Operating Instructions for Electronic Lock TeamLock 4
Contents
1. ENTER key an other short high pitched signal tone indicates that the TeamCard secret has been accepted a short low pitched signal tone indicates that the entered TeamCard code is invalid Three very short low pitched tones indicate card identification unsuccessful Repeat from step 4 A final long high pitched tone signifies that the required opening secrets have all been fed into the lock Ifthe programmed access delay is 0 minutes factory setting proceed with step 15 Wait for the pre entered opening delay to lapse In this condition the lock cannot be opened Following the 5 minute delay you will hear a series of short high pitched signal tones lasting 30 seconds During this time press the ENTER key to silence the signal tones Now press keys 1 3 2 4 7 and 0 Press ENTER an other short high pitched signal tone indicates that the numerical code has been accepted Hold the TeamCard in front of the reading range Press ENTER an other short high pitched signal tone indicates that the TeamCard code has been accepted The following long high pitched tone signifies that the required opening secrets have all been fed into the lock Now open the lock by the lock handle by manually turning it a half turn This should be done speedily but not in an overly hurried manner Before the handle is turned it should be in the end position You have approximately 5 seconds to turn the handle Following that the el2. an access timer page 5 TEAMLOCK4 Betriebsanleitung englisch P65
3. long high pitched tone If the lock has no pre entered opening delay proceed with point 5 below 3 Wait until the programmed opening delay has lapsed and you hear the readiness signal 1 e very short high pitched tones lasting approximately 30 seconds 4 Keyinthe secrets once more during the 30 second readiness period As soonas all required opening secrets have been entered you will hear one long high pitched tone signifying that the lock has identified the pre entered code and recognizes the valid access authorization 5 Now manually open the lock by immediately turning the lock handle a half turn and open the door by the door handle AS opening secrets you can chose up to 32 six seven or eight digit combinations In addition there are 32 storage locations for TeamCards to be used as keys The entered opening secrets are fully valid on their own standard and each gives access to the lock individually so that the total of 64 opening secrets can be assigned to 64 different users However you can also program the lock such that the authorization level of a particular opening secret is reduced to a part authorization In this case the missing portion needed to give a full authorization has to be complemented by keying in one or more additional opening secrets which each has a reduced authorization level as well By design the authorization to access the lock can be split into a maximum of 4 opening secrets The procedure for e
4. SECU GmbH Wormgermthle D 58540 Meinerzhagen Tel 02358 905280 gt r i Sicherheitsorodukte GmbH ELECTRONIC LOCK OFFERING A TOTAL CHOICE OF AT LEAST 111 000 000 GENUINE LOCKING COMBINATIONS Operating Instructions for Electronic Lock TeamLock 4 TeamLock 4 is an electronic locking system capable of managing up to 64 opening secrets These are either contained in 6 to 8 digit numerical codes or in non contact identifiable transponder fitted cards the so called TeamCards All TeamCards are one of a kind their characteristic features cannot be copied onto any other transponder units or dupli cated in any way they are genuine one of a kind keys whose identification has to be fed into the lock to activate their access authorization Access is gained either immediately or after a programmed delay by keying in one of the valid opening secrets or several interdependent opening secrets which can be entered in any order HOW TO OPEN THE SAFE Opening of the safe is prepared by opening of the lock according to the procedure below and then manually turning the door handle to open the door 1 Press the EIN ON key A short high pitched tone indicates that the lock is ready to receive the required input 2 Keyinall opening secrets one after the other Each input accepted by the lock is acknowledged by a short high pitched tone Inacknowledgment of completing the full access authorization after the last entry you will hear one
5. d outside the reading range during the valid reading time you will be informed by three very short low pitched tones Presentation of the TeamCard and subsequent entry of the secret code by means of the ENTER key may now be repeated an indefinite number of times Make sure the card is held parallel to the operating panel Please note that the lock will also respond with three very short low pitched tones if the card held in the reading zone is illegible Depending on the lock setting entering of the secret can either be completed by entering a single secret combination ifthat has previously been given full access authorization or by entering a total of up to four opening secrets in any order that have each been assigned a proportional part authorization EXAMPLE 1 of a complete opening procedure without delayed access For the purpose of this example we will assume that the full access authorization consists of a 6 digit numerical code say 132470 and a TeamCard and that the lock has a 0 minute access delay original factory setting Press EIN ON key 2 After a short high pitched signal tone press keys 1 3 2 4 7 and 0 Press ENTER key again you will hear a short high pitched signal tone indicating that the combination has been accepted a short low pitched signal tone indicates wrong combination Hold the TeamCard in front of the reading range Press ENTER key an other short high pitched signal tone in
