Home

BM Programming Module Operating instructions

1. The BM programming module also offers the following special functions Heating Heating over a period of up to 30 days Reduce Reduce mode over a period of up to 30 days 1xDHW One off cylinder charging for one hour Keylock Prevents inadvertent alteration of the settings Switch times Times for the automatic timer mode Room influence programming module as remote control Correction function to compensate for temperature influences Winter summer changeover Optimisation of the heating times ECO RED ECO reduction Optimisation of heating times in the setback mode Operating Instructions BM Programming Module 3062600 201208 Operation 4 Operation 4 1 Overview of the BM programming module ced X 1234567 gt D i45 memkYiK Mz E x Fig 4 1 BM programming module 1 Temperature correction 2 Right hand dial 3 Heating button 4 Reduce button 5 Function displays 6 1x DHW button 7 Info button 8 Left hand dial 9 Operating mode 10 Status display 10 Operating Instructions BM Programming Module 3062600_201208 Operation 4 2 Display overview Room temperature boiler temperature mixer circuit temperature or solar system hot water temperature The display of the BM programming module shows the following temperatures depending on the installation location Room temperature remote control Boiler temperature boiler Mix
2. Only active with BM in wall plinth Subject to the configuration of the system Time programme for mixer adjustable if mixer module connected Fig 5 1 Menu structure of the BM programming module 22 Operating Instructions BM Programming Module 3062600 201208 Basic settings DISPLAY RETURN TEMP DAY PEt tri ti bait iit pais 7 a ZEATEEEEELELEEELEIAS uiu HES LOCK M mimis 0145 mA I gt If this arrow Y appears in the display then there is a sub menu If you press the right hand dial when at the RETURN menu point you will return to the calling menu If a value can be set then the adjustable value flashes in the display If the display shows KEY LOCK then the key lock is activated gt You can temporarily deactivate the key lock by pressing the right hand dial for about 2 seconds Operating Instructions BM Programming Module 3062600_201208 23 Basic settings 1234567 D i45 Setting range 0 00 23 59 5 1 Setting the time winter summer time The BM programming module only automatically sets the time and day if a radio controlled clock module is connected gt Ask your heating engineer whether he has fitted a radio controlled clock module with outside sensor Winter summertime changeover The time is automatically changed over to summer or wintertime see also system parameter A20 g
3. C FLOW RATE Solar circuit flow rate I min SOLAR DHW 2 Hot water ACTUAL temperature solar cylinder 2 C Maximum temperature solar cylinder sensor 2 C DHW SOL 24H Minimum temperature solar cylinder sensor 2 C COLLECTOR 2 Collector temperature solar system collector array 2 C Maximum temperature solar system collector array 2 C COLLECT 24H Minimum temperature solar system collector ray 2 C SOLAR DHW 3 Hot water ACTUAL temperature solar cylinder 3 in C DHW SOL 24 H Maximum temperature solar cylinder sensor 3 C Minimum temperature solar cylinder sensor 3 C Table A 1 Display continued on next page 48 Operating Instructions BM Programming Module 3062600 201208 Appendix Display Name OPERATION H 1 Operating hours solar circuit pump 1 h OPERATION H 2 Operating hours solar circuit pump 2 h OPERATION H 3 Operating hours solar circuit pump 3 h SOL OUTPUT Current output solar system kW OUTPUT 24H Current output 24 h solar system kW ZOUTPUT KWH Total output solar system kWh ZOUTPUT MWH Total output solar system MWh SOL STATUS 1 Hot water charging solar cylinder 1 Anti legionella function solar cylinder 1 0 not successful 1 successful Hot water charging solar cylinder 2 SOL STATUS 2 Anti legionella function solar cylinder 2 0 not successful 1 successful Ho
4. Danger of scalding by hot water with solar hot water generation With solar hot water generation the hot water temperature can be hotter than 90 C and can cause scalding gt Ask your heating engineer for a suitable temperature limiter Danger Danger of scalding by hot water Water temperatures in excess of 65 C can cause scalding gt Do not set the hot water temperature above 60 C Factory setting 50 C Setting range 15 65 C gt Press the right hand dial gt Turn the right hand dial to the BAS C SET menu gt Press the right hand dial gt Turn the right hand dial to the DHW TEMP sub menu gt Press the right hand dial to change the temperature gt Select the hot water temperature by turning the right hand dial gt Confirm the hot water temperature by pressing the right hand dial You go back to the basic display by pressing the Info button Operating Instructions BM Programming Module 3062600 201208 27 Basic settings RED TEMP 16 0 Factory setting 16 C Setting range 5 30 C 5 5 Setting the reduced temperature reduction The reduced temperature is the temperature to which the heating circuit room temperature is heated to outside the switching times Programme the switching times heating times e g at night or when you are away or in setback mode If the room influence function is not set BM programming module i
5. cylinder charging pump transports the boiler water and thus the heating heat to the heat exchanger of the DHW cylinder Operating Instructions BM Programming Module 3062600_201208 53 Glossary eBUS eBUS is a protocol for networking of components of a heating system with the aim of facilitating central control of the entire heating system ECO RED The ECO REDUCTION function effects automatic switching on or off of the heating during setback operation if the average outside temperature exceeds or falls below a specified value for example if there are high outside temperatures during the night Expert level The setting facilities in the expert level are reserved for the heating engineer This facility serves to ensure your safety since incorrect entries can cause injury or damage to the heating system Flow temperature The flow temperature designates the temperature of the heating water flowing to the radiator It lies between 35 C and 70 C depending on the outside temperature in outside temperature controlled heating control systems In heating systems with simple surface heating 25 C to 40 C is adequate In heating systems without a mixer circuit the flow temperature is the same as the temperature of the boiler water 54 Operating Instructions BM Programming Module 3062600_ 201208 Glossary Frost protection The heating engineer sets a temperature value on the BM programming module belo
