User Guide for an Electrical Socket with
Contents
1. the warranty claim expires For conseguential damage we do not assume liability 4 We do not assume liability for any material and personal damage that is the result of inappropriate operating or disregarding the safety information For security and authorization reason it is not allowed to convert or change the device arbitrarily Please consider the security information and instructional devices for the con nected devices Please consider the security information of the individual chapters of this man ual instructions Do not let the packing materials laying around carelessly they could become a dangerous toy for your children The electrical installations and equipment s in industrial facilities must be observed by the security regulations and insurance institutions If you are not aware of a correct connections or may there be any question that have not been answered in the user guide please contact us Return of old devices If the control of a socket board with temperature monitoring becomes worn out please bring your worn out device to the community recycling center e g recycling depot The worn out device needs to be disposed separately from your household rubbish According to the electric and electronic device law the owner of an old device is lawfully upheld to dispose old electric and electronic devices separately from the household rubbish Please assist and contribute your share to environmental2. protection by not disposing your old devices in the household trash 5 DOC DECLARATION OF CONFORMITY 5 DOC Declaration of Conformity The company W hlke EDV Beratung GmbH Griitzmacher Str 4 D 28844 Weyhe Tel 49 421 802791 0 Fax 49 421 802791 18 info woehlke edv de www woehlke edv de declares hereby that the product Web Controlled electrical socket with temperature monitoring via the internet agrees with the clauses of the following EU guidelines 2004 108 EG Electromagnetic compatibility 2006 95 EG low voltage directive and the following norms were applied EN 55022 2010 AC 2011 Establishment of information technology Radio interference properties limiting values measurement method EN 55024 2010 Establishment of information technology Interference immunity properties limiting values testing procedure EN 61000 3 2 2006 Electromagnetic compatibility Part 3 2 Limiting values for harmonic currents EN 60950 2006 Security of facilities of the information technology Weyhe April 23 2013 Prof Dr Eng W Wohlke Business Executive
3. 2013 3h after gt sunrise switthon 10 gt August 2013 11 05 gt switch off gt 16 gt May 2013 13 59 T gt switch off gt 16 May 2013 13 59 v switch off 7 16 May 2013 13 59 switch off gt 16 gt May 2013 13 59 v switch off 16 gt May 2013 13 59 switch off 16 gt May 2013 18 59 switch off gt 16 gt May 2013 13 v 59 T gt switch off back Save Figure 16 Setting of onetime switching actions First of all you select the checkbox below the point active in the line in which you want to change settings Choose a date time and switching action in this line or select Astro to switch the sockets depending on the sunrise or sunset You have the possibility to determine ten onetime moments at which the socket shall be switched Confirm your entry with Save The data that were entered by you will be arranged chronologically When you want to delete a switching action remove the checkmark at the beginning of the respective line and click Save Attention In case of a blackout or any other incident that prevents the Electrical Socket from switching there will be an entry error_log data This function is only active during single switching 1 USER GUIDE 18 Example Socket 3 daily switching Choose below the point Time switch gt Socket 3 gt Daily The following
4. If temperature monitoring is activ you will get an e mail every time you restart the electrical socket 1 USER GUIDE 25 1 6 Download The Electrical socket logs all switching operations and e mail dispatches in log files that can be read with this function Download Log file switching events download User manual link to user manual Log file Email dispatch download Figure 22 Download log file To view these files click with the left mouse button on the link download The recent shifts are displayed with time and cause of the circuit manual timer or temperature switching On temperature switching you can also see the current termperature at shifting time The log file for switching operations is limited to 1000 entries and when an overflow occurs the oldest entries are deleted first In the e mail logfile date time and number of the registered e mail address 1 2 or 3 is displayed and the status OK or ERROR To save the files on your computer click the link download with the right mouse button Choose from the following selection to the point Save file as Give a destination and confirm with Save The saved files are text files that can be edited with a simple text editor Also you find a link to download the usermanual 1 USER GUIDE 26 1 7 Update The Electrical Socket is eguipped with an automatic update function which makes it possible if reguired to search for updates of the software automatical