6. dicates that the TeamCard secret has been accepted a short low pitched signal tone indicates that the entered TeamCard code is invalid Three very short low pitched tones indicate card identification unsuccessful Repeat from step 4 A final long high pitched tone signifies that the required opening secrets have all been fed into the lock Now open the lock by the lock handle by turning it a half turn This should be done speedily but not in an overly hurried manner Before the handle is turned it should be in the end position You have approximately 5 seconds to turn the handle Following that the lock electronics will automatically switch itself off After turning the lock handle open the door by turning the door handle page 2 EXAMPLE 2 of a complete opening procedure with delayed access For the purpose of this example we will assume that the full access authorization consists of a 6 digit numerical code say 132470 and a TeamCard and that the lock is set to a 5 minute access delay Press EIN ON key 2 After a short high pitched signal tone press keys 1 3 2 4 7 and 0 Press ENTER key again you will hear a short high pitched signal tone indicating that the number combination has been accepted a short low pitched signal tone indicates wrong combination If the programmed access delay is 0 minutes factory setting proceed with step 6 Hold the TeamCard in front of the reading range Press
7. ectronic system will automatically switch itself off After turning the lock handle open the door by turning the door handle CHANGING THE SECRET COMBINATION OF A USER CODE OR MASTER CODE ALWAYS CHANGE THE CODE WITH THE DOOR IN THE OPEN BLOCKED MODE AND DO NOT USE ANY PERSONAL DATES e g your birthday If the programmed numerical code is no longer available your only chance to open the safe is with an other pre entered valid opening secret Therefore DO NOT FORGET THE NEW SECRET COMBINATION KEEP IT IN A SAFE PLACE Press the EIN ON key Key in your valid 6 to 8 digit numerical code Hold the ENTER key pressed down six seconds until you hear a long high pitched tone Key in your new combination of 6 to 8 figures e g 247358 Press ENTER key Key in the new combination once more Press ENTER key If you have performed the coding process correctly you will hear two long low pitched signal tones ee a The sounding of two long low pitched tones indicates that you made a mistake entering the new numerical code The old code is still valid Please start over at 1 page 3 TEAMLOCK4 Betriebsanleitung englisch P65 TEST TO BE PERFORMED WITHOUT FAIL With the door open in the blocked mode it should not be possible to turn the lock handle ahalfturn Press the EIN ON key and key in the new numerical code Following the long high pitched tone signaling the lock s readiness for opening it should
8. f turn Low pitched tones 1 x short wrong secret combination 2 x short a key was pressed with the lock in the manipulation blocking mode please wait for the maximum 20 minute blocking time to lapse During this period it is not possible to operate the lock 3 x very short The lock has failed to read the TeamCard secret Please repeat the entry or use a different valid opening secret 1 x long Although the maximum four secret combinations were keyed in the full access authorization has not been reached Repeat the opening procedure with other secret combinations than the ones used for the first attempt 2 x long The attempt at recoding the lock has failed due to a wrong entry The old combinations remain valid 3 x long Replace batteries observing the correct poles and battery contacts 6 x long The electronic lock s automatic fault detection routine has discovered a defect Please refer the problem to SECU s service department even if the electronics seemingly continues to work perfectly Mixed tone sequences 1 low pitched tone short followed by 2 high pitched tones very short A key was pressed during the opening delay However the lock is still in the programmed opening delay mode 1 low pitched tone short followed by 3 high pitched tones very short A key was pressed with the lock in the blocked mode An attempt was made to open the lock outside the valid access period only on locks with the optional feature of
