Operating Instructions System Manual Audio -
Contents
1. Systemprog button By pressing the Systemprog button for 3 s the door com munication system is switched into the programming mode The yellow LED next to the programming button indicates the active programming mode via flashing see Page 19 T r ffnerprogr button The T r ffnerprogr button has two functions 1 Activating door opener programming mode If the T r ffnerprogr button is pressed for 3 seconds while the system is in programming mode the door opener programming mode is activated see Page 23 The yellow LED next to the T r ffnerprogr button indicates the active door opener programming mode via flashing 2 Actuation of the connected door opener Briefly pressing the T r ffnerprogr button activates the door opener for the set time T r ffnerzeit The yellow LED next to the T r ffnerprogr button illuminates during the switching time T r ffnerzeit adjuster The activation time of the door opener is set at the T r ffn erzeit adjuster The setting time lies in the range 1 second to 10 seconds The potentiometer can be adjusted with a screw driver with a 3 mm blade Betrieb indicator During trouble free normal operation only the green Betrieb LED illuminates It indicates that the device is being supplied with power Uberlast indicator The audio control device is equipped with an electronic over oad protection which protects the electr2. DPI a Systemprogr H You can implement the so called internal call function with the optional call button for home stations A voice connection between two home stations can be established via the internal call To assign the call button of a home station to another home station e g in the hobby room proceed as follows 1 Press the Systemprog button on the control device for 3 seconds to start programming mode see Page 19 2 Press the call button on home station 1 for 3 seconds until you hear a short acknowledgement tone Y You will hear a long acknowledgement tone i Releasing the button after 3 seconds If the button press is not ended after the first acknowledge ment tone all assignments of the respective door home sta tion will be deleted after an additional 3 seconds 3 Press the Q button on home station 2 for 3 seconds until you hear a short acknowledgement tone v A long acknowledgement tone indicates successful assignment Three short acknowledgement tones indicate faulty assignment The memory of the home station may already be occupied A maximum of 10 call buttons can be assigned to a home station a maximum of 15 call buttons to a surface mounted hand free feature home station 4 Press the Systemprog button on the control device to exit the programming mode 5 Carry out a function test Deleting all assignments to a home station A home station which as already
3. 38 2 Press the call button on the door station for 3 seconds M Meier oO until you hear a short acknowledgement tone D A Y You will hear a long acknowledgement tone D Releasing the button after 3 seconds If the button press is not ended after the first acknowledge ment tone all assignments of the respective door home station will be deleted after an additional 3 seconds until you hear a short acknowledgement tone 3slola 3 Press the A button on the home station for 3 seconds S Y A long acknowledgement tone indicates successful gt s assignment Three short acknowledgement tones indicate faulty assignment The memory of the home station may already be occupied A maximum of 10 call buttons can be assigned to a home station a maximum of 15 call buttons to a surface mounted hand free feature home station ystemprogr 1x10 Asysemprasey 4 Press the Systemprog button on the control device to We U exit the programming mode 5 Carry out a function test 20 House divided into several flats Assigning door station call buttons to home stations 5 VV 3 Ss DOs Systemprogr a ee D iot o To assign the door station call buttons to the respective home stations please proceed as follows 1 Press the Systemprog button on the control device for 3 seconds to start programming mode see Page 19 2 Press the cal
4. 3 seconds to start programming mode see Page 19 6s 3 Press any call button on the door station for 6 seconds to M Meier A delete the existing assignments 38 4 Press all call buttons on the door station one after another M Meier SS in the sequence of the first start up for 3 seconds to d restore the assignments Y The replacement and the old assignment of call buttons is restored stations with this No further programming at the home is necessary 1 5 Press the Systemprog button on the control device to 1x o Systemprogr E e Be exit the programming mode 6 Carry ou If the cal a function test buttons were assigned in the wrong order repeat the procedure and press the call buttons in the reverse order Replacement of a door communication bus coupler When replacing a door communication bus coupler the sys tem must be restarted e access to the home station the floor call button is required 33 LED indicators on BUS devices The LEDs of the hands free feature Comfort with receiver surface mounted hands free feature and surface mounted gong home stations indicate the system status LED button System status or A Programming mode active call buttons and or flashes gong not yet assigned or Al Programming mode active at least one call lights up button is already assigned to the home station or he gong Programming mode active home station lights