5. Configure Time switch download area Current switching status max temperature 24 C temparature in C min temperature 22 C 26 Y w 8 3 ES 10 00 11 00 Figure 4 Home Page of the Electrical Socket When you put the web electrical socket into service for the first time please choose the menu item Settings and configure the web electrical socket For the actual switching procedures and temperature monitoring you find the menu items left in the navigation box or respectively as a navigation point on the front page By clicking on this menu item Home you return to this page at any time 1 USER GUIDE 7 1 3 Settings In order to adjust the individual settings to the socket board choose the menu item Settings on the homepage W hlke Current 16 05 2013 SNT New manual Synchronise with the internet Area Berlin Figure 5 Settings of the socket board On this page the settings below can be made Confirm your entries in the corre sponding sections always by Apply otherwise changes will not be accepted e Date and time e On position of the socket board and labeling e Network connection LAN and or WLAN e Hostname e Password protection for the homepage e Webserver HTTP Port e Priority for simultaneous operation of timer and termperature switching e Reboot the system e Used temperature sensor 1 USER GUIDE 8 1 3 1 Date and Time Below the menu item Settings gt Date Time you have the possibil
6. fails or is removed and the temperature switching is activated for the respective socket regardless of the programmed switching states 1 3 4 Network Settings Below the menue item Settings gt Network you configure the socket board individ ually for your network By clicking on the box before LAN or WLAN you chose how your electrical socket shall connect with the network Both ways can operate parallel Confirm your settings always with Apply LAN Configuration Please decide first of all whether you want to use the con nection via DHCP or a LAN adapter with a fixed IP address If your router is set on DHCP the IP address can be assigned automatically By entering the hostname into your browser you connect with your Electrical Socket tested with FritzBox The other way to connect is by using the IP address the router has allocated to the LAN adapter If your DHCP has not been set or you want to have a fixed IP address for the LAN adapter fill out the box IP Address Netmask Gateway and DNS In the box Gateway enter your routers IP address in the box Netmask enter the netmask sub netmask In the box IP address please enter the IP address that the LAN adapter of your Electrical Socket shall get If your netmask is called 255 255 255 0 the first three fields of the IP address need to correspond with those from your gateway The last 1 USER GUIDE 10 LAN configuration WLAN configuration LAN not connected E2IWLAN con
7. page will appear Socket 3 Heizung Daily switching active Astro time action E 00 v 00 switch off gt Ea 11 x 100 7 switch off KA Ea 2h gt after gt sunrise v switch on v lal F 14 yj 05 switch off gt 14 05 switch off 14 x 05 gt switch off gt 14 v 05 7 switch off y 14 05 switch off 114 05 switch off 114 05 vi switch off back Save Figure 17 The setting of daily switching actions First of all you click on the checkbox below the point active in the line in which you want to change settings Then choose the time or select Astro to switch the sockets depending on the sunrise or sunset Determined the type of switching You have the possibilities to determine ten points in time at which the socket shall be switched daily Confirm your entry with Save The data that were entered by you will be arranged chronologically When you want to delete a switching ac tion remove the checkmark at the beginning of the respective line and click Save The settings for particular weekdays take place in the same way as the settings for daily switching All settings will be implemented parallel If a socket shall be turned on and off at the same time then the switching off process has priority 1 USER GUIDE 19 Via Time switch gt Display error log you can display which onetime switching actions for example because of a blackout could not be cond
8. to turn off above the temperature threshold you should select choice number two If you want the socket to turn on above the temperature threshold and to turn off below the temperature threshold choose option number three If the socket shall not switch depending on the ambient temperature select option number one deactivate In order to apply the settings confirm with Apply 1 USER GUIDE 21 An example A profile is created and you have set socket no 1 and no 2 in a way that they turn on at 8 00 and turn off at 22 00 every day Now you decide that a temperature sensor should be connected to socket no 3 and that this socket should always turn on above 30 C and turn off below 20 C Time switch for no 3 is inactiv So switch off all switching times for the third socket Now click on the menu item Temperature switching and enter temperature value 1 20 C and temperature value 2 30 C Fi nally you activate option number three for socket no 3 and then confirm your entry with Apply Socket no 1 and no 2 continue to turn on at 8 00 and turn off at 22 00 but socket no 3 only turns on if the ambient temperature of 30 C exceeds and turns off if the ambient temperature comes below 20 C Combination of time switch and temperature switching is also possible when a pro file is selected for the timer The switching state has priority which is set under Settings gt Time Switch amp Temperature Switching gt Priority 1 Priority switch
