Home

Operating Instructions - IS Intelligent

image

Contents

1. Check if the connection contacts are clean If untidy clean them up with a little alcohol Switch on the mobile and connect the PhoneGuard Cable black GND brown input red output Getting started all models Your mobile phone must be switched on and properly registered in the radio network so that the PhoneGuard can operate Even with the PhoneGuard plugged in you can use your mobile phone for telephone calls or sending text messages The PhoneGuard is operative as soon as it is connected to the mobile phone interface In the case of GPRS compatible mobiles de activate this function and set the data transfer rate to 19 200 bps Please refer to the mobile phone operating instructions for information on how to proceed Otherwise the PhoneGuard requires no specific settings required to be made on the mobile phone IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany A Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Now communicate to the PhoneGuard which functions you wish to use This is done exclusively via SMS using one of the following three procedures a The simplest option is to send the SMS configuration commands from the mobile to the mobile itself where the PhoneGuard is plugged b Send the SMS configuration commands from another mobile phone to the mobile phone plus PhoneGuard c Send the SMS configuration commands from the Internet for exam
2. PIR sensor This sensor detects changes in infrared radiation which occurs when there is movement by a person or an object which is different in temperature from the surroundings The PhoneGuard checks the movement in the specified detection range standard horizontal 100 and vertical 82 spot horizontal 38 and vertical 22 In the case of a detected movement the alarm text is sent via SMS to the entered SMS numbers first telephone calls are made thereafter IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 16 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Activating and De activating Motion Alarm Function To activate the motion alarm function send the following SMS to the mobile phone plus PhoneGuard SET ALARM ON zzzz The PhoneGuard confirms with the following SMS PhoneGuard Alarm function activated To de activate the motion alarm function send the following SMS to your mobile phone plus PhoneGuard ASET ALARM OFF zzzz The PhoneGuard confirms with the following SMS PhoneGuard Alarm function de activated Entering Motion Alarm Text You can determine the text which is sent via SMS n the case of an alarm To change the standard text send the following SMS to the mobile phone plus PhoneGuard SET OPEN TEXT lt ttt gt zzzz replacing ttt with your own text for example Movement in the entrance Example SET OPEN TEXT lt Move
3. protection zone by walking to all those places that you wish to include n ie Perg zone As you walk along the PhoneGuard will make up a list of all radio cells that the mobile phone was logged into during recording When the protection zone function is activated the PhoneGuard checks whether it is able to identify the cell in which it is at that particular moment and will alert you if it cannot do so Starting Continuing and Stopping Protection Zone Recording To start recording the protection zone send the following SMS to your mobile phone plus PhoneGuard IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 10 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de SET ZONE START zzzz The PhoneGuard confirms with the following SMS PhoneGuard Definition of protection zone started Now you walk to all places which you wish to include in the protection zone After returning to the starting point you must stop recording Send the following SMS to your mobile phone plus PhoneGuard SET ZONE STOP zzzz The PhoneGuard confirms with the following SMS PhoneGuard Definition of protection zone stopped Exactly which radio cells the mobile phone logs into depends on many technical aspects and environmental influences To avoid false alarms we recommend recording the protection zone over a prolonged period If for example you intend to record the rou
4. PhoneGuard to ensure that nobody else except you has access to it The factory set PIN number is 0000 when supplied To change the PIN number send the following SMS to your mobile phone plus PhoneGuard SET PIN zzzz mmmmmm ZZZZ 1234 for example is the PIN number you selected mmmmmm 800A8C for example is the factory set Master PIN which you receive along with your PhoneGuard Example SET PIN 1234 800A8C e Letters in a PIN must always be written in capitals e If a wrong PIN has been transferred an error message is sent by the PhoneGuard PhoneGuard PIN wrong IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 9 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de e If the PIN has not been transferred an error message is sent by the PhoneGuard PhoneGuard PIN missing Listen Function allmodels This function enables you to hear voices n the area surrounding the mobile phone plus PhoneGuard i e you can listen in to a room thereby safeguarding it You must activate this function first via SMS and then you can call the mobile phone This feature allows you to listen n to a s tuation while t s however not possible to manually accept a call Such features are emergency functions perhaps capable of saving lives or which help to protect your property Therefore you as a user is obliged to observe the laws applicable in the country the PhoneGuard
