Operating instructions - Basic functions of electronic
Contents
1. SECU GmbH WormgermUhle D 58540 Meinerzhagen Tel 02358 905280 apC Sicherheitsprodukte GmbH Operating instructions Basic functions of electronic lock SELO B Version 1 0 Electronic lock model SELO B allows you to open the lock either immediately after entering the valid 7 or 8 digit secret code or after expiration of a preset opening delay The lock s time functions can be set such that access is only granted at the preselected times The maximum number of codes for clearing the lock is 40 A GENERAL The opening procedure consists of two operations CLEARING and UNBLOCKING To start the opening procedure check that the input unit is in the vertical end position All accepted key strokes will produce a response on the display If the code number is keyed in by mistake return to the starting position of the lock by pressing the On Enter key and start over After entering the wrong secret code three times in a row the lock will automatically block all further entries for 5 minutes If after waiting for 5 minutes the wrong code is entered again the lock will block itself for a further 20 minutes manipulation resistance During this time the remaining delay is depicted on the display and not even the valid number code will open the lock If more than 30 seconds lapse between pressing any two keys the lock automatically switches itself off for safety reasons The opening procedure has to be started over Once2. 1 Press On Enter key When the lock is ready for operation the welcoming phrase on the display is followed after two seconds by a message prompting the operator to enter a valid code The black rectangular cursor sits blinking at the first digit of the code entry field and the capital letter M appears above the Function key By pressing the Function key the menus of the setting mode appear In this mode the symbols above keys 11 and 2 serve as operating symbols to navigate through the menu up or down The first menu to appear is Code change Use keys 1 and 2 to activate the other options on the menu Changing the administrator code factory setting 1 2 3 45 6 7 As soon as you enter the setting mode the cursor will automatically go to Code change To select press the On Enter key Next the administrator and the various users are depicted on the display with the administrator in first place To select the administrator press On Enter The lock now prompts the operator to enter the old code existing thus far Key in the old code when taking the lock into operation the first time enter the factory setting 1 2 3 45 6 7 and confirm with the On Enter key Next the lock prompts the operator to enter the new code Key in the new code and confirm by pressing On Enter As asafety feature the lock prompts the operator to enter the new code a second time Confirm once more by pressing the On Enter key The
3. Opening delay Calibrate clock Activate automatic changeover from summer to winter time Administrator functions Define number of digits of secret codes Reorganize Block user authorization for a change of code s Reset time functions Read out list of operations Display lock information page 4
4. data have been stored numerical codes time frame and user entries not even a power failure will delete them 3 lines for entering codes and Rotary handle for unblocking displaying messages the lock _ Multifunction keys 1 and 2 l 1 line for displaying battery for entering figures and words condition and key functions and for menu navigation Function key for correcting data Keys 0 9 for entering input and selecting menu numbers and plain text j functions On Enter key to switch on the unit select functions and to set the lock to its starting position Battery condition full a Battery condition 2 3 full Key marked Function to hi Ji i Key marked Function for select the desired menu deleting the figure entered from the setting mode Battery condition 1 3 full Key marked Function to return to next higher menu A Sse Battery condition almost level empty Keys 1 and 2 to navigate through the menu page I Subject to modifications SELO B Standard Betriebsanleitung englisch p65 Date 03 05 B OPERATION Clearing the lock without opening delay factory setting 1 Press On Enter key When the lock is ready for operation the welcoming phrase on the display will soon be replaced by a message prompting the operator to enter a secret code The black rectangular cursor sits blinking at the first digit of the code entry field Key i
5. the opening delay the operator is prompted to enter a valid code Key in the valid code once more As a sign of its readiness for unblocking the lock will prompt the operator for five seconds to turn the round input unit and start unblocking the lock Unblocking the lock relocking and securing the lock 1 To unblock the lock during the five second readiness for opening turn the round input unit clockwise through a half turn from its end position Please note that the input unit can be turned a quarter turn at any time but that this distance is not enough to unblock the lock If the input unit is turned back to its starting position in anti clockwise direction after the five second ready for opening period the lock will return to the blocked position and can only be unblocked after renewed clearing and re entry of a valid code page 2 C CHANGING THE NUMERICAL CODE TEST TO BE PERFORMED WITHOUT FAIL For safety reasons only reprogram the lock with the safe door open and blocked in the open position Only after you are absolutely certain that the lock has been reprogrammed successfully and that the lock can be electrically cleared and mechanically unblocked using the new settings should the door be closed Enter the setting mode to change one of the codes ONLY CHANGE THE LOCK SETTINGS WITH THE SAFE DOOR OPEN AND BLOCKED DO NOT MAKE UP NUMBER CODE OF PERSONAL DATES i e no wedding anniversaries birthdays etc