9. 24 hours 1 USER GUIDE 23 1 5 2 Temperature Monitoring Connect the supplied temperature sensor with the front side of the socket Choose on the homepage the menu item Monitoring gt Temperature monitoring The following page will appear W hlke Monitoring Current temperature 24 C Configure Temperature monitoring Temperature values Temperature value 1 12 C v Temperature value 2 27 ec Additional Email text Temperatur Email Account Email address n skyline gmx de Username n skyline gmx de Password 00000000000 Mail server mail gmx net e g mail provider org Mailserverport 25 SSL Receiver Email 1 max mustermann gmx net Email 2 abc test com Email 3 Apply Figure 21 Temperature indicator and settings The current temperature will be shown on the socket board at the temperature sensor The temperature range of the sensor lies between 40 C and 100 C On the homepage you have the possibility to enter one or two temperature thresh olds If you do not want to enter any thresholds please select in the appropriate field deactivate In the following fields you can enter information about your email account and three email addresses If the entered threshold is exceeded or deceeded an email is send to every email address with information about date and time 1 USER GUIDE 24 Confirm your entry with Apply Conseguently a test email is sent to the entered email addresses
10. IP Working temperature 0 C 40 C Operating Humidity 10 85 non condensing WLAN transmission standard 802 11b g n WEP WPA WPA2 encoding Length 482 mm Width 74 mm Height 45 mm 1 12 System Reguirements The homepage was tested on the browsers Internet Explorer 7 0 8 0 und Firefox 3 6 16 For the display of the homepage Java Script needs to be activated in your browser 2 SAFETY INFORMATION 33 2 Safety Information Please consider when putting up connecting and operating the socket the following hints e Put the device on a non slip mat e Lay the connections accident proof e Do not put the device close to sources of heat in direct sun light or close to electrical devices e Protect the device from wetness dust aggressive liquids and steam e Connect only to authorized user e Research has proven that in some cases medical devices can be influenced by wireless signals For that reason please observe the regulations of medical facilities before using the web electrical socket within these facilities e Never open this device by yourself never touch the socket with lacy and metal objects and never carry the device at the connection cord e Never use the device in wet rooms e g bathroom or in explosion prone areas e Do not use the provided temperature sensor in liquids 3 SAFETY STATEMENT 34 3 Safety Statement For any damage or harm that is the result of disregarding this instruction manual
11. User Guide for an Electrical Socket with Temperature Monitoring via Internet V 3 2 0 x Please note Before commissioning read the instruction manual very carefully 24th July 2013 W hlke EDV Beratung GmbH Griitzmacher Str 4 28844 Weyhe Contents 1 User Guide 4 LA OTE EEA EKA EIRA ESATA JA Dara be Ge ee R EPA 4 12 COSSIO s gegen ma tora WEIN Ge Aly ee A ee ey 5 1 2 1 Activate DHCP in the router 5 1 2 2 Deactivate DHCP in the router 5 1 23 Home Page of the Electrical Socket 6 A a ae isk nan alta Tan en Kain He che Koi gee Bo gh kone Be 7 13 1 Date and ME staps prag 84 0 2308 KAJE A 8 1 3 2 On position and Labeling sa Eka E Akkaa 8 1 3 3 On position and Labeling 9 1 3 4 Network Settings lak ne A KKK aah 9 1 3 5 Hostname and Webserver kkk kkk knee 11 1 3 6 Password Protection sii son pt 2b de and 11 1 347 Further Settihgse 3 03 ea te ee mika hate ee Sa 12 LA Sele e bos ct date ka Ge d he ee ek Ak 14 1 4 1 Manual SUCIAS a E ee So ek a Sa ac 14 1 4 2 Time Switch SOAS nie KSM eS dk kand 15 1 4 3 Temperature Switching 0 20 Lio MONITOR at s Lok a ee eNO de da o mus 22 1 5 1 Temperature curve hs Ke 22 1 5 2 Temperature Monitoring se 23 L Download eta od oia ee do NOSO toe Rowe Ysi MESE Boe eee 25 LU Pd aw dae oe ene hn ek een Sor ee PS ee at eek 26 ao ata Se op cat ie a RR ani ain Woo Se IO 27 1 9 Netw