5. VIB TEXT lt ttt gt zzzz Replace ttt with your own text Example SET VIB TEXT lt Alarm Vehicle No 123 is in motion gt zzzz The text must start and end with inverted commas but they should not be included within the text They will not be sent when the text is transmitted in the case of an alarm Max 128 characters are available for the text message Factory set the text is as follows PhoneGuard Motion alarm triggered Setting Vibration Alarm Delay The vibration sensor of the PhoneGuard is very sensitive and therefore the potential for false alarms is very high For this reason you can determine yourself when an alarm is to be triggered Because of the potential risk of frequent alarms minimal vibration will not trigger the alarm According to the standard configuration the vibrations must persist for at least 10 seconds To change the alarm delay send the following SMS to the mobile phone plus PhoneGuard IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 14 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de SET VIB DELAY a b zzzz replacing a and b with a figure between 1 and 99 Example SET VIB DELAY 5 60 0000 e a defines the time in seconds during which the vehicle is exposed to vibrations until the PhoneGuard identifies this as an alarm situation e b defines the time delay in seconds which elapses before the alarm message is sent I
6. alarm If you want to store less than three telephone numbers just ignore the rest of the PHONE commands If you want to replace a telephone number just send a new one If you want to delete a telephone number send a 0 instead of the telephone number Example SET PHONE1 491721234567 zzzz e 49 is the international country code for Germany e xxx 172 for example is the code of your mobile phone network or area code of your local telephone network WITHOUT the preceding 0 e yyyyyyy 1234567 for example is the mobile phone number or your telephone number e 7222718 the PhoneGuard PIN e In case of registering a wrong telephone number typing a character than a figure for example the PhoneGuard will respond with an error message PhoneGuard Syntax error in address number We recommend also activating the call function SMS and call as an SMS may be delayed as it travels through the network until reaching your mobile phone gt Repeat Call If a telephone number is busy or nobody is answering the phone it is possible to call this number several times To define the repeat call send the following SMS to your mobile phone plus PhoneGuard SET REDAILLING w zzzz Replacing w with a figure between 0 and 9 specifies the number of repeat calls Example SET REDAILLING 1 zzzz When supplied to the customer the repeat call number is set to 0 Changing PIN Number all models First change the PIN number of your
7. workmanship o fS Intelligent Systems or its authorised service company was not notified by the Customer of the defect within thirty 30 days after the appearance of the defect within the warranty period e the Product was not returned to S mtelligent Systems or its authorised service company within thirty 30 days after the appearance of the defect within the warranty period e the Product serial number has been removed erased defaced altered or is illegible e the defect was caused by a defective function of the cellular network or the mobile phone e the defect was caused because the Product was not employed for its intended use e the software of the Product requires upgrading as a result of modified network parameters mobile phone firmware parameter for the usage of locating services To claim this warranty the Customer shall present either a legible and non modified original warranty card which clearly indicates the name and address of the seller dealer the date and place of purchase the product type and the serial number or alternatively submit a legible and non modified original purchase receipt which contains the same information if such purchase receipt is presented to the seller dealer of the Product This warranty is the Customer s sole and exclusive remedy against S nteliigent Systems and lS intelligent Systems sole and exclusive liability against the Customer for defects or malfunctions of the Product This warranty re
8. I Intelligent ae h BR i Operating Instructio Contents Oase 2 Saleky TS Erie HOS ee een 2 ee ee 3 a e E E E E ee en en ne A 3 Quick Start Nokia BRS oo eccsccecceeeeeeeeeeeeeeeeeeesssaaaaeeeeeeseeeeeeeeeeeeeeeeeaaaeaaaaaas 4 Getinge sid ee ee ae 4 Command Summary nee ee ee 5 Registering Telephone Numbers 20000000022eeeneeeeeeeenennnnnnnnnnnnnnnnnnnnnnnnnnneneeenennnnen 8 Changing PIN Number En ea 9 Listen Function Teenie 10 Protection Zone Function RRBBBBBBBBBBBBMM 0000 c ccccccccccccccccssssessesssssseeeeeeeeeeeeeesessesseeegeeeeeseeeess 10 Vibration Alarm Function Theft Protection EEE eeeeeeeeeeeeeeeeeeeeneneeeeeeennnn 14 Contact Alarm Function esse 00 0 ccccsssseeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaaeas 15 Motion Alarm Function Modo SEERE aaeoa 16 Output switch Function Modo e eee 18 Keep Alve F nction Tr a u a 19 Inquiring about Serial Number Ts 22222222020000000000000nsnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnen 19 Reverting to Default Settings EEE 0 0 0 ccc ccecccsssesserseeneeeeeeeeeeeeeeeeeeeeeseeeeeeeesaaaaas 19 Mobile Phone Location ww 2222222222000000000000eennnnnnnnnnnnnnnnnnnnnnnneennnnnnnnnennen 19 Mobile Phone Operating Period Power Supplies EEREER 19 ADDED D POPE nee ne een reinen 2 More Information Www intelligent systems de cccccccccccc
9. anty period shall continue for the remaining part of the s x 6 month period and otherwise remain unaffected During the warranty period mtelligent Systems or its authorised service company will repair or replace at 48 Amtelllgent Systems sole discretion a defective Product S Amtelligent Systems will return the repaired Product or another Product to the Customer in good working condition All parts or other equipment for which replacements have been provided shall become the property of IS Intelligent Systems A repaired or replaced Product will not be given a prolonged or renewed warranty period This warranty will not cover painted housings or other similar personalised parts This warranty does not apply to deteriorations due to normal wear and tear This warranty shall further not apply if e The defect was caused by the fact that the Product has been subjected to use in contradiction with the owner s user manual rough handling exposure to moisture or dampness extreme thermal or environmental conditions or rapid changes in such conditions corrosion oxidation unauthorised modifications or connections unauthorised opening or repair repair by use of unauthorised spare parts misuse improper installation accidents forces of nature spillage of food or liquid influence from chemical products or other acts beyond the reasonable control of IS Intelligent Systems unless the defect was caused directly by defects in materials design or
10. ccccccccceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 23 Safety Instructions Your PhoneGuard has been designed and manufactured with great care and should be handled equally so Following the instructions below will help you to prevent your warranty term ceasing prematurely and ensure that you are pleased with your product for many years Please observe the following instructions when using the PhoneGuard e Observe all safety instructions given by the mobile phone manufacturer e Make sure the PhoneGuard is fully inserted into the mobile phone handset until it clicks e Do not subject your mobile phone handset and PhoneGuard to any mechanical stress e Keep the PhoneGuard out of children s reach e Store the PhoneGuard in a dry place Humidity fluids or any other moisture contains minerals which can lead to corrosion of the electronic circuits e Do not use or store the PhoneGuard in dusty or dirty environments e Do not store the PhoneGuard in hot environments High temperatures may reduce the service life of electronic equipment instruments deform certain synthetic materials or cause them to melt e Do not store the PhoneGuard in cold environments When the PhoneGuard heats up to its normal operating temperature humidity may develop inside which can damage the electronic circuit boards e Do not try to open the PhoneGuard If handled improperly the unit can be damaged e Do not drop the PhoneGuard or subject it to impac
11. e integrated output you can switch external devises like lamps sirens and heaters To switch an output permanently on send the following SMS to the mobile phone plus PhoneGuard SET SWITCH ON zzzz To switch an output permanently off send the following SMS to the mobile phone plus PhoneGuard SET SWITCH OFF zzzz In both cases the PhoneGuard confirms with the following SMS PhoneGuard Switch was toggled For certain applications it is necessary that the switch close or open just for a short time pulse function To switch an output on for a pulse send the following SMS to the mobile phone plus PhoneGuard SET SWITCH ON FOR t zzzz e t defines the pulse duration in seconds After this interval the switch goes back in the previous state The length of the time interval can be set anywhere between 0 and 120 seconds To switch an output off for a pulse send the following SMS to the mobile phone plus PhoneGuard SET SWITCH OFF FOR t zzzz In both cases the PhoneGuard confirms also with the following SMS PhoneGuard Switch was toggled The output port of the PhoneGuard is a so called open collector output The term open collector typically refers to a transistor output where the collector output of the transistor is not connected to a positive voltage Since a transistor used n outputs is a saturated switch the collector needs to be connected to a positive external voltage to complete the transistor circuit IF you are not fa
12. ection zone list e aaaaa bbbbb etc are codes of radio cells in the protection zone list Changing Protection Zone List You can change the protection zone list to suit your requirements by adding or deleting a few or more cell identities To add radio cell codes to the protection zone list send the following SMS to the mobile phone plus PhoneGuard SET ZONE LIST aaaaa bbbbb ccccc ddddd zzzz e aaaaa bbbbb ccccc ddddd are the cell codes in the protection zone list Max 23 cell codes can be transferred in one SMS These must always have five digits If required complete the code with preceding zeros It 1s absolutely important to respect the semicolon at the end of the list before the PIN zzzz To delete cell codes from the list send the following SMS to the mobile phone plus PhoneGuard SET ZONE CLEAR aaaaa bbbbb ccccc ddddd zzzz e aaaaa bbbbb ccccc ddddd are the cell codes in the protection zone list Max 23 cell codes can be transferred in one SMS They must always have five digits If required complete the code with preceding zeros It is absolutely important to include the semicolon at the end of the list before the PIN zzzz IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 13 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Vibration Alarm Function Theft Protection model 2 The theft protection function operates with a vibration senso
13. ent systems de Registering Telephone Numbers allmodels In order that the PhoneGuard can inform you in case of an event or an emergency it is required to register telephone numbers through which you can be reached You can be informed through two methods e via SMS to a mobile phone or landline number e viaanormal call to a mobile phone or a landline number In both cases you can register up to three telephone numbers into your PhoneGuard Additionally you can enter up to three SMS numbers into your PhoneGuard Always start with the number through which you can best be reached Registering SMS Numbers To be informed via SMS send the following messages which communicate your personal telephone numbers to your PhoneGuard SET SMS 1 99xxxyyyyyyy zzzz for the 1 telephone number to which an SMS will be sent SET SMS2 99xxxyyyyyyy zzzz for the 2 telephone number to which an SMS will be sent SET SMS3 99xxxyyyyyyy zzzz for the 3 telephone number to which an SMS will be sent If you want to store less than three telephone numbers just ignore the rest of the SMS commands If you want to replace a telephone number just send a new one If you want to delete a telephone number send a 0 instead of the telephone number Example SET SMS1 491721234567 2222 e 49 is the international country code for Germany e xxx 172 for example is the code of your mobile phone network or the area code of your local
