hawos Easy Operating instructions
Contents
1. hawos Strong Mills Fine Flour hawos Kornm hlen GmbH Ober Eschbacher StraBe 37 D 61352 Bad Homburg v d H Germany Tel 49 0 6172 40120 0 Fax 49 0 6172 40120 19 info hawos de www hawos de _GB y__ 10 12 2009 GA_Eas2. Operating instructions hawos Easy Congratet ations i mt on purchasing your hamos Hour mul LZ gt bb D Bb gt Bb gt ATTENTION Safety is paramount Only connect your mill to a properly installed socket with earthing contact Do not use defective units If the mains cord is damaged only the manufacturer its customer service department or a qualified professional may replace it Only authorised hawos professionals may perform repairs Never operate your mill unattended Never reach into the funnel or flour outlet when the unit is operating risk of injury Before opening the housing be absolutely sure to pull the mains plug to prevent the unit from accidentally activating risk of injury This device is not intended for use by persons including children with impaired physical sensory or mental abilities or who lack Adjusting wheel top Fixed grindstone _ _ _ Grinding chamber _ On Off switch Safety is paramount experience and or knowledge unless they are supervised by a person responsible for their safety or have been instructed by such a person in how to use the device Children must be under supervision to ensure that they do not play with the device A Never immerse the device in water hawos flour mills are equipped with an overcur rent circuit breaker that protects the motor from excessive current consumption e g if debris jams the grindstone
3. e If necessary open the grinder and remove any leftover flour and or debris If the grindstones are heavily laden clean them with a dry hard brush for this see the section Opening the grinder The flour fineness setting changes by itself The adjusting wheel setting changes while in use Solution e Tighten the brake screw on the side opposite the adjusting wheel so that the wheel bracket can be adjusted easily but the setting does not change by itself The rubber ring may only press up against itself slightly figure 7 Opening the grinder Figure 4 With a screwdriver remove the brake screw on the housing side opposite the adjusting wheel Figure 5 Pull the adjusting wheel together with its axle out of the side Figure 6 Remove the funnel insert Figure 7 Screw the brake screw back in adjust the play of the adjusting wheel Opening the grinder AX Attention Turn off the mill with the On Off switch and then disconnect the mains plug before opening the housing to prevent the device from accidentally turning on risk of injury A microswitch will prevent the device from accidentally activating if the funnel insert is not in place e Unscrew the brake screw on the side opposite the adjusting wheel figure 4 e By means of gently turning the adjusting wheel remove it together with the axle figure 5 e Take out the funnel insert fi
4. P 2 Milling Once connected to a power supply your hawos mill is ready for use Figure 1 Turn the adjusting wheel to set the fineness Place a bowl under the flour outlet and adjust the fineness as desired figures 1 3 Then fill the funnel with grain and turn on the mill m Figure 2 3 Turning the adjusting wheel will lift and lower the funnel insert Ti Start up 5 Setting the fineness You can steplessly set the fineness of the mill feed from coarse to fine with the adjusting wheel When you turn the wheel towards fine the funnel insert will lower When changing the setting from coarse to fine the mill should either be on or the grinder must be empty The different types of grain and other mill feed differ considerably with respect to their fat and fibre content endosperms etc Our table Suitable mill Suitable mill feed Wheat Rye Spelt Barley Oats Millet Sweet corn Durum wheat Brown rice not parboiled rice Buckwheat Green spelt Flax seed mix 1 1 with wheat Chick peas Green peas Nutritional yeast Quinoa Amaranth feed is based on this hawos mills have undergone extensive testing and this table was compiled accordingly for your reference The finer you grind the more probable clogging of the grindstones becomes Pay attention to the milling noise If it diminishes considerably then the grind
5. carefully read through the safety instructions and operating instructions Only in this way will you be able to use all functions safely and reliably Hold onto these operating instructions for future reference Pass these operating instructions on to any subsequent user of the product 1 Mill feed Please only use clean and dry grains You can determine this if the seed crackles distinctly when you crush it against a hard surface with a spoon Wet grain can be crushed and then looks like an oat flake Consult the list Suitable mill feed on page 5 when adjusting the fineness Please only mill sweet corn for grinding corn Only process mill feed with the device once 2 Power supply Only connect the mill to an alternating current source Check whether the existing mains voltage corresponds to the voltage specified on the base plate 3 Location The mill housing is made of wood Wood is a living material that is affected by changes in temperature and humidity which may cause it to crack You can best protect and care for the housing by not placing the mill close to radiators and not placing it right next to a stove steam moisture 4 Setting up the mill A During use place the flour mill on a hard level base kitchen countertop The slots on the bottom of the device may not be obstructed so that the motor can be ventilated Start up Please first read the section Before first use P 3 and the safety notes