12. a Dyndns com In order to connect to the socket via the internet the socket needs to be connected to an online router In addition the IP address of the router needs to be known and the IP address can be assigned automatically and has to be fixed If a fixed IP address is not assigned to the router by the internet provider the IP address of the router will be changed every 24 hours The service provided by DynDNS can assign a guasi steadily IP address to the router Thereby it is made possible to connect to the web electrical socket via a do main that was selected by DynDNS Moreover the IP address of the web electrical socket cannot be obtained automatically but has to be assigned consistently In order to obtain a domain proceed as follows Enter in your browser the address www dyndns com Select on the homepage the menu item Sign In and afterwards select the menu item Create an Account DNS amp Domains O DynDNS Why DynDNS com Services amp Pricing Support My Account Create an account or log in to continue Create Account U FE Lon AISTI Already Registered Lost Password Password f Username Confirm password f pesa N Password E Email Confirm Email E x Eorgot your password WE RE HIRI Security Image f HS N gt tn g Xe SERS ASA SE MA NESSN Powered by y Dyn Enter the numbers from the above image Subscribe to y DynDNS com newsletter 1 or 2 per mont
13. ce Offline Hostname Sync Expirations Account Settings IP Address Billing My Cart Qitems TTL value is 60 seconds Edit TTL Mail Routing I have mail server with another name and would like to add MX hostname WE RE Add To Cart Powered by O Dyn Figure 26 Create a host on DynDNS Enter in Hostname your individually selected domain name and select a domain ending so that you domains name is for example Steckdose2006 dyndns org In the field IP Adresse your router s IP address will be shown Confirm your entry with Add Host Now you have registered successively on dyndns com DDNS must now be enabled on your router In this case select dyndns org as your provider All access and domain name from dyndns org must also be entered in the router Finally a port forwarding in your router is set up if you use a different port 1 USER GUIDE for your electrical socket other than the default port 80 You can now connect the homepage of your socket via the selected domain Example http Steckdose 2006 dyndns org 65000 31 1 USER GUIDE 32 1 11 Technical Data Connections 1 x Ethernet connection RJ45 3 x load current connections 1 x mains current connection Power supply 230 VAC Power consumption 2 5 W Switching capacity per Electrical Socket 3600 W the maximum of 3600 W for all three sockets must not be exceeded Network connection 10 100 Mbps WLAN up to 150 Mbps Protocols TCP
14. ct the access of your homepage with a password Fill in the fields and confirm 1 USER GUIDE 12 your entry with Apply Password protection New username Mustermann New password 00000000 Repeat new password 00000000 Apply Figure 11 Create a password 1 3 7 Further Settings Below the menue item Settings gt Other you will find further settings Under Temperature Sensor you can chose between three types of sensors 3m 10m 20m Below the point Reboot you can restart the system which should not be mistaken with Reset chapter 1 11 which sets the settings back to factory settings In the area Service you can simulate the software e g toa previous state if an update was not successful Give software in the box under Service and press Apply This allows you to re run an update Below Time Switch and Termperature Switching you can define the default prior ity This setting is relevant when Time Switch while Temperature Switching is used Time Switch and Temperature Switching Temperature sensor Priority switch on Type 3m Apply Apply Reboot Service Tip The system of the Web Power Contro will be Tip Only for service engineers infended restarted Apply Apply Figure 12 Further Settings Possible application by using time temperature switching and time switch at the 1 USER GUIDE 13 same time The socket switches at different temperatures Determined by the timer the socket should a
15. h Dyn Inc press releases I agree with the acceptable use policy AUP and privacy policy Create Account If you re having difficulty creating your account for any reason feel free to contact us Figure 25 Form Create Account by DynDns com 1 USER GUIDE 30 Fill out the displayed form Confirm your entry with Create Account The email address that you have entered can only be used once If there is a problem during the account creation and you try to create an account again you have to use an alternativ email address Afterwards you will receive an email to the email address which you have stated in the form Follow the link in the email and log in with your chosen username and password on DynDNS Now select on by one the menu items My Services gt Add Hostname Fill out the shown form O DynDNS Why DynDNS com Services amp Pricing Support Welcome alisee84 Ez DNS amp Domains Email Services My Account Add New Hostname 1 Host Services My Services You don t currently have a Dynamic DNS Pro service in your account Dynamic DNS Pro To get the full benefits of Dynamic DNS including premium subscriber domains and other features add Dynamic DNS Pro to your shopping cart or try it with 1 99 monthly subscription Hostname dyndns work com bed Wildcard only for DynDNS Pro users Service Type O Host with IP address WebHop Redirect URL forwarding servi