5. 7 1x LO Esystemprasey 4 Press the Systemprog button on the control device to FS U exit the programming mode 27 Assigning several home stations to a call button 3s 3s 28 5 1 DE Systemprogr EE ee D Systemprogr S e 4 If several home stations are to be called simultaneously when a door station call button is pressed a call button can be assigned to several home stations as follows 1 Press the Systemprog button on the control device for 3 seconds to start programming mode see Page 19 2 Press the call button to which the home stations are to be assigned at the door station for 3 seconds until you hear a short acknowledgement tone Y You will hear a long acknowledgement tone 3 Go to the first home station Press the G button for 3 seconds until you hear a short acknowledgement tone Y A long acknowledgement tone indicates successful assignment 4 Go to the door station and press the call button again for 3 seconds 5 Go to the second parallel home station Press the amp button for 3 seconds until you hear a short acknowledgement tone Y Along acknowledgement tone indicates successful assignment 6 Repeat Steps 4 and 5 to assign an additional parallel home station to the call button 7 Press the Systemprog button on the control device to exit the programming mode 8 Carry out a funct
6. home station memory is already occupied by 10 15 call buttons In this case the O LED of the hands free feature surface mounted hands free feature and Comfort with receiver home station lights up A maximum of 10 call buttons can be assigned to a home station a maximum of 15 call buttons to a surface mounted hands free feature home station e no call buttons at the door or home station were pressed beforehand e all previously pressed call buttons were already assigned to other home stations 35 Table for start up documentation Call button Number Name Home station Name Location Floor Taught in Meier 24 floor left living room Y 36 Call button Number Name Home station Name Location Floor Taught in 37 Acceptance of guarantee 38 The warranty is provided in accordance with statutory require ments via the specialist trade Please submit or send faulty devices postage paid together with an error description to your responsible salesperson spe cialist trade installation company electrical specialist trade They will forward the devices to the Gira Service Center 39 Gira Giersiepen GmbH amp Co KG Elektro Installations Systeme Postfach 1220 42461 Radevormwald Deutschland Tel 49 0 21 95 602 0 Fax 49 0 21 95 602 191 www gir
7. programming mode see Page 19 2 Press the T r ffnerprogr button on the control device for 6 seconds to delete all of the assignments from the control device to the door stations The LED starts flashing after 3 seconds Keep the button pressed for an additional 3 seconds until the LED next to the programming button T r ffnerprogr flashes rapidly exit the programming mode connected at the switching actuator and the door station pro ceed as follows 6s ES Progr A EI a 1x10 Systemprogr is ESE EM H Press the Systemprog button on the control device for 3 seconds to start programming mode see Page 19 Press the Prog button on the switching actuator for 6 seconds to delete all of the assignments from the switching actuator to the door stations The LED starts flashing after 3 seconds Keep the button pressed for an additional 3 seconds until the LED next to the programming button Prog flashes rapidly 3 Press the Systemprog button on the control device to exit the programming mode Replacement of defective call station button top units of a flush mounted door You can replace defective door station call button top units at a flush mounted door station without having to reprogram all assignments 1 Replace all defective call button top units with new ones 3 e NE 2 Press the Systemprog button on the control device for A QU