6. timer programme Using the timer programme you specify whether the switch times are to be programmed for the day blocks Mo Fr and Sa Su or for each day individually gt Press the right hand dial gt Turn the right hand dial to the BASIC SET menu gt Press the right hand dial If a heating circuit and one or more mixer circuits are connected e g radiator and underfloor heating then first select the relevant heating or mixer circuit gt Turn the dial to the HC or MK1 MK7 sub menu gt Press the right hand dial gt Turn the right hand dial to the TIME PROG entry gt Press the right hand dial to change the timer programme gt Select the timer programme by turning the right hand dial 1 Mo Fr and Sa Su 2 Mo Fr and Sa Su 3 Mon Tue Wed Thu Fri Sat Sun gt Confirm the timer programme by pressing the right hand dial You go back to the basic display by pressing the Info button Operating Instructions BM Programming Module 3062600 201208 31 Basic settings WITCH TIE U6 00 1234567 2 00 Setting range 00 00 00 00 in 15 min steps 5 6 3 Programming heating times The heating times are used to specify when the heating is switched on and off in the Automatic timer mode Press the right hand dial Turn the right hand dial to the TIME PROG menu Press the right hand dial Turn the right hand dial to the HEATING menu vvv yv If a heating ci
7. 9 30 31 32 34 Operating Instructions BM Programming Module 3062600_ 201208 Contents 5 6 5 Programming the circulation pump times 35 5 7 Setting the key lock 36 5 8 Setting the room influence 37 5 9 Setting the winter summer changeover 38 5 10 Setting ECO RED 39 5 11 Setting the heating curve 40 5 12 Setting the language 41 5 13 Selecting the cooling function with heat pump 42 5 14 Setting the cooling temperature 43 6 Energy saving tips 44 7 Messages and faults 46 7 1 Service 46 7 2 Fault 46 7 2 1 Message on the boiler 46 8 Technical data 47 Appendix 48 Table of Info button displays 48 Boiler HG status table 51 Parameter overview basic settings 52 Glossary 53 Alphabetical index 57 Operating Instructions BM Programming Module 3062600 201208 3 Notes concerning the documentation 1 Notes concerning the documentation 1 1 Other applicable documents Operating instructions for the boiler For the heating engineer Installation instructions for BM programming module Installation instructions for the boiler The instructions for all accessory modules and other accessories may also be applicable 1 2 Safe keeping of the documents The operator or the user of the system is responsible for the safe keeping of all manuals and instructions gt This operating manual and all other applicable documents must be handed on to subsequent owners 1 3 Symbols and warning notices used Symbol for additional inf
8. D ln Setting range 00 00 00 00 in 15 min steps 5 6 4 Programming hot water times Using the hot water times you can specify at which times the hot water is available at the set hot water temperature The DHW cylinder is not heated up by the boiler outside the switch times If you have a heating system with solar assistance then the DHW cylinder is also heated up outside the switch times provided that solar energy is available gt Press the right hand dial gt Turn the right hand dial to the TIME PROG menu gt Press the right hand dial gt Turn the right hand dial to the HOT WATER DHW menu v Select the day day block by turning the right hand dial Press the right hand dial Select the switch time by turning the right hand dial Confirm the selection by pressing the right hand dial Set the start time 2X by turning the right hand dial Confirm the start time by pressing the right hand dial Set the end time by turning the right hand dial Confirm the end time by pressing the right hand dial vvvvvvyv You go back to the basic display by pressing the Info button 34 Operating Instructions BM Programming Module 3062600_ 201208 Basic settings SWITCH TINE 05 00 1234567 22 00 Setting range 00 00 00 00 in 15 min steps 5 6 5 Programming the circulation pump times Using the circulation pump times you can stipulate at which times the circulation
9. Programming Module 3062600 201208 39 Basic settings 5 11 Setting the heating curve The GRADIENT sub menu is only displayed in systems with an outside sensor connected The day temperature is controlled indirectly via a heating curve The heating curve represents the relationship between the outside temperature and the flow temperature The flow temperature is the temperature of the heating water as it leaves the boiler The heating curve can be set individually for the heating circuit and one or more mixer circuits The required basic setting to the heating curve has been carried out by your heating engineer when installing the heating system gt b Caution Danger of damage caused by high flow temperatures Flow temperatures in excess of 40 C with underfloor heating can cause damage to the floor covering With underfloor heating the heating curve should be set to a maximum of 0 8 gt Setthe heating curve so that the flow temperature does not rise above 40 C gt The heating curve should only be changed in consultation with your heating engineer You go back to the basic display by pressing the Info button 40 Operating Instructions BM Programming Module 3062600_201208 Basic settings ENGLISH Factory setting English 5 12 Setting the language You can change the language setting of the BM programming module Press the right hand dial Turn the r
10. WOJIF For the user Operating instructions BM Programming Module WOLF GmbH Postfach 1380 84048 Mainburg Tel 08751 74 0 www wolf heiztechnik de G B Document no 3062600_201208 Subject to modifications Contents Contents 1 Notes concerning the documentation 1 1 Other applicable documents 1 2 Safe keeping of the documents 1 3 Symbols and warning notices used 1 3 1 Structure of warning instructions 2 Safety and regulations 2 1 Intended use 2 2 General safety instructions 3 Equipment description 4 Operation 4 1 Overview of the BM programming module 4 2 Display overview 4 3 Operating modes 4 4 Setting automatic timer operation 4 4 1 Setting summer mode 4 4 2 Setting continuous operation mode 4 4 3 Setting the setback mode 4 4 4 Setting stand by mode 4 4 5 Setting the maximum output mode 4 4 6 Temporary room temperature adaptation 4 5 Starting the heating 4 6 Starting reduction 4 7 Starting the 1x DHW function 4 8 Displaying information 5 Basic settings 5 1 Setting the time winter summer time 5 2 Setting the date 5 3 Setting the day temperature heating 5 4 Setting the hot water temperature 5 5 Setting the reduced temperature reduction 5 6 Switch times 5 6 1 Pre programmed switch times 5 6 2 Selecting the timer programme 5 6 3 Programming heating times 5 6 4 Programming hot water times 8 10 10 11 13 13 14 14 15 15 16 17 18 19 20 21 22 24 25 26 27 28 2