16. have changed the IP address of your computer during the first settings restore the original settings Test your computer by check ing if it can connect with the internet In order to get to the homepage of the socket board enter your selected hostname into your browser tested with FritzBox and DHCP or use the individuell IP ad dress of your electrical socket Via this entry every computer that uses the same network can access to the homepage of the socket board If you cannot connect with the Electrical Socket check the settings and start maybe again with the first settings 1 3 5 Hostname and Webserver You need an individual hostname if you let DHCP automatically assign an IP ad dress The preset hostname is websteckdose In this case you can connect with your Electrical Socket by entering the hostname into your browser tested with FritzBox With the item point Webserver you can set an alternative HTTP port By default port 80 is set If necessary enter an alternate port and confirm your choice with apply In this case enter the alternative port address always with a colon when you want to achieve the electrical socket Examples 192 168 101 6 65000 websteckdose 65000 http Steckdose 2006 dyndns org 65000 Hostname Webserver Websteckdose HTTP Port 80 Apply Apply Figure 10 Hostname and Webserver 1 3 6 Password Protection Below the menue item Settings gt Password Protection you have the possibility to prote
17. home page of the electrical socket 1 2 2 Deactivate DHCP in the router In order to create a connection with the socket you need to change the settings on your computer according to the following information e IP address 192 168 101 x gt x any except 6 e IP subnet mask 255 255 255 0 e Gateway 192 168 101 254 ATTENTION Note on your computer the previous settings before you change them as they are important for your internet access After the commissioning of the socket board you need to recover these settings Type the IP address 192 168 101 6 into your web browser You are now at the front page of the homepage lFor control purposes the electrical outlet number 2 will turn on for a short moment until it will switch back to the set position 1 USER GUIDE 6 1 2 3 Home Page of the Electrical Socket On the front page you receive all the important information such as the current temperature chosen profile the latest switching status of the socket as well as the temperature profile of the last 24 hours With every restart the temperature profile will start from the beginning again During operation the homepage is updated every 10 seconds Wahlke Home Websteckdose Current temperature 22 C Current profile Sommer Configure temperature monitoring 4 7 E gure p Configure temperature switch gt Configure profile Current profile 1 OFF 2 OFF 3 ON Manual switching gt Temperature curve
18. ity to set date and time You can also state whether you would like to synchronize the data with the internet Online synchronization will always start at 12 00 am In order to adjust date and time please choose the desired values and confirm your entry by Apply Current 16 05 2013 Es New manual Synchronise with the internet Area Berlin Apply Figure 6 Adjust date and time 1 3 2 On position and Labeling Below the menue item Settings gt Other you can specify a base state Switching states at power up inscription Socket 1 oon off Pumpe Socket 2 on off Heizung Socket 3 on off Lampe Apply Figure 7 Set the on position This state will be adopted by the socket after the socket board was connected to the electricity grid or has been turned on or alternatively after a blackout Choose the desired state for every socket board You can also enter a label for every single socket board Confirm your entry with Apply 1 USER GUIDE 9 1 3 3 On position and Labeling Below the menue item Settings gt Other you can specify a base state when the temperature sensor fails or is removed Switching states at missing temperature sensor Socket 1 on o off Tip Only if temperature switching of the Socket 2 Son off respective socket is activated Socket 3 aon off Apply Figure 8 Set the on position The sockets go into these defined state when running during the operation and the temperature sensor
19. lso remain switched on or off in a given period Priority switch on The selected socket is switched on when timer or temperature switch are on and off when both turn off Priority switch off The selected socket is switched off when timer or temperature switch are off and on when both turn on Default is switch on Select the switch priority and confirm your entry by Apply 1 USER GUIDE 14 1 4 Switching 1 4 1 Manual Switching Select the menu item Switching gt Manual Switching on the homepage The fol lowing page will appear W hlke Switching Socket 1 on of Lampe Socket 2 On Of Pumpe Socket 3 On Of Heizung OFFJOFFI mii Figure 13 Manual switching The current state of the socket is shown in the socket picture Using the button which is located below the socket picture the individual sockets can be turned on or off 1 USER GUIDE 15 1 4 2 Time Switch The function of a time switch enables you to determine the times at which your socket turns on or off For every individual socket a single daily or weekly point in time can be defined at which it shall turn on or off These settings will be saved in your profile and you can create up to four profiles Select the menu item Switching gt Time switch on the homepage It appears on the following page W hlke Create profile name NO deakt Info By the replacement of a profile all entries
