[ Installation- & Owners-Manual ]
Contents
1. command The confirmation SMS is not sent at the com mands where there is a different SMS response May 2015 AMPIRE Electronics All rights reserved Reset renewal of factory default setting Command format RESET 4321 RESET The function resets all parameters to factory default setting After the command is sent initialization of the LOC200 will be done and it is necessary to wait at least 2 minutes before the LOC200 is ready to process next commands This function does not affect assigned PIN code 23 May 2015 AMPIRE Electronics All rights reserved Configuration identification User s function Command format CONFIG User s functions of the LOC200 are controlled by commands The LOC200 sends SMS with current configuration as a res sent as an SMS from your mobile phone to the LOC200 tele ponse to CONFIG command phone number Command is always sent together with PIN code which defines authorized user s The PIN code is a four digit number which can be changed The PIN code is set by manufacturer to value 4321 symbols are used instead and GPS alarm are sent IG F of PIN code in the text below The commands can be typed both in regular or capital letters In case the command is not sent in a correct form the LOC200 will send SMS with the text COMMAND ERROR In case the command is sent with incorrectly entered parameters the LOC200 will send SMS with the text key word ERROR2. of remaining wires is optional In case particular wires are not con 1x per secon nected relevant functions of the system will not be active LED blinking slowly MEANE CORRE METE 1x per 3 seconds The output of external alarm can be connected to input of the LOC200 using white or orange cable LED is not blinking The device is switched OFF Green LED indicates GPS LED blinking quickly 1x per second AO white cable INPUT alarm is activated by signal OV A1 orange cable INPUT alarm is activated by signal 12V The device is trying to receive GPS data h l PD Eng Ley The device receives actual GPS data The maximum current carrying capacity of the switching 1x per 3 seconds relay is 12V DC 5A While controlling an appliance with a higher current load use an auxiliary relay with appropriate technical parameters 3 Connect the GPS antenna and the cable connector to the unit GPS antenna must be placed horizontally and must not be obstructed from the top by metal parts LED is not blinking GPS module is switched OFF 4 Switch car ignition ON and OFF The unit is ON now Wait approximately 2 minutes for the unit initialization com pletion The unit is ready to receive configuration SMS commands after that time May 2015 AD4PIRE Electronics All rights reserved May 2015 AMPIRE Electronics All rights reserved 1 YELLOW GPS LOCATOR WY 2y Installation example INPUT A1 12V ORANGE
3. EXTERNAL ia CAR ALARM lane anes OR INPUT A0 OV WHITE GPS locator installation into the vehicle 12V BROWN It is recommended to place the RUE GPS locator for example under ig Remove covers GREEN the dashboard Remove the nec Maal of the dashboard js essary covers of the dash board _ av RED and choose a suitable place for ae GPS locator and backup battery GND C RED WHITE Basic connection of GPS locator can be done via three wires red black and yellow During the E View into the connector m wires connection the cable con Connection of external car alarm nector must be disconnected from the GPS locator The output of external alarm can be connected to input of the GPS locator using white or orange cable e Red wire connect to 12V power fhrea Reas nomai oien NOVa C S Pin 3 Blau Relais normal geschlossen NC 87a supply Power supply must be con rinsweis Externe Alarm Eingang A0 Masse e AO white cable INPUT alarm is activated by signal OV tinuous and must not be interrupted fin torres ee Alarm Eingang A1 12Volt which must be longer than 0 8s even if the vehicle is parked Pin 12 Rote 12V Backup Batterie e A1 orange cable INPUT alarm is activated by signal 12V e Black wire connect to a car frame which must be longer than 0 8s e Yellow wire connect to contact 15 Connect the backup battery gel battery 12V 1 3Ah to black circuit which is powered 12V and red white cable