11. and switches the boiler on The heating mode can be set for a period of one hour to 30 days The heating heats up to the set room temperature day temperature After the selected time period has elapsed the boiler switches back to the previously set operating mode Within the switch times the DHW cylinder is heated up to the set hot water temperature gt Press the Heating button gt Select the period in which the heating should heat to the day temperature by turning the right hand dial Setting range 0 23 hours or 1 30 days gt Confirm the time for the heating mode by pressing the right hand dial After a few seconds the display switches back to the basic display In the status display the Heating mode symbol 3X flashes gt To terminate the Heating special function prematurely press the Reduce button 18 Operating Instructions BM Programming Module 3062600_ 201208 Operation REDUCE 03 00 SIL Factory setting 3 hours Setting range 0 23 hours or 1 30 days 4 6 Starting reduction Use the Reduce special function in order not to have to change the programmed switch times for heating and hot water generation if you are away for extended periods or on holiday The Reduce special function bypasses all set time programmes or operating modes and switches the boiler to setback operation The setback mode can be set for a period of one hour to 30 days After the selected ti
12. er circuit temperature mixer module Solar system hot water temperature solar module Time and outside temperature The display on the BM programming module shows the time and the outside temperature alternately if an outside sensor is connected Day The display on the BM programming module shows the currently set day 1 Monday 1234567 2 Tuesday E M 4 Left hand arrow operating mode set gt Right hand arrow room temperature correction set Operating Instructions BM Programming Module 3062600_201208 11 Operation Status display The display on the BM programming module shows the current operating mode of the heating system 3s Automatic timer mode or continuous mode Hot water generation enabled mi b Stand by mode amp Setback mode Flue gas test maximum output mode is active lt Heating button has been pressed BO 1x DHW button has been pressed J Reduce button has been pressed Function displays The display on the BM programming module shows the current function of the heating system Boiler in heating mode Boiler in hot water mode Pump on the boiler ON Burner ON Mixer circulation pump for Mixer 1 ON Mixer circulation pump for Mixer 2 ON Programmable output ON II 12345 A1 maask Yx A So Th YY R ao OF Solar circuit pump 1 active Solar circuit pump 2 active eBUS connection active Burner stage 1 active multi stage bu
13. fluence on OFF room influence off gt Confirm the setting by pressing the right hand dial You go back to the basic display by pressing the Info button Operating Instructions BM Programming Module 3062600 201208 37 Basic settings U S SWITCH cu Factory setting 20 C Setting range 0 40 C 5 9 Setting the winter summer changeover The winter summer changeover function is only active if an outside sensor is connected The winter summer changeover should only be changed in consultation with your heating engineer The winter summer changeover function optimises the times at which the heating heats to the day temperature If the average outside temperature is in excess of the set winter summer temperature then the heating switches to the Stand by mode If the average outside temperature is below the set winter summer temperature then the heating switches to the Automatic timer mode The period for calculation of the average outside temperature is set by your heating engineer gt Press the right hand dial gt Turn the right hand dial to the BAS C SET menu gt Press the right hand dial If a heating circuit and one or more mixer circuits are connected e g radiator and underfloor heating then first select the relevant heating or mixer circuit gt Turn the dial to the HC or MK1 MK7 sub menu gt Press the right hand dial gt Turn the right hand dial to the W S SWITCH sub men
14. g Module 3062600 201208 43 Energy saving tips 6 Energy saving tips Room temperature day temperature Set the room temperature to a level that you feel as being just comfortable One degree increase in the room temperature means an increase in energy consumption of about 6 Do not heat rarely used rooms or bedrooms continuously as you do with rooms that are in use Efficient heating All rooms in the house or apartment should be heated An individually heated room also heats the adjoining rooms Heat the rooms according to their use Maintain a minimum temperature in all the rooms In unheated rooms humidity can condense on the walls and consequently damage the structure of the building Thermostatic valves Thermostatic valves maintain the set temperature They automatically open if the room temperature is low and close at a higher temperature All the thermostatic valves in the room where the BM programming module is installed should be fully open since otherwise the thermostatic valves and the programming module will influence each other Heating system service Deposits of rust in the burner chamber of a boiler or a badly adjusted burner can easily reduce the efficiency of a heating system by 5 or more Regular service of the system by a specialist heating company will soon pay for itself Freely accessible radiators The air must be capable of circulating well in the vicinity of the radiator otherwise the eff
15. grammed for the day blocks Mo Fr and Sa Su or for each day individually You can then programme the switch times to meet your wishes Three switch times are available for each day block or day You can programme individual switch times for the heating circuit each additional mixer circuit the hot water generation and the circulation pump Three switch time programmes are pre programmed in i the factory Operating Instructions BM Programming Module 3062600 201208 29 5 6 1 Pre programmed switch times Time pico Switch HC Mix valve yong Circulation prog time ON OFF ON OFF ON OFF ON OFF Time Mo Fr 1 6 00 6 30 prog 1 2 17 00 18 30 3 Sa Su 1 6 30 7 00 2 11 00 12 00 3 17 00 18 30 Time Mo Fr 1 6 00 6 15 prog 2 2 3 Sa Su 1 6 30 6 45 2 16 30 17 00 3 Time Mon 1 6 00 6 30 prog 3 2 17 00 17 30 3 Tue 1 6 00 6 30 2 17 00 17 30 3 Wed 1 6 00 6 30 2 17 00 17 30 3 Thu 1 6 00 6 30 2 17 00 17 30 3 Fri 1 6 00 6 30 2 17 00 17 30 3 Sat 1 6 00 6 30 2 17 00 17 30 3 Sun 1 5 30 21 00 4 30 20 00 5 00 7 00 6 00 6 30 2 15 00 21 00 17 00 17 30 3 Table A 2 Pre programmed switch times 30 Operating Instructions BM Programming Module 3062600 201208 Basic settings TINE PROG Factory setting 1 Setting range 1 2 3 5 6 2 Selecting the
16. hing time must be enabled for heating gt Press the right hand dial gt Turn the right hand dial until you reach the menu BASIC SET gt Press the right hand dial gt Turn the right hand dial until you reach submenu COOLING FCN gt To change the cooling function press the right hand dial gt Select the cooling function by turning the right hand dial Available options are ON cooling functions switched on OFF cooling functions switched off gt Confirm the selection by pressing the right hand dial Return to the basic display by pressing the Info button 42 Operating Instructions BM Programming Module 3062600_ 201208 Basic settings 5 14 Setting the cooling temperature If linked to a Wolf heat pump and BKM cooling module the BM can be used to enable a cooling function for a heating circuit and to set the cooling temperature COGLING T 2c nor 25 0 70 d Factory setting 25 C Setting range 5 to 35 C Press the right hand dial Turn the right hand dial until you reach the menu BASIC SET Press the right hand dial Turn the right hand dial until you reach submenu COOLING T To change the cooling temperature press the right hand dial Select the cooling temperature by turning the right hand dial Confirm the selection by pressing the right hand dial Return to the basic display by pressing the Info button Operating Instructions BM Programmin