14. er Registering In 1 2 or 3 storage place 99 int country code SET PHONEn xxx network or area code yyy your phone no zzzz PIN 99XXXYVVVY ZZZZ lt lt SET REDIALLLING w zzzz zzzz PIN ou PIN EE SONI mmm Master PIN a a 2 SET SIEBEN ON 22212 t between 1 and 999 t 0 is de activated zzzz PIN Sal ALIVE t zzzz En eC GET SERIAL NUMBER SET RESET zzzz IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 5 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Protection Zone Functions PZF ul JE SET ZONE START zzzz SET ZONE STOP zzzz SET ZONE CONT zzzz SET ZONE ON OFF zzzz PZT Alarm Text ttt SMS Text max 128 character within inverted commas SET ZONE TEXT lt ttt gt zzzz zzzz PIN GET BTS zzzz GET ZONE LIST zzzz Change Protection Zone List a b c d cell codes max 23 cell codes in one SMS 5 digits 3 SET ZONE LIST a b c d zzzz with preceding zeros zzzz PIN Delete cell codes a b c d cell codes max 24 cell codes in one SMS 5 digits SET ZONE CLEAR with preceding zeros zzzz PIN a b c d 3ZZZZ wd De Vibration Alarm Function VAF nfefe ey activating de activating zzzz PIN SET ALARM ON OFF ZZZZ VAF Alarm Text ttt SMS Text max 128 characters within inverted commas SET VIB TEXT lt ttt gt zzzz I zzzz PIN VAF Alarm Delay a Lapsed time before alarm 1 99 sec SET VIB DELAY a b zzz
15. ey should not be included within the text They will not be sent when the text is transmitted in the case of an alarm Max 128 characters are available for the text message When supplied the text is as follows PhoneGuard Protection zone was left Inquiring about Current Radio Cell Identity If you wish to purposefully influence the contents of the protection zone list or use the cell identity for another purpose you can find out about the coding of the radio cell the mobile phone plus PhoneGuard is in at that point Send the following SMS to the mobile phone plus PhoneGuard GET BTS zzzz The PhoneGuard will answer with messages in the form of PhoneGuard cell ID LAC aaaaa CI bbbbb aaaaa is the location area code and bbbbb is the cell identity coding used n the protection zone list Inquiring about Protection Zone List You can access the radio cell coding contained in the protection zone list To do this send the following SMS to the mobile phone plus PhoneGuard GET ZONE LIST zzzz Depending on the quantity of radio cells stored the PhoneGuard will answer by sending up to 6 messages in the form of PhoneGuard Cell list n aaaaa bbbbb ccccc ddddd IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 12 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de e n gives the current number of messages containing the coding of the radio cells in the prot
16. f you get into your own vehicle you have 65 seconds to remove the PhoneGuard from your mobile phone in the shown example The factory set time delay a is 10 seconds and the time delay b is 20 seconds Contact Alarm Function models 4 6 10 22 The Contact Alarm Function operates with externals contacts bare cable end models or with magnetic contacts The PhoneGuard checks the state of the contact and depending on the PhoneGuard model compares it with a certain alarm condition Different alarm conditions are pre defined in factory See below The PhoneGuard type which comes with magnetic contact will for example respond to the opening of a contact opening of a door The PhoneGuard with stripped cable connection however will respond to the closing of the contact If both switching modes are required the PhoneGuard can trigger an alarm on both opening AND closing of the contact In the case of an alarm the alarm text is sent via SMS to the entered SMS numbers first telephone calls are made thereafter Activating and De activating Contact Alarm Function To activate the contact alarm function send the following SMS to the mobile phone plus PhoneGuard SET ALARM ON zzzz The PhoneGuard confirms with the following SMS PhoneGuard Alarm function activated To de activate the contact alarm function send the following SMS to your mobile phone plus PhoneGuard SET ALARM OFF zzzz The PhoneGuard confirms with the fol
17. is utilised and to rule out any misuse resulting for example from the careless use of your PhoneGuard PIN Activating Listen Function To activate the listen function send the following SMS to your mobile phone plus PhoneGuard SET LISTEN ON zzzz The PhoneGuard confirms the command with the SMS PhoneGuard Listen function is activated After activating the listen function the ring tone of your mobile phone plus PhoneGuard will be switched off and the PhoneGuard will automatically accept the following call to your mobile if it is made within 15 minutes for the models 108 002 and 108 008 and for all other 30 minutes If you want to use this function then a call transfer to another number must not be programmed on your mobile See page 8 Protection Zone Function models 2 8 You should use this function if you want to be alerted as soon as a person or a mobile object leaves a zone pre defined zis nd a zone comprises the rad o coverage areas of all those places that er you choose to be included in the protection zone and in whose lg ARE immediate proximity the rad o cells of your mobile phone De network are located Depending on the coverage range of the individual mobile phone cells the protection zone radius comprising school or home for example may vary between less than 100 metres in villages or towns and up to several kilometres A in the country As with a tape recorder you can record the Fra Re a
18. itted in the case of an alarm Max 128 characters are available for the text message When supplied the text is as follows PhoneGuard Contact was closed Setting Contact Alarm Configurations You can determine whether you want to be informed upon the opening of the contacts the closing of the contacts or in both cases It is also possible to configure the time interval after which the PhoneGuard will then repeat its alarm message Send the following SMS to the mobile phone plus PhoneGuard SET DETECT s r zzzz e s defines the alarm configuration 1 for contact closed 2 for contact opened and 3 for contact opened AND contact closed e r defines the time in seconds after which the alarm message is repeated or a telephone call is made if the contact is repeatedly in the defined state The length of the time interval can be set anywhere between 10 and 120 seconds Example SET DETECT 1 90 zzzz An alarm SMS will be sending if the contact closed after a delay time of 90 seconds e The factory set configuration of the PhoneGuard with stripped cable connection is contact closed s 1 The time delay r is 60 seconds when supplied e The factory set configuration of the PhoneGuard with magnetic contact is contact opened s 2 The time delay r is 60 seconds when supplied Motion Alarm Function models 12 14 16 18 The Motion Alarm Function operates with the smallest available Passive Infrared Motion