4. Installation amp Owners Manual Contents Infroductona ji lai ti 5 Installation into the vehicle 1 11 11 11 7 e LOC200 installation into the vehicle 7 Installation example 11 11r rire 10 e GPS locator installation into the vehicle 10 e Connection of external car alarm i 11 lt Configuration iaia ini 13 A e Entering of authorized phone numbers for alarm SMS and controlling of GPS higher level protection mode i 13 x lt e Switch relay configuration at alarm activation 15 e STOP function relay switching 16 one e Setting of time period for sending a current O position information at GPS alarm activation 17 9 e Configuration of SMS text sent at GPS alarm ci activa ON eissaia iaia 18 e e Configuration of SMS text sent at INPUT Rus alarm activation u iii 19 e Setting of alert call in case of alarm activation 20 e Way of sending GPS coordinates in SMS 5 21 e Setting of confirmation message for SMS COMMA GS sicscnssdavincncssntesarnccsttentetasaserencsdetouneanendetedes 22 e Reset renewal of factory default setting 23 Configuration identification ii 24 3 May 2015 AMPIRE Electronics All rights reserved User s TUNCHons ii ia e Thief
5. all SMS commands at least one GPS protection is ON max 40mA STAND BY The device is OFF and does not respond to any SMS commands OmA May 2015 AMPIRE Electronics All rights reserved Backup battery We recommend gel battery 12V 1 3Ah The battery endurance is 30 to 60 hours depending on momentary operating mode of the LOC200 Charging of the backup battery is done automatically while driving yellow wire Functions Construction e Inserting the SIM card via side drawer no need to open the device e LEDs indicating the GSM and GPS status are integrated in the device e The maximum current carrying capacity of the switching relay is 12V DC 5A e Highly improved remote control of integrated switching relay e Possibility to control remotely particular vehicle devices via your mobile phone e g heater remote control e Input for external car alarm with a possibility to use GPS locator also as GSM pager input is activated by signal OV or 12V e Function CALL at alarm activation enables automatic call to preset telephone number better alert in case of alarm activation e Displaying the vehicle current position on the map directly on your mobile phone display this service is without any additional fees completely free of charge e Simplified searching of the vehicle position on internet via portal satmaps net this service is without any additional fees completely free of charge e Possibility to edi
6. coordinates displaying coordinates in the form of a link Relay switching for unlimited time Command format SWITCH n n 0 unswitched relay n 1 switched relay The relay in the LOC200 can be switched using command SWITCH with parameter n so that particular devices in the vehicle can be remotely switched ON or OFF for unlimited time e g alarm sound Relay switching for preset time Command format SWITCH xy X time for which the relay stays switched from 0 to 240 y time unit of the number entered by parameter x May 2015 AIMPIRE Electronics All rights reserved y s seconds y m minutes The relay in the LOC200 can be switched using command SWITCH with parameter xy so that particular devices can be remotely switched ON or OFF for limited time Relay switching for time preset by command RELAY Command format SWITCH In case you enter command SWITCH without any para meters the data preset by command RELAY are automatically accepted Request for remaining credit in pay as you go SIM card used in the LOC200 Command format CREDIT xxxxx xxxxx dialed number for info about remaining credit in the pay as you go SIM card Contact your GSM operator for the information 4321 CREDIT 100 33 May 2015 AMPIRE Electronics All rights reserved The system will respond by message from your operator containing info about current credit in the SIM card This function is applicable
7. www satmaps net free of charge The system consists of a LOC200 unit and a satellite GPS an tenna The LOC200 unit is usually placed in a hidden and a difficult to approach place e g under a car dashboard SIM card of the GSM mobile operator is placed inside the LOC200 unit the LOC200 has its own telephone number It is possible to use a contract or a pay as you go SIM cards In case you decide to use a pay as you go SIM card you can check its remaining credit using your mobile phone Charg ing of the pay as you go SIM card can be done from your mobile phone or for example using ATM check possible op tions for a remote pay as you go SIM card charging with your GSM operator The system will communicate with you using SMS s therefore it is essential to pay attention to rates for SMS services while choosing your mobile operator We recommend you to acti May 2015 AMAP IRE Electronics All rights reserved vate roaming on the SIM card just in case of localization of the vehicle abroad The LOC200 unit connects to a vehicle onboard power 12V DC We recommend you to connect the unit to a backup battery just in case the main power source is stolen or inactivated The LOC200 allows other functions which are described in details in this user s manual May 2015 AD4PIRE Electronics All rights reserved Installation LOC200 installation into the vehicle Pin 1 Brown Pin 2 Green Pin 3 Blue Pin 4 White Pin 5 Yellow P