8. Gira door communication system is switched to program ming mode for start up 1 Press the Systemprog button on the control device for 3 seconds Y The yellow LED next to the programming button flashes flash frequency 1 Hz after the button is pressed and indicates the active programming mode The system is now in programming mode for approx 7 minutes Each time the start up button is pressed on a door or home station the time is reset to approx 7 minutes D LED indicators on BUS devices The active programming mode is also signalled by the LED of various BUS devices such as the hands free feature home station the Comfort home station with receiver or the sur face mounted hands free feature home station An overview of the LED indication is found on Page 34 Exiting programming mode 1 Briefly press the Systemprog button on the control device to exit the programming mode Y The yellow LED goes out Start up documentation For documentation on the home stations assigned to the call buttons please see the table on Page 36 There you enter the names homes in the sequence in which you will allocate the home stations later on One family house Assigning door station call button to home station To assign a door station call button to a home station proceed as follows 3 sie Raina 1 Press the Systemprog button on the control device for 3 seconds to start programming mode see Page 19 D
9. Operating Instructions System Manual Audio control device 1287 0 GIRA Table of contents System informa UoN s ses EEE LA RAE cd 4 Installation scenario TOpOlOGIS siei a et ie 6 Structure Greet STEET Sursee erregen en 8 Str cture OT a HOME staton s esere eenaa cere ta add genen 0 The door communication DUS coupler cccoccnnnocococnnccnconononononononnnnnnnnnnnonnnnnnnnonnnnnons 2 The auUdio COntrol Gevie ces he nase angesehen 4 Displays and operating elements of audio control device snee 5 Connection terminals of audio control device Mounting of audio control device oooonoococnnoccccccoooncononannconnonononnnnnnnn nana nnnnnnnnnn rca Technical data of audio control device en Start up Switching system to programming mode cocccnocccoccccoonccconcconnc cnn nacnn nc conn nc na na nannccanns 9 One family house Assigning door station call button to home station 20 House divided into several flats Assigning door station call buttons to Wel EE Assigning door opener Automatic door opene Assigning home station via floor call button 27 Assigning several home stations to a call button 28 Assigning several home stations to a floor call button 29 Assigning call button for home station to a home station internal call 30 Deleting all assignments to a home station 31 Deleting assignment of the door opener enemeeneennemennnnen 32 Replacement of de
10. a de info gira de GIRA 10 41 05 21 19 11
11. al values e g very low ohm or 24 V can be connected to the relay con tact with an additional power supply DOIDO 230 vac Mounting of audio control device A Attention Installation and mounting of electrical devices may only be carried out by a qualified electrician For installation protected from dripping and sprayed water mount the control device to a top hat rail in the distribution The mains and bus connection is made via screw terminals The mains connection must be made via an all pole mains switch with at least a 3 mm contact opening The ventilation slits of the control device must not be blocked Technical data of audio control device Primary rated voltage AC 230 V 50 Hz Secondary rated voltage SELV 26 V DC 2 V Secondary rated current 160 mA continuous load Overload deactivation from approx 350 mA 550 mA peak load max 5 seconds Power 47 VA Protection type IP 20 Screw terminals 0 6 mm to 2 5 mm door opener output 12VAC 1 6A Power on time 25 max 10 seconds ON door opener then 30 seconds OFF Contact load capacity relay output 30VAC 2A Door opener time adjustable 1 to 10 seconds Operating temperature 5 C to 45 C Dimensions 6 modules series inst housing Switching system to programming mode 350 SST g Systemprogr D SET a Systemprogr H The
12. been assigned is deleted as follows Nu 7 1 Press the Systemprog button on the control device for 3 s OS Systemprogr em me 3 seconds to start programming mode see Page 19 D 6 eh 2 Press the Q button on the home station for which the assignment is to be deleted for 6 seconds You will hear a brief acknowledgement tone after 3 seconds Hold down the button for another 3 seconds until you hear a long acknowledgement tone N A SE Y The long acknowledgement tone confirms the successful deletion var 3 Press the Systemprog button on the control device to exit the programming mode e 1 Deletion only possible directly Deleting the assignment of a call button to a home station is not possible via the floor call button The deletion of the assignment can only occur via the Q button of the home station 31 Deleting assignment of door opener Door opener at audio control device To delete an existing assignment between the door opener connected at the control device and the door station proceed as follows ESF pl 7 3s S os Systemprogr ES nn we ee 6s SR r ffnerprogr i en Y VENDA a 1x O Systemprogr ee Ee y Door opener at switching actuator To delete an existing assignment between the door opene 3 Press the Systemprog button on the control device to Press the Systemprog button on the control device for 3 seconds to start
