Professional Woodworker 7611 Use and Care Manual
Contents
1. 11 Do not load fasteners with the airline connected or with trigger Work Contact Element WCE depressed 12 Always fit tool with a fiting or hose coupling on or the tool in such a manner that all compressed air in the tool is discharged at the time the fiting or hose coupling is disconnected 13 Never place hands or any other body parts in the fastener discharge area of the tool 14 Carry the tool by the handle Do not carry by the air hose or with the tigger depressed 118 Do not drive fastener on top of other fasteners 16 Do not operate if any warnings or warning labels are not legible 17 Maintain tools with Check for misalignment or binding of moving parts and for anyother condition that may affect the tool s operation 18 Aways assume the tool contains fasteners Do not point the tool towards yourself or anyone whether it contains fasteners or not 19 Always keep others ata safe distance from the work area 20 Avoid long periods of handling the tool Stop using the tool if you feel pain or stifness in hands or arms 21 Always disconnect the air supply before inspecting the tool 22 Avoid us tool when 23 Clean and check oil air supply hoses and fitings before connecting the tool to air supply Replace any damaged or wom hoses or fittings OPERATING THE TOOL CAUTION Keep fingers away from trigger when not driving fasteners to avoid accide2. e ime mee i E uH Bep RE Tem e ir sn x a m marine Ss 5 p 47 tw 3 E oe e rr nemi 5 a Ear ons ps v 2 w m pr a a n ms a n ome fa s use CINE EST gt 3 gt i a E a Please carefully read and save these instructions before attempting to assemble maintain install operate this product Observe all safety information to protect yourself and others Failure to observe the instructions may result in property damage and or personal injury Please keep instructions for future reference Important Operating Instruction 18 GAUGE 1 1 4 INCH BRAD NAILER Model 7552 CALIFORNIA PROPOSITION 65 WARNING You can create dust when you cut sand drill grind materials such as wood paint metal concrete cement or other masonry This dust often contains chemicals known to cause cancer birth defects or other reproductive harm Wear protective gear WARNING This product or its power cord may contain chemicals Including lead known to the Sta
3. Do not use pressure which could exceed 110psi 5 Keep the generator away from all flammable liquids and gases 6 Stayalert while operating the tool Do notuse while under the influence of drugs or alcohol For warranty purchases plea keep your dated proof of purchase ie or attach to the manual for safekeeping For customer service ca 1 800 348 5004 or ema feedback natiiools com 8807552 0700 7 Do not overreach when Using this tool Keep proper footing and balance times 8 Check the tool carefully before each use Do not use if problems are found 9 Do modify or tamper with the tool in any way 10 Disconnect the 1001 from the air compressor and power source before making any adjustments changing the accessories or storing the tool 11 Do not load fasteners with the airline connected or with trigger or Work Contact Element WCE depressed 12 Always fit tool with a fiting or hose coupling on or near the tool in such a way that all compressed air in the tool is discharged atthe time the fiting or hose coupling is disconnected 13 Never place hands or any other body parts in the fastener discharge area of the tool 14 Carry the tool by the handle Do not carry bythe air hose or with the tigger depressed 18 Do not drive fastener on top of other fasteners 16 Do not operate if any warnings or warning labels
4. are not legible 17 Maintain tools with care Check for misalignment or binding of moving parts and for anyother condition that may affect the tool s operation 18 Aways assume the tool contains fasteners Do not Point the tool towards yourself or anyone whether it contains fasteners or not 19 Always keep others ata safe distance from the work area 20 Avoid long periods of handling the tool Stop using the tool if you feel pain or stifness in hands or arms 21 Always disconnect the air supply before inspecting performing maintenance on the tool 22 Avoid using the tool when the magazine is empty Accelerated wear on the tool mayoceur 23 Clean check and oil Supply hoses and fittings before connecting the too to air supply Replace any damaged or wom hoses or fittings OPERATING THE NAILER CAUTION Keep fingers away from trigger when not driving fasteners to avoid accidental firing The air compressor must be able to maintain minimum of 60psi when the tool is being used An oiler and a filter can help the performance of the tool Use 3 8 in 10mm air hoses with maxworking pressure 110psi for 50 ft length or greater For better performance install a quick plug with an inside diameter of 5 16 in 8mm on the tool and quick coupler on the air hose Use a pressure regulator on the compressor with an operating pressure of 60 110psi Apressu