8. Authorized number GPS alarm is sent G Authorized number INPUT alarm is sent I Relay configuration jy CONFIG PHONE IN 4906021283261G 490777545674G Setting of period for sending ila 4907775456701 i SMS s at GPS alarm RELAY 105 16 Thief protection ls PERIOD T3 N10 Setting of confirmation for pro i l Li is ON GPS i k CONFIRM1 The LOC200 can be used for protection either separately or n Si ig CALL together with external alarm Modes GPS protection and B ee p n 0 GPS higher level protection can be used if the LOC200 is ceo used without car alarm Mode INPUT protection can be sending coordinates in the form used in addition to the two above mentioned modes if exter I GPSS 1 of a link 1 is ON y nal car alarm is connected to the LOC200 Current relay mode 0 relay is unswitched Mode of GPS protection 0 is OFF GPS protection The GPS protection activates alarm if the vehicle starts mov ing while the car ignition is OFF This is protection against Mode of GPS higher level protec towing the car away We recommend to keep this kind of ORSO protection permanently ON This protection does not need 25 May 2015 AIMPIRE Electronics All rights reserved May 2015 AMPIRE Electronics All rights reserved to be deactivated before driving The GPS protection sets GPS alarm activation GPS alarm is activat
9. LAY xy z X time for which the relay stays switched 0 to 240 y time unit of the number entered by parameter x y s seconds y m minutes Z determines under what circumstances the relay will be switched z relay will be switched when INPUT alarm is activated z G relay will be switched when GPS alarm is activated z IG relay will be switched when both INPUT and GPS alarm are activated Default setting 1s IG 4321 RELAY xy z Parameter z is optional If the command RELAY is entered with out paramter z the relay will be switched in both INPUT alarm and GPS alarm activation the value IG is set automatically This command sets the time for which the relay will be May 2015 AMPIRE Electronics All rights reserved switched at alarm activation or while sending the command Setting of time period for sending a current SWITCH without parameter position information at GPS alarm activation Command format PERIOD xy Nz STOP function relay switching xX determines whether next alarm SMS will be sent Command format STOP n after a certain time or distance covered x D Distance after distance covered Km n 1 switches the relay for 240 minutes after the x T Time after a certain time minutes vehicle has stopped n 0immediately sets the relay to a normal contact position y determines the number of kilometers or minutes y 1 to 60 Z determines the number of alarm SMS within one activat
10. correct format with valid PIN code In case you use a pay as you go SIM card make sure that the SIM is still active and that there is enough credit for sending SMS s After the device is switched ON it is necessary to wait for device initialization completion it can last up to 2 minutes before first command can be sent Previous SMS command must be processed before next SMS command can be sent Check the validity of entered authorized tele phone number including a country code by using command CONFIG Verify whether the authorized telephone num ber has CLIP service activated identification of a calling number May 2015 AMPIRE Electronics All rights reserved Problem The device does not activate GPS alarm False GPS alarm Forgotten PIN code of the device Das Ger t antwortet auf SMS Befehle aber nicht auf Anrufe von autorisierten Telefonnummern Solution Check whether appropriate GPS protection was activated GPS 1 GPSS 1 Check whether the GPS antenna is properly connected and placed Check whether entered telephone numbers for sending alarm SMS s are correct Check whether the GPS antenna is placed horizontally and is not obstructed from the top by metal parts of the vehicle The device dispose of a sophisticated algo rithm for activation of GPS alarms In very rare cases an activation of false alarm may occur which does not have to be caused by defect of the device or wrong installa