6. he operation was not successful the message will read Wrong code You can leave the active menue field in the setting mode by pressing the Function key whenever you see the symbol lt above the key After leaving the setting mode the lock is again ready for clearing The operator is prompted to enter a valid secret code page 3 SELO B Standard Betriebsanleitung englisch p65 D CHANGING THE LANGUAGE Entering the setting mode to change the language setting 1 Press On Enter key When the lock is ready for operation the welcoming phrase on the display is followed after two seconds by a message prompting the operator to enter a valid code The black rectangular cursor sits blinking at the first digit of the code entry field and the capital letter M appears above the Function key By pressing the Function key the menue of the setting mode appears In this mode keys 1 and 2 serve as operating symbols for menue navigation up or down The first menue to appear is Code change Use the same keys T and 2 to address the other options on the menue Selecting a different language 1 Having entered the setting mode use keys 1 and 2 to go to the field Language Sprache in the menue factory setting when the lock is installed the first time is German deutsch Select by pressing the On Enter key 2 Use keys 1 and 2 to go to the language of your choice Select the new language by press
7. ing the On Enter key From now on all messages will appear in the language of your choice To leave the present menue field in the setting mode press the Function key whenever you see the symbol lt above the key After leaving the setting mode the lock is again ready for clearing The operator is prompted to enter a valid secret code in the language of their choice E REPLACING THE BATTERIES As soon as the symbol depicting the battery condi tion indicates almost empty the operator is also warned Please replace batteries each time the lock is operated We recommend you heed the advice and change the batteries The lock can only be unblocked a further approximately 50 times Please note that none of the number codes can be changed until a set of fresh batteries has been fitted To change the batteries lift off the cover of the battery compartment with the tip of a screwdriver Fit three leak proof type Mignon LR6 AA alka line batteries paying attention to the correct polar ity Dispose of the old batteries in accordance with anti pollution legislation F ADDITIONAL LOCK SETTINGS For detailed information about the additional lock functions please check the CD ROM supplied with the lock These functions cover Time functions Set time Set date Set access time frames Input range for timer A Input range for timer B Block for holiday periods Once only holiday periods Annually recurring holiday periods
8. lock confirms the successful change of the administrator code by means of the message Code change completed if the operation was not successful the message will read Wrong code You can leave the active menu field in the setting mode by pressing the Function key whenever you see the symbol lt above the key After leaving the setting mode the lock is again ready for clearing The operator is prompted to enter a valid secret code Changing an existing user code 1 2 As soon as you enter the setting mode the cursor will automatically go to Code change To select press the On Enter key Next the administrator and the various users are depicted on the display with the administrator in first place In the setting mode the symbols above keys 1 and 2 serve as operating symbols to navigate through the menue up or down Using keys 1 und 2 go to the user whose code is to be changed Select the desired user by pessing On Enter The lock now prompts the operator to key in the user s old code Enter old code and confirm by pressing On Enter Next the lock prompts the operator to key in the user s new code Enter new code and confirm by pressing On Enter As asafety measure the lock prompts the operator to enter the new code a second time Enter code and confirm once more by pressing the On Enter key The lock confirms the successful change of the user code by means of the message Code change completed if t
9. n the 7 or 8 digit number code factory setting administrator code 1 2 3 45 6 7 Following each successful entry a star appears in the space just completed and the blinking cursor shifts one place to the next figure to be entered After entering the last digit the code is validated by the lock Ifthe lock is able to match the entry with a previously programmed code it will prompt the operator for five seconds to turn the round input unit and to start unblocking the lock or Clearing the lock with a pre set opening delay between 1 and 99 minutes 1 Press On Enter key When the lock is ready for operation the welcoming phrase on the display will soon be replaced by a message prompting the operator to enter a secret code The black rectangular cursor sits blinking at the first digit of the code entry field Key in the 7 or 8 digit number code factory setting administrator code 1 2 3 4 5 6 7 Following each successful entry a star appears in the space just completed and the blinking cursor shifts one place to the next figure to be entered After entering the last digit the code is validated by the lock If the lock is able to match the entry with a previously programmed code it starts the preset opening delay and displays the remaining waiting time If the lock cannot match the entered code to a valid code it will send out a fault message Wait for the opening delay to come to an end Until it does the lock cannot be opened At the end of
Download Pdf Manuals
Related Search