Operating instructions - Fimotec
Contents
1. MAINMENUE PARAMETER SENSOR 100 Ic OO MAINMENUE SENSOR 1 re SW SENSOR SG a EXIT Parameter PARAMETER Sensor 1 SENSOR 1 Oscillation amplitude sensor SW SENSOR SW SENSOR Ca PIECE COUNTER 2 Sle O MAINMENUE PIECE COUNTER ru ACTUATOR 1 RA Piece counter PIECE COUNTER ee EXIT MAINMENUE _ _ ACTUATOR 1 ENABLE EXIT ENABLE PASSWORD EIT Actuator 1 ACTUATOR 1 Enable ENABLE Password PASSWORD PASSWORD Factory settings DEFAULT Table 8 Main menu 4 2 7 1 FS 16 FS 18 SW Sensor Actuator 1 Call up the main menu Press the MENU button The FS 16 FS 18 has eight parameter blocks 0 7 in which rs different settings are stored and can Ext ser be called up again For branching to sensor menu see section 4 2 8 PARAMETER For branching to sensor menu see section 4 2 9 For branching to the piece counter menu see section 4 2 10 For branching to actuator menu see section 4 2 11 For branching to enable menu see section 4 2 12 For branching to password menu see section 4 2 13 MAINMEHNUE FACTORY DEFAULT SET Query whether the current settings should really be reset to the factory settings A socket is available for the actuator and SW sensor of FS 16 FS 18 The socket function can be defined via the main menu Screen display MAINMENUE SW SENSOR AC2. fimotec fischer Montagetechnik 4 2 Description of the user levels In this chapter the different user levels will be shown and described 4 2 1 Structure tree main menu MEIINMENUE Eu OFF DELAY ON Menu MAIHMEHNUE Parameter MAIHMEHUE eee MAIHMEHLE MAIHMEHLE 4 EXIT SET J DELAY OFF 3 PARAMETER SENSOR i Cr Cem Ti Te d Delay Off A d EEN as 1 EXIT ie exit i MAINMENUE MAIHMEHUE LOHHECT ee J EXIT J SET J SEHSOR gt SS EE nemmeueg TL SENSOR 3 kb Kb d d Ka rs WK exit ser JIL __MAINNENUE Connect ACTUAR OFF CONNECT ES REES saat MAIHMEHUE DELAY DN E EXIT SET ne SW sensor DELAY ON aa Delay On Ce CEKIT ser i 4 C EXIT ser ICTUATOR 1 5 a i Actuator 1 MAIHMEHUE Gene Sls SS DELAY OFF Delay Off a exit ser lt exit ser B vw La Actuator 2 DELAY OFF 2 83 Set L1 L2 L3 No of conveyor CH1 conveyor CH2 CONUEVOR r CH2 conveyor Mes CH3 conveyor Sie EH PANEL OH PASSWORD DEFAULT Dal set Default MAINMENUE ao PASSWORD OFF e exit ser KRRIRBDR wa e vs 3 HAIHMEHLIE FACTORY DEFAULT 7 Status as of 09 2012 Page 11 fimotec fischer Montaget
3. 320 Hz Resolution Steps of 0 1 Hz Save nominal value Pressing the SET button saves it The window will close Table 4 Nominal frequency specification menu 4 2 4 User level status 1 The Status 1 screen shows the channel properties The parameters are described in Table 5 Display field Shows the name of the user level Status display for channel 1 STATUS 1 ACT Channel 1 activated not activated Display channel activated SPR ACT iia RUN RUN active RUN inactive Display output not active PCS INT EXT Capacity specification Display internal INTERNAL EXTERNAL A1 A2 Link with actuator output Display CH1 linked with actuators 1 and 2 Table 5 Display status 1 Page 14 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 4 2 5 User level status 2 The Status 2 screen shows the sensor links and settings The structure of the Status 2 screen is described in Table 6 Screen display Description STATUS 2 Display field SIEHE Shows the name of the user level OFFIP2 D S1 Sensor status display Display S1 gt Sensor1 Sensor not active CH1 CH2 CH3 Shows the link with sensor 1 Display Sensor 1 linked with channel 1 S1 S2 S37 A1 and actuator 1 A3 OFF N O N C Sensor setting status Display Sensor 1 OFF switched off P2 Second nominal value spec Display Power 2 active D Time delay Display Time delay active STATUS 2 V but
4. If the device is not correctly connected this can lead to the failure or complete destruction of the device and the connected load 7 1 Power connection assignments Powe connection Designation Designation 50 Hz 60 Hz a 0 Mains output 1 230 V AC 2 0V PE BE Consumer output 1 Load 2 Load PE Protective ground conductor 6 3 A slow blow Status as of 09 2012 Page 29 EM l Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 8 Dimensions 9 Maintenance and care 9 1 Regular tests The devices are usually maintenance free The electrical equipment of the machines are still to be checked regularly by skilled electricians If it s dirty clean the touchscreen with a conventional window cleaner and a soft lint free cloth 9 2 Decommissioning and disposal The device is to be decommissioned by skilled electrical personnel while complying with the valid safety regulations The packaging of the converter can be recycled Please keep the packaging for later use Easily removable screw connections allow the device to be disassembled into its components These individual components can be recycled Please carry out disposal in agreement with the local regulations Problematic materials must not be thrown away in the normal waste Dispose of problematic materials properly safely and in an environmentally friendly manner Page 30 Status as of 09 2012
5. Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 10 Accessories and options 10 1 The plug connectors listed below are available as accessories Article number Mains output connection X10 91 3300 20 91 3300 70 91 3300 40 91 3200 60 91 3300 30 10 2 The connection lines and oscillation amplitude sensor listed below are available as accessories Article number 91 4301 20 91 4301 00 91 4301 10 91 4210 01 91 4210 02 91 4210 03 91 4210 04 91 4201 03 91 4201 04 Disable connection to a TSM 11 3m X23 91 4280 01 control Disable connection to aFSM 137 3m X23 91 4280 02 control or FS 16 FS 18 TD 16 control unit Disable connection to aFSM 137 5m X23 91 4280 03 control or FS 16 FS 18 TD 16 control unit Disable connection to a FSM 137 91 4280 04 control or FS 16 FS 18 TD 16 control unit amplitude sensor SWS 01 24 V e Y piece for connecting an 91 3900 02 oscillation amplitude sensor in combination with sorting air 24 V Connection X 91 4220 01 Sorting air valve 230 V FS 18 Festo MSUDK CB5K only Connection 3m A 91 4220 02 Sorting air valve 230 V FS 18 Festo MSUDK IB5K only Status as of 09 2012 Page 31
6. Montagetechnik 4 2 14 Channel menu CHANNEL MENU 1 CHANNEL MENU 2 CHANNEL MENU 3 The channel menus for power output 1 CH1 power output 2 CH2 power output 3 CH3 have the same structure The following Table 16 shows the structure Screen display Button Screen display ACTIVE Press the MENU button ee MENUE Set ramp For branching to the ramp menu see section 4 2 15 SET RAMP ww Type of setpoint The capacity setpoint is specified ES specification for the via the touchscreen capacity wW A POWER INPUT A The capacity setpoint is specified via the analog input Specification 0 10 V corresponds to 0 100 WK A The capacity setpoint is specified via the analog input Specification 4 20 mA corresponds to 0 100 SET Setpoint Setting the setpoint specification specification power 2 a for capacity 2 POWER 2 S setting range 0 100 ai k Output Setting the maximum capacity Ai l 1 S _ SET Er W A EXIT in D Current limit Setting for the maximum current on channel 1 POWER MAX Ca CURRENT LIMIT I tase Rs MENUE CHANNEL X Setting for the maximum current on channel 2 ll DN A MENUE CHANNEL Setting for the maximum current Er on channel 2 E A Table 16 Channel menu Page 24 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 4 2 15 Ramp menu Scr
7. CONNECT HME Off delay setting ACTUA OFF setting range 0 0 s 60 0 s EA E ll SET WK 3 SET J CONNECT Link actuator output X to sensor 1 Actuator output becomes active inactive when set delay times of sensor 1 have elapsed Link actuator output to channel 1 Actuator output becomes active when channel 1 is active and inactive when channel 1 is switched off Time delay Actuator output switch on delay a DELAY ON Actuator output becomes active DELAY OFF after 2 s when channel X is ee Ice SET exit switched on east Actuator output switch on delay Actuator output is active for 2 s before channel X is switched on Time delay Actuator output switch off delay Fa DELAY OFF Actuator output is active for 2 more DELAY OFF seconds after switching off channel Ki TA MAINMENUE Actuator output switch off delay Actuator output switches off 2 DELAY OFF 2 83 seconds before channel X is switched off Table 13 Actuator menu Page 20 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik The time delays for the actuator outputs can only be used if there is a link to an output channel CHANNEL X The following diagrams show the various switch on switch off delays for the actuator outputs Setting Delay On gt 0 s Delay On Channel X Actuator output X Time Setting Delay On lt 0 s Delay
8. On Channel X Actuator X Time Setting Delay Off gt 0 s Delay Off Channel X i Actuator Ge Time Setting Delay Off lt 0 s Delay Off Channel X i ActuatorX o Time If both actuator outputs are linked to the same channel X the delay times are executed as follows Setting Actuator 1 Delay On 2 0s Actuator 2 Delay On 5 0s Delay Off 3 08 Delay Off 4 0 2 05 5 08 4 0 S 3 08 Enable DT Channel Tu x Actuator Ir 4 Actuator GG geemeegeg 2 Time Status as of 09 2012 Page 21 EM j Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 4 2 12 Enable menu The following Table 13 shows the structure Screen display Button Screen display Press the MENU button INFO MENUE MAINMENUE Press V button until ENABLE appears ENABLE ru PASSWORD SG a E EXIT SET _ EL MAINMENUE Internal enable Activate internal enable ENABLE INTERN ee EXIT lt EXIT SET MAINMENUE Deactivate internal enable INTERN OFF EXIT SET DN External enable Deactivate external enable ENABLE EXTERN E a2 EXIT J C SET EXIT EXIT DN DN External enable switching status N O normally open active when EXTERN N O wr contact closed a EXIT SET J External enable switching status N C normally closed active EXTERN N C 52 when contact open Ca Ceat ser Table 14 Enable menu 4 2 13 Passw