17. iciency of the heating will be reduced Modern radiators emit part of the heat as radiated heat Long curtains or incorrectly placed furniture can absorb up to 20 of the heat 44 Operating Instructions BM Programming Module 3062600_ 201208 Energy saving tips Leave the heat in the room even at night Closing roller shutters and drawing curtains noticeably reduces the loss of heat at night from the room via the window areas Insulating the radiator recesses and painting the wall a light colour will save up to 4 of the heating costs Even tight seals on windows and doors retain the energy in the room Ventilation Ventilate the rooms by turning the thermostatic valves down and open the windows in the room or better still in the whole apartment to produce a so called through draught ventilation The short and effective ventilation process just changes the air in the room and the furniture and walls soon return their stored heat to the cool air again Bleeding the radiators Regular bleeding of the radiators in all the rooms particularly in the upper apartments in houses with multiple occupancy ensures perfect functioning of the radiators and thermostatic valves The radiator reacts quickly to changes in heat demand Setback operating mode reduced temperature Set the reduced temperature just 5 C lower than the room temperature day temperature If you set the setback temperature lower then you will lose the
18. ight Red flashing Fault Burner on flame on Tab 7 1 Meaning of illuminated ring on boiler 46 Operating Instructions BM Programming Module 3062600 201208 Technical data 8 Technical data Designation eBUS supply voltage 15 24 V Power consumption max 0 5 W Wall plinth protection IP 30 rating Boiler protection rating as per control system protection rating Running reserve gt 48 hours Ambient temperature 0 50 C Data retention EEPROM permanent Electromagnetic Compatibility Directive CE marking Directive 2004 108 EU Low Voltage Directive Directive 2006 95 EU Tab 8 1 Technical data Operating Instructions BM Programming Module 3062600_ 201208 47 Appendix Appendix Table of Info button displays Displays for the Info button or the DISPLAY menu Display Name Hot water ACTUAL temperature heating C DAW TEMP Hot water SET temperature heating C SOLAR DHW 1 Hot water ACTUAL temperature solar cylinder 1 in C DHW SOL 24 H Maximum temperature solar cylinder sensor 1 C Minimum temperature solar cylinder sensor 1 C COLLECTOR 1 Collector temperature solar system collector array 1 C Maximum temperature solar system collector array 1 C COLLECT 24 H Minimum temperature solar system collector ray 1 C RETURN Solar system return temperature
19. ight hand dial to the BASIC SET menu Press the right hand dial Turn the right hand dial to the LANGUAGE sub menu Press the right hand dial to change the language Select the language by turning the right hand dial You can select from the following English French Dutch Spanish Portuguese Italian Czech Polish Slovakian Hungarian Russian Greek Turkish Bulgarian Croatian Latvian Lithuanian Romanian Swedish Serbian Slovenian Danish Estonian Confirm the selection by pressing the right hand dial You go back to the basic display by pressing the Info button Operating Instructions BM Programming Module 3062600 201208 41 Basic settings COOLING FEN UN Factory setting OFF Setting range ON OFF 5 13 Selecting the cooling function with heat pump If linked to a Wolf heat pump and BKM cooling module the BM can be used to enable a cooling function for a heating circuit The cooling function only applies to heating circuits which have a separate programming module allocated to them via the address Cooling is enabled for a heating circuit if none of the heating circuits in the system calls for heating energy the relevant programming module is in summer mode and the actual room temperature is 2 the set room temperature for cooling 7 cooling temperature In addition the symbol xt is displayed in the programming module In automatic timer mode a time program or programmed switc
20. influence S Selecting the cooling function with heat pump Selecting timer programmes Setback mode Setting automatic timer mode Setting continuous operation mode Setting stand by mode Setting summer operation mode Setting the cooling temperature Setting the date Setting the day temperature Heating Setting the hot water temperature Setting the key lock Setting the maximum output mode Setting the reduced temperature reduction Setting the room influence Setting the setback mode Setting the time Setting the winter summer changeover Stand by mode Starting 1x DHW Starting heating Starting reduction Summer operation mode Switch times T Technical data Temporary room temperature adaptation Ww Warning notices Winter summer changeover 52 30 32 34 c 42 31 13 14 15 14 43 25 26 27 36 16 28 37 15 24 38 20 18 19 9 29 47 17 58 Operating Instructions BM Programming Module 3062600 201208 Alphabetical index Operating Instructions BM Programming Module 3062600_201208 59 Wolf GmbH Postfach 1380 84048 Mainburg Tel 08751 74 0 Fax 08751 741600 Internet www wolf heiztechnik de Operating Instructions BM Programming Module 3062600 201208 Subject to modifications
21. ing the right hand dial down for approx 10 seconds 50 Operating Instructions BM Programming Module 3062600_ 201208 Appendix Boiler HG status table Pini Explanation Notes 0 Standby 1 Emissions test mode Max 30 min 2 Soft start Approx 3 min 3 Heat demand heating mode 5 Heat demand with cycle block 6 Cycle block See HG 09 7 Frost protection central heating See A 09 8 Soft starter See HG 26 11 DHW drawing For combi boilers 12 DHW drawing run on 1 min 13 Minimum combi time Still in DHW mode 14 DHW quick start reheating See HG 11 15 Cylinder operation For boilers 16 Frost protection cylinder lt 5K 17 Pump run on cylinder See HG 19 18 Dry run Poss pump 19 dt output reduction Fan speed 20 Cylinder parallel mode See A 10 21 Max cylinder heating time exceeded See HG 20 MI 09 ap See HG 24 ol See HG 24 24 Off period flue gas monitoring 15 min Operating Instructions BM Programming Module 3062600_ 201208 51 Appendix Parameter overview basic settings A Individual Parameters Setting range Factory setting setting Time 0 to 24h Date 01 01 2011 to i 31 12 2099 Time programme 1 21 13 1 Temp day 5 to 30 C 20 C Reduced temperature 5 to 30 C 16 C Heating curve HC heating circuit 0 to 3 0 1 2 MI 1 7 mixer circuits 0 to 3 0 0 8 Room influe