19. lligent Systems reserves the right to make changes to and improvements on any of the products described in this document without prior Under no circumstances shall mtelligent Systems be responsible for any loss of data or income of any special incidental consequential direct or indirect damage howsoever caused The contents of this document are provided as is Except as required by the applicable law or jurisdiction no warranties of any kind either express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose are made in relation to the accuracy reliability or contents of this document 4 Antelllgent Systems reserves the right to revise this document or to withdraw it at any time without prior notice Certain products are not readily available in all regions Please contact your nearest IS Intelligent Systems authorised dealer or representative More Information www intelligent systems de Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates No representation or warranty is given and no liability is assumed by GmbH with respect to the accuracy or use of such information or infringement of patents or other intellectual property rights arising from such use or otherwise No licenses are conveyed implicitly or otherwise under any intellectual property rights The l
20. lowing SMS PhoneGuard Alarm function de activated Entering Contact Alarm Text You can determine the text which is sent via SMS in the case of an alarm A distinction is made between contact opened and contact closed To change the standard text for contact opened send the following SMS to the mobile phone plus PhoneGuard SET OPEN TEXT lt ttt gt zzzz replacing ttt with your own text for example Unauthorised opening of house apartment door Example SET OPEN TEXT lt Unauthorised opening of house apartment door gt zzzz IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 15 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de The text must start and end with inverted commas but they should not be included within the text They will not be sent when the text is transmitted in the case of an alarm Max 128 characters are available for the text message When supplied the text is as follows PhoneGuard Contact was opened To change the standard text for contact closed send the following SMS to the mobile phone plus PhoneGuard SET CLOSE TEXT lt ttt gt zzzz replacing ttt with your own text for example power break down sector 5 Example SET CLOSE TEXT lt Power break down sector 5 gt 0000 The text must start and end with inverted commas but they should not be included within the text They will not be sent when the text is transm
21. ments in the entrance gt zzzz The text must start and end with inverted commas but they should not be included within the text They will not be sent when the text is transmitted in the case of an alarm Max 128 characters are available for the text message When supplied the text is as follows PhoneGuard Motion alarm triggered Setting Motion Alarm Configurations You can determine whether you want to be informed upon movement in the detection area or no movement in the detection area It 1s also possible to configure the time interval after which the PhoneGuard will then repeat its alarm message Send the following SMS to the mobile phone plus PhoneGuard SET DETECT s r zzzz e s defines the alarm configuration 2 for movement e r defines the time in seconds after which the alarm message is repeated or a telephone call is made if the contact is repeatedly in the defined state The length of the time interval can be set anywhere between 10 and 120 seconds Example SET DETECT 2 90 zzzz An alarm SMS will be sending if movement is detected after a delay time of 90 seconds e The factory set configuration of the PhoneGuard is s 2 The time delay r is 60 seconds when supplied IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 17 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Output switch Function models 24 26 28 36 38 With th
22. miliar with this technique contact us for further support IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 18 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Keep Alive Function allmodels This function enables you to receive text messages at regular intervals that confirm that the PhoneGuard is still operational To set this function sends the following SMS to your mobile phone plus PhoneGuard SET ALIVE t zzzz the values for t between 1 and 999 t set to 0 will de activate the function e t determines the frequency in hours with which the PhoneGuard informs you via SMS that it is operational At the same time it sends information on the battery capacity PhoneGuard Keep alive message Battery capacity 80 Inquiring about Serial Number all models To inquire about the serial number of the PhoneGuard send the following SMS to the mobile phone plus PhoneGuard GET SERIAL NUMBER The PhoneGuard will answer via SMS in the form of PhoneGuard serial number 0001 01 01 Reverting to Default Settings all models To re set all parameters to the default settings send the following SMS to the mobile phone plus PhoneGuard SET RESET zzzz All user defined parameters are re set to defaults this also applies to the User PIN The protection zone list as well as user definable alarm texts will be deleted 0000 is the factory set PhoneGuard PIN when sup