9. in the intended construction machine and who manufacture the ready to use version Designation for the structural layout of the user interface Touch sensitive screen display with operating function Status as of 09 2012 Page 3 EM l Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik Table of contents 1 PRODUCT OV Al 6 1 1 Scope Of delivery ccccccsssscccccceeececccaeseececccsuuseceeeeuaueeceesseauseceeesuasceeessaaseceeessaaeceesseaaeeeeeessaasesessssaaeeeess 6 1 2 Bye rel cits e EE 6 1 3 Available ACCESSOMES ODIIONS u een ee een een 6 1A PROD GNSS ae Bun E a a en anna 7 1 4 1 ETC 7 1 4 2 MONO E EEN 7 E SC E ae tt 7 7 EE 7 2 SAEBERINEOBMATION ccccccaccesecarccareeareeaeeearecarecarecanccaeecaesaareacrentenaseeaeeentecarecaeeenaecaaecaareaareansennreaes tonsil 8 2 1 ETO Lg EE 8 2 2 Baer eaman a eee ees Ml ee 8 2 2 1 MASON dl eine SEENEN a o e EE 8 3 INSTALLATION EEN eege 114 40 1 co lonesococoneconssonedce ooc oc Ae 9 3 1 Each area STallEN N annan EEN 9 3 2 KEES CONNEC olni aseene EE WEEN EE BEEN 9 3 3 BS seilanganeonveyOr Connection ME VE nen annn 9 3 4 FUSE TE UE o nun EEN nen EE 9 4 Oaa KEE o A EE 10 4 1 Explanation of the button and display fields 2000000420000RRRnennnnnnnnnnnnnnnnnnnnnnnnnnnnennnne nennen 10 2 Desa PEON CL INE user EVS coocoo A A o o MRPEBRRRRRRERRRRR 11 4 2 1 iruciu
10. input The enable input is for switching the oscillating conveyor connected to the FS 16 FS 18 on and off without power The enable must be designed via a potential free contact e g external switch 5 3 Sensor input The load output of the FS 16 FS 18 can be switched on off via a sensor e g filling level sensor Via the global menu the on and off delay times can be set within a range between 0 60 sec The resolution is 0 1 seconds In the following Figure 3 the time curve is shown graphically Zeitverlauf Kanalausgang in Abh ngigkeit des Sensoreingangs Leistung VA F rderleistung P2 aktiv DELAY OFF SOFTSTOP DELAY ON SOFT START Zeit s 0 605 0 105 0 605 0 105 Figure 3 Time curve for load output sensor input 5 4 SW sensor input The oscillation amplitude sensor input of the FS 16 FS 18 is also connected to input X24 For the function see section 4 2 9 Main menu SW SENSOR Page 26 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 5 5 Actuator output The actuator output of the FS 16 FS 18 is a digital output which is freely selectable See section 4 2 7 Main menu ACTUATOR The output has a voltage of 24 V and a load current of max 700 mA The output is short circuit proof A constant overload should be avoided however OV means that the actuator output is switched off 24 V means that the actuator output is switched on The FS 18 has a separ
11. the current limit ERR CURRENT LIMIT 1 amp 2 amp 3 Channel outputs 1 2 and 3 are at the current limit INFO MENUE Table 19 Current limit error 4 3 3 No SW sensor connected Screen display ERR NO SW SENSOR is displayed when no SW sensor is detected at the input Cause of error OFF No sensor connected INFO J MENUE Cable breakage Defective sensor Table 20 SW sensor error 4 3 4 Current supply interruption Screen display This screen appears if the current supply to the FS 16 FS 18 is interrupted e g due to a power THE DEVICE failure or switching off the power supply The FS 16 FS 18 switches off the power output IS SHUTTING DOWN Channel 1 Channel 2 and Channel 2 in this state The last operating state is saved and is continued when the voltage supply is switched on Table 21 Current supply interruption error Status as of 09 2012 Page 25 EM j Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 5 Description of control I Os FS 16 FS 18 2 Signal X22 Sensor 1 24 V DC 2 0V 4 Signal X23 Operation 1 N O status output 2 Changer 3 N C X24 Actuator SWS 1 24 V DC 2 Actuator output 3 0 V 4 SW sensor de S Zen FS 18 only 2 0 V 5 1 Operating status The operating output is designed as a potential free changeover contact with a maximum loadability of 230 V AC 6 A 5 2 Enable
12. 0 s When the sensor is active the power of the defined channel 1 channel 2 or channels 1 amp 2 are reduced to zero When the sensor is active the power from the defined channel 1 channel 2 or channels 1 amp 2 are adapted to the specified setpoint 2 Sensor X has a link Sensor X is linked with channel 1 Page 17 EM j Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 4 2 9 Oscillation amplitude sensor menu The following Table 11 shows the structure Screen display Button Screen display MENU Press the MENU button SW SENSOR Press the V button until SW SENSOR appears Press button select SW sensor SW sensor not active SWS OFF Cl 4 EXIT SET MAINMENUE SW sensor linked to channel 1 SWS CH NNEL 1 ges LU EXIT SET Table 11 Oscillation amplitude sensor menu 4 2 9 1 Oscillation amplitude sensor function For this procedure it is assumed that the parameters for the oscillating conveyor are correctly set Procedure 1 Switch off FS 16 FS 18 power output with the OFF button 2 Connect the oscillation amplitude sensor from the company FFM article designation SWS 01 to the FS 16 FS 18 3 Inthe oscillation amplitude sensor menu select the corresponding channel 1 4 Switch on the FS 16 FS 18 power output with the ON button 5 On the user level of the selected channel set the nominal capacity and confirm with the SET button The SW sensor now re
