Installation and operating instructions
Contents
1. me M LLER ELEKTRONIK Installation and operating Instructions Weather Station Version V2 20150416 MAL 3030247102 02 EN Read and follow these operating instructions Keep these operating Instructions in a safe place for later reference Company details Document Copyright O Installation and operating instructions Product Weather Station Document number 3030247102 02 EN As of software version 0 03 647 Original language German Muller Elektronik GmbH Co KG Franz Kleine Strabe 18 33154 Salzkotten Germany Phone 49 0 5258 9834 0 Fax 49 0 5258 9834 90 E mall info mueller elektronik de Homepage http www mueller elektronik de m Table of contents MULLER ELEKTRONIK Table of contents 1 For your safety 1 1 Basic safety instructions 1 2 Intended use 1 3 Layout and meaning of warnings 1 4 Disposal 2 Product description 3 Mounting and installation 3 1 Installing the Weather Station ol Installation with magnetic base 3 1 2 Installation with screws 3 2 Connecting the Weather Station to a terminal 4 Layout of work screen 5 Configuration 5 1 Calibrating the compass Dl Configuring the screen layout 5 3 Configuring alarms 5 4 Configuring the ISOBUS TC save interval 5 5 Configuring the filter 6 Technical specifications 6 1 Retrieve sensor information 6 2 Technical data for Weather Station with communication module 6 3 Connector pin assignment 6 3 1 92. permissible range Speed of true wind Air pressure with permissible range Direction of true wind Gust speed appears 10 minutes after switching on Air humidity with permissible range Se For a number of values you can see whether the weather data is within a permissible range You can see the permissible range from the colour of the bar graphs or of the borders of the wind display Green Value is within permissible range Red Value is not within permissible range Grey Value could not be found You can configure the permissible range gt 12 To display the slope of the vehicle and its current geographic position instead of weather data on the work screen press 10 3030247102 02 EN Configuration MULLER a ELEKTRONIK Calibrating the compass 5 Configuration 5 1 Calibrating the compass After installation on any new vehicle you must calibrate the Weather Station compass Procedure 1 On the work screen press EJ B3 EI 2 Select Yes 3 gt Start the compass calibration 4 Wait until the dot on the screen flashes yellow 5 Drive the vehicle in a circle as large as possible until the dot on the screen flashes green gt The compass calibration was successful 6 Repeat the process if the dot flashes red 5 2 Configuring the screen layout If you are using a Muller Elektronik terminal you can configure which weather data should be displayed in the header as well a
3. pin Sub D connector 6 3 2 8 pin M12 plug 7 Article overview V2 20150416 on A A A A A WO o u wa N O 10 11 11 11 12 12 12 13 13 13 14 14 14 15 For your safety Basic safety instructions 1 For your 1 1 A 1 2 1 3 safety Basic safety instructions Please read the following safety instructions carefully before using the product for the first time Before installation switch off the engine and the tractor s ignition Do not drop the components on the floor because they can be damaged The product does not include any user serviceable parts Do not open the casing Never clean the product with a high pressure cleaner as this will damage it Intended use The product is intended to accurately display weather data on an ISOBUS terminal The product is intended exclusively for use in agriculture The manufacturer shall not be held responsible for any other use of the system The manufacturer cannot be held liable for any personal injury or property damage resulting from such non compliance All risk arising from improper use lies with the user The operating instructions form part of the product The product may only be used in accordance with these operating instructions All applicable accident prevention regulations and all other generally recognized Safety industrial and medical standards as well as all road traffic laws must be observed Any unauthorized modifications made to
4. e or screw it to the roof of your vehicle 3 1 1 Installation with magnetic base Crushing hazard due to very powerful magnet The Weather Station has a very powerful magnetic base o Never place your fingers between the Weather Station s magnetic base and a metal surface o Hold the Weather Station in your hands firmly but do not place your fingers beneath the magnetic base Procedure V2 20150416 Mounting and installation MULLER ELEKTRONIK Installing the Weather Station 5 Identify an appropriate position on the roof of the vehicle This position must not be in the slipstream 6 Use alcohol to clean the position on which will you want to mount the Weather Station 7 Stick the provided 3M double sided adhesive tape onto the clean surface 8 Clean the provided metal plate 9 Remove the protective paper from the 3M adhesive plate and bond the metal plate onto this Place the magnetic base and Weather Station onto the metal plate Ensure that the Weather Station is firmly secured The recess must face the direction of travel gt You can now connect the Weather Station to a terminal 3 1 2 Installation with screws Procedure gt 1y di d M 2 4 Identify an appropriate position on the roof of the vehicle This position must not be in the slipstream 8 3030247102 02 EN Mounting and installation Connecting the Weather Station to a terminal 5 Use alcohol to clea
