32-bit PCI-Bus 10/100Mbps ACPI Fast Ethernet Card User's Guide
Contents
1. as well as EIA TIA 568 100 ohm STP cable all qualification under Ethernet cabling rules The maximum cable length run between this adapter and the supporting hub is 300 ft Make the network connection by plugging one end of the cable into the RJ 45 receptacle of this adapter and the other end into the hub 2 5 Drivers and Utilities Diskette The Divers and Utilities diskette contains all the popular operating system drivers Novell NetWare client server Windows NT 3 5 NT4 0 2000 XP Windows 95 98 ME Microsoft Client NDIS 2 0 DOS OS2 Windows For Workgroup 3 11 and so on 2 6 Software Installation Please refer to Quick Installation Guide 2 7 Test Program This test program verifies configuration of the adapter and assists the isolation of any faults in operation Test procedure are optional and will only be useful in the unusual event that there is a fault such as an interrupt number conflict among your computer s add on cards If your installation provides normal operation you do not need these test procedures At your DOS prompt type the following command a rset8139 exe lt Enter gt The opening screen is displayed as following View Current Configuration Set Up New Configuration Run Diagnostics Exit RSET8139 Choose lt Set Up New Configuration gt item allows you to set up the Network Speed 10 or 100M and Transmission Mode Full or Half Duplex and so on Choose lt Run Diagno2. of network adapter This adapter supports 10BASE T 100BASE TX Fast Ethernet and complies with the electrical and protocol requirements of the PCI Local Bus Specification revision 2 2 The Wake On LAN feature is optional for the adapter 1 1 Features The 10 100 Fast Ethernet PCI adapter is a cost effective high performance network interface card It operates in 10BASE T and 100BASE TX modes and integrates easily with Fast Ethernet hub and switch IEEE 802 3 10BASE T and 100BASE TX standards 32 bit bus master for high throughput and low CPU utilization Wake On LAN feature is optional for different hardware version Full duplex operation at both 10Mbps and 100Mbps Supports 10 100Mbps auto sensing capability Rich diagnostic LED mounted on bracket for easily viewing and troubleshooting Single shield RJ 45 connector for using at either Speed Category 3 4 or 5 UTP cable for 10Mbps Operation and Category 5 UTP cable for 100Mbps Operation Plug and Play Installation Test program include Wake On LAN events Network drivers on the diskette for Windows95 98 ME NT 2000 XP NetWare SCO Unix and Packet driver FCC CE certification 1 2 System Requirements To use the adapter you need the following components A PCI master mode expansion slot that is compliant with PCI bus specifications revisions 2 2 A 3 5 inch 1 44MB diskette drive The following cables To operate at 10Mbps a Category 3 4 5 UTP Cable To operate at 1
3. 00Mbps a Category 5 UTP cable 2 Installation This section describes how to install the adapter For connecting to the network you must have the following 1 Network adapter card installed to your computer 2 Cabling compatible with network topology 3 Connect the Wake On LAN cable to the motherboard If the WOL function is supported on the adapter 4 Software for the adapter card contains both configuration utilities and drivers 2 1 Unpack and Inspect Caution Under ordinary circumstances this adapter card will not be affected by static charge as may be received through your body during handling of the unit In special circumstances where you may carry an extraordinarily high static charge it had better reduce the charge by touching a ground before handling the adapter card Open the shipping gift box and carefully remove all items In addition to this User s Manual please check the following items One 10 100 Fast Ethernet PCI Adapter Card One WOL cable If adapter supports WOL function One 3 5 Drivers and Utilities diskette This user s Manual Note If any of the listed items are missing please contact your distributor or reseller 2 2 Install the Adapter 1 Turn off the computer 2 Remove the computer s cover in accordance with its manual 3 Insert the contact edge of the adapter card into the connector of any available PCI Bus master expansion slot Press the card firmly into the
4. 32 bit PCI Bus 10 100Mbps ACPI Fast Ethernet Card User s Guide FCC Statement This device compiles with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Copyright 2002 All right Reserved Document Version 2 0 All Trademarks and trade names are the properties of their respective owners 1 Introduction Congratulations on the purchasing of your new 10 100 NWay Fast Ethernet PCI adapter This document describes the Installation
5. ENT SETUP gt ACPI Wake On LAN function must be enable Step2 Target Machine Select lt Target Machine gt then the system will setup wakeup event and wait a magic packet to do system wakeup Step3 Master Machine Select lt Magic Packet gt to send a magic packet and wake up the target machine The MAC address of target machine will be asked for key in like 00 e0 7d c0 00 02 Step4 Target Machine ACPI Testing events will be show Device State 1 PASS Device State 2 PASS Device State 3 PASS Step5 Target Machine Put the Target Machine to power down mode Step6 Master Machine Send a magic packet to wake up Target Machine Test the Wakeup Frame Step1 Target Machine Select lt Target Machine gt then the system will setup wakeup event and wait a magic packet to do system wakeup Step2 Master Machine Select lt WakeUp Frame gt to send a wakeup frame Step3 Target Machine ACPI Testing events will be show Device State 1 PASS Device State 2 PASS Device State 3 PASS Adapter testing program can not be used in Windows 95 98 DOS mode Do not load any device drivers memory manager and anti virus software The testing program only can work in clean DOS prompt Quick Installation Guide Please take the following steps for driver installation Microsoft Windows 95 Windows 98 Windows ME 1 Turn off the computer 2 Insert the adapter into the available PCI slot 3 Restart the computer 4 After Mic