13. Operating instructions Status 2012 09 Operating instructions fimotec fischer Montagetechnik Frequency control devices FS 16 FS 18 for oscillating conveyor Art no 90 0210 50 FS 16 Art no 90 0210 52 FS 18 fimotec fischer GmbH amp Co KG Friedhofstra e 13 D 78588 Denkingen Tel 49 0 74 24 88 4 0 Fax 49 0 74 24 88 4 50 E mail post fimotec de Internet www fimotec de EM l Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik The duplication sharing or use of this documentation or its contents is only allowed with written permission Violations result in liability for damages All rights reserved including such which arise from granted patents or registration of a utility patent or design Copyright fimotec fischer GmbH amp Co KG 2012 Page 2 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik Information and explanations Target group These operating instructions will help you to use the described product safely and as intended They are directed toward qualified skilled personnel Qualified personnel are people who have been authorized by persons responsible for the safety of the system to execute the required activities and are able to recognize potential dangers and avoid them based on their training experience and instruction as well as their knowledge of standards regulations accident prevention regulat
14. TUATOR 1 SW SENSOR ACTUATOR 1 Button Screen display A Table 9 SW Sensor Actuator 1 Page 16 Status as of 09 2012 Operating instructions FS 16 FS 18 4 2 8 Sensor menu The following Table 10 shows the structure EMm fimotec fischer Montagetechnik Screen display Button Screen display STATUS READY ON OFF INFO J MENUE MAINMENUE SENSOR 1 W SENSOR SENSOR 1 rs Ba STATUS On delay DELAY ON DELAY ON Fa DELAY OFF J LESIT J SET DN MAINMENUE DELAY OFF rea Off delay DELAY OFF Za SET J _ MAINMENUE SENSOR ON e 4 Exit SET Sensor is active SENSOR ON Link CONNECT Table 10 Sensor menu Status as of 09 2012 Press the MENU button Press button V until the desired sensor appears Select the desired sensor SENSOR OFF EA o SET SENSOR N O S SE Ts SENSOR N C EA MAINMENUE DELAY ON oS us J EXIT J SET J DELAY OFF GME FOWER 2 0H a te EXIT J SET J MAINMENUE CONNECT OFF sa L e _ P CHANNEL 1 ie J EXIT Sensor input not active Sensor input active Switching status N O normally open active when contact closed Sensor input active Switching status N C normally closed active when contact open On delay setting setting range 0 0 s 60 0 s Off delay setting setting range 0 0 s 60
15. ate actuator output with 230 V AC 3 A Status as of 09 2012 Page 27 EM fimotec fischer Montagetechnik 6 Technical data Supply voltage Supply voltage tolerance Mains frequency Output current CH1 FS 16 Output current CH1 FS 18 Output voltage Enable Load current sensor 1 Load current actuator Status output potential free changeover contact Operation Display Type of protection Permissible ambient temperature Permissible relative humidity Dimensions EMC Page 28 Operating instructions FS 16 FS 18 230 VAC 115V AC other voltages possible after consultation 10 50 60 Hz other frequencies possible after consultation GA 8A 0 210 V Contact 24 V DC 24 V DC each max 100 mA 24 V DC each max 700 mA FS 18 230 V AC max 3A Changeover contact 230 VAC 6A Touchscreen LCD display 128x64 pixels IP54 5 C to 45 C max 95 non condensing approx h 185 mm x w 109 mm x d 115 mm Interference emissions and noise immunity in acc with EN 61000 6 x Noise immunity in acc with EN 61000 4 x Electrostatic discharge strength ESD IEC EN 61000 4 2 HF irradiation IEC EN 61000 4 3 Burst IEC EN 61000 4 4 Surge IEC EN 61000 4 5 HF current infeed IEC EN 61000 4 6 Voltage drop voltage interruption IEC EN 61000 4 11 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 7 Terminal assignments