11. d49 7743E 20km h 10 09 10 10 02 04GMT 02 00h INPUT protection To be able to utilize INPUT protection mode it is necessary to have ex ternal car alarm installed which output is connected to input contact of the LOC200 INPUT protection sends SMS to authorized telephone number in case that the condition for INPUT alarm activation on input contact of the LOC200 is met Note We recommend to have the external alarm connection done by a professional service e Activation of protection INPUT protection is permanently Reaction to alarm Alarm SMS s with the car position data are being sent during the whole alarm duration The total number of alarm SMS s depends on a momentary configuration see 29 May 2015 AMPIE Electronics All rights reserved May 2015 AMPIE Electronics All rights reserved active considering proper installation and connection of ex ternal car alarm with the LOC200 was done Deactivation of protection INPUT protection can be deacti vated by disconnecting external alarm from input contact of the LOC200 INPUT alarm activation INPUT alarm is activated when ex ternal car alarm gets activated In case the GPS alarm was already activated the INPUT alarm will not be activated protection against cyclic communication with external car alarm Reaction to alarm One alarm SMS informing about car at tact is sent after INPUT alarm is activated Such SMS may contain also information ab
12. ed GPS alarm z 1 to 30 This parameter A Example Switch the relay for 240 is optional and will be automatically set to value minutesafterthe vehicle N10 in case the parameter was not entered 4321 STOP 1 has stopped Default setting T5 N10 Command STOP 1 switches the relay in GPS locator for 240 minutes if speed of the vehicle is 0 Km h In case of sending command while current speed of the vehicle is higher than 0 Km h the relay will switch after the vehicle has stopped After the command execution relay switch the unit sends SMS with exact location where the relay switched 4321 PERIOD D4 N5 First alarm SMS is sent immediately after GPS alarm activa tion and next alarm SMS s are sent every time after either set distance in kilometers is covered or set time in minutes Number of sent alarm SMS s within one activated GPS alarm By sending command STOP 1 repeatedly the relay switched time can be extended Device ETLOC 30 is not an immobiliza tion device and mustn t be used to immobilize a vehicle May 2015 AMIP IRE Electronics All rights reserved May 2015 AMPIE Electronics All rights reserved is determined by parameter Nz The GPS alarm is automati cally deactivated when all SMS s are sent However the set mode of protection is still active If the vehicle keeps mov ing new GPS alarm is activated Configuration of SMS text sent at GPS alarm activation Command format GTEXT xxxxx XXXXX you
13. ed when the vehi itself automatically OFF for the time of driving after car igni cle starts moving while car igntion is OFF e g towing tion is set ON Reaction to alarm Alarm SMS s with a car position data are being sent during the whole alarm duration The total num ber of alarm SMS s depends on a momentary configuration see configuration command PERIOD The activated GPS alarm can be deactivated by ringing the telephone number of LOC200 from authorized telephone number alarm deac tivation is confirmed by immediate rejection of the call by LOC200 Function of GPS protection stays active until deac e Activation of protection The GPS protection is activated us tivated by command GPS 0 ing command GPS 1 If the protection is activated the car will be automatically protected every time after ignition is Default text setting change is set OFF possible by command GTEXT e Deactivation of protection The GPS protection can be deacti Speed of the vehicle vated using command GPS 0 There is no need to deacti vate protection using any command before every single driv ing since protection is deactivated automatically after car ignition is set ON GMT and time correction see the note below 4321 GPS 1 Alarm Position and gi speed of your car 50d 11 2842N 015d49 7743E 20km h 10 09 10 10 02 04GMT 02 00h 4321 GPS 0 27 May 2015 AMIP IRE Electronics All rights
14. fitted with faston connector when the ignition is ON Beware of the polarity of battery contact Connection of other wires from the cable harness is optional May 2015 AMIP IRE Electronics All rights reserved May 2015 AMPIE Electronics All rights reserved Schema GPS locator connection into the the vehicle with onboard power 24V INPUT IGNITION GPS LOCATOR REPLAY YELLOW CONVERTOR 24 12V A 24V CAR May 2015 ADAP IRE Electronics All rights reserved Configuration The LOC200 configuration is performed using instructions sent as an SMS from your mobile phone to the phone number of the LOC200 Command is always sent together with PIN code which defines authorized user s The PIN code is a fourdigit number which can be changed The PIN code is set by manufacturer to value 4321 symbols are used instead of PIN code in the text below The commands can be typed both in regular or capital letters In case the command is not sent in a correct form the LOC200 will send SMS with the text COMMAND ERROR In case the command is sent with incorrectly entered parameters the LOC200 will send SMS with the text key word ERROR Entering of authorized phone numbers for alarm SMS and controlling of GPS higher level protection mode Command format PHONE aaaz bbbz cccz aaa first authorized number in international format bbb second authorized number in in