22. is switched off in summer mode In the summer mode the BM programming module switches the hot water generation on or off in accordance with programmed switch times Within the switch times the circulation pump if fitted is switched on The frost protection function is active The pumps of the heating system are started at regular intervals in order to prevent the mechanical parts from seizing up gt Turn the left hand dial until the arrow is next to the Summer mode ET symbol 4 4 2 Setting continuous operation mode In continuous mode the heating and hot water generation are switched on continuously over a 24 hour period The heating heats up to the set room temperature day temperature The DHW oylinder is heated up to the set hot water temperature Within the switch times the circulation pump if fitted is switched on gt Turn the left hand dial until the arrow is next to the Continuous operation mode 73 symbol 14 Operating Instructions BM Programming Module 3062600 201208 Operation Heating Reduced temperature Hot water DHW ON Circulation Switch time Heating OFF Hot water DHW OFF Circulation OFF Frost protection active 4 4 3 Setting the setback mode In the setback mode the heating heats up to a set reduced temperature Within the switch times the DHW cylinder is heated to the set hot water temperature outside the switch time the DHW cylinder is n
23. me period has elapsed the boiler switches back to the previously set operating mode Within the switch times the DHW cylinder is heated up to the set hot water temperature gt Press the Reduce button gt Select the period in which the heating should heat in the setback mode by turning the right hand dial Setting range 0 23 hours or 1 30 days gt Confirm the time for setback operation by pressing the right hand dial After a few seconds the display switches back to the basic display In the status display the Setback mode symbol J or the Stand by mode symbol 5 flashes when the ECO RED function switches the boiler to the stand by mode gt To terminate the Reduce special function prematurely press the Heating button Operating Instructions BM Programming Module 3062600 201208 19 Operation 4 7 Starting the 1x DHW function The 1x DHW special function bypasses the programmed switch times and heats the DHW cylinder on a single occasion for one hour to the set hot water temperature e gt Press the 1x DHW button 1x6 After a few seconds the display switches back to the basic display In the status display the Hot water symbol Wh flashes al The DHW cylinder is heated up to the set hot water temperature for one hour C A gt To terminate the 1x DHW special function prematurely press the 1x DHW button 20 Operating Instructions BM Programming Module 3062600 201208 Ope
24. n gt Do not remove bridge out or deactivate any safety or monitoring devices gt You must rectify faults and damage that impair safety immediately Avoiding frost damage gt Make sure that the heating system remains in operation and that the rooms are adequately heated when you are away during frosty periods Operating Instructions BM Programming Module 3062600_ 201208 7 Equipment description 3 Equipment description The BM programming module is a control unit for controlling heating and hot water generation Six operating modes are available Automatic timer mode Heating at programmed times Hot water generation at programmed times Circulation pump at programmed times Summer mode Heating not in operation Hot water generation at programmed times Frost protection active Pump standstill protection active 4 Continuous mode 24 hour heating 24 hour hot water generation Circulation pump at programmed times Setback mode Heating at reduced temperature Hot water generation at programmed times Circulation pump at programmed times 4 Stand by mode Heating not in operation Hot water generation not in operation Frost protection active Pump standstill protection active 4 Flue gas test installed in boiler Full load operation for emissions measurement Operating Instructions BM Programming Module 3062600 201208 Equipment description QU xe
25. nce ON OFF OFF Winter summer 0 to 40 C 20 C changeover ECO RED 10 to 40 C 10 C Hot water temperature Free standing boiler 15 to 65 C 50 C Wall mounted boilers 15 to 65 C 50 C with cylinders Wall mounted 40 to 65 C 50 C combi units English Language Setting the English language Key lock ON OFF OFF Cooling function ON OFF OFF Cooling temperature 5 to 35 C 25 C Table A 3 Parameter overview basic settings 52 Operating Instructions BM Programming Module 3062600_ 201208 Glossary Glossary Anti legionella function Legionella are a type of bacteria which can cause serious illness Legionella can form and reproduce if tap water is exposed to long dwell times at 25 C to 50 C This can occur in DHW cylinders The anti legionella function can kill any bacteria in the hot water by short term heating to temperatures in excess of 65 C Cascade Acascade is a parallel arrangement of several boilers in order to achieve a higher overall output Circulation pump The circulation pump circulates the water heated in the DHW cylinder in a circulation pipe in order to be able to use hot water quickly at large distances from a central hot water generator In order to save energy you can switch the pump off during times at which no hot water is required Cylinder charging Cylinder charging signifies the heating up of an indirectly heated storage tank hot water heater To this end a
26. nstalled as a remote control the set room temperature only represents an approximate value Setting the room influence gt Press the right hand dial gt Turn the right hand dial to the BASIC SET menu gt Press the right hand dial If a heating circuit and one or more mixer circuits are connected e g radiator and underfloor heating then first select the relevant heating or mixer circuit gt Turn the dial to the HC or MK1 MK7 sub menu gt Press the right hand dial gt Turn the right hand dial to the RED TEMP sub menu gt Press the right hand dial to change the temperature gt Select the reduced temperature by turning the right hand dial gt Confirm the reduced temperature by pressing the right hand dial You go back to the basic display by pressing the Info button 28 Operating Instructions BM Programming Module 3062600 201208 Basic settings 5 6 Switch times The switch times are available in the automatic timer mode and Summer mode You can set the times at which the heating system heats to the desired room temperature day temperature You can programme times at which the DHW cylinder is heated to a specific hot water temperature You can programme times at which the circulation pump if fitted is switched on The switch times for the heating hot water generation and the circulation pump if fitted are set in two steps First decide whether the switch times are to be pro