16. display field on the touchscreen via which the displayed function is controlled Function Button as switch Ifthe button is not actuated as a switch this is shown with a blue background see ON button in Figure 1 If the button is actuated as a switch this is shown with a white background see OFF button in Figure 1 The button as a switch works with positive button pressure That means that when the button is pushed by pressing on the touchscreen the respective function is executed immediately Function Button as push button Ifthe button is not actuated as a push button this is shown with a blue background see INFO and MENU buttons Figure 1 If the button is actuated as a push button this is shown as being pressed shifted back see gt button Figure 1 The button as a push button works with negative button pressure This means that when the button is pressed the respective function is only executed when the button is released again STATUS 2 Display field with status lo display Figure 2 Display field with status display Display field with status In this display field the current status of the respective parameter is visualized display Ifthe status is inactive the contents are shown with a blue background Ifthe status is active the contents are shown with a white background Page 10 Status as of 09 2012 Operating instructions FS 16 FS 18 EM
17. echnik Operating instructions FS 16 FS 18 Structure tree channel menus 1 2 and 3 STATUS READY 4444 44 RMEHUE CHAHHEL wv SET RAMP POWER INPUT MEHUE CHAHHEL A FOWER 2 rel Ca FEHUE CHAHHEL X FOWER HAX ili CURRENT LIMIT 4 2 2 Starting level Current limit CHAMHEL ACTIVE me A ACTIVE LC MENUE CHANNEL CU SOFT START 8 13 U Cexr ser J mue CHANNEL TL SOFT STOP ae Cex Cer 20 MEHUE CHAHHEL Soft start Soft stop SOFT START SOFT STOP me CHANNEL x PANEL INPUT C MENUE CHANNEL ILL e e OO MENUE CHANNEL XII POWER MAX vr MENUE CHANNEL X LI CURRENT u LU On the starting level the user can switch the FS 16 FS 18 on and off The structure of this screen is described in Table 1 STATUS READY 4444444 INFO MENUE Seana Table 1 Starting level Page 12 Status bar The status bar shows the status of the FS 16 FS 18 Display Ready for operation Status bar The stars represent external input signals gt or External enable Sensor 1 Sensor 2 Sensor 3 External parameter line BitO External parameter line Bit1 External parameter line Bit2 External parameter line SET Ai Ze Ai Ze Ai Ze Ai Ze Ki Ze Ki Ze Ki Ze ON OFF button The power outputs are activated via the ON button The power outputs are deactivat
18. ed via the OFF button Display ON button not actuated OFF button actuated INFO button MENU button gt button Branching to the FS 16 FS 18 information screen Branching to the main menu Branching to the user levels Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 4 2 3 User level channels 1 2 3 The user levels channel 1 channel 2 and channel 3 are identically structured In the following Table 2 the structure is described based on the user level channel 1 Display field Shows the name of the user level ACTIVE button Button for activating the channel Display channel is not active ACTIVE button Button for activating the channel 390 0Hz Display channel is active POWER button 3 Is branched to the screen for specifying the capacity gt FREQUENCY button el 1 Is branched to the screen for specifying the nominal frequency Display fields 0 100 Display of the current capacity after enable signal Display of the current nominal frequency 15 320 Hz Variant Solo Duo channels 1 and 2 15 320 Hz Variant Trio channel 1 20 320 Hz Channels 2 and 3 button Branching to the previous level MENU button Branching to the channel menu gt button Branching to the next level E Table 2 Display of user levels channels 1 2 and 3 4 2 3 1 Capacity nominal value specification In this menu the capacity can be set via the t
19. een display Button Screen display MENUE CHANNEL xX Soft start ramp MENUE CHANNEL 4 Soft start ramp setting SOFT START ey _ setting range 0 1 s 10 0 s SOFT START KS c WH SET Soft stop ramp Soft stop ramp setting SOFT STOP ey setting range 0 1 s 10 0 s SOFT STOP SIE u c SET Table 17 Ramp menu 4 3 Error display Description of the errors shown on the screen 4 3 1 Overtemperature Screen display When the maximum permissible temperature of the FS 18 FS 16 is exceeded this is displayed on the screen In the status bar ERR OVERHEAT will appear Cino J MENUE gt In addition the current temperature is schematically displayed via a white bar Once the ee a temperature is in the normal range white bar gone the previous operation is continued Table 18 Overtemperature error 4 3 2 Current limit Screen display Screen description If the current is exceeded at the channel output the respective display appears in the status bar ERR CURRENT LIMIT 1 Channel output 1 is at the current limit Er ERR CURRENT LIMIT 2 Channel output 2 is at the current limit ERR CURRENT LIMIT 3 Channel output 3 is at the current limit ERR CURRENT LIMIT 1 amp 2 Channel outputs 1 and 2 are at the current limit ERR CURRENT LIMIT 18283 ERR CURRENT LIMIT 1 amp 3 Channel outputs 1 and 3 are at the current limit ERR CURRENT LIMIT 2 amp 3 Channel outputs 2 and 3 are at