20. ly W hlke EDV BERATUNG Info After pressing Run update itis first checked whether software update is available With success a software update is carried out This event takes about three minutes Advice Please restart the Web Electrical Socket before update Important Please don t switch off the Web Electrical Socket during the software update otherwise the software could be damaged Run Update Figure 23 Update function When you click on the button Run update updates will be downloaded and installed automatically Upon successful update a status message appears just as if your software is up to date 1 USER GUIDE 27 1 8 Information W hlke EDV BERATUNG Software 3 1 9 1 www woehlke websteckdose de Hardware 3 0 0 W hlke EDV Beratung GmbH Gr tzmacher Str 4 LAN MAC 00 05 14 00 20 57 28844 Weyhe WLAN MAC 00 a1 b0 50 03 f9 Germany Phon 49 421 80 27 91 43 LANip 1192 189 101 118 Fax 49 421 80 27 91 18 WLAN IP 192 168 2 118 state online E Mail inforcowoehlke websteckdose de Last time update 12 00 17 05 2013 Figure 24 Information On the information page on the website you can find contact information from the company Wilfried W hlke EDV Beratung GmbH including telephone number fax number email address On that site you can also find the newest software and hardware versions as well as MAC and IP addresses for LAN and WLAN adapters The date of
21. nected Get IP address automatically Get IP address automatically Using the following IP address amp Using the following IP address IP address 192 168 101 118 IP address 192 168 2 118 Netmask 255 255 255 0 Netmask 255 255 255 0 Gateway 192 168 101 254 Gateway 192 168 2 1 DNS 192 168 101 102 DNS 192 168 2 1 Network name SSID DSL6k Security options WEP Key 000090090000000000 Scan network Apply Figure 9 Network settings field is decided by the individual address Please make sure that no other device that is connected to this network is being used In field DNS you generally enter the IP address of your router but you can also enter an alternative DNS server WLAN Confirguration Up to the field Network name SSID you can precede the same as in the LAN configuration When you have already configurated the LAN settings assign a individual IP ad dress for the WLAN adapter Then enter the network name SSID which is set on your router for WLAN Spaces in the network name are not supported so please remove possible spaces from your SSID By clicking on the button Scan network all picked up networks will be shown Choose the right network Preset security options WPA mode and encryption key These settings need to correspond with the router s security settings Your WLAN password can not contain special characters 1 USER GUIDE 11 Network settings check If you
22. of fhe previous profile are deleted create a profile Select a profile deakt y Selected profile Sommer Apply Figure 14 Choice and creation of a profile At least one profile needs to be created and afterwards at least one profile needs to be chosen After the profile is chosen and you pressed Apply the following page appears 1 USER GUIDE 16 W hlke Switching Create profile name no deakt create a profile dd EA ja ISIN of a profile ali entries of the previous profile Select a profile dealt Selected profile Sommer Apply i N i coordinates latitude 53 longitude 8 8 Current Times Sunrise 05 25 Sunset 21 16 Save Chose switching moment Socket 1 Socket2 Socket 3 Lampe Pumpe Heizung One time One time One time Daily Daily Daily Mondays Mondays Mondays Tuesdays Tuesdays Tuesdays Wednesdays Wednesdays Wednesdays Thursdays Thursdays Thursdays Fridays Fridays Fridays Saturdays Saturdays Saturdays Sundays Sundays Sundays Figure 15 Selection of a time switch Now you can choose which socket should be turned off 1 USER GUIDE 17 Example Socket 2 Single switching Choose below the point Time switch gt Socket 2 gt One time The following page will appear Socket 2 Pumpe One time switching active Astro date time action 19 March 2013 10 o0 switch on a 2 29 v June