27. ormation Symbol for a required action Warning notices in the text provide a warning of potential dangers before an action is started The warning instructions provide you with an indication of the potential severity of the danger by using a pictogram and a signal word 4 Operating Instructions BM Programming Module 3062600 201208 Notes concerning the documentation Picto Signal Explanation gram word Danger Danger to life or danger of A f severe injury Danger to life or risk of Danger severe injury from electric shock Warning Risk of minor injury Caution Potential material damage Tab 1 1 Meaning of warning notices 1 3 1 Structure of warning instructions The warning notices in this manual can be recognised by the pictogram a top line and a bottom line The warning notices are structured according to the following principle Signal word AN Type and source of the danger Explanation of the danger gt Instructions for action to avert the danger Operating Instructions BM Programming Module 3062600 201208 Safety and regulations 2 Safety and regulations gt The instructions in this chapter must always be followed 2 1 Intended use The Wolf BM programming module is used exclusively in connection with Wolf boilers and Wolf accessories The Wolf BM programming module is used to control central heating systems and central heating systems with hot
28. ot heated up Within the switch times the circulation pump if fitted is switched on gt Turn the left hand dial until the arrow is next to the Setback mode symbol 4 4 4 Setting stand by mode In stand by mode the heating and the hot water generation are switched off The circulation pump if fitted is switched off The frost protection function is active The pumps of the heating system are started at regular intervals in order to prevent the mechanical parts from seizing up gt Turn the left hand dial until the arrow is next to the Stand by mode symbol D Operating Instructions BM Programming Module 3062600_201208 15 Operation amp Heating ON Hot water DHW ON 4 4 5 Setting the maximum output mode The maximum output mode is only required for flue gas measurement In maximum output mode the heating system runs at maximum heating output full load operation In full load operation the heating is heated up to the maximum set temperature and the DHW cylinder is heated up to the set hot water temperature In full load operation the chimney inspector can carry out the necessary flue gas measurements The maximum output mode is ended automatically either after 15 minutes or after the maximum flow temperature is exceeded You can only activate the maximum output mode with the BM programming module if the module is installed in the boiler gt Turn the left hand dial until the arr
29. ow is next to the Maximum output mode symbol E 16 Operating Instructions BM Programming Module 3062600 201208 Operation 4 3 2 1 2 3 4 Setting range 4 to 4 in 0 5 steps 4 4 6 Temporary room temperature adaptation Using the right hand dial you can change the room temperature for a short period without having to change the day temperature This change raises or lowers the day temperature and the setback temperature gt Turn the right hand dial until the arrow is next to the desired temperature correction value 2 1 Correction by approx 1 C 0 2 a Correction by approx 1 5 C 0 xY If the correction is not adequate for your needs then adjust the day temperature Setting the day temperature If the room influence function is not set BM programming module installed as a remote control the set room temperature only represents an approximate value Setting the room influence Operating Instructions BM Programming Module 3062600_201208 17 Operation 1 HEATING 03 00 STO Factory setting 3 hours Setting range 0 23 hours or 1 30 days J 4 5 Starting the heating Use the Heating special function in order not to have to change the programmed switch times for the heating on public holidays days of sickness or in holiday periods The Heating special function bypasses all set time programmes or operating modes
30. pump if fitted circulates the hot water in the pipes v vvvvvvyv Press the right hand dial Turn the right hand dial to the TIME PROG menu Press the right hand dial Turn the right hand dial to the CIRCULATION menu Select the day day block by turning the right hand dial Press the right hand dial Select the switch time by turning the right hand dial Confirm the selection by pressing the right hand dial Set the start time 3 by turning the right hand dial Confirm the start time by pressing the right hand dial Set the end time by turning the right hand dial Confirm the end time by pressing the right hand dial You go back to the basic display by pressing the Info button Operating Instructions BM Programming Module 3062600 201208 35 Basic settings HEUS LOCK OFF Factory setting OFF Setting range ON OFF 5 7 Setting the key lock The key lock prevents inadvertent alteration of the settings on the BM programming module gt gt gt gt Press the right hand dial Turn the right hand dial to the BASIC SET menu Press the right hand dial Turn the right hand dial to the KEY LOCK sub menu Press the right hand dial to switch the key lock on or off Select the setting by turning the right hand dial ON key lock on OFF key lock off Confirm the setting by pressing the right hand dial The key lock is activated approx 1 minute after the las
31. ration 4 8 Displaying information Using the Info button you can display information concerning all available set actual temperatures burner starts and operating hours in addition to other system values The first value is displayed when you press the Info button If you press the Info button again or if you turn the right hand dial the following values are displayed provided that the relevant sensors are connected Only the values from connected components are displayed If additional BM programming modules are integrated in the Wolf control system or are installed as remote controls then the individual parameters are displayed e gt Press the Info button gt Press the Info button or turn the right hand dial to display further information An overview of the parameters that can be displayed can i be found in the appendix to this operating manual Operating Instructions BM Programming Module 3062600 201208 21 Basic settings 5 Basic settings Main menu Display DISPLAY BASIC SET TIME PROG Set actual EXPERT values RETURN Basic setting TIRE TEMP DAY DATE RED TEMP TINE PROG HEAT CURVE HE ROOM INFLU PIX VALVE 1 WS SUITCH ECO RED MIX VALVE 1 DHU TEMP LANGUAGE KEY LOCK COOLING FEN COOLING T Time programmes Time prog 1 2 HEATING HE RO FR DHU PIX VALVE 1 SA SU CIRCULATION muy VALVE 2 I I a PIX VALVE 7 Time prog 3 L
32. rcuit and one or more mixer circuits are connected e g radiator and underfloor heating then first select the relevant heating or mixer circuit gt Turn the dial to the HC or MK1 MK7 sub menu gt Press the right hand dial v Select the day day block by turning the right hand dial Press the right hand dial Select the switch time by turning the right hand dial Confirm the selection by pressing the right hand dial Set the start time 2X by turning the right hand dial Confirm the start time by pressing the right hand dial Set the end time by turning the right hand dial Confirm the end time by pressing the right hand dial vvvvvvyv You go back to the basic display by pressing the Info button 32 Operating Instructions BM Programming Module 3062600_201208 Basic settings Always programme the switch times one after the other Switch time 1 06 00 10 00 Switch time 2 15 00 22 00 Times which include midnight must be programmed in time programmes 1 and 2 per the following example The heating should run from 16 00 to 03 00 on the following day in time programme 1 This means that you should set the following times Switch time 1 00 00 03 00 Switch time 2 16 00 24 00 Ej Ej You go back to the basic display by pressing the Info button Operating Instructions BM Programming Module 3062600 201208 33 Basic settings SWITCH TIRE 1 05 00 1234567 UEU