23. ne plus PhoneGuard SET ZONE ON zzzz The PhoneGuard confirms with the following SMS PhoneGuard Protection zone monitoring started Now the PhoneGuard will check whether the radio cell into which the mobile phone is logged is contained in its list If not you will be informed via SMS or telephone call IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 1 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de If you want to use the protection zone function again after an alarm message then you must re activate it with the command SE ZONE ON zzz or remove the PhoneGuard from the mobile phone and plug it in again b To de activate the protection zone monitoring function send the following SMS to the mobile phone plus PhoneGuard SET ZONE OFF zzzz The PhoneGuard confirms with the following SMS PhoneGuard Protection zone monitoring stopped The pre defined protection zone remains stored and can be re activated at any time Entering Protection Zone Alarm Text You can determine the text that is sent via SMS in the case of an alarm To change the standard text send the following SMS to the mobile phone plus PhoneGuard SET ZONE TEXT lt ttt gt zzzz replace ttt with your own text for example Warning John has left the area Example SET ZONE TEXT lt Warning John has left the area gt zzzz The text must start and end with inverted commas but th
24. ogo and name are registered trademarks of S Intelligent Systems GmbH in Europe and other countries All rights reserved All other trademarks mentioned herein are the property of their respective companies IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 3 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de
25. p Germany 3 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de You will get back a confirming text message To protect your privacy you may choose to have every command authorized with a Pin number For more information please refer the detailed operating instructions Cable black GND brown input red output Quick Start Nokia all models PhoneGuard will delete all your SMS Messages on your SIM card Save all important messages before you start 1 Switch off your mobile phone and attach the PhoneGuard to the mobile phone and then switch it on again 2 To activate the alarm send the text message SET ALARM ON from that mobile phone that should be called in case of an alert to the mobile phone to which you attached the PhoneGuard Wait until the PhoneGuard has send a confirming text message PhoneGuard Alarm function activated in 30 seconds 3 To de activate the alarm send the following text message to the mobile phone with connected PhoneGuard SET ALARM OFF You will get back a confirming text message PhoneGuard Alarm function de activated To protect your privacy you may choose to have every command authorized with a Pin number For more information please refer to Changing PIN Number all models e Ifthe PhoneGuard does not read a particular message the following procedure is followed Remove the PhoneGuard from the mobile phone Switch off the mobile
26. places all other watranties and liabilities whether oral written non mandatory statutory contractual in tort or otherwise S Amtelllgent Systems is in no event liable for any incidental consequential or indirect damage costs or expenses Neither is S mteffigent Systems in any event liable for any direct damage costs or expenses if the Customer is a legal person Any change or amendment to this warranty requires JS Intelligent Systems prior written consent IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 2 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Warranty Certificate PLEASE USE BLOCK LETTERS TO FILL IN THE FORM Customer s name Customer s address Customer s telephone number Date of purchase Day Month Y ear Model Product serial number look into manual or ask for via SMS Place of purchase Dealer s Name Dealer s Address Telephone Number Stamp amp Signature Copyright Intelligent Systems All rights reserved Ver 1 3 Reproduction transfer distribution or storage of part or all of the contents of this document in any form without the prior written permission of JS Amtelllgent Systems is prohibited Other product and company names mentioned herein may be trademarks or trade names of their respective owners 1S Intelligent Systems operates a policy of continuous development Therefore IS Inte
27. ple to the mobile phone with the PhoneGuard We recommend proceeding according to a or b as the PhoneGuard is then able to return an error message if a mistake is made when entering the command Make sure that for ALL SMS commands sent to the PhoneGuard you use your PhoneGuard PIN so nobody else but you has access to the settings The factory set PhoneGuard PIN number is always 0000 Change this first following the description on page 9 The PhoneGuard reads and deletes only those messages from your mobile s SIM card which are addressed to it All other messages remain stored Make sure your SIM card s memory is not already full as otherwise your mobile cannot receive any further messages If you view the messages on your mobile which were addressed to the PhoneGuard it will not be able to read them anymore Delete the messages and re send SMS commands ensuring that the PhoneGuard is plugged in Switch off all ring tones and the vibrator if you wish the PhoneGuard to be silent Command Summary all models In this chapter all commands for the PhoneGuard Family are listed You can use this as a short reference guide and of course if you are familiar with programming electronic devices you can skip reading the following chapters General Functions SUT IE SMS number Registering n 1 2 or 3 storage place 99 int country code SET SMSn 99xxxyyyy zzzz xxx network or area code yyy your phone no zzzz PIN Telephone numb
