Installation and Operating Instructions
Contents
1. he relevant stainless steel fastening unit e Installation position The light guide housing must be installed horizontally or with the light guide at the top e Replacement parts and accessories Please use only original spare parts Have the luminaire serviced by the manufacturer whenever necessary e Maintenance Keep the luminaire clean Once the luminaire has been opened the thread of the screwed glass lens 1 4 should be greased again e g with AEMA SOL 6 B made by A E Matthes The average service life of the bulb should be observed All dimensions in mm unless stated otherwise Subject to change without prior notice ric 01 13 P APENMEIER Claw spanner for screwed glass lens 6805 002 00 Mounting brackets for light 0354 005 00 generator straight Fastener for light guide head 1947 005 00 Screwed glass lens light outlet 1774 089 00 0862 020 00 F H Papenmeier GmbH amp Co KG division Lumiglas Talweg 2 58239 Schwerte GERMANY phone 49 2304 205 0 fax 49 2304 205 206 info lumi papenmeier de www lumiglas de2. lumiglas Installation and Operating Instructions C oss 0093 102 00 b Lumiglas luminaire Lumiflex USL 07 ALF Ex Il 2G Ex de IIC T6 T4 Gb Il 2D Ex tb IIIC T80 C T130 C Db e Important please note This Lumiglas Ex light guide luminaire can be used as a sight glass luminaire or for illuminating individual objects e g on machine tools Ex classified luminaires with light guide are also intended for observing processes in reactors plants vessels etc wherever the use of standard Ex luminaires is not possible due to space restrictions Under no circum stances should a sight glass luminaire be utilised to replace the cover flange or the complete sight glass flange fitting or used on its own to cover a container port Luminaires for potentially explosive areas must always be installed connected and serviced by persons who have been specially trained and authorised to do this work ty 4 singe A A ST AA e sa tat e General operating conditions Independent of internal pressure vacuum in the vessel when used as a sight glass luminaire Approved for use in Ex hazardous environments Gas Zones 1 and 2 Dust Zones 21 and 22 Also suitable for illumination purposes in Zone 0 and Zone 20 together with a sight glass The specified temperatures and installation position must be observed to ensure faultless operation Approved for applications at ambient temperatures of between 20 C and 40 C or up to 60 C Temperat
3. rds undo the nation certificate wires to the lamp at the terminal f Voltage type Alternating voltage AC The luminaire is Pull the bulb e past the retaining screw and remove it fitted with an integrated transformer Overvoltage will Carefully insert the new bulb following the instructions on cause premature lamp failure the enclosed leaflet Re attach the wires to the terminal e Electrical connection Swivel the bulb holder with bulb back into place and The connecting cable used must be capable of withstanding secure with the retaining screw an operating temperature of between 20 C and at least Screw the glass lens back onto the housing until it is tight 95 C such as Sinotherm 110 HOSGG F 3G 1 5 mm again pressure against O ring Open the cover of the terminal box on the light gene The locking plate must engage in one of the notches to rator 1 ensure the screwed sight glass is locked Loosen the cable relief screws with anti rotation tabs of Tighten the locking screw again Carefully position the the cable entry gland 1 7 light guide in the slot again and screw it against the O ring Insert the cable with the connecting cords through the until it is tight Ex e cable gland M20 x 1 5 1 7 into the terminal compart Once the luminaire has been properly mounted it is ready ment Then tighten the screws again for operation Connect to Ex terminal 1 6 Connect the protective ground wire
4. to the internal protec tive ground terminal 1 5 Connect the external protective conductor terminal 1 1 to a separate operational earth Place the cover seal in position Close the cover and screw it tight The connecting cable should be tied at a max distance of 1 m from the light generator and fixed in place F H Papenmeier GmbH amp Co KG division Lumiglas Talweg 2 58239 Schwerte GERMANY phone 49 2304 205 0 fax 49 2304 205 206 info lumi papenmeier de www lumiglas de PAPENMEIER lumiglas e Electrical data Light generator luminaire enclosure Protective conductor terminal external Locking screw Locking plate Screw type sight glass Protective conductor terminal internal Ex terminal Cable entry gland M20 x 1 5 Ex e Cable bushing M20 x 1 5 Ex d ee ee TL Light guide 7 Stainless steel aa Attachment piece on light generator Stainless steel Protective hose Stainless steel Light guide head Stainless steel e Mechanical assembly Caution Avoid looking into the light source risk of damage to the eyes The light generator 1 is mounted at a suitable place on the reactor apparatus etc using the fastening element provided The light guide must be mounted free of tension or twisting with a bending radius of at least 170 mm and installed with the light guide head holder The light guide head 2 3 is screwed to the place to be illuminated using t
5. ure resistance of light guide 20 C to 150 C ae Lumiglas Ex luminaire with light guide Lumiflex USL 07 ALF Ex e Electrical data general e Changing the lamp The voltage output temperature class and type of Disconnect the luminaire from the mains supply and ob protection are specified on the type plate serve the waiting time specified on the type plate Lamp wattage 20 W 39 W To change the lamp loosen the light guide 2 from its IP65 and IP67 acc to EN 60529 DIN VDE 0470 Part 1 holder on the screwed sight glass 1 4 and pull it out Ex approval acc to EC type examination certificate The light guide and the receptacle hole must be treated BVS 10 ATEX E 100 X with care and protected against damage important to the Il 2G Ex de IIC T6 T4 Gb Ex protection function Keep the screws in a safe place Il 2D Ex tb IIIC T80 C T130 C Db Loosen the locking screw 1 2 for the screwed sight glass The 20 W transformer variant is PTC protected The 39 W 1 4 this will release the locking plate 1 3 version is fused using a 315 mA fusible cut out acc to The screwed glass lens should only be loosened and IEC 60127 2 3 Do not change the fuse until the appliance dismantled using the special claw spanner 6805 002 00 has been disconnected from the mains In the open bulb compartment loosen the retaining screw It is essential to comply with the data in the EC type exami c of the bulb holder and swivel it upwa
Download Pdf Manuals
Related Search