33. rner Burner stage 2 active multi stage burner 12345 Number of boilers 12 Operating Instructions BM Programming Module 3062600_201208 Operation Heating Switch time Hot water DHW Switch time Circulation Switch time 4 3 Operating modes You can set various different operating modes 4 4 Setting automatic timer operation The automatic timer switches the heating the hot water generation and the circulation pump on and off at the programmed switch times Within the switch times in heating mode the heating system heats up to the set room temperature day temperature Within the switch times the DHW cylinder is heated up to the set hot water temperature Within the switch times the circulation pump if fitted is switched on gt Turn the left hand dial until the arrow is next to the Automatic timer mode symbol 20 C 16 C EE 0 00 6 00 22 00 24 00 Fig 4 2 Example of a switch time In the switch time from 6 00 to 22 00 the heating heats to the set room temperature day temperature in heating mode In the period from 22 00 to 6 00 the heating heats to the setback temperature Operating Instructions BM Programming Module 3062600 201208 13 Operation Heating OFF Hot water DHW Switch time Circulation Switch time e 3 Heating ON Hot water DHW ON Circulation Switch time 4 4 1 Setting summer mode The heating
34. saving effect by having to expend a large amount of energy in order to heat the rooms back up again Only if you are away for an extended period e g on holiday is it worth setting the setback temperature lower Circulation pump The circulation pump circulates the hot water in the piping network This ensures that hot water is immediately available at the draw off points Operating Instructions BM Programming Module 3062600_201208 45 Messages and faults SERVICE FAULT 04 Example 7 Messages and faults 7 1 Service After a specific time period which is set by your heating engineer the display on the BM programming module shows the SERVICE message gt Consult your heating engineer for the maintenance of your heating system 7 2 Fault A fault in the heating system can be detected by the illuminated ring on the control system flashing red The heating engineer can quickly identify the fault using a fault code table and the BM programming module gt Inthe event of a fault observe the instructions in the operating manual for your boiler gt Inthe event of a fault in your heating system consult your heating engineer 7 2 1 Message on the boiler Illuminated ring display Meaning Flashing green Ready mains switched on no heat demand Continuous Heat demand pump running green light burner off Yellow flashing Maximum output mode Constant yellow l
35. sired room temperature within the switching times with the day temperature Change the day temperature preferably using the temperature correction Room temperature temporary adaptation If the room influence function is not set BM programming module installed as a remote control the set room temperature only represents an approximate value Setting the room influence If the BM programming module is installed as a remote control then open up all the thermostatic valves in the room gt Press the right hand dial gt Turn the right hand dial to the BASIC SET menu gt Press the right hand dial If a heating circuit and one or more mixer circuits are connected e g radiator and underfloor heating then first select the relevant heating or mixer circuit gt Turn the dial to the HC or MK1 MK7 sub menu gt Press the right hand dial gt Turn the right hand dial to the TEMP DAY sub menu gt Press the right hand dial to change the temperature gt Select the day temperature by turning the right hand dial gt Confirm the day temperature by pressing the right hand dial You go back to the basic display by pressing the Info button 26 Operating Instructions BM Programming Module 3062600 201208 Basic settings 5 4 Setting the hot water temperature Using the hot water temperature function you can adjust the temperature to which the DHW cylinder is heated up to by the boiler Danger
36. t Press the right hand dial gt Turn the right hand dial to the BASIC SET menu gt Press the right hand dial gt Turn the right hand dial to the TIME menu gt Press the right hand dial gt Adjust the time by turning the right hand dial Turn slowly change the minutes Turn quickly change the hours gt Confirm the entry by pressing the right hand dial You go back to the basic display by pressing the Info button If the BM programming module is without power for longer than 48 hours then you will need to reset the time and day 24 Operating Instructions BM Programming Module 3062600_201208 Basic settings 5 2 Setting the date Setting the date This setting always follows the same pattern first select the day then the month and finally the year gt Press the right hand dial gt Turn the right hand dial until you reach the menu BASIC SET gt Press the right hand dial gt Turn the right hand dial until you reach the menu Factory setting DATE Setting range 01 01 2011 to gt Press the right hand dial 31 12 2099 gt Set the date gt Confirm the entry by pressing the right hand dial Return to the basic display by pressing the Info button Operating Instructions BM Programming Module 3062600_201208 25 Basic settings TEMP DAY eu Factory setting 20 C Setting range 5 30 C 5 3 Setting the day temperature Heating You set the de
37. t adjustment You go back to the basic display by pressing the Info button If the key lock is set then KEY LOCK appears in the display as soon as a key or a dial is actuated gt You can temporarily deactivate the key lock by pressing the right hand dial for about 1 second 36 Operating Instructions BM Programming Module 3062600_ 201208 Basic settings ROGA INFLU FF Factory setting OFF Setting range ON OFF 5 8 Setting the room influence The Room influence is only active if the BM programming module is installed as a remote control and if you have set the Room influence function The room influence should only be changed in consultation with your heating engineer The room influence function is used to compensate for room temperature changes caused by extraneous heat or cold e g direct sunlight stoves or open windows gt Press the right hand dial gt Turn the right hand dial to the BASIC SET menu gt Press the right hand dial If a heating circuit and one or more mixer circuits are connected e g radiator and underfloor heating then first select the relevant heating or mixer circuit gt Turn the dial to the HC or MK1 MK7 sub menu gt Press the right hand dial gt Turn the right hand dial to the ROOM INFLU sub menu gt Press the right hand dial to switch the room influence function on or off gt Select the setting by turning the right hand dial ON room in