28. plied Mobile Phone Location all models Network provider offers various options for mobile phone location Refer to your local network provider for more information Mobile Phone Operating Period Power Supplies all models The PhoneGuard takes the energy needed for its functions from your mobile phone automatically adapting to one of two possible modes e PhoneGuard with external power supply e PhoneGuard without external power supply PhoneGuard with external power supply Depending on your PhoneGuard variant it may be equipped with an additional connection for a mobile phone charger An external energy source is always useful when you wish your PhoneGuard s operating period to be longer than the normal standby period of your mobile phone When powered from an external energy source the PhoneGuard is always in Power On mode and therefore responds immediately to incoming SMS configuration commands IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 19 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de The PhoneGuard will inform you via SMS in the event of a breakdown in the external power supply and will automatically change to the energy saving mode var ant with external power supply only PhoneGuard without external power supply The PhoneGuard is designed to use very little energy from your mobile phone s battery The PhoneGuard
29. r integrated into the PhoneGuard All you have to do is to connect the PhoneGuard to your mobile phone and hide both in the boot of your car for example or under the seats Then you will have a certain time see below to leave your car before the sensor is activated and the alarm is set Make sure your mobile phone plus PhoneGuard is not left somewhere in the vehicle where it is easily visible as if the mobile phone is switched off or the PhoneGuard removed no information can be transferred to you As soon as you get into your vehicle again unplug your PhoneGuard or switch off your mobile phone You have a limited time to do this Activating and De activating Vibration Alarm Function To activate the theft protection function send the following SMS to the mobile phone plus PhoneGuard SET ALARM ON zzzz The PhoneGuard confirms with the following SMS PhoneGuard Motion monitoring started To de activate the theft protection function send the following SMS to the mobile phone plus PhoneGuard SET ALARM OFF zzzz The PhoneGuard confirms with the following SMS PhoneGuard Motion monitoring ceased It is sufficient to activate this function once as long as your PhoneGuard is always plugged in or taken out in time Entering Vibration Alarm Text You can determine the text which is sent via SMS in the case of an alarm caused by vibration To change the standard text send the following SMS to the mobile phone plus PhoneGuard SET
30. sed commands in your mobile phone How to do this please refer to the user manual of your mobile phone e Commands can be typed in small or capital letters PhoneGuard does not make difference between small or capital letters what make easier entering the commands e Unknown commands are acknowledged by the PhoneGuard with the error message PhoneGuard Unknown command e If you are using this manual in an electronic version you can click on the page numbers in the table of contents and in the text or on several links in the document to move fast to the desired text Quick Start Siemens PhoneGuard will delete all your SMS Messages on your SIM card Save all important messages before you start l Switch your mobile phone on Delete all SMS Attach the PhoneGuard to the mobile phone After a few seconds a message PhoneGuard 1s activated appears on the display 2 Send the text message Set Alarm on from that mobile phone that should be called in case of an alert to the mobile phone to which you attached the PhoneGuard Wait until the PhoneGuard has send a confirming text message PhoneGuard Alarm function activated in 30 seconds To generate a call in case of an alert the sensor contact at the attached PhoneGuard has to be activated closed 3 To de activate the alarm send the following text message to the mobile phone with connected PhoneGuard Set Alarm off IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottro
31. takes the energy needed for its functions from your mobile phone It is designed to use very little energy from your mobile phone s battery Nevertheless your mobile phone stand by period will be reduced which means that your mobile phone will need charging more frequently It is not so much the PhoneGuard that is to blame but rather the energy requirement of the mobile itself when operated with external components such as the PhoneGuard With no external power supply the PhoneGuard operates in the energy saving mode It can change from this to the Power On mode for about 15 minutes for models 108 002 and 108 008 and 30 minutes for all other models if the following conditions apply e after the PhoneGuard has been plugged into the mobile phone e after a configuration command has been received via SMS e after an alarm condition has appeared e inthe event of a power break down applies to variants with external charger only To what extent the mobile phone stand by period is reduced depends on the manufacturer and the model it is less affected on modern mobiles The PhoneGuard however checks the status of your mobile phone battery capacity When the battery capacity falls to 20 a warning message is sent in the form of PhoneGuard Battery warning charge battery Thereafter the PhoneGuard will adopt a battery protection mode This means that the PhoneGuard remains inactive up until it is plugged back into the mobile phone Appro
32. te your child takes to school every day then continue recording for a whole week whenever your child walks to school If your mobile phone has to be re charged in the meantime just plug in your PhoneGuard afterwards to continue recording A protection zone may comprise a maximum of 128 radio cells If the protection zone list is full the PhoneGuard will send the following SMS PhoneGuard Protection zone list full Recording must then be stopped using the command SET ZONE STOP zzzz gt An alarm message may be sent e if a radio cell of your mobile phone network provider is no longer operative and the mobile phone logs into a cell which has not been listed during recording e if the network provider installs new radio cells e if the network provider changes the radio cell coding If you have already recorded a protection zone then this one will be replaced if you use the Start command If you do not want this to happen use the Continue command To expand the protection zone by one or two more locations without deleting the protection zone recorded so far send the following SMS to the mobile phone plus PhoneGuard SET ZONE CONT zzzz Thereafter you walk to the locations you want to include The protection zone expand function is stopped with the command SET ZONE STOP zzz Activating and De activating Protection Zone Function To activate the protection zone monitoring function send the following SMS to your mobile pho