13. cknowledgement tone indicates successful assignment 6 After you have assigned all the home stations press the Systemprog button on the control device to exit programming mode 7 Carry out a function test D Maximum number of call buttons per step Up to 20 call buttons can be temporarily stored per step If more than 20 call buttons are to be assigned the first 20 call buttons must first be pressed and then assigned to the home stations The remaining call buttons can then be assigned Assigning door opener f 3s E a Systemprogr 1 ta e z 2 3s DE Se oC e e 2 3 S M Meier a D A 1x O PN r ttnerprogr ES EE A EE g 1x10 Systemprogr BS REN A The door opener connected to the control device is assigned to the main door station It is activated if the O button ata home station is pressed spontaneously even without any pre vious conversation The door opener of a back side door is connected to the switching actuator It can be activated via the button if a door call was previously initiated from the door station of a back side door It is switched to the main door 2 minutes after the door call or 30 seconds after the door call Assigning door opener of main door The door opener connected to the control device is pro grammed at the respective door station as follows Press the Systemprog button on the control device for 3 s
14. ds after the door call is triggered If several door stations are present in the system the automatic function automatically acts on the door opener of the door station from which the door call was triggered Before use the automatic door opener must first be enabled Enabling disabling automatic door opener function 1 Press the Systemprog button on the control device for 3 seconds to start programming mode see Page 19 2 Simultaneously press the buttons X and lt O on the home station for approx 3 seconds By pressing these buttons you can switch over the status of the automatic door opener enabled or disabled Y Ifthe gt LED lights up long for confirmation the automatic door opener function is enabled If the D LED lights up short for confirmation the automatic door opener function is disabled 3 Press the Systemprog button on the control device to exit the programming mode 25 26 If the automatic door opener function is enabled you can activate the automatic door opener as necessary on the home station as follows Activating automatic door opener 1 Simultaneously press the buttons X and O on the home station for approx 3 seconds to activate the automatic door opener vd When the automatic door opener is activated the LED O lights up continuously The door opener is automatically operated after a door station call button is pressed Deactivating automatic door
15. econds to start programming mode see Page 19 Press the T r ffnerprogr button on the control device or 3 seconds to start the door opener programming mode Y The LED next to the T r ffnerprogr button flashes 3 Press any call button on the door station for 3 seconds until you hear a short acknowledgement tone Y A long acknowledgement tone confirms successful assignment In addition the door opener connected to the control device is operated for the set time To assign additional door stations to the door opener maxi mum of 3 repeat Step 3 on the next door station 4 Press the T r ffnerprogr button on the control device to exit door opener programming mode 5 Press the Systemprog button on the control device to exit the programming mode 23 1 3 Ss Ess Systemprogr T me 3s EES Progr H M Meier SAN 2 1x1 EES Progr Ka 1x o Systemprogr iS See H Assigning door opener of a side back door The door opener connected to the switching actuator is pro grammed at the respective door station as follows Press the Systemprog button on the control device for 3 seconds to start programming mode see Page 19 7 2 Briefly press the Function button on the switching actuator several times until the Door opener LED lashes w Press the Prog button on the switching actuator for 3 seconds until the yellow LED next to the Prog button lashes 4 P
16. f the Gira door communication system The audio control device assumes the following tasks in the Gira door communication system e provision of the bus voltage 26 V DC 2 V for the door communication system e power supply of call button illumination max 15 the number of call button illuminations that can be supplied is dependent on the system size and the number of home stations operation in parallel e provision of door opener control including power supply 12 VAC 1 6 A of the door opener e power supply of a TC gateway e activation of the programming mode from the entire door communication bus system Additional product features of the control device e maximum of 70 devices e g 1 built in speaker with 5 add on modules 68 surface mounted home stations e depending on the system size up to 3 home stations can be operated e electronic overload and short circuit protection e electronic excess temperature protection e overload short circuit LED indicator e LED operation indication for determination of whether or not mains voltage is active e adjustable activation time of door opener Displays and operating elements of audio control device UOUUODUUUDUUUUDUUUUU GIRA T rkommunikations System Steuerger t Audio Systemprogr Betrieb oo O 1287 00 N 230V 50H2 47VA L gus 28V gt 2V 12V 1 8A ED25 ra KR zn Be ae OO 9 10