6. funnel inserted properly microswitch Solution e Check and rectify any defect The motor hums but doesn t start running When turning off the unit grain may have clogged between the grindstones and may have jammed them Solution e Turn the adjusting wheel to coarse with the motor turned on until the milling process starts again e Slowly turn the wheel back to fine page 4 figures 1 3 The mill is on but no flour is emitted If the grain is too wet or e g if spelt and oats are ground too finely the grindstones may be smeared Solution e Mill approximately 100 g brown rice semi coarse setting e If necessary open the grinder and remove any leftovers see the section Opening the grinder for this The mill turns off while in use Debris or clogged grindstones may cause the mill come to a standstill In such a case the overcurrent circuit breaker automatically deactivates the mill after approximately 20 seconds Solution e Remove any debris and or after the mill has cooled off mill approximately 100 g brown rice semi coarse setting The adjusting wheel cannot be turned to the fine setting If an overfilled flour bowl causes e g the flour to back up this may jam the grinder There is leftover grain or debris in the grinder Solution e When the mill is running turn to the adjusting wheel to the coarse setting and allow the grinder to run without any mill feed
7. gure 6 In order to subsequently reassemble the mill reverse the steps e Install the filter insert e Insert the adjusting wheel axle through the side opening e Screw in the brake screw on the other side Adjust the play of the adjusting wheel with the brake screw the rubber ring may only press up against itself slightly figure 7 Technical data Model Easy Housing Beech Multiplex Funnel fill volume 560 g wheat Base dimensions L x W mm Height mm 150 x 150 330 Grinding capacity for wheat Approximately 100 g min Mill Corundum ceramic grindstone horizontally positioned 70 mm Weight 7 9 kg Motor output 360 watts 230 volts 50 Hz Warranty 10 years The mill is conceived and designed for private household use The device is intended for grinding the mill feed listed on page 5 Any other use is deemed improper hawos assumes no liability for cases of improper use hawos Service If you have guestions about your mill please give us a call or write us an e mail our customer service At the end of its lifecycle this product must be turned in at a collection point for recycling electric and electronic appliances The materials can be reused as labelled Please contact your community or city administration for the respective collection point team is happy to assist you Tel 49 0 6172 401200 e E mail info hawos de
8. s In addition to the afore mentioned overload safety switch the motor is also equipped with a overheating protection which deactivates the mill in the event of an overload If this occurs set the On Off switch to Off Once your hawos mill has cooled off you can use it again Funnel bottom Rotating _ _____ grindstone Flour outlet Before first use Dear mill owner Weare delighted that you have decided on the flour mill from hawos Your hawos will serve you well in preparing your natural food cuisine for many years to come Please observe the following notes before using it for the first time Please carefully read through these operating instructions to familiarise yourself with your hawos It will reward you with reliability and convenience Proper use The mill is conceived and designed for private household use The device is intended for grinding the foods listed on page 5 Product contents Mill funnel lid Brief instructions e Connect to a properly installed socket with earthing contact e Place the flour bowl under the flour outlet e Set the fineness with the adjusting wheel e Add the flour to the funnel e Turn the device on correct the fineness as needed e After milling turn the device off e Only use the flour mill for grinding food A table of edible mill feed is provided on page 5 Before first use Before you use the device for the first time please first
9. stones are starting to clog Set the adjusting wheel to coarser Turn off the mill once all mill feed has been processed Feel free to also try foods that can be rolled and those that can be poured that are not indicated on the adjacent table e g dry spices Proceed with care when trying new types and let us know about your results We are always delighted to learn more Oilseeds jam the grinder due to their high fat content For this reason mix mill feed with high fat content 1 1 with wheat or another grain 6 Cleaning Faults Cleaning A brush is integrated in the bottom rotating grindstone of your hawos which sweeps out the flour with every rotation thereby automatically cleaning the mill If you don t intend to use your mill for a prolonged period of time we recommend cleaning any leftover flour out of the grinder This is very easy with a vacuum cleaner Set the adjusting wheel to coarse and then insert the vacuum cleaner nozzle into the funnel and flour outlet of the mill when it is activated I Do not in any case clean the housing with abrasive cleaners Never immerse the unit in water If necessary clean the housing with a damp cloth and then rub in a small amount of vegetable oil to preserve the surface Faults In the unlikely event of a fault you can rectify it easily The motor doesn t start Is the mill connected to a power supply Has the plug been properly connected with a socket Is the
Download Pdf Manuals
Related Search