33. telephone network WITHOUT the preceding 0 e yyyyyyy 1234567 for example is the mobile phone number or your telephone number e 7222718 the PhoneGuard PIN e In case of registering a wrong telephone number typing a character than a figure for example the PhoneGuard will respond with an error message PhoneGuard Syntax error in address number When using a landline telephone number as the number through which you will receive messages from the PhoneGuard ensure beforehand that your telephone is able to receive SMS or that your mobile phone network provider offers an SMS to Speech Service which allows you to send an SMS to ordinary telephones The SMS will then be read out to you Depending on the cause for the alarm you will receive a standard text stored in the PhoneGuard Registering Telephone Numbers To be informed by a telephone call send the following messages which communicate your personal telephone numbers to your PhoneGuard SET PHONE1 99xxxyyyyyyy zzzz for the 1 telephone number SET PHONE2 99xxxyyyyyyy zzzz for the 2 telephone number SET PHONE3 99xxxyyyyyyy zzzz for the 3 telephone number IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany g Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de As the PhoneGuard cannot reproduce a spoken text you will hear an alternating high and low pitched tone n the case of an
34. ts or severe shocks If handled roughly in this way the circuit boards inside may become damaged IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 2 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de e Do not apply caustic chemicals solvents or aggressive detergents to the product For cleaning use a soft and dry cloth e Do not apply paint to your PhoneGuard Paint may lead to short circuits in the electronic components e Do not connect any contacts with electric potential to the stripped cable end use zero potential contacts only Only model 108 006 108 010 108 022 e Ensure that the DC resistance of your sensor is max 10 Ohm for closed contact and min 10 MOhm for open contact Only model 108 006 108 010 108 022 e Ensure that the voltage drop across the output switch shouldn t exceed 45V the current flow shouldn t be more than 1A and the power dissipation limit of 1W must be considered also at the same time General zzzz is the PIN Code for the PhoneGuard when supplied it is de activated refer to page 9 to change it e 99 is used in this manual for the international country code which is always necessary to go first before the desired telephone number For the country code of your country refer to the Appendix e The complete communication between the user and the PhoneGuard goes over SMS We recommend storing frequently u
35. ximately 15 30 minutes after the last configuration command was sent to the PhoneGuard it switches to the energy saving mode An alarm event activates it instantaneously Otherwise the PhoneGuard is automatically activated once per minute to check whether an SMS has been sent In connection with a Siemens mobile phone of the 45 series the PhoneGuard is always active These phones do not support energy save mode b IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 20 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Appendix International Country Codes If you do not found your country visit our web page and see the down load area In addition you find information here http www the acr com codes cntrycd htm http kropla com dialcode htm IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 2 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de TERMS OF WARRANTY This warranty applies to the end purchaser of the Product Customer It shall neither exclude nor limit any mandatory statutory rights of the Customer or any of the Customer s rights against the seller dealer of the Product The warranty period s six 6 months from the date on which the first Consumer purchased the Product In case of a subsequent purchase or other change of owner user such warr
36. z b time delay before alarm is send 1 99 sec zzzz PIN EN EN p Contact Alarm Function CAF file ET HE sues Ry activating de activating ZZZZ PIN SET ALARM ON OFF hh mn ZZZZ Alarm Text contact open fttt SMS Text max 128 characters within inverted commas SET OPEN TEXT zzzz PIN lt ttt gt ZZZZ Alarm Text contact close fttt SMS Text max 128 characters within inverted commas SET CLOSE TEXT zzzz PIN lt ttt gt ZZZZ CAF Alarm Configurations fs 1 contact closed 2 contact opened 3 contact SET DETECT s r zzzz opened AND contact closed r delay time between 10 and 120 sec for sending SMS if events 1s occurred zzzz PIN EN mn p lt SN p lt mn IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 6 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intelligent systems de Motion Alarm Function MAF eX Eu PA Ton E activating de activating ZZZZ PIN SET ALARM ON OFF ZZZZ MAF Alarm Text ttt SMS Text max 128 characters within inverted commas SET CLOSE TEXT zzzz PIN lt ttt gt ZZZZ MAF Alarm Configurations fs 2 r delay time between 10 and 120 sec for sending SMS if SET DETECT s r zzzz events is occurred zzzz PIN IS Intelligent Systems GmbH Walter H fer Weg 9 46242 Bottrop Germany 7 Phone 49 0 20 41 37 47 29 0 Fax 1 Email info intelligent systems de www intellig

Download Pdf Manuals

image

Related Search

Related Contents

Herbicida preemergente para el control de dicotiledoneas anuales y  Lezyne LED User Guide  Manuale d`uso - versione ridotta  Unicol SSN flat panel wall mount  Linksys PVC2300 User's Manual  La Crosse Technology WS-7058U User's Manual  Grandio Louver Window  TU TAPES SACHA ET TU TE CASSES !  User Manual  Behringer AM400 Musical Instrument Amplifier User Manual  

Copyright © All rights reserved.
Failed to retrieve file