20. gulates to the specified nominal capacity If this is to be changed the procedure should be executed again starting with step 5 When the control range is exceeded this is displayed under Status 2 of the SW sensor ATTENTION In software version 1 0 only possible via internal setpoint specification Page 18 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 4 2 10 Piece counter menu The following Table 12 shows the structure Screen display Button Screen display Press the MENU button a MAINMENUE PIECE COUNTER Press the V button until PIECE COUNTER appears PIECE COUNTER in ACTUATOR 1 SS a ae EXIT k Status Switch off piece counter ee EXIT EXIT SSE ROIHREHUE Switch on piece counter PIECE COUNT ON os 4 EXIT SET J STATUS STATUS PIECE COUNT OFF TOTAL RESET SS S EXIT All piece counters are reset _____ MAINMENVE Reset ____MAINMENUIE TOTAL RESET TOTAL RESET TOTAL RESET SC EXIT Table 12 Piece counter menu Status as of 09 2012 Page 19 EM j Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 4 2 11 Actuator menu The following Table 13 shows the structure Screen display Button Screen display ETATUS READY MENU Press the MENU button WE ACTUATOR 1 Press V button until ACTUATOR 1 appears Select the desired actuator Link
21. ions and operating conditions definition of skilled personnel according to IEC 364 Read these operating instructions before you install the device use it or carry out work on it Also pass on these operating instructions to other users Definition of the warnings and symbols Warnings are indicated by danger symbols and signal words The table shows what hazards and possible consequences the symbols signal words and colours indicate Signal word Directly threatening danger Death or extremely serious injuries Dangerous situation Potential death or extremely serious injuries ee Dangerous situation Minor to Minor to moderately serious injuries serious injuries ACHTUNG Risk of property damage xz _ to the machine its environment and the product Warnings can also have other warning signs Example Warning of electrical current These symbols indicate the type of hazard Term definitions User Persons who use the device installed by the manufacturer in its ready to use version Designation for the image visible within the touchscreen Designation for key fields on the touchscreen Electromagnetic compatibility with electrical and electromagnetic influences Skilled personnel Qualified personnel with the appropriate education training and experience Device Designation in these operating instructions for the oscillating conveyor control unit FS 16 FS 18 Machine manufacturer Persons who install the device
22. nsumer Mains input voltage monitoring Type of protection IP54 1 4 2 Output data Frequency range 15 Hz to 320 Hz The frequency range is adjustable in steps of 0 1 Hz for all variants Power adjustable from 0 to 100 in steps of 1 Soft start ramp soft stop ramp adjustable from 0 to 10 seconds Switch on and off delay in range from 0 to 60 seconds 1 4 3 Inputs Enable input for switching on off without power Sensor input with switch on off delay in range from 0 to 60 seconds SW sensor input 1 4 4 Outputs Operating notification relay contact 230 VAC 6A changeover contact Consumer output for oscillating conveyor Actuator output 24 V DC Actuator output 230 V AC 3 A only on FS 18 Status as of 09 2012 Page 7 EM l Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 2 Safety information 2 1 Intended use The FS series devices are pieces of electrical equipment and are intended for use in supply mechanisms or automation systems The devices are designed for the regulation and control of oscillating conveyor systems The electrical components listed here are called devices in the industrial parlance but are not devices which can be used or connected or machines in the sense of the Device safety law the EMC law or the EC Machinery Directive but components Only when these components are integrated in the construction of the machine manufact
23. o with the proper use of tools and the use of personal safety equipment The Emergency Stop mechanisms must remain in effect in all operating modes Unlocking the Emergency Stop mechanisms must not result in uncontrolled reactivation 2 2 1 Transport and storage Problem free and safe operation of this device require proper transport storage setup and installation as well as careful operation and maintenance The device must be protected against mechanical impacts and vibrations during transport and storage Protection against moisture water and impermissible temperatures see chapter 6 Technical data must also be guaranteed Page 8 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 3 Installation If the device is not correctly connected this can lead to the failure or complete destruction of the device and the connected load 3 1 Hardware installation The FS 16 and FS 18 devices are designed for external installation outside of a control cabinet and have IP54 protection If the device is mounted on a mounting plate made of metal it can be installed with its entire area in contact with the plate or with spacers If the device is mounted to a thermally non conductive surface it is to be mounted at a distance of at least 10 mm from its surface 3 2 Mains connection The mains must be connected according to the valid regulations It is connected via the attached Sch