17. fective call button top units of a flush mounted le EE 33 LEDindicators On GEELEN 34 Acknowledgement tones of Bus devices ern n 35 Table for start up documentation 36 eelere ge ET EE 38 System information The Gira door communication system operates with the volt age type SELV With the audio control device systems with up to 70 audio devices can be realised in certain systems e g 1 built in speaker with 5 add on modules and 68 surface mounted hands free feature home stations Depending on the system size a maximum of 3 home stations can be operated in parallel per call button D Planning software An exact determination of the maximum system size is possi ble with the planning software at www gira de A call tone differentiation is made between the following calls at the home stations e door call initiated by call button e floor call initiated by floor call button e internal call initiated by call button for home stations Cabling and cable arrangement Cables with a wire diameter of 0 6 or 0 8 mm can be used as bus lines The following cable types are suitable for use as bus lines e J Y ST Y communication line e YR insulated bell wiring e A 2Y L 2Y communication cable Cable lengths for audio components The maximum total cable length distributed among several wiring sections is 700 m A maximum of 30 devices may be connected to each wiring section The maximum cable lengths of the individ
18. fitted at a later time Structure of a flush mounted door station The basic structure of a flush mounted door station is pre sented in the example of the flush mounted door station with 3 gang call button PwMN al o escote e ooooo TT A Door communication bus coupler Audio connection cable Speech insert TX_44 cover frame bottom section not in scope of supply Door speaker top unit TX_44 cover frame top section not in scope of supply Call button cover plates 3 gang call button Structure of a surface mounted door station The basic structure of a surface mounted door station is pre sented in the example of the surface mounted door station with 3 gang call button 1 2345 6 7 8 Neo ja Y 0000 o e 2 00000 O 0 0000 O0 9 0 Q 0000 Housing bottom section 3 gang call button Speech cover plate Cable inlet Sealing ring Connection terminals Housing top section Call button cover plates 0 JO Oo PWNMN Structure of a flush mounted home station The basic structure of a flush mounted home station is pre sented in the example of the Comfort home statio
19. ion test Assigning several home stations to a floor call button If several home stations are to be called simultaneously when a floor call button is pressed a floor call button can be assigned to several home stations as follows 3 s PE 1 Press the Systemprog button on the control device for ES ystemprogr R GC Que A 3 seconds to start programming mode see Page 19 for 6 seconds You will hear a brief acknowledgement tone after 3 seconds Hold down the button for another 3 seconds until you hear a long acknowledgement tone 6 9 2 Press the floor call button connected to home station 1 you hear a short acknowledgement tone 2el A o 3 Press the D button on home station 2 for 3 seconds until E v A successful teach in is confirmed by a long acknowledgement tone at home station 2 To assign an additional home station repeat the procedure from Step 2 ystemprogr 1x rs 1 4 Briefly press the Systemprog button on the control Qe nn device to exit the programming mode 5 Carry out a function test All assigned home stations ring when the floor call button is pressed A Do not connect floor call button in parallel A floor call button may not be connected to several home stations in parallel 29 Assigning call buttons for home station to a home station internal call 3s 3s 3s 30 Se ES Systemprogr N O Hobbyraum o ZT