5. the tool so the air inlet is facing up Place 4 5 drops of 30W non detergent oll into alr inlet Do not use detergent oil additives or air tool oil too oli contains solvents which will damage the tool s internal components 3 After adding oil run tool briefly Clean off any excess oil from the exhaust CHECKING THE WORK CONTACT ELEMENT wcE NOTICE Check the operation of the WCE trip mechanism before each use The WCE must move freely without binding through its travel distance The WCE spring must return the WCEto its fully extended position after being depressed Do not operate the tool if the WCE trip mechanism is not operating properly 1 Disconnect the air supply from the tool 2 Remove all fasteners from the magazine 3 Make sure the trigger and WCE move freely up and down without sticking or binding 4 Reconnect air supply to the tool 5 Depress the WCE against the work surface without pulling the trigger The tool must not operate Do not use the tool ifit operates without pulling the trigger Personal injury may result 6 Remove the tool from the work surface The WCE must return to its original down position Pull the trigger The tool must not operate Do not use the tool ifit operates Personal injury may result 7 Depress the WCE against work surface Pull the trigger The tool must operate ADJUSTING THE FASTENER PENETRATION 2 Connect the
6. 8 5004 Teodbacktinatitools com 1 300 348 5004 18 GAUGE 1 1 4 INCH BRAD NAILER Model 7552 com 8907552 07 10 Call 1 800 348 5004 for assistance or replacement parts Pose provido kloning forma aes Moi number Port deerpfen ed rumbere shown in perat Nort Aerian Tod artis Serial number if any Huntington IN 46750 we Tar mo Tam mo nee Tay v T erem T m s ae 1 x we s d m RN 6 I 3 Luc menn ma a E am ww 1 cR E 5 3 s mi s ss p pep fe ee s maman omma 5 SE Sp per eee dr REM masa MIT ep s w mem fi r o pepe Hd EE owe wi mw fi n ms fi x ome orean a o jije x a mes x eee fa e masa ps 3 sm s s os ee eese nati s si aie fre ae mms Teedbacktinatitools com 1 300 348 5004
7. MPLETELY AND CAREFULLY ine tool to explode which will handling BEFORE OPERATING THIS cause death or serious NARROW CROWNSTAPLER personal injury Important Any failures made in following 4 Use clean dry regulated the safety regulations and compressed air at 60 100psi obsened to avoid injuries and Instructions may esuitinan Do use pressure which electric ahook fire andior could exceed 110psi damage Please read the complete operating manual with Serious Injury 5 Keep the generator away a e ees from all flammable liquids and jases is available atali times Ifyou give gt the equipment 6 Stay alert while operating person give them these the tool Do not use while operating instructions as well We under the influence of drugs or accept no liability for damage or alcohol For warranty purchas keep your dated proof of purchase File attach to the manual for safekeeping plea For customer service cat 1 800 348 5004 or emai feedbackGinatitosls com d 8809387 0700 7 Do not overreach when using this tool Keep proper footing and balance at times 8 Check the tool carefully before each use Do not use if problems are found 9 Do notattemptto modify or tamper with the tool in any way 10 Disconnect the too from the air compressor and power source before making any adjustments changing the accessories or storing the tool
8. Please carefully read and save these instructions before attempting to assemble maintain install or oporate this product Observe all safety information to protect yourself and others Failure to observe the instructions may result in property damage andlor personal injury Please keep instructions for future reference 18 GAUGE 1 4 INCH NARROW CROWN STAPLER Model 9387 7611 CALIFORNIA PROPOSITION 65 accidents whicharisedueto SAFETY INSTRUCTIONS non observance of these WARNING You can create dust ingtricions and the safety 1 Read and understand tool when you cut sand drill or grind 87000079 ang h materials such as wood paint labels and the manual Failure male menue to follow warnings dangers other masonry This dust often SPECIFICATIONS piel T Toe Contains chemicals known to Operation Pressure 60 100PSI cause cancer birth defects or Magazine Capacity 100 pieces other reproductive harm Wear Fastener Length 1 2 1 1 4 2 Use safety equipment that conforms to local regulations PRAE Such as safety glasses with WARNING This product or its side shields and ear power cord may contain x protection chemicals including lead CAUTION known to the State of California 3 Only use compressed air to cause cancer and birth FOR YOUR OWN SAFETYREAD Use of anyair other than defects or other reproductive INSTRUCTION MANUAL compressed air may cause harm Wash hands after CO
9. air supply and test for penetration by driving fasteners into a sample piece of wood ifthe fasteners do not achieve the desired penetration adjust the air pressure to higher setting Until the desired penetration is achieved Do not exceed 110psi at the too or durability of the tool will be reduced CLEARING A JAM FROM THE TOOL WARNING Disconnect the air supply from the tool first Fastener jammed in fastener discharge 1 Disconnect ool from the air hose 2 Open the nozze part grab jammed fastener with pliers remove Fastener jammed inside magazine 1 Disconnect tool from air hose 2 Pull back the magazine cover 3 Open the nozze part and remove jammed fastener 4 Push the magazine cover forward until the latch catches ASSEMBLY PROCEDURE FOR SEALS WARNING Disconnect the air Supply from the tool When repairing a tool the internal parts mustbe cleaned and lubricated Parker O ube or equivalent must be used on all O rings Each O ring must be coated with O lube before assembling Asmall amount Tesdbsck natitools com 1 300 348 5004 must be used moving surfaces and pivots Afer reassembling a few drops of 30W non detergent oil or equivalent must be added through the airline before testing Rapid Fire Operation The tool can also be operated byholding the trigger depressed and pushing contact rip against the work le
