Digital Gear Display Operating Instructions
Contents
1. 2 1 1 2 3 1 The vehicle should be placed on a surface that Fastening the reference box is as level as possible before programming The box should be placed as horizontally as pos Since the vehicle has to start in first gear after sible in the area of the switching lever Labelling programming light acceleration please ensure points up Fig 4 now that there are no obstacles 20 metres straight on are sufficient and that traffic is not 2 3 2 impaired Remove protective foil from the adhesive strips position reference box and press on firmly 2 1 2 Verify that the gear lever is still set to idle Now Start the engine gear lever set to idle acknowledge the box position by briefly pressing the push button 2 2 1 LCD Colour selection Colour change by position change of the refe rence box Keep the reference box button 3 pressed for approx 5 s until C is displayed then let go of the button Tilt the reference box forwards and backwards in your hand to start colour selection The colour changes in small nuances when the reference box position is adjusted slightly Briefly confirm desired colour by pressing the push button on Figure 4 2 3 3 Gear programming now starts Starting in first gear the display now shows all gears in sequen ce as flashing figures 2 3 4 Display 1 please switch to first gear 2 e please switch to second gear 3 please switch to third gear 4 please switch to fo2. connected to one reference box Vehicle battery voltage too low
3. Cable ties 1x Gear lever knob installation 1 1 1 Disassembly of the original gear lever knob and gear boot Install LCD gear lever knob and gear boot the data cable at the gear lever knob must not be damaged The gear boot can be placed between the gear lever knob and the retention ring to cover it or below the retention ring For this the retention ring can be pushed on in two different directions fig 2 and 3 with radius up or radius down 1 2 1 Connection reference box 3 The reference box should not be glued on before programming of the colour Figure 2 Figure 3 Connect the plus line from the ignition and ground line to the power supply lines of the reference box red to 12 Volt from the ignition black to ground The included cable clamps can be used here Finding possible reference box position De grease this surface for gluing on the reference box 3 and clean it Data cable connection between the LCD gear lever knob and reference box 3 it is unimportant which one of the two sockets is used Fasten data cable to the gear lever with cable tie as strain relief 1 2 2 Switch on ignition briefly to check display or connections Reprogrammed display shows a rotating or running bar A q TEES Programming Programmes individual gear lever positions of the reference box once Display now indicates a trans your car for gear recognition and display verse bar Gas gt
4. INDY CATOR Digital Gear Display Operating Instructions GASLOCK Table of Contents About INDY CATOR Package content Gear lever knob installation Programming Troubleshooting About INDY CATOR First we would like to explain to vou the function of the digital gear display It works according to the principle of forming the difference between two position sensors As a result the selected transmission is displayed for you The electronic system recognises even the smallest changes of positions of the gear lever knob It works completely independently of the vehicle transmission Only if a position change is safely recognised as a transmission change will the display change This may take 1 1 5 s This transmission display is to serve as an aid We assume no warranty for correctness of the display If the transmissions are not displayed correctly for some reason please repeat programming with the motor gear at operational temperature Depending on vehicle type and gear position extreme vehicle acceleration may lead to short term reading changes on the display This is based on the physical characteri stics of the sensors and does not constitute any malfunction Package content 1 2 3 4 5 6 7 Gear lever knob with retention ring 1x Data cable 1x Reference box with power supply lines 1x Hexagon socket wrench 1x Grub screws long and short 2x one each Cable terminal clamps 2x
5. urth gear D e please switch to fifth gear if the vehicle only has 4 gears ignore display and leave it in 4th gear 6 please switch to sixth gear if the vehicle does not have any 6th gear ignore display and leave it in 5th or 4th gear foo please switch to reverse gear if there is no gear change the display change may take approx 30 S 1 please switch back to first gear Ao Now accelerate the vehicle in first gear start driving as normal Once the display recognises acceleration a running bar is displayed TR J VE After a few seconds the number of the active gear is displayed here it is the number 1 Your Indy Cator gear display is now programmed and ready for operation Please switch off the motor Programming remains saved with the display ignition switched off The gear boot and any applicable covers in the car can now be re assembled Troubleshooting If re programming is required press the button of the reference box until C is displayed and start again as described on page 6 If the previously selected colour is to be retained please confirm it with the button without moving the reference box again Display only shows running ring ER E TEE Gears not programmed Programme gears Gears are not recognised displayed incorrectly Gear lever loose Reference casing loose Re programme gears Changing LCD display brightness Too many display instruments
Download Pdf Manuals
Related Search