Wilton 10010 Use and Care Manual
Contents
1. Operating Instructions amp Service Parts Manual All Terrain Vise 10010 A Record purchase information for quick reference Stock No 10010 Serial No Purchased from Date purchased WILTON Manual No M 10010 427 New Sanford Road Rev A 11 2013 LaVergne Tennessee 37086 Ph 800 274 6848 Copyright O 2013 www wWiltontools com Warranty and Service JET Wilton and Powermatic warrants every product they sell against manufacturers defects If one of our tools needs service or repair please contact Technical Service by calling 1 800 274 6846 8AM to 5PM CST Monday through Friday Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET Wilton or Powermatic branded websites e JET Wilton and Powermatic products carry a limited warranty which varies in duration based upon the product See chart below e Accessories carry a limited warranty of one year from the date of receipt e Consumable items are defined as expendable parts or accessories expected to become inoperable within a reasonable amount of use and are covered by a 90 day limited warranty against manufacturer s defects Who is Covered This warranty covers only the initial purchaser of the product from the date of delivery What is Covered This warranty covers any defects in workmanship or materials subject to the limitations stated below This warranty2. 21 mammaa ATV 2022420000 SPACON eee NN Ne ee oma dotmt vetsset ess L do JHM610 22 Socket Head Cap Screw MOX Isere ne PP ee ATV 22 eee Bench Mount Receiver arrei E seeueceeeceeceueceeeceeeeeeseesueseeenaes Some parts are shown for reference only and may not be available as replacement parts WILLEN 427 New Sanford Road LaVergne Tennessee 37086 Phone 800 274 6848 www wiltontools com
3. vise handle is locked and hitch pin is properly engaged before driving vehicle Read and understand all warnings posted on the vise and in this manual Failure to comply with all of these warnings may cause serious injury Do not use this vise for other than its intended use Replace warning labels if they become obscured or removed Always wear ANSI approved safety glasses or face shield when using striking or power tools with this vise Everyday eyeglasses only have impact resistant lenses they are not safety glasses Wear hearing protection when needed Do not wear loose clothing or jewelry Confine long hair Keep clothing hair and gloves away from moving parts Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paint Crystalline silica from bricks cement and other masonry products Arsenic and chromium from chemically treated lumber Your risk of exposure varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as face or dust masks that are specifically designed to filter out microscopic particles Always inspect vise before use Check for misalignment of moving parts binding of moving parts breakage of parts mounting an
4. PETIA TT cee hte Po hat te tv e auma PR Oy anoa 18 kg 39 68 Ib DIMENSIONS uma massat ua usa a seus cee s nn aa n kaavaan 489 x 150 x 185 mm 19 1 4 x 6 x 7 1 4 in Ema matenalS ESS RS SR en ne een ean eden steel and ductile iron PAIE INIST eee dan M Oe ee ee powder coat enamel The specifications in this manual were current at time of publication but because of our policy of continuous improvement Wilton reserves the right to change specifications at any time and without prior notice without incurring obligations Setup and assembly Read and understand all Instructions and warnings in this manual before attempting installation or operation of hitch vise Failure to comply may cause serious injury Shipping contents Vise Hitch pin with cotter pin Bench mount receiver Instructions and parts manual Warranty card i A A A A Remove contents from shipping carton and check for shipping damage or missing parts If either of these is discovered contact your dealer or Walter Meier Manufacturing Inc at the phone number on the cover Installing to hitch Refer to Figure 2 The All Terrain Vise is designed to be inserted into a 2 inch square hitch receiver 1 Slide vise tube into receiver If there is too much play within the receiver remove the vise and rotate any of four screws A on the vise tube with a 5 16 hex key Reinstall and test for fit making further adjustments as needed Align hole in vise tube wit
5. RCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU JET WILTON AND POWERMATIC SHALL IN NO EVENT BE LIABLE FOR DEATH INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL CONTINGENT SPECIAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU JET Wilton and Powermatic sell through distributors only The specifications listed in JET Wilton and Powermatic printed materials and on official JET Wilton and Powermatic branded websites are given as general information and are not binding JET Wilton and Powermatic reserve the right to effect at any time without prior notice those alterations to parts fittings and accessory equipment which they may deem necessary for any reason whatsoever JET branded products are not sold in Canada by Walter Meier Manufacturing Americas Product Listing with Warranty Period 90 Days Parts Consumable items Light Duty Air Tools 1 Year Motors Machine Accessories Heavy Duty Air Tools Pro Duty Air Tools 2 Year Metalworking Machinery Electric Hoists Electric Hoist Accessories 5 Year Woodworking Machinery Limited Lifetime Wilton branded products JET Parallel clamps Manual Hoists Manual Hoist Access