20. l buttons on the door station for 3 seconds until you hear a short acknowledgement tone Important Press the call buttons in the sequence in which the home stations will be assigned later Y You will hear a long acknowledgement tone D Releasing the button after 3 seconds If the button press is not ended after the first acknowledge ment tone all assignments of the respective door home station will be deleted after an additional 3 seconds 3 Go to the home station whose call button is the first one you pressed at the door station Press the G button on this home station for 3 seconds until you hear a short acknowledgement tone Y A long acknowledgement tone indicates successful assignment Three short acknowledgement tones indicate faulty assignment The memory of the home station may already be occupied A maximum of 10 call buttons can be assigned to a home station a maximum of 15 call buttons to a surface mounted hand free feature home station 21 22 a 1 Systemprogr H 4 Go to the home station whose call button is the second one you pressed at the door station Press the G button on this home station for 3 seconds until you hear a short acknowledgement tone Y A long acknowledgement tone indicates successful assignment 5 Go to the other home stations and press the 8 button there for 3 seconds until you hear a short acknowledgement tone Y Along a
21. n with receiver 4 5 6 7 8 3 2 Receiver insert Empty insert Audio connection cable Door communication bus coupler Cover frame not included in scope of supply Operating buttons Receiver mount Receiver Receiver mount with cable branch O Receiver cable Zoo JO OO PwWNMN Structure of the surface mounted hands free feature home station The structure of the surface mounted hands free feature home station is shown in the following example 1 2 3 4 5 6 Mounting plate Fixing holes for wall mounting 2 gang cover frame without crossbar cover frame not included in scope of supply frameless installation only possible with wall mounting Fixing holes for box mounting Housing top section Operating buttons Door communication bus coupler BUS Video System System ro zv ET The flush mounted versions of the door and home stations are connected to the 2 wire bus via door communication bus cou plers The bus coupler has the following connections BUS The devices are connected to the 2 wire bus via the BUS ter minals Polarity need not be taken into account during connec tion as the polarity of the door communication bus is neutral Floor call button ET With home stations any push button NO co
22. ntact can be con nected to the ET terminals as the floor call button With the door stations for example a mechanical bell button NO contact can be connected This then acts like a call but ton from the Gira door communication system during start up and later operation The maximum cable length between the mechanical button and the door communication bus coupler is 20 m Additional supply ZV The ZV terminals have two functions 1 Power supply of call button illumination at the door stations The call buttons are constantly illuminated at the door stations If the call button illumination is to be switched off permanently the jumpers between the bus and ZV terminal must be removed 2 Additional power supply for bus devices which can no longer be powered via the 2 wire bus D Connecting an additional power supply If an additional power supply is connected to the ZV termi nals the jumpers must be removed System The flush mounted inserts are connected to each other with the 6 pole audio connection cable via these connectors Video The door communication bus coupler is connected to the flush mounted inserts of the video devices e g TFT colour display colour camera etc via the 2 pole connector e 1 Rubber plugs in the connectors The second connectors are sealed with rubber plugs These plugs can be removed if necessary The audio control device The audio control device is the main power supply o
23. onics of the control device against short circuits and overloading on the bus line The overload protection is activated if for example the bus ine is short circuited due to an installation error or too many bus devices bus loads are connected The red Uberlast LED indicates both short circuits and over oads The flashing duration of the LED corresponds to the ime during which the bus voltage is deactivated when a fault occurs The LED then flashes for up to 20 seconds after the ault has been eliminated With a permanent overload or short circuit the bus voltage is switched off for approx 180 s after the third overload detec ion During this switch off phase the Systemprog T r ff nerprogr and Uberlast LEDs flash The LEDs then flash for up to 180 seconds after the fault has been eliminated Connection terminals of audio control device LN Mains connection terminals L and N AC 230 V 50 Hz Bus Output for powering of the Gira door communication bus with regulated direct current 26 V DC 2 V 160 mA 12 V AC The 12 V AC output is used to supply power to the door opener power consumption of the door opener is max 1 6 A or the telecommunication gateway Door opener relay Relay output for operating a door ee Zaang ap opener 8 12 V AC max 1 6 A EN Gao A door opener with other electric