38. t water charging solar cylinder 3 SOL STATUS 3 Anti legionella function solar cylinder 3 0 not successful 1 successful OUT TEMP Outside temperature C ES AVERAGE Outside temperature average C Outside temperature maximum value C 0 to 24 h ES MAX MIN Outside temperature minimum value C O to 24 h ROOM TEMP Room temperature ACTUAL value C Room temperature SET value C Table A 1 Display continued on next page Operating Instructions BM Programming Module 3062600_201208 49 Appendix Display Name ROOM TEMP 1 Room temperature ACTUAL value mixer circuit 1 2 7 C 2 7 Room temperature SET value mixer circuit 1 2 7 C MODE HC Heating circuit operating mode Sun Moon Stand by HEADER TEMP Header ACTUAL temperature C Header SET temperature C BOILER TEMP Boiler ACTUAL temperature C Boiler SET temperature C Mixer ACTUAL temperature 1 2 7 C a eee Mixer SET temperature 1 2 7 C 2 7 Mixer circuit operating mode Sun Moon Stand by RETURN Return ACTUAL temperature C STATUS HG Boiler status Operating manual for the boiler BURN RUN H Burner operating hours BURN START Boiler burner starts Table A 1 Display continued Only the values from connected modules mixer module MM cascade module KM solar module SM are displayed The displays can be reset to Zero by hold
39. u gt Press the right hand dial to change the temperature gt Select the temperature for the winter summer changeover by turning the right hand dial gt Confirm the temperature for the winter summer changeover by pressing the right hand dial You go back to the basic display by pressing the Info button 38 Operating Instructions BM Programming Module 3062600 201208 Basic settings ECO RED i0 Factory setting 10 C Setting range 10 40 C 5 10 Setting ECO RED Using the ECO RED temperature you can stipulate an outside temperature from which the heating is switched on or off in the setback mode The ECO RED setting should only be changed in consultation with your heating engineer gt Press the right hand dial gt Turn the right hand dial to the BASIC SET menu gt Press the right hand dial If a heating circuit and one or more mixer circuits are connected e g radiator and underfloor heating then first select the relevant heating or mixer circuit gt Turn the dial to the HC or MK1 MK7 sub menu gt Press the right hand dial gt Turn the right hand dial to the ECO RED sub menu gt Press the right hand dial to change the temperature gt Select the ECO RED temperature by turning the right hand dial gt Confirm the ECO RED temperature by pressing the right hand dial You go back to the basic display by pressing the Info button Operating Instructions BM
40. um heating output full load operation The maximum output mode is ended automatically either after 15 minutes or after the maximum flow temperature is exceeded Mixer circuit The mixer circuit is a heating circuit into which a mixer is fitted for temperature regulation of the heating water The mixer is fitted in the heating flow in order to regulate the flow temperature by mixing in the cooler return water Reduced temperature The reduced temperature is the value to which the set room temperature is reduced at times of low usage Setback mode In the setback mode the set room temperature is reduced to the reduced temperature at times of little use e g at night 56 Operating Instructions BM Programming Module 3062600_ 201208 Alphabetical index Alphabetical index A Automatic time operation mode 8 C Circulation pump times 35 Continuous mode 8 D Displaying information 21 E ECO RED ECO Reduction 9 Energy saving tips 44 Equipment description 8 F Faults 46 G General safety instructions 6 H Heating 9 l Intended use 6 K Key lock 9 M Maximum output mode 8 Menu structure 22 Messages 46 Oo Other applicable documents 4 Overview of the BM programming module 10 Operating Instructions BM Programming Module 3062600 201208 57 Alphabetical index P Parameter overview basic settings Pre programmed switch times Programming heating times Programming hot water times R Reduce Room
41. w which the boiler goes into the frost protection function If the outside temperature falls below the set value then the boiler circulation pump will run continuously If the boiler water temperature falls below 5 C then the burner switches on and heats up to the minimum boiler temperature Heating circuit A heating circuit is an enclosed system for heat distribution It consists of radiators or underfloor heating the associated valves and the pipes for the flow and return Heating curve The heating curve describes the relationship between the outside temperature and the flow temperature that is required to achieve the desired room temperature Heating mode In the heating mode the room temperature is held at around the day temperature value at times of high usage e g during the day Hot water generation The term hot water generation designates the heating of drinking water in a water heater This can be an instantaneous water heater a DHW cylinder an indirectly heated storage tank water heater or similar Operating Instructions BM Programming Module 3062600_201208 55 Glossary Key lock The key lock protects the BM programming module from inadvertent inputs and changes to stored values If the key lock is active the BM programming module will not accept any inputs Maximum output mode The maximum output mode is only required for flue gas measurement In maximum output mode the heating system runs at maxim
42. water generation Intended use includes the observance of the operating instructions and all other applicable documents Any other use in addition to this is considered to be non intended The manufacturer supplier shall not be liable for damage resulting from this The risk is borne entirely by the operator 2 2 General safety instructions The BM programming module must be installed and started up by a qualified heating engineer Electrical installation must only be carried out by qualified electricians Faults or damage to the BM programming module or the heating system must only be rectified by a qualified heating engineer 6 Operating Instructions BM Programming Module 3062600 201208 Safety and regulations Avoiding the risk of scalding Hot water temperatures in excess of 65 C can cause scalding When the anti legionella function is activated the DHW cylinder is heated to above 65 C for at least an hour With solar hot water generation the hot water temperature can rise to over 90 C gt Do not set the hot water temperature above 60 C gt Ask your heating engineer whether the anti legionella function is activated gt Ask your heating engineer when the anti legionella function starts gt Ask your heating engineer whether he has fitted a thermostatic water mixer to provide protection from scalding Avoiding malfunctions gt Only operate the system if it is in a technically perfect conditio

BM Programming Module Operating instructions

Contents

Download Pdf Manuals

Related Search

Related Contents