6. d any other conditions that may affect the tool s operation If damage is found repair the vise immediately or replace it Have tool serviced only by qualified personnel using authorized replacement parts 3 19 Provide for adequate space surrounding work area and sufficient lighting 20 Do not use this tool while tired or under the influence of drugs alcohol or medication 21 Keep bystanders especially children away from the area while using the vise 22 Give your work undivided attention Looking around carrying on a conversation and horse play are careless acts that can result in serious injury 23 Maintain a balanced stance at all times Do not overreach while performing the work About this vise The WILTON All Terrain Vise has been designed and constructed to provide consistent long term operation if used in accordance with instructions as set forth in this document The body is formed of high strength ductile cast iron The leadscrew is precision ground carbon steel with acme threads The tube has adjusting screws top and side for eliminating play inside the hitch receiver The handle can be repositioned without moving the jaws About this manual This manual covers operation and maintenance procedures for a WILTON All Terrain Vise It contains instructions on installation safety precautions general operating procedures maintenance instructions and parts breakdown The instructions and warnings presented in th
7. does not cover failures due directly or indirectly to misuse abuse negligence or accidents normal wear and tear improper repair alterations or lack of maintenance Warranty Limitations Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year Warranty Please contact Technical Service at 1 800 274 6846 for further clarification How to Get Technical Support Please contact Technical Service by calling 1 800 274 6846 Please note that you will be asked to provide proof of initial purchase when calling If a product requires further inspection the Technical Service representative will explain and assist with any additional action needed JET Wilton and Powermatic have Authorized Service Centers located throughout the United States For the name of an Authorized Service Center in your area call 1 800 274 6846 or use the Service Center Locator on the JET Wilton or Powermatic website More Information JET Wilton and Powermatic are consistently adding new products For complete up to date product information check with your local distributor or visit the JET Wilton or Powermatic website How State Law Applies This warranty gives you specific legal rights subject to applicable state law Limitations on This Warranty JET WILTON AND POWERMATIC LIMIT ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT EXCEPT AS STATED HEREIN ANY IMPLIED WARRANTIES OF ME
8. h hole in hitch receiver Insert hitch pin B completely through receiver and vise tube 4 Install cotter pin C through hole in hitch pin AWARNING Cotter pin must be properly secured in hitch pin before operating vise or moving vehicle to which vise is mounted Figure 2 Installing to bench table Bench or table must be capable of supporting combined weight of vise workpiece and applied forces If additional strength is needed mount supporting boards beneath the table Refer to Figures 3 and 4 1 Position vise on bench The rear or static jaw should just overhang the bench to prevent obstruction when inserting long work pieces 2 Place bench receiver over vise tube and mark hole positions on bench Figure 3 identifies hole dimensions Drill holes of appropriate diameter in table 3 Mount bench receiver to bench using fasteners of Suitable grade length and diameter The hole in the side of the receiver should be at the end farthest from the vise 4 Slide vise tube into bench receiver If there is too much play within the receiver rotate any of the four adjustment screws on the tube A Figure 2 5 Install hitch pin through holes of tube and receiver Figure 4 6 Install cotter pin into hitch pin hole 13 x4 Figure 4 Adjustments and Operation Before use inspect the vise for cracks misalignment binding or any other problems that may compromise Its safe use Hand
