner Configuration ion LED Indicator BI 7 beep sound Press the scan trigger and the scan trigger indicators RED GREEN 7 Blink GREEN pressed beep notice that the scanner is O initialing the new setting The scanner is ready for operation 2 beep sound 2 beeps 36 Recapture Mode Data Transmission m LED Indicator i 1 beep sound k There is 1 beep sound to notice as scan trigger a that the data transmission is start Blink GREEN pressed kn in Pa E O The LED indicator blinks k e hs RED and GREEN alternatively Blink while the scanner is transmitting RED GREEN data The LED indicator blinks GREEN nr 1 beep sound with 1 beep sound to indicate the Blink GREEN data is successfully transmitted Data Purge Delete the saved Barcode Data seo Description LED Indi
15. he scanner are read before transmitting the configuration file 33 Appendix Scan Zone BT 650 M BT 650 N based on 90 code 39 barcode 40 mils _ 6 55cm 13 mils 3 20cm 10 mils 5 18cm 7 5 mils 4 13cm 5 9 mils 4 12cm 49mils 4 11cm 4 mils 4 10cm 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 55 BT 650 C based on 90 code 39 barcode 40 mils 15 46cm 13 mils 5 24cm 10 mils 3 5 21em 6 mils 4 15cm 5mils 3 12cm 4 mils 4 9cm 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 34 Status Indicator The following table indicates the LED status indicators and audio indicator Scanner Unit Turn On Turn Off Connection Doo LED Indicator i Ascending beep The scanner is turned and the sound communication is establishing POSEEMOS The connection is turned off beep sound On Line Perform Scan Process Scanner LED Indicator eee eo em scanner is ready for operation Press the scan trigger to perform scan process 2 beep sound n as scan trigger The LED indicator blinks GREEN pressed 2 times with 2 beep sound to notice the barcode is properly scanned Blink Green Off Line Scanner Description LED indicator Audio p m The connection between scanner and Recharge Communication Cradle is not established Blink RED As the scan trigger is pressed The LED indicator blinks GREEN togeth
16. plete the selection Blue Tooth Scanner Setting Application i e Preamble amp Postamble Operational Mode Preamble Setting EV E E E a Keyboard Language Postamble Setting jE jin n fi in E n E Click button to set preamble character or postamble character General Farameter Terminator Preamble amp Postamble Note Select Default to discard all the setting and restore to the factory preset 31 Transmit The function allows user to transmit the configured settings to the scanner Perform the function after all the new settings are completed Blue Tooth Scanner Setting Application Keybord USB Keyboard SS SN ky co Transmit settings from USB interface When all the settings are completed 1 Select and click the icon to access the function 2 Click Transmit to start the transmission 3 When the transmission is completed press the Scan Trigger of the scanner to activate the new setting The audio and LED indicators will notice user that the new settings are activated The LED indicator lit RED steadily and the scanner is ready 32 Transmit Data to BT Scanner x Press Scan Trigger Note The new settings of the scanner are functional only when the parameters are transmitted to the scanner successfully Warning Performing the transmission will clear the entire bar code data buffer Please make sure the barcode data saved in t
17. rd Language LL Barcode Postamble Setting a sn e Click button to set preamble character or postamble character General Parameter Terminator Preamble amp Postamble 1 Select and click the icon to access the function 2 Move the cursor to Preamble Setting or Postamble Setting 3 Select the first icon to define the first character of the string Click mouse left button to enter the character 10 characters max E K Click mouse right button to clear 28 4 There is an on screen keyboard for user to input the character by using the mouse Keyboard Interface Ed pelwfefaprirfofrfofrfs s o pos mal se ESOO Tey Tee BGM ee Es IO EI 5 Select the next icon to enter the next character Repeat step 3 to step 5 until all the characters of the string are entered N n nk A n en K FA Click mouse right button to clear N KN KA Click mouse right button to clear Tip Click Right Mouse button to clear the character Sr rr ro E E K Click mouse right button to clear PO EE EE EE Click mouse right button to clear 29 Note Always enter the characters successively or there is a warning message to notice that the string setting is invalid E NNN HC KON IE DEN NESL NEN KEDNE BIScanner Tip To enter the string with empty character enter space and then enter the next character successively 30 6 Click Accept to com
18. set Perform Transmit to transmit default settings to the scanner Open this function allows user to access the configuration parameter file previously saved in order to restore the specified settings of the scanner msr perform Transmit to send the configured settings to scanner Save this function allows user to save all the specified settings of the scanner to a configuration parameter file msr Exit exit the configuration utility 21 Setting The functions of Setting allow user to configure the scanner to the specified settings ideal for the applications and task Blue Tooth Scanner Setting Application Operational Mode Keyboard Language Mt Barcode General Parameter Terminator Preamble amp Postamble Operational Mode Select the Scan Mode for the scanner Keyboard Language user can define the keyboard language layout default US keyboard or advanced ALT Mode layout Barcode the settings of the supported barcodes General Parameter user can select the conversion of the scanned data in upper lower case and the buzzer settings Terminator user can define the prompt character at the end of each scanned barcode data Preamble amp Postamble user can define the preamble or postamble string and add to each barcode data 22 Operational Mode The function of Operational Mode allows user to select the operating modes Online Batch Recapture
19. the selection Note Select Default to discard all the setting and restore the factory preset 24 Barcode The function allows user to configure various types of barcodes User can enable or disable the specified barcode and configure the parameters according to the characteristics of each barcode Blue Tooth Scanner Setting Application SEE UPC A EAN 8 JAN 8 UPC E ISBNASSN Code ID Setting Code 11 Code 93 MSI PLESSEY CODABAR CODE 4 oon a code terieaved 2 of 5 His 9454 matrik 20f5 ChinaPostage Code 128 Code 39 Code 32 Operational Mode jv Enable Enable Full ASCII Verify Strick Keyboard Lanquage F Transmit Start End Character I Transmit Check Character a FT Verify Checksum General Parameter Terminator Preamble amp Postambie Transmit 1 Select and click the icon to access the function 2 Select the barcode type desired and configure the settings 3 Click Accept to complete the selection Note Select Default to discard all the setting and restore to the factory preset J5 General Parameter The function allows user to convert the characters that encoded in barcode to upper or lower case similar to the function key Caps Lock And the pitch and the duration of the audio indicator are adjustable as well G Blue Tooth Scanner Setting Application n General Parameter Buzzer Pitch Buzzer Duration 30 Transmit 1
Download Pdf Manuals
Related Search