24. ord menu The following Table 15 shows the structure Screen display Button Screen display Press the MENU button INFO MENUE PASSWORD Press the V button until PASSWORD appears re EXIT SET Password not active If the FS 16 FS 18 has password PASSWORD OFF d e Ac protection this must be entered to deactivate LOW PROTECTION 7951 HIGH PROTECTION 6842 Low password LOW PROTECTION protects all protection WE e UU oC input parameters such as power LOW SS etc LO The ON OFF function is not ENE PROTECTION E en ne protected with this type of protection Password for LOW PROTECTION Page 22 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik Screen display Button Screen display 7951 High password HIGH PROTECTION all inputs to 77 rotection the device are protected c SET PROTECTION E5 SET 6842 STATUS LOGGED This is displayed when the password has been correctly input As long as one is logged in there will be no password query Table 15 Password menu Note regarding password protection Password protection active Before changing input parameters the password must be entered according to the type of protection A correctly entered password is active for two minutes after the last press of a button Status as of 09 2012 Page 23 EM j Operating instructions FS 16 FS 18 fimotec fischer
25. ouchscreen Sue aE Set the capacity On the main screen press the gt button Press once to change channel 1 Press twice to change channel 2 Press three times to change channel 3 Now the screen shown on the left appears for channel 1 2 or 3 Call up screen for the power Press the POWER button CHANNEL To increase power Press or hold the A button To reduce power Press or hold the V button POWER Attention If the maximum capacity POWER MAX is limited in the channel menu this limit is the maximum for 100 Then the following function applies Capacity 0 lt POWER MAX value Once input has been made the value is saved by pressing the SET button and the window is closed Table 3 Capacity nominal value specification menu Status as of 09 2012 Page 13 EM j Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 4 2 3 2 Nominal frequency specification In this menu the nominal frequency can be set via the touchscreen RE aS STS Set nominal frequency On the main screen press the gt button Press once to change channel 1 Press twice to change channel 2 Press three times to change channel 3 Now the screen shown on the left appears for channel 1 Call up screen for the frequency Press the FREQUENCY button Frequency increase Press or hold the A button Frequency reduction Press or hold the V button Specification of the nominal frequency from 15 20
26. re ires Man OU asisas ee Eee E ee 11 Structure tree channel menus 1 2 and 3 12 En ue 1G EE 12 4 2 38 User level channels 1 2 3 WEEN i ccssencaenecerccungasesecocectugaaeceee diMsenguaeccencecangusecceaecsanacdngscdeccerseceescours 13 4 2 4 User level oz ZS WW AS WA Se e nn ae unnanununanununnnnnnn 14 4258 User level satus D A DW qe WW 98 SS BB E eera 15 4 2 68 User level statuses Wd T A Z WA es ee Se ee Ee nennen 15 Men eelere E 16 42 7 Main un 16 e We cial log el EE EENG CHE PEE EET 17 4 2 98 BOsailation affelitude sensorgen u ER gn ER Re RE A I e 18 42 18 Wieeefeoumier mfnu BW A ent Z DW 8 WM mm E a 19 4210 Betuaior Mena MM DW A e eB ee A A WW WW cere cee 20 42 12 Enable De lee sete eg De 22 A213 Password o En E EEN TI EE 22 4 2 14 Channel menu CHANNEL MENU 1 CHANNEL MENU 2 CHANNEL MENU 37 24 Gen SAID Eegeregie 25 AS EON al Ee E 25 BON e SI OTIC alle E 25 432 et C Il EE 25 4 3 3 No SW sensor connected cece cc ceeccceeececeeeeeeeeeeecueueeeeueeeueueeeauueaeeaeeaueueaeauueaeaeuauaeusuueeuaecauaeeeeeeeeeueueeeuaueaeeeeesadeueueceueueeeasaeeeenes 25 Ae TEUrreNESURDIYINIE del Eee Goantie taal coceus E E 25 5 DESCRIPTION OF CONTROL I OS FS 16 FS 18 u0 2u0020000000000n00nnnunnnun nun nun nun nun nun nun nun nun 26 sH e die E TEE 26 ANS WO EE 26 e oS EE 26 Page 4 Status as of 09 2012 Operating instructions FS 16 FS 18 EM 5 4 9 9 10 10 1 10 2 fimo