6. Restart the computer 4 After Microsoft Windows reboot the 10 100Mbps Fast Ethernet Adapter will be found and the system will assign the default network driver to the adapter 5 Select Control Pane from Star menu bar 6 Select Network and Dial Up Connection folder then click Local Area Connection and Properties 7 Click Configure item and select Driver 8 From the Driver item then choose Update Driver 9 The system will prompt two optional for driver search one is auto search and the other is Display a list of known drivers Please select second one Display 10 The system will prompt for driver installation and please select Have Disk button 11 Key in a w98_2000 path to install driver for the adapter Microsoft Windows XP 1 Turn off the computer 2 Insert the adapter into the available PCI slot 3 Restart the computer 4 After Microsoft Windows reboot the 10 100Mbps Fast Ethernet Adapter will be found and the system will assign the default network driver to the adapter 5 Select Control Pane from Star menu bar 6 Select Network Connection folder then click Local Area Connection and Properties 7 Click Configure item and select Driver 8 From the Driver item then choose Update Driver 9 Choose Install from a list or specific location Advancedy and click Next 10 Select Dor
7. connector to PCI slot Please make sure that the cards contacts are fully seated in the PCI slot 4 Install the bracket screw that secures the card to the Computer chassis 5 Connect the WOL cable to the motherboard If adapter supports WOL function 6 Replace the computer s cover 7 Connect the CAT3 or CAT5 UTP cable to the RJ 45 network connector 8 Remove Drivers and Utilities diskette from the PC diskette drive 9 Turn on the computer 70 If the BIOS section of your computer s boot program is Plug and Play compliant then at power up the BIOS will configure any newly installed adapter automatically Note Due to some Plug n Play BIOS programs problem it happens occasionally that a newly installed adapter is assigned an Interrupt Number which is already used by another device adapter In such a case the conflic of Interrupt Number will cause faults in the behavior of both devices Then it is necessary to run the CMOS Setup utility and manually assign a non conflict Interrupt Number 2 3 Connect Fast Ethernet Category 5 UTP cable is required for Fast Ethernet operation The maximum cable run between the adapter and the supporting hub is 300ft 100m Make the network connection by plugging one end of the cable into the RJ 45 receptacle of the adapter and the other end into one port in the hub uekil Pl So 3008 Mini 2 4 Connect 10Mbps Ethernet Category 3 Category 4 and Category 5 UTP cable
8. i t search will choose the driver to install then click Next 11 The system will prompt for driver installation and please select Have Disk button 12 Key in a WinXP path to install driver for the adapter Novell Netware System Please execute the following commands For Netware Client LSL RTSODI IPXODI NETX or VLM F LOGIN lt USERNAME gt For Netware Server LOAD RTSSRV BIND IPX TO RTSSRV The help file in the diskette will describe the detail driver installation information for all popular operating systems F 310
9. rosoft Windows reboot the PCI Ethernet Controller will be found 5 The system will prompt for driver installation 6 Insert the Driver and Utilities diskette into diskette driver and press lt Enter gt 7 For Windows 95 Key in a path to install driver for the adapter 8 For Windows 98 Key in a w98_ 2000 path to install driver for the adapter 9 For Windows ME Key in a w inme path to install driver for the adapter 10 The Windows system will install the driver automatically 11 Reboot the Windows system Windows NT 7 Turn off the computer 2 Insert the adapter into the available PCI slot 3 Restart the computer 4 Click Start menu bar and select Setting item then Control Panel setting 5 Select Network icon 6 If this is the first time to install network on the machine then the system will ask YES or NO to install network adapter Please select YES 7 If the computer already install network before then you need to select Interface gt Add 8 The system will prompt for driver installation 9 Insert the Driver and Utilities diskette into diskette driver and press lt Enter gt 70 Key in a winnt path to install driver for the adapter 11 The Windows system will install the driver automatically 12 Reboot the Windows system Microsoft Windows 2000 1 Turn off the computer 2 Insert the adapter into the available PCI slot 3
10. stics gt item to run the adapter test program Adapter test program includes lt Run EEPROM Test gt lt Run Diagnostics on Board gt lt Run Diagnostics on Network gt and lt Run Power Management Test gt The lt Power Management Test is available for WOL adapter only After choosing the lt Run Diagnostics on Board gt item the screen will display like O sabl ed Pass Court Fail Count A 1 0 Register B 100Mbps Loopback C 10Mbps Loopback D Gb e Comnecti on lt Cable Connection gt test reminds you that the connection link might be fail either the cable is not connected or the cable link fails For the lt Run Diagnostics on Networks test it is necessary to connect your computer with its supporting hub or another computer This is a Ping Pong test This test cannot be completed except two computers on the LANfor sending or receiv ing the test packets between computers For the lt Run Diagnostics On Network gt test Ethernet Address Ethernet Address 00E07DC00002 00E07DC00001 Target Machine Master Machine Network Master Machine Master machine sends magic packet or Wake up frame through the network Target Machine Target machine is notified whenever a qualified wakeup packet is received To wake up Target Machine with Magic Packet Step1 Target Machine Target Machine is necessary to use the WOL cable link the Wake On LAN connector on adapter with your motherboard Check BIOS lt POWER MANGEM
Download Pdf Manuals
Related Search