15. in 6 Orange Pin 10 2x black Pin11 Red Pin 12 Red white Switching relay common contact COM Switching relay opening contact NO Switching relay closing contact NC External alarm input A0 Input ignition External alarm input A1 Frame 12V backup power source 12V 12V backup power source View into the connector The LOC200 is intended either for separate connection or as an addition to a car alarm 1 Push the releasing button and slide out the SIM card holder Insert the SIM card in the holder and slide back in the LOC200 together with the SIM card May 2015 AMPIRE Electronics All rights reserved At first the SIM card needs to have PIN code protection deac The LOC200 allows connection of backup battery to the tivated The PIN code protection can be deactivated for ex cable connector wires black and red white wire Char ample in a mobile phone ging of the backup battery is done automatically while driving We recommend to use gel battery 12V 1 3Ah The battery endurance is 30 to 60 hours depending on mo mentary operating mode of the LOC200 2 Connect particular wires from cable as seen on the right The cable connector must be disconnected from the LOC200 during wire connecting process Red LED indicates GSM Yellow red and black wires must be always connected Connection DO blinking m The evee eeann ECS MNE
16. only if a pay as you go card is used Setting the LOC200 in STAND BY mode Command format OFF In STAND BY mode the LOC200 is switched OFF and its pow er consumption is 0 mA STAND BY mode is recommended to be used for long time car parking e g in winter time Mode 0 0 Description Power consumption The device is ON and responds to all SMS commands GPS Max 20MA Recommended ma Ready protection and GPS I us vey Were CR using driving the car O IO is 6 weeks tion are OFF The device is ON and Max 40mA GPS responds to all SMS Recommended ma protection commands At least ximum time for not one GPS protection using driving the car is ON is 2 weeks The device is OFF and OMA Standby does not respond to Empfohlen bei sehr any SMS commands langer Parkzeit The power consumption will be temporarily increased by 20mA when the relay is in the switched mode Peste May 2015 AIMPIRE Electronics All rights reserved D In STAND BY mode the LOC200 does not respond to SMS commands and ringing The LOC200 can be woken up from this mode by either switching car ignition ON or by signal on external input external alarm activation Under such conditions the protection mode set before STAND BY mode activation remains active The only limitation will be during protection against car towing away without either alarm activation or switching ignition ON May 2015 AMAP IRE Electronics All righ
17. out a position of a car Alarm Your car was attacked Position SMS request Command format POSITION The LOC200 responds to POSITION command with one SMS May 2015 AMPIRE Electronics All rights reserved containing GPS data The time in which the device responds depends on the fact if the GPS module is momentarily switched ON at least one GPS protection is ON or the car engine is ON and it can also dependon the strength of GPS signal reception In case the locator does not manage to detect valid GPS data within 5 minutes after receiving the request the device sends SMS with last known data marked as OLD in case this posi tion was detected after the device is switched ON The user can send the command POSITION request inde pendently on the state of protections and on the state of activated alarms In case of setting the function LINK to value 1 function is switched ON the LOC200 sends SMS with GPS coordinates in the form of a link to display the vehicle position on the internet Default text setting change is possible by command PTEXT GPS coordinates displaying coordinates in the text form I Position and speed Speed of the vehicle of your car 50d11 2842N Date 015d49 7743E Okm h 10 09 10 GMT and time correction 10 02 04GMT 02 00h 31 May 2015 AMPIRE Electronics All rights reserved e Okm h 10 09 10 10 08 02GMT 02 00h GPS