10. ce Afastener will be driven ach time the contact trip is pushed against the work piece This operating procedure provides rapid fire fastener driving Never operate tool unless contact trip is in contact with the work piece Teodback natitols com 1 300 348 5004 Troubleshooting Guide Symptom Possible Cause s Corrective Action Loose screws screws Air leak naar top of too in trigger Worn or damaged O rings or seais Install overhaul kit Inadequate ar supply Tool oes nothing or operates Check sluggishiy Worn or damaged O rings or seais Worn or damaged O rings or bumper Install overhaul kit Install overhaul kit Incorrect fastorors tastenors of corroct sizo Damaged fasteners with undamaged fastenors jams frequen epe Magazne or nose screw Devers worm or damaged screws Install drwor maintenance kit TesdbsckGnatitools com 1 300 348 5004 Limited Manufacturer Warranty North American Tool NAT Industries makes every effort to ensure that this product meets high quality and durability standards NAT warrants to the original retail consumer a 1 year limited warranty from date the product was purchased at retail and each products free from defects in materials Warranty does not apply to defects due directly or indirectly to
11. eturn the WCE to its fully extended position after being depressed Do not operate the tool if the WCE trip mechanism is not operating properly 1 Disconnect the air supply from the tool 2 Remove all fasteners from the magazine 3 Make sure the trigger and Work Contact Element WCE move freely up and down without sticking or binding 4 Reconnect air supply to the too 5 Depress the WCE against the work surface without pulling the tigger The tool must not operate Do notuse the tool operates without pulling the trigger Personal injurymay result 6 Remove the tool from the work surface The WCE must retum to its original down position Pull the trigger The tool must not operate Do not the tool ifit operates ersonal injury may result 7 Depress the WCE against work surface Pull the trigger The tool must operate ADJUSTING THE FASTENER PENETRATION 1 Regulate the air pressure to 60psi at he tool 2 Connect the air supply and test for penetration by driving fasteners into a sample piece of wood ifthe fasteners do not achieve the desired penetration adjust the air pressure to higher setting Until the desired penetration is achieved Do not exceed 110psi or the durability of the too will be reduced CLEARING A JAM FROM THE TOOL WARNING Disconnect the air Supply from the tool first Fastener jammed in fastener discharge are 1 Disconnect too from the a
12. ir hose 2 Open the nozze part grab jammed fastener with pliers remove Fastener jam inside magazine 1 Disconnect too from the air hose 2 Pull back the magazine cover 3 Open the nozze part and remove jammed fastener 4 Push the magazine cover forward until the latch catches ASSEMBLY PROCEDURE FOR SEALS WARNING Disconnect the air supply from the tool before performing maintenance When repairing a tool the internal parts mustbe cleaned and lubricated Parker O lube Tesdback natitools com 3 1 300 348 5004 or equivalent must be used on all O rings Each O ring must be coated with O lube before assembling Asmall amount of oil must be used on all moving surfaces and pivots After reassembling a few drops of 30W non detergent oil orequivalent must be added Rapid Fire Operation The tool can also be operated byholding the trigger depressed and pushing the contact trip against the work plece Afastener will be driven each time the contact trip is pushed against the work piece This operating procedure provides rapid fire fastener driving Never operate tool unless contact trip is in contact with the work piece Tesdback atitools com 1 300 348 5004 Troubleshooting Guide Symptom Possible Cause s Air leak near top of tool or in tigger area Worn or damaged O rings or seais install overhaul kit Inadequate air suppl
13. misuse abuse negligence or accidents repairs or alterations or a lack of maintenance NAT shall in no event be liable for death injuries to persons or property or for incidental special or consequential damages arising the use of our products To receive service under warranty the original manufacturer part must be retumed for examination by an authorized service center Shipping and handling charges may apply Ifa defect is found NAT will either repair or replace the product at its discretion DO NOT RETURN TO STORE For Customer Service Email feedback natitools com or Call 1 800 348 5004 Teodbacktinatitools com 1 300 348 5004 Qs 18 GAUGE 3 8 INCH NARROW CROWN STAPLER Model 9387 x 5 2 Y a sy E T pm 4 8909387 07 10 Call 1 800 348 5004 for assistance or replacement parts Pose provido tho ing forma any Moi number Part od umber shown pars st tert Arena To artis Serial number if any Huntington IN 46750 we Tan mo am meet v cemere tna s s ss mesa 3 mma 181 za mem Te Bep Er 5 i sL 7 Bep p
