Operating Instructions for Electronic Lock E6000 with Opening Delay
Contents
1. SECU GmbH Wormgermthle D 58540 Meinerzhagen Tel 02358 905280 PCU Sicherheitsorodukte GmbH NUMBER LOCK WITH 111 MILLION GENUINE SETTING CONFIGURATIONS Operating Instructions for Electronic Lock E6000 with Opening Delay Electronic lock E6000 allows you to either set the lock for immediate access after entering the correct numerical code or for delayed access after a pre set waiting period KEYING IN THE NUMERICAL CODE In this instruction you are requested to key in a numerical code several times Please turn the dial until you see the first digid at the illuminated display Press ENTER key Turn the dial again until you see the second digid Press ENTER key After the last digid turn the dial until you see the sign gt and continue with the following instructions OPENING THE SAFE OR STRONGROOM Press EIN ON key After a short high pitched signal tone key in the numerical code factory setting 1 23 4 5 6 Press ENTER key you will hear the short high pitched signal tone again A short low pitched signal tone indicates that you entered the wrong code If the opening delay is set to 0 zero minutes factory setting please proceed with step 6 Wait for the set opening delay to lapse During the waiting time the safe cannot be opened The end of the opening delay is indicated by short high pitched signal tones lasting 30 seconds Press ENTER key before the sounding of the signal tones ceases and re enter t2. code and press the ENTER key It should now be possible to open the lock by turning the lock handle half a turn CHANGING THE OPENING DELAY Press the EIN ON key Key in the numerical code If you have selected an opening delay of 0 minutes proceed with step 4 Press the ENTER key once and wait for the opening delay to lapse Following that press the ENTER key once more whilst the short high pitched signal tones are sounding Now enter your numerical code once more Hold the ENTER key pressed down 6 seconds until you hear a long high pitched signal tone Key in the two figure number 60 Press ENTER key Enter the new opening delay of your choice by keying in any two figure number between 00 and 99 This entered number is the opening delay in minutes Press ENTER key If you have performed the coding process correctly you will hear 2 long high pitched signal tones The sounding of two long low pitched tones indicates that you made a mistake entering the numerical code Please start over at 1 Entering an opening delay of 00 implies that the safe or strongroom is to be operated without delay in other words the first entry of the correct numerical code factory setting will open the lock page 3
3. he valid numerical code Complete by pressing the ENTER key Open the lock by the lock handle by turning it a half turn The electronics will switch itself off automatically after 5 seconds Now open the door by turning the door handle SECURING THE SAFE OR STRONGROOM If it should only be possible to open the safe or strongroom by entering the numerical code the door and lock handles have to be turned back in their original position first lock the door then the lock LOCKING THE SAFE OR STRONGROOM The safe or strongroom is locked by turning the door handle It can then be opened without re entering of the numerical code REMARKS After keying in a wrong number the number combination can be deleted by pressing the EIN ON key After that the opening procedure can be repeated page Subject to technical modifications 6000 Standard Betriebsanleitung englisch p65 Date 02 01 After keying in the wrong number combination three times in a row the electronic system blocks the safe for five minutes Following that the electronic system blocks the safe for a further twenty minutes ifthe entered number is wrong again manipulation security During this waiting time the safe cannot be opened even if the correct combination is keyed in The end of the blocking time is indicated by two short high pitched signal tones If more than 30 seconds lapse between keying in two numbers the electronic system will switch itself off for
4. ronic lock has discovered a defect Please contact the safe service department even if the electronic system continues to operate perfectly CHANGING THE NUMERICAL CODE WHEN CHANGING THE NUMERICAL CODE MAKE SURE THE DOOR IS OPEN AND BLOCKED DO NOT ENTER PERSONAL DATA such as your birthday If the set numerical code is lost it is impossible to open the safe or strongroom Therefore DO NOT FORGET THE NEW NUMERICAL CODE KEEP IT IN A SAFE PLACE Press the EIN ON key Key in the old numerical code If you have selected an opening delay of 0 minutes proceed with step 4 Press the ENTER key once and wait for the opening delay to lapse Following that press the ENTER key once more whilst the short high piched signal tones are sounding Now enter your old numerical code once more page 2 Hold the ENTER key pressed down 6 seconds until you hear a long high pitched signal tone Now key in your new combination of 6 to 8 figures e g 2 4 73 5 8 Press ENTER key Key in the new combination once more Press ENTER key If you have performed the coding process correctly you will hear 2 long high pitched signal tones The sounding of two long low pitched tones indicates that you made a mistake entering the numerical code Please start over at 1 TEST TO BE CARRIED OUT WITHOUT FAIL It should not be possible to turn the lock handle half a turn with the door open and blocked Press the EIN ON key key in the new numerical
5. security reasons The opening or number coding process will then have to repeated from the beginning The stored data are not lost in the event of a power failure REPLACING THE BATTERIES If after switching on the electronics there is a signal of 3 x long low pitched tones the batteries have to be replaced There is still sufficient energy left to open the safe another fifty times approx imately The numerical code cannot be changed as long as the batteries are running low To replace the batteries enter a screwdriver in the top and bottom side slots and lift offthe top and bottom cover plates J Insert four leakproof batteries type Mignon LR 6 alkaline AA type batteries Make sure the old batteries are disposed of in an environmentally safe manner LIST OF THE VARIOUS SIGNAL TONES High pitched tones 1 x short EIN ON key pressed or bolt mechanism unblocked 2 x short End of blocked status 1 x long ENTER key pressed for six seconds start of coding mode 2x long Coding process completed correctly Low pitched tones 1 x short The entered code is wrong 2 x short EIN ON key pressed while blocked 1 x long This signal sounds after entering the correct numerical code after the lock has been manipulated blocked status 2x long Coding process incorrectly performed The old code remains valid 3xlong The batteries have to be replaced 6xlong The fault detection routine of the elect
Download Pdf Manuals
Related Search