18. protection i GPF Glion lalla e GPS higher level protection GPSS e INPUT protectionN iii e Position SMS reQueEst e Relay switching for unlimited time e Relay switching for preset time e Relay switching for time preset by command RELAY essre e Request for remaining credit in pay as you go SIM card used in the LOC200 e Setting the LOC200 in STAND BY mode Finding a vehicle position 1 1 11 1 e Finding a vehicle position on server SAIMAPSNET e Troubleshooting 11 11 rrrrriiiiii inni Technical Data 2 10 1202ssasssaraianae anioni aio May 2015 AMPIRE Electronics All rights reserved Introduction Dear customer thank you for purchasing our product It is a modern and technologically advanced LOC200 This product will help you to secure and protect your vehicle car truck motorcy cle caravan construction machine agricultural machine motorboat etc In case the guarded vehicle is stolen the LOC200 will send you a current position to your mobile phone Via mobile phone you can easily view the current map with vehicle position on the display This service of a displaying on a map is completely free of charge You can also view the position of a guarded vehicle via PC and web site http
19. r text of the message max 74 symbols Default setting Alarm Position and speed of your car 4321 GTEXT They are stealing your car The SMS with GTEXT will be sent to a preset telephone num bers after GPS alarm activation The GPS data will follow after this text in the alarm SMS May 2015 AD4PIRE Electronics All rights reserved Configuration of SMS text sent at INPUT alarm activation Command format ITEXT xxxxx XXXXX your text of the message max 74 symbols Default setting Alarm Your car was attacked 4321 ITEXT Car alarm is activated The SMS with ITEXT will be sent to a preset telephone num bers after INPUT alarm is activated In case the ITEXT ends with symbol the GPS data will follow after the ITEXT in the alarm SMS Configuration of SMS text sent as a response to a position request Command format PTEXT xxxxx XXXXX your text of the message max 74 symbols Default setting Position and speed of your car May 2015 AMPIRE Electronics All rights reserved 4321 PTEXT Your car is right here The SMS with PTEXT is sent as a response to a vehicle posi tion request see below for the command POSITION to the telephone number used for sending the request This text will be in SMS always followed by GPS data Setting of alert call in case of alarm activation Command format CALL x x 0 call function is OFF X 1 call function is ON Default set
20. reserved May 2015 AMPIE Electronics All rights reserved The LOC200 shows GMT in the SMS s The GMT is a part of the GPS info Some GSM operators provide local time cor rection in relation to GMT If your GSM operator supports such service the LOC200 adds time correction info to the SMS e g 10 02 04GMT 02 00h if not only GMT time is shown e g 10 02 04GMT GPS higher level protection GPSS This mode is identical with GPS protection mode but does not evaluate car ignition status GPS alarm gets activated every time when the vehicle starts moving Activation of protection GPS higher level protection is acti vated by ringing the LOC200 telephone number from autho rized telephone number the LOC200 rings 2x and then re jects the call Deactivation of protection GPS higher level protection is also deactivated by ringing the LOC200 from authorized telephone number alarm deactivation is confirmed by immediate rejec tion of the call by LOC200 Deactivation must be done prior to any drive GPS alarm activation GPS alarm is activated when the vehi cle starts moving configuration command PERIOD The activated GPS alarm can be deactivated by ringing the telephone number of LOC200 from authorized telephone number alarm deactivation is con firmed by immediate rejection of the call by LOC200 By ring ing you also deactivate the mode of GPS protection Alarm Position and speed of your car 50d11 2842N 015
21. t embedded texts of alert and information SMS s e LOC200 setting is done using mobile phone e 4digit PIN code to guarantee security Weight Dimensions e 729 e 68 x 20 x 60mm May 2015 AMPIRE Electronics All rights reserved 2015 AMPIRE ELECTRONICS All rights reserved Reprint is only permitted with a written authorization
22. ternational format ccc third authorized number in international format Z determines whether alarm SMS to this phone number will be sent during INPUT alarm or GPS alarm z INPUT alarm SMS will be sent to this number only z G GPS alarm SMS will be sent to this number only May 2015 AMAP IRE Electronics All rights reserved 4321 PHONE 42077720 0333 420602666888G Parameter z is optional If this phone number is entered without this parameter it means that SMS s will be sent to this phone number from both INPUT alarm and GPS alarm the value IG is set automatically Up to 3 telephone numbers can be as signed All entered authorized numbers can control GPS higher level protec tion mode by ringing the LOC200 number see below The telephone numbers must be entered in international for mat so the number must always begin with the symbol Authorized telephone numbers must have identification of calling number CLIP activated In case this function is not active function of GPS higher level protection cannot be controlled and it is not possible to control the LOC200 by ringing The first authorized number set by command PHONE is called in case of INPUT alarm or GPS alarm activation Condi tion for calling the first authorized number is activation of this function by a command CALL May 2015 AMPIRE Electronics All rights reserved Switch relay configuration at alarm activation Command format RE