9. is manual cannot of course cover all possible situations or conditions in which a vise may be used The operator is expected to take appropriate precautions and exercise common sense As with any tool operation safety of the operator and bystanders should be first priority If there are questions or comments please contact your local supplier or Wilton Wilton can also be reached at our web site www wiltontools com Retain this manual for future reference If the tool transfers ownership the manual should accompany it AWARNING Read and understand the entire contents of this manual before installing or using the All Terrain Vise Failure to comply may cause serious injury Specifications IOC Clic IIKENNE MININ JANIH III EASE WILTON All Terrain Vise SORA MO EE aio omata a sto omiaan K ss tasasi A A 10010 FREQUINEG MITCH FCO nn sonne ne een tien des ses nn ae den 2 in square JAM NICE nn dec he beat eue teen A etc ce nee Sn dis 150 mm 6 in Maximu JaW OPENIN Leva taaemmas assa sa N a nan ee ennui 145 mm 5 3 4 in JAW INSSI MANOMESS aessa iiaiai RR none aa a ne none n ee cle 45 56 HRC Pipe capacity samson nn tanten en 3 4 3 in or 1 2 3 in with one jaw insert removed ClAMPING TOKO ER RE EE RE 1 ton LO AES DIE Sade MER CM AS avaa eat ASSEN k it PETE EEDE 127 mm 5 in Jaw travel per one rotation of handle ee ccecssseeeeceseeeceeeseeecceuseeeceauseeessaueeeseseeecsaneeeessaseees 4 mm 0 15 in LN
10. le adjustment Refer to Figure 5 The handle hub is spring loaded and allows the handle to be repositioned without moving the jaws After securing the workpiece in the jaws grasp handle hub and pull out Rotate handle hub to desired position then release Rotate to position and release Figure 5 Replacement Parts To operate the hitch vise 1 Turn screw handle counterclockwise to open jaws Do not try to force jaws apart farther than the rated capacity jaw opening 2 Choose the straight jaws or pipe jaws Insert workpiece and turn handle clockwise to close jaws 3 Tighten enough that workpiece can no longer be shifted within the jaws Do not overtighten as this may damage workpiece and or jaws Maintenance Inspection Before use inspect vise for misalignment binding or cracked damaged parts or any other condition that may affect safe operation Repair or replace a damaged vise Cleaning After use wipe external surfaces of the vise with a clean rag Apply a light coat of machine oil to exposed metal areas Lubrication The leadscrew is permanently lubricated and enclosed and should not require attention Lubricate other moving parts of the vise with machine oil Jaw insert replacement Use a 5mm hex key to remove two screws on the jaw insert Securely tighten the new jaw insert to the vise using the same screws NOTE If replacing jaw inserts replace both as a set To order parts or reach ou
11. ories Shop Tools Warehouse amp Dock products Hand Tools NOTE JET Wilton and Powermatic are divisions of Walter Meier Manufacturing Americas References in this document to JET Wilton and or Powermatic also apply to Walter Meier Manufacturing Americas or any of its successors in interest to the JET Wilton and or Powermatic brands Read and understand the entire owner s manual before attempting installation or operation 11 12 13 14 19 16 17 18 Warnings Keep hands clear of jaws Make sure vise is properly secured to hitch receiver If using accessory bench receiver vise must be properly secured within receiver and receiver bolted to bench with appropriate fasteners not included Do not use the vise as a step it may cause an individual to slip and fall This caution is also inscribed in the anvil of the vise see Figure 1 Keep ground or floor around the vise uncluttered and free of scrap material oil and grease Wear non slip footwear Do not place combustible materials or pressurized containers in vise Do not force the tool Do not use a hammer against the handle or use additional leverage such as cheater bars or pipe extensions to tighten the screw handle For heavier jobs use a larger vise Vehicle safety brake must be engaged before operating vise Do not drive vehicle with material in the vise Use caution when backing a vehicle with the vise installed Figure 1 Make sure
12. r service department call 1 800 274 6848 Monday through Friday 8AM to 5PM CST Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately WILTON All Terrain Vise 10010 Exploded View N A yy SUV WILTON All Terrain Vise 10010 Parts List Index No Part No Description Size Qty ARE ATV HA Handle Assembly index 1 5 ccseeseeseeseenseesseeseeteeeenseesaeeees l cRRan AV VOI maamassa AD cele tee ee A amm am Kia TR cern E du ae D eee RIV O2 muse PA AIO RE Dion ATV 08 mms Socket Mead Cap SCT ne Marne ones Re ATV Om Wache acin nt tan O11 x O20x 2mm din ATV 05 cms S DIO RE a he Ree tain VOX 22 MM SET ATV 09 nus SEF 01 WV gaits eesti isle a dts Re ute hea ated cheat tends G 10e ATY Os SDINAIS OA ane Managers sr Reine he ATV samastaa Lead S CROW io ie yt taitoa alankojen sia aja rm Rae da IZ am dde aa PIOAUNG sd AW BOOY ANS as deci aed oe KE MOTT S ESSI K EE HOS SS Na loue ANS Jaw Insen SOU OT 2 6 L x 1 2 W x 7 87H A aan TS 1503031 Socket Head Cap Screw MOX 12 32 se NG eee eres ee ie SIAUONA N JAWBOAY iisimmin sameaa een eee Rien ee OS ee ATV IO mme PLO NKP a E E E T OLOT eee eee i ator nr ren AIN IT eaaaaanaa COOPIN aoa aa fue aoe A Diana tenet ones 1G ie ANT ACIUSUMENL SCIE NN ee se Ode AIN ROPI a ACTA eaaa Ed CR ATV Ie S 91 96 eNO teeta ee see a en nt ne
Download Pdf Manuals
Related Search