5. n the position on which will you want to mount the Weather Station Screw the Weather Station firmly onto the roof of the vehicle Ensure that the Weather Station is firmly secured The recess must face the direction of travel gt You can now connect the Weather Station to a terminal 3 2 Connecting the Weather Station to a terminal Terminal connector supplying power Potential damage to the terminal from a short circuit o Switch the terminal off before plugging in or removing the connector Procedure M You have now installed the Weather Station EP Switch off the terminal 2 Route the cable of the Weather Station into the vehicle cab 3 Connect to be cable from the Weather Station so the cable of the communication module 4 Connect connector A of the communication module to the CAN bus socket of the terminal For the majority of terminals from Muller E lektronik this is going to be the A socket gt The Weather Station is now connected between the basic vehicle harness and the terminal You can now launch of the Weather Station application V2 20150416 9 Layout of work screen MULLER ELEKTRONIK 4 Layout of work screen You can view directly all of the data determined by the Weather Station on the work screen ather Station a a 1014 hPa 968 1040 1 Driving speed 7 Direction of apparent wind 2 GPS status Speed of apparent wind ISOBUS TC status 9 Temperature with
6. ork screen press 509 QZ gt As 2 Configure the parameters 3030247102 02 EN Technical specifications MULLER insta ELEKTRONIK Retrieve sensor information 6 Technical specifications 6 1 Retrieve sensor information On the Information screen you can retrieve various information on the Weather Station The following information is displayed S oftware version of the communication module Sensor nfomaton Model ID Model identification number for the Weather Station Procedure 1 On the work screen press 6 2 Technical data for Weather Station with communication module Operating voltage 9 16 V Temperature range 20 C to 55 C Deia Protection class IP X6 V2 20150416 13 Technical specifications Connector pin assignment 6 3 Connector pin assignment 6 3 1 9 pin Sub D connector Signal Pinos signal cut e CS ewan fom canon e ETS coe eve cen 6 3 2 8 pin M12 plug 14 3030247102 02 EN an Article overview MULLER ELEKTRONIK 7 Article overview 3030247102 Weather Station without communication module with base harness and connector cable 3030247105 Weather Station with communication module with base harness and connector cable 3030247101 Communication module V2 20150416 15
7. s in the additional window on the display screen Procedure 1 On the work screen press EI 2 Configure the screen layout You can see which display corresponds to the different parts of the screen from the following illustrations ay Lag 1009 nN 391 hPa 3650 1645 6 106 N 22 to 10 L of ch SS Layouts in the additional window a ON 39 l ioe 6 45 6 166 368 1646 Layouts in the header V2 20150416 11 Configuration Configuring alarms 5 3 Procedure 3 4 Procedure 9 9 Procedure 12 Configuring alarms You can set measurement values for different weather data for which an alarm is triggered See the screen to see which alarms you can set You can also seta permissible range You can see the permissible range in the green area on the bar graphs on the work screen gt 10 1 On the work screen press AR 2 Configure the alarms Configuring the ISOBUS TC save interval The time set indicates the number of seconds after which the ISOBUS TC application should record the determined weather data 1 On the work screen press 2 Configure the parameter Configuring the filter You can configure a filter for true and apparent wind The average wind speed within the time set is always displayed on the work screen The shorter the time the more accurate the values Shorter times also mean that values will often fluctuate 1 On the w
8. the equipment will void the manufacturer s warranty Layout and meaning of warnings All safety instructions found in these Operating Instructions are composed in accordance with the following pattern This signal word identifies medium risk hazards which could potentially cause death or serious physical injury if not avoided 3030247102 02 EN ss For your safety MULLER ELEKTRONIK Disposal This signal word identifies low risk hazards which could potentially cause minor or moderate physical injury or damage to property if not avoided This signal word identifies actions which could lead to operational malfunctions if performed incorrectly These actions require that you operate in a precise and cautious manner in order to produce optimum work results There are some actions that need to be performed in several steps If there is a risk involved in carrying out any of these steps a safety warning will appear in the instructions themselves Safety instructions always directly precede the step involving risk and can be identified by their bold font type and a signal word Example 1 NOTICE This is a notice It warns that there is a risk involved in the next Step 2 Step involving risk 1 4 Disposal When it has reached the end of its service life please dispose of this product as electronic scrap in accordance with all applicable waste mm management laws V2 20150416 2 Product description Prod
9. uct description The Weather Station Is a sensor which can determine different weather data and display iton an ISOBUS terminal Ifa Weather Station is connected to a terminal the ISOBUS TC application will save the determined weather data The Weather Station can determine the following values All values can be displayed using the metric or imperial systems Speed and direction of true wind Actual wind speed and direction relative to North Speed and direction of apparent wind True wind together with slipstream The latter is the wind felt by the machine user Example When driving at speed of 20 km h in an eastward direction with a wind of 10 km h from the west apparent wind is 10 km h from the East Gust speed A gust speed will be displayed if there is a brief increase in wind speed of more than 5 km h above the average wind speed for the last 10 minutes Temperature Relative air humidity Air pressure With GPS reception Air pressure is set to sea level Without GPS reception Air pressure is set to the current position of the vehicle i e the height of the terrain Roll Slope the vehicle along its longitudinal axis Pitch Slope of the vehicle along its transverse axis Driving speed 3030247102 02 EN Mounting and installation Installing the Weather Station 3 Mounting and installation 3 1 Installing the Weather Station You can either install the Weather Station using its magnetic bas
Download Pdf Manuals
Related Search