23. ting 0 4321 CALL 1 If the function is ON the first set authorized telephone number is automatically called after alarm activation This May 2015 AMPIRE Electronics All rights reserved alert call is only warning the user about activated alarm We recommend not to accept the call the locator does not dis pose of any voice functions Way of sending GPS coordinates in SMS s Command format LINK x x 0 sending GPS coordinates in the text form lt 1 sending GPS coordinates in the form of a link which shows the vehicle position on the internet Default setting 0 4321 LINK 1 If this function is ON the LOC200 sends a message with GPS coordinates in form with a link Now the user can just click on the link contained in SMS and view the position of the vehicle on internet maps 21 May 2015 AMPIRE Electronics All rights reserved If you want to use this function your mobile phone must be connected to the internet and must support the web brow ser function The service of displaying a vehicle position on the map is completely free of charge Setting of confirmation message for SMS commands Command format CONFIRM x X 0 confirmation messages OFF x 1 confirmation messages ON Default setting 1 If the confirmation message function is ON after successful command processing the LOC200 sends SMS with the text command OK to the telephone number sending original
24. tion This situation might happen in garages and close to high buildings where the device can receive for longer time bad or reflected GPS signal Please contact your dealer the device can be set to its default factory setting including the PIN only by a manufacturer berpr fen Sie die G ltigkeit der autorisierten Telefonnummern einschlieBlich der Landervor wahl indem Sie den Befehl CONFIG benutzen berpr fen Sie ob die autorisierten Nummern den CLIP Service aktiviert haben Identifizierung einer Anrufnummer May 2015 AD4PIRE Electronics All rights reserved Technical Data e Quad Band GSM 850 900 1800 1900MHz e Compliant to GSM phase 2 2 Class 4 2 Watt GSM850 900MHz Class 1 1 Watt GSM1800 1900MHz Modern integrated GSM antenna 900 1800 1900 MHz Receiver 20 channels L1 1575 42 MHz C A code 1 023 MHz chip rate Accuracy Position 2 5 m CEP Chip set SiRF star III GSC3f Hot start lt 1 s average open sky Warm start 35 s average open sky Cold start 35 s average open sky Support AGPS Low power consumption 160mW at 3 3 V full power Protocols NMEA 0183 SiRF binary RTCM SC 104 Crystal oscillator TCXO temperature compensated with frequency stability of 0 5 ppm Stromversorgung Stromverbrauch Vehicle onboard power 12V DC Ready The device is ON and responds to all SMS commands GPS protection is OFF max 20mA GPS protection The device is ON and responds to
25. ts reserved WA ae As Finding a vehicle position 1 Finding a vehicle position on server SATMAPS NET Enter internet address www satmaps net to your internet browser 2 Type the GPS coordinates received by SMS in Latitude and Longitude fields 3 Click the button Show position and wait for showing the position of your vehicle on a map Position and speed of your car 45036 1935N gt 009d27 9519E Okm H 10 09 10 10 08 02GMT 02 00h inmp ess e 1 Sie oll geld eee a E de AI aan May 2015 AMPIRE Electronics All rights reserved Troubleshooting Problem The device does not switch ON The device does not log in GSM network red LED is blin king in interval 1x per second The device does not respond to SMS commands The device responds to SMS commands but does not respond to ringing from authorized telephone number Solution Check the connection of power supply wires and wire input ignition and switch car ignition ON Check whether the SIM card is properly inserted Check availability of GSM operator signal Check whether inserted SIM card has disabled PIN code protection After successful logging the red LED must blink in interval 1x per 3 seconds Check whether the device is switched ON and logged in GSM network The logging in the GSM can be also verified by ringing the device Make sure that commands are entered in
Download Pdf Manuals
Related Search