27. tec fischer Montagetechnik DIV SEN Or ID ee EE 26 erte g QUTOUL uses innara n nin EEE ena EEE EEEE AKEN ENEE E EEEE EA EEEE ENA EES 27 TECHNICAL DATA E 28 TERMINAL PG NIE AR 29 Power CONNECTION assignmmenmts rrenen nn reene 29 DIMENSION LE 30 MAINTENANCE AND CARE ee ee 30 Ref e ernennen EEE 30 DECOMMISSIONING and dsposa 30 ACCESSORIES AND OPTIONS AALEN AEAEE ALA EEA ANAE eani ans 31 The plug connectors listed below are available as accessories cccccseecceeseeceeeeeeaeseeseeeeesaeeeeseeeess 31 The connection lines and oscillation amplitude sensor listed below are available as accessories 31 ACCESSORES AND OPTIONS ir eene enen A x 4 14 31 Status as of 09 2012 Page 5 EM l Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 1 Product overview 1 1 Scope of delivery FS 16 FS 18 control unit with software V1 0 Operating instructions 1 2 Device versions The FS series devices are microprocessor controlled 1 phase frequency converters for sinusoidal actuation of consumers with variable frequency and amplitude 1 3 Available accessories options Oscillation amplitude sensor type SWS 01 Page 6 Status as of 09 2012 Operating instructions FS 16 FS 18 EM fimotec fischer Montagetechnik 1 4 Properties 1 4 1 General Consumer output Parameterization via parameter blocks LCD touchscreen for operation Overcurrent limit for the co
28. ton Branching to next sensor status 1 1 CH1 A1 oeeo C SWS Sensor status display Display SWS Sensor not active OFF CH1 CH2 Indicates the assignment for Display Assignment channel 1 CH3 the oscillation amplitude sensor MIN MAX Display for control range Display Control range at maximum overshoot button Branching to the previous level cH1 MAx Exit button Branching to start screen a J EXIT Table 6 Display status 2 4 2 6 User level status 3 The Status 3 screen shows the operating hours counter and the piece counter The structure of the Status 3 screen is described in Table 7 l STATUS 3 Display field 999999 h Shows the name of the user level 999999 h STATUS 3 Indicates the operating hours during which the device was switched on FSi 999999 l l l h 9999991h d Indicates the operating hours during which channel 1 was active V button Branching to next level EFEEEEITT EEEE QUANTITY Indicates the total piece number that the sensor counted Reset only possible in the main menu STATUS 3 QUANTITY Piece counter with reset function QUANTITY RESET button Branching to the previous level EXIT Exit button Branching to start screen Table 7 Status 3 display Status as of 09 2012 Page 15 EM fimotec fischer Montagetechnik Menu description 4 2 7 Main menu Operating instructions FS 16 FS 18 Screen display Button Screen display STATUS READY
29. uko power plug All touchable electrically conductive housing parts must be grounded according to the valid regulations The connection must be made with at least a 1 0 mm line cross section 3 3 Oscillating conveyor connection This is connected via the X11 socket The pin assignments are as follows Pin 1 Connection for load Pin 2 Connection for load PE Connection for the ground protection conductor The oscillating conveyors are connected to these connections 3 4 Fuse protection The fuse protection on the primary side depends on the line cross section However it must be designed to have a B6 line protection switch at minimum The devices are also protected with internal fuses Caution Leakage currents against PE might occur due to EMC related suppressor components These are harmless however when an industry standard RCD switch is used with a tripping current of 0 3 A Status as of 09 2012 Page 9 EM i Operating instructions FS 16 FS 18 fimotec fischer Montagetechnik 4 Operation The device is operated via a touchscreen The corresponding function is executed by touching the respective field on the touchscreen with a finger or blunt object 4 1 Explanation of the button and display fields STATUS READY Figure 1 Screen description mea Denon OOOO O Oo Status display field In the status display field the menu names and error messages are shown Button The term button designates the
30. urer is the ultimate mode of operation defined The machine manufacturer is responsible for making sure that the construction meets the existing legal regulations 2 2 Basic safety information The following warnings both serve for the personal safety of the user as well as the safety of the described products and the devices connected to them Non observance can lead to death serious bodily injury or property damage DANGER Life threatening danger due to electric shock Even after the device is put out of operation by disconnecting the voltage there is still dangerous electrical voltage on the internal circuit parts Disconnect the device from the supply voltage before any intervention Before opening the device wait for at least 5 minutes until the residual voltage has dissipated Check to make sure there is no voltage before any intervention Only skilled electricians may work on electrical equipment Before commissioning make sure that the voltage supply agrees with the nominal values of the device Check the electrical equipment of the machine regularly Deficiencies such as loose connections damaged or scorched lines must be fixed immediately Observe the valid accident prevention and safety regulations for your application In particular observe both the general and the regional installation and safety regulations for working with dangerous voltages e g EN 50178 as well as the regulations having to d
Download Pdf Manuals
Related Search