14. ntal firing RECOMMENDED HOOKUP The air compressor must be able to maintain a minimum of 60psi when the tool is being used oiler and a filer can help aid the performance of the tool Use 3 8 in 10mm air hoses with a maxworking pressure of 110psi for 50 ft run or longer For better performance install a quick plug with an inside diameter of 5 16 in 8mm on the tool and quick coupler on the air hose Use a pressure regulator on the compressor with operating pressure of 60 110psi Apressure regulator is required to control operating pressure of the tool between 60 and 100psi LOADING THE TOOL WARNING Disconnect tool from air hose before loading 1 Depress the magazine latch Pull back on the magazine cover 2 Inserta stick of fasteners into the magazine Make sure the fasteners are loaded with the points downward Make sure the fasteners are not dirty or damaged 3 Push the magazine cover forward until the latch catches LUBRICATION The tool requires lubrication before using the tool for the first time and before each use Ian inline oiler is used manual lubrication through air Tesdbsck natitools com 1 300 348 5004 inletis not required on a daily basis NOTICE Fallure to lubricate the tool properly will dramatically shorten the of the tool and void the warranty 1 Disconnectthe air supply from the tool to add lubricant 2 Tum
15. re regulator is required to control the operating pressure ofthe tool between 60 and 100psi LOADING THE TOOL WARNING Disconnect tool from air hose before loading 1 Depress the magazine latch Pull back on the magazine cover 2 Inserta stick of fasteners into the magazine Make sure the fasteners are loaded with the points downward Make sure the fasteners are not dirty or damaged 3 Push the magazine cover forward until the latch catches LUBRICATION The tool requires lubrication Tesdbsck natitools com 1 300 348 5004 before using the tool for the first time and before each use inline oller is used manual lubrication through air inlet is not required on a daily basis NOTICE Failure to lubricate the tool properly will dramatically shorten the Ife of the tool and vold the warranty 1 Disconnect the air supply from the tool to add lubricant 2 Tum the tool so the air inlet is facing up Place 4 5 drops of 30W non detergent oil into air Inlet Do not use detergent oll cil additives or air tool oil Air too oll contains solvents which will damage the tool s internal components 3 After adding run tool briefly Clean off any excess oll from the cap exhaust CHECKING THE WORK CONTACT ELEMENT WCE NOTICE Check the operation of the WCE trip mechanism before each use The WCE must move freely without binding through its travel distance The WCE spring must r
16. te of California to cause cancer and birth defects or other reproductive harm Wash hands after handling Important When using equipment a few safety precautions must be observed to avoid Injuries and damage Please read the complete operating manual with due care Keep this manual in a safe place so that information is available times If you give the equipmentto any other person give them these operating instructions as well We accept no liability for damage or accidents which arise due to non observance of these instructions and the safety information herein SPECIFICATIONS Operation Pressure 60 100PSI Magazine Capacity 100 Fastener Length 3 8 1 1 4 inch Uses types of 18 brad nails COMPLETELY AND CAREFULLY BEFORE OPERATING THIS BRAD NAILER Any failures made in following the safety regulations and Instructions may result in an electric shock fire andlor rious injury SAFETY INSTRUCTIONS 1 Read and understand tool labels and the manual Failure to follow warnings dangers precautions could result in death or Serious injury 2 Use safety equipment such eye protection ear protection gloves hat when applicable 3 Only use compressed air Use of any air source other than compressed air may cause the tool to explode which will cause death or serious personal injury 4 Use clean dry regulated compressed air at 60 100psi
17. y Check serows does nothing or operates sluggishly Worn or damaged O rings or seals Install overhaul kit Loose screws Tighten screws Damaged fasteners install overhaul kit Replace with undamaged fastonors Tool jams frequently pem screws Magazine is dy Coan screws Driver is or damaged Install driver maintenance kit TesdbsckGnatitools com 1 300 348 5004 Limited Manufacturer Warranty North American Tool NAT Industries makes every effort to ensure that this product meets high quality and durability standards NAT warrants to the original retail consumer a 1 year limited warranty from date the product was purchased at retail and each product is free from defects in materials Warranty does not apply to defects due directly or indirectly to misuse abuse negligence or accidents repairs or alterations or a lack of maintenance NAT shall in no event be liable for death injuries to persons or property or for incidental special or consequential damages arising from the use of our products To receive service under warranty the original manufacturer must be retumed for examination by an authorized service center Shipping and handling charges may apply defect is found NAT will either repair or replace the product at its discretion DO NOT RETURN TO STORE For Customer Service Email feedback natitools com or Call 1 800 34
Download Pdf Manuals
Related Search