9. now be possible to open the lock by turning the handle a half turn PROGRAMMING OTHER LOCK SETTINGS All other lock settings have to be done with the lock in the master programming mode Some of these other settings are New or first assignment of additional opening secrets numerical codes and TeamCards Cancellation of already existing opening secrets Alteration of the authorization level of a previously programmed opening secret from partial to full authorization or vice versa Setting of the opening delay Identification of TeamCards These additional settings are described in detail in a separate set of MASTER PROGRAMMING INSTRUCTIONS CLOSING THE SAFE You can close the safe with the lock open by turning the door handle but that does not lock the lock The safe can be opened again without having to re enter the secret combination LOCKING THE SAFE If you want the safe to be accessible only by means of the opening secrets both the door handle and the lock handle have to be returned to their original positions first lock the door and then the lock REMARKS After keying in a wrong number the numerical code already partly entered can be deleted by pressing the EIN ON key After that you can key in the numerical code again Pressing the EIN ON key twice will delete all opening secrets entered up to this point The entire opening procedure has to be repeated After keying in a wrong combination three times in a
10. ntering an opening secret consists of two steps presentation of the secret by keying in the valid numerical code or holding the TeamCard in front of the reading range and entering the secret into the lock by pressing the ENTER key Do not wait between keying in two numbers or holding the TeamCard in front of the lock s reading zone For security page Subject to technical modifications TEAMLOCK4 Betriebsanleitung englisch P65 Date 02 01 reasons the electronic system will switch itself off after 30 seconds After that the opening procedure has to be re peated To input the secret code of a TeamCard the TeamCard has to be held directly in front of the reading range of the oper ating panel within 30 seconds from pressing the EIN ON key and for all subsequent entries The reading range is marked with a gray circle in the figure above The maxi mum reading distance is approximately 4 cm 1 2 inches from the operating panel While holding the card in the reading position briefly press the ENTER key to feed the secret into the system The positive identification of the transponder and acceptance of the opening secret are ac knowledged by a short high pitched tone After the full access authorization has been completed by the entering the required opening secrets you will again hear a long high pitched tone indicating you can turn the lock handle If the lock fails to identify a TeamCard because it was hel
11. row and entering it with the ENTER key before the lock opening procedure is successfully completed the electronic system will block the lock for five minutes Following that the electronics will block the lock for a further twenty minutes if the next number entered is wrong again manipulation security During this time it is not possible to open the lock even if the correct combination is keyed in The end of the blocking time is indicated by two short high pitched tones If the lock is unable to read a TeamCard because it is not being held exactly in the reading range this is signaled by three very short low pitched tones signifying that the lock is ready to repeat the reading operation The unsuccessful reading attempt is not considered as a wrongly entered combination and does not enter the lock into the blocked mode However with a legible TeamCard that has not been entered before and therefore fails the validity check by the lock the process is different this is considered areal attempt at entering a wrong combination which will lead to the blocking of the lock after the third attempt for security purposes The stored data secret combinations valid opening delay and the internal recording of the last 250 operating events will not be lost for a long time even if the batteries become depleted page 4 CHANGING THE BATTERIES If you hear three long low pitched tones after switching on the lock electronics it is time to replace
12. the batteries There is only enough power left in the present set of batteries to open the safe approximately 50 more times With the batteries running low se cret combinations cannot be altered To change the batteries open the top and bottom lids of the battery compartment by lifting them out with a screwdriver in the top and bottom side slots Insert four leak proof batteries type Mignon LR 6 alkaline AA type Dis pose of the old batteries in compliance with local anti pollution legislature LIST OF VARIOUS SIGNAL TONES The various lock operations are documented by the sounding of different acoustic signals There are two signal tone categories high pitched tones positive and low pitched tones negative The duration the tones are sounded can be very short approximately 0 1 second short approximately 0 5 second or long approximately 1 second The acoustic signals can also be given in series of several tones tone groups High pitched tones 1 x short EIN ON key pressed or secret combination accepted as valid 2 x short end of manipulation blocking mode 1 x long the lock has successfully entered the programming mode 2 x long successful completion of the recoding procedure 1 x short followed by 1 x long The required opening secrets have all been entered correctly the lock may be opened in the next 5 seconds by manually turning the handle a hal
Download Pdf Manuals
Related Search