24. opener 1 Simultaneously press the buttons X and O on the home station for approx 3 seconds to deactivate the automatic door opener Y The gt LED goes out The automatic door opener is no longer active D Behaviour after a power failure The enabled status of the automatic door opener is retained after a power failure In this case the automatic door opener is deactivated for security reasons and must be reactivated if necessary Assigning home station via floor call button If you cannot access the home during start up you can also assign the home station via a connected floor call button Nu 7 1 Press the Systemprog button on the control device for 3 s 0 Systemprogr 3 seconds to start programming mode see Page 19 D 38 2 Press the call button to be assigned to the home station M Meier OX on the door station for 3 seconds until you hear a short acknowledgement tone E Y You will hear a long acknowledgement tone 3 Go to the floor call button of the home station to be assigned Press the floor call button for 3 seconds until you hear a short acknowledgement tone 3s A v A long acknowledgement tone indicates successful a assignment D Only possible 1 with directly connected home station With several parallel home stations only the home station connected directly to the floor call button can be taught in via the floor call button DOTA
25. ress any call button on the door station for 3 seconds until you hear a short acknowledgement tone D Releasing the button after 3 seconds If the button press is not ended after the first acknowledge ment tone all assignments of the respective door home station will be deleted after an additional 3 seconds Y Along acknowledgement tone confirms successful assignment The door opener is controlled for the set time To assign additional door stations to the same door opener repeat Step 4 at the next door station 5 Briefly press the Prog button on the switching actuator to exit the programming mode of the switching actuator Y The LED of the Prog button goes out The LED of the last selected function here Door opener continues to flash until programming mode at the control device is exited 6 Press the Systemprog button on the control device to exit the programming mode Automatic door opener 3 GC EE a Systemprogr D i Hands free feature and Comfort home station The function automatic door opener is only supported by the hands free feature home station and the Comfort home station with receiver The automatic door opener is for example used in doctor s offices when after pressing a door station call button the door opener is to be automatically operated With the automatic door opener actived the door opener assigned to the calling door station is operated approx 4 secon
26. ual sections from the control device to the last device are dependent on the cable diameter used The guidelines for audio components are e 0 6 mm diameter 170 m e 0 8 mm diameter 300 m Installation scenario topologies Branch line solution ws 3 2 2 ET 2 ws 2 anaes 32000 SECH 08600 22222 o 00000 en esoso o0000 2 2 Er 2 WS 3 o ws2 2 WS 1 Outdoor station t L_a 2 2 Door opener ET Floor call button WS Home station Control unit audio Loop through solution ws3 2 ET 2 ws2 HA 20000 o o o o ol 20000 flo 2 o o o o 0000 ET WS3 2 o WS 2 o wei PPA WS 1 Outdoor station 2 2 ET e SS 2 Door opener ET Floor call button WS Home station Control unit audio The loop through solution has the advantage of not requir ing the installation of a video distributor should video compo nents be retro
27. up memory of occupied by 10 call buttons Occupied on the surface mounted hands free eature home station with 15 call buttons Programming mode active ights up ong automatic door opener enabled ong short short automatic door opener disabled O ights up Automatic door opener activated A Comfort home station with receiver lashes 2 min signals incoming call A Comfort home station with receiver ights up a call is in progress EN Hands free feature and surface mounted hands lashes 2 min free feature home station signals incoming call EN Hands free feature and surface mounted hands ights up free feature home station a call is in progress X ights up Call tone is deactivated 34 Acknowledgement tones of Bus devices In programming mode the following conditions are indicated using acknowledgement tones Acknowledgement Meaning tone Short tone e During assignment release button e While deleting no meaning continue to hold down button Long tone e During assignment call button was assigned successfully e While deleting release button assignment is deleted 3 short tones e During assignment call button was not assigned e Memory of door station for calling up learned in call buttons is occupied maximum of 20 call buttons e When assigning a door opener 3 door openers were already assigned a call button cannot be assigned if e the
Download Pdf Manuals
Related Search