23. on Keep the power on or switching on has higher priority Temperature switching or timer will switch on the socket The socket will remain on as long as temperature switching and timer will switch off Application The socket should switch depending on the temperature Regardless it is switched on during a certain period determined by the timer 2 Priority switch off Keep the power off or switching off has higher priority Temperature switching or timer will switch off the socket The socket will remain off as long as temperature switching and timer will switch on Application The socket should switch depending on the temperature Regardless it is switched off during a certain period determined by the timer 1 USER GUIDE 22 1 5 Monitoring 1 5 1 Temperature curve The function Monitoring gt Temperature curve shows the temperature history of the last 24 hours Optionally you can also view the progress of the last 7 days or 28 days You have also the possibility to download the hourly temperature values in a CSV file up to 365 days W hlke Monitoring Temperature profile of the last 24 hours temperature in C 27 21 14 00 15 00 16 00 17 00 18 00 19 00 20 00 21 00 22 00 23 00 00 00 01 00 02 00 03 00 04 00 05 00 06 00 07 00 08 00 09 00 10 00 11 00 time max temperature 25 min temperature 23 C 24 hours 7 days 28 days download Temperature loafile Figure 20 Temperature curve over
24. ork settings and Password resetting se 28 1 10 Create a Domain via Dyndns com ss avs A AA 29 Ek Technical Data it ER EN nta ak a Ft ie oat Fe ec 32 1 12 System Requirements amp aout aa IR AAA 32 2 Safety Information 33 3 Safety Statement 34 4 Return of old devices 34 5 DOC Declaration of Conformity 35 1 USER GUIDE 4 1 User Guide 1 1 Overview Figure 1 Multiple Socket Outlet 1 Main on off switch 2 4 Sockets 1 2 3 5 Adapter Power Cable 6 Adapter LAN cable temperature sensor RESET button Figure 2 Head side without connecting cable Figure 3 Head side with connecting cable 1 Adapter temperature sensor 2 Adapter LAN Cable 3 RESET button 1 USER GUIDE 5 1 2 Commissioning Connect the socket board via LAN wire with the router Plug the power plug in the socket Turn on the socket using the green switch on the front side 1 2 1 Activate DHCP in the router Wait 30 second until you start a web browser for example Mozilla Firefox Enter the hostname of your electrical socket The preset hostname is named websteckdose By entering websteckdose you reach the home page of the electrical socket tested with FritzBox If you have no success with this installation login to your router and find out the IP address that was assigned to the LAN adapter of your electrical socket Enter the IP address determined in the form xx xx xx xx in the address bar of your browser This will take you to the
25. the last time synchronization can also be checked Your see wether the electrical socket in on or offline 1 USER GUIDE 28 1 9 Network settings and Password resetting The socket board is eguipped with a reset key In case you forget the IP address of your socket and or your password for the homepage you can reset the socket with the reset key back to factory settings Hereto you have to hold the reset key for at least 3 seconds The reset key is located on the right next to the LAN connector and needs to be pressed by a thin object for example a paperclip After reset the following values are set for the socket e IP address LAN 192 168 101 6 if there is not DHCP e IP address WLAN 192 168 101 7 not activ e Net mask 255 255 255 0 e Gateway 192 168 101 254 e DNS 192 168 101 254 e Connection via LAN e DHCP LAN adapter on e Hostname websteckdose e Username non e Password non e Webserver HTTP Port 80 The settings you have created for the time switch temperature monitoring and temperature switching are saved despite the reset If you push the rest button longer than 15 seconds all individual settings in time switching temperature monitoring and temperature switching will be deleted and set back to factory settings A reset differs from a reboot to the effect that resetting as described restores it to the factory settings and a reboot only restarts the system 1 USER GUIDE 29 1 10 Create a Domain vi
26. ucted This data can be deleted by the button delete error log 16 06 2011 18 04 Profile Ersatz On 16 06 2011 at 18 02 socket 3 vas not switch on 22 06 2011 08 18 Profile Ersatz On 22 06 2011 at 08 16 socket 1 vas not switch on 30 06 2011 02 59 Profile Ersatz On 22 06 2011 at 16 16 socket 1 was not switch off 10 07 2011 02 59 Profile Ersatz On 03 07 2011 at 06 16 socket 1 vas not switch on back delete error_log Figure 18 Display error log 1 USER GUIDE 20 1 43 Temperature Switching Temperature switching provides you the possibility to switch a socket depending on the ambient temperature Select on the homepage Switching gt Temperature switching The following page will appear W hlke Current temperature 24 C i Configure Temperature switching Temperature values Socket 1 Socket 2 Socket 3 Temperature value 1 34 C gt 37 C 24 C Temperature value 2 20 C 22 C 25 C a J Switch the socket depending on the upper and lower temperature Socket 1 Socket 2 Socket 3 Lampe Pumpe Heizung Apply Figure 19 Temperature dependent switching The current temperature will be shown You also have the possibility here to enter two temperature threshold for a switching action of the socket Further down you can select how the particular socket shall switch If you want the socket to turn on below the temperature threshold and
Download Pdf Manuals
Related Search