Mirage HDMirage16S Use and Care Manual
Contents
1. Page 10 Assembly Step 9 Reflector handle Fitting reflector handle Using the pre fitted R clip and pin secure the reflector handle to the bracket as shown Reflector Handle Page 11 Assembly Step 10 5 16 Bolt G 5 16 Washer F Top Panel Side Panels 1 4 Dome Head 1 4 Nut B Bolt A Loosely screw parasol side panels together using 12 of the 1 4 Dome Head Bolts Ref A and 1 4 Nuts Ref B overlapping as shown below Fix the top panel to the top of the assembled side panels using 6 of the 1 4 Dome Head Bolts Ref A and 1 4 Nuts Ref B and then fully tighten all bolts Side Panels Top Panel ss Fit reflector to lantern as shown using 3 of the 5 16 bolts Ref G and washers Ref F Page 12 For all appliances e The heater when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 or the Canadian Electrical Code CSA C22 1 e Certain materials or items when stored under the heater will be subjected to radiant heat and could be seriously damaged e Inspect the visible portion of the hose before each use of the appliance Hose inside cylinder pole housing should be checked annually and a leak test should be performed when re assembled Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid bu2. Dome Head Bolt Bolt i Fixings are shown at actual size 5 16 Bolt Lu 3 1 4 Spring e Check the contents of the box and make sure you have all the parts and fittings listed If not contact the factory by email info uigroup ie or the Helpline 678 534 2876 e When you are ready to start make sure that you have the right tools at hand plenty of space and a clean dry area for assembly Before You Start Assembly e Please lay out all nuts and bolts and check lengths before assembly It is recommended that the carton is cut open and spread out on the floor and used as a protective surface during assembly Refer to the assembly diagrams as necessary Important while every precaution has been made in the manufacture of this product care must be taken during assembly in case sharp edges are present Page 2 Assembly Step 1 p el 4 SHARMA A 4 am Base Cylinder Chamber 1 4 Supports A B C Hex Bolt C Fix the cylinder chamber supports A B C to corresponding location on the base with 6 of the 1 4 hex bolts Ref C Finger tighten only Cylinder chamber supports Base Page 3 Assembly Step 2 Lower 1 4 Nut B 1 4 Support Pole Hex Bolt C Fix lower support pole to cylinder chamber supports as shown using 6 of the 1 4 hex bolts Ref C and 6 of the 1 4 nuts Ref B Finger tighten only Page 4 Assembly Step 3 Cylinder 1 4 Dome 1 4
3. Nut Chamber Wall Head Bolt A B Fit the cylinder chamber wall to the cylinder chamber supports using 6 of the 1 4 dome head bolts Ref A and 6 of the 1 4 nuts Ref B Finger tighten only 000055 Page 5 Assembly Step 4 Cylinder Chamber door Hang door on hinges Ensure correct alignment and tighten all bolts securely Cylinder Chamber door Hinges Page 6 Assembly Step 5 Cylinder 1 4 Dome Head 1 4 Nut Chamber Top Bolt A B Fit cylinder chamber top onto cylinder chamber support legs using 3 of the 1 4 dome head bolts Ref A and 3 of the 1 4 nuts Ref B Cylinder Chamber Top 000000068686 E EE E i T E E E 106000000066 060822000001 060000086866 9eesmeeseees Page 7 Assembly Step 6 O 1 4 Hex Bolt C 1 4 Washer D 1 4 Spring Washer E Fit upper support pole to lower support pole using 3 of the 1 4 hex bolts Ref C and spring washers Ref E and washers Ref D 1 4 Washer D 1 4 Spring Washer E 1 4 Hex Bolt C Page 8 Assembly Step 7 nl 0 O IT 1 4 Hex Bolt C 1 4 Washer D 1 4 Spring Battory Washer E Feed the lantern hose down the support pole and secure lantern to support pole using 4 of the 1 4 Hex Bolts Ref C and spring washers Ref E and washers Ref D Lantern 1 4 Washer D O N 1 4 Spring Spark
4. e This appliance is for OUTDOOR USE ONLY and should be placed in a well ventilated area e A well ventilated area must have a minimum of 30 of its surface area open Surface area is defined as the total surface of the walls surface e The sides of the appliance should NEVER be closer than 40 inches 1m from any combustible surface e Keep this appliance away from any flammable materials e Important Make sure the gas bottle is placed level within the base Should you need to change the gas bottle confirm the gas supply is turned off at the regulator or bottle cylinder valve and there are no sources of ignition cigarettes open flame sparks etc near before proceeding e Inspect the gas hose to ensure it is free from any twisting or tension The hose should hang freely with no bends folds or kinks that could obstruct free flow of gas Always inspect the hose for cuts cracks or excessive wear before use If the hose is damaged it must be replaced with hose suitable for use with LPG and meet the national standards for the country of use Connecting to the cylinder e Confirm all control knobs are in the off position Connect the regulator to the gas bottle according to your regulator and bottle dealers instructions Page 14 Use Instructions Before proceeding make sure you understand the warnings section of this manual Lighting instructions Fit battery to sparker e Turn on gas supply at cylinder e Push dial i
5. be a Constructed and marked in accordance with the specifications for LP gas cylinders of the U S Department of Transportation DOT or the Standard for cylinders Spheres and Tubes for Transportation of Dangerous Goods and Commission CAN CSA B339 as applicable b Provided with a listed overfilling prevention device and c Provided with a cylinder connection device compatible with the connection for the appliance d 20LB 9kg cylinder LPG capacity 4 7 gallons 17 8 litres Cylinder Dimensions Height 17 75 inches 451mm and width 12 25 inches 811mm e The LP gas cylinder used must include a collar to protect the cylinder valve A cylinder must be stored outdoors in a well ventilated area out of reach of children A disconnected cylinder must have dust caps tightly installed and must not be stored in a building garage or any enclosed area The pressure regulator and hose must be used and any replacement pressure regulator or hose must be those as specified by the manufacturer Do not store spare LP gas cylinder under or near this appliance Never fill the cylinder beyond 80 percent full and for appliances designed to use a CGA No 791 Connection Place the dust cap on the cylinder valve outlet whenever the cylinder is not in use Only install the type of dust cap on the cylinder valve that is provided with the cylinder valve Other types of caps or plugs may result in leakage of propane Page 13 Leak Testing To be pe
6. e Any modification of this appliance may be dangerous DO NOT use heater where the reflector is within 40 inches 1m of any flammable structure or surface e NEVER operate the heater with the top half covered burner head reflector etc e DO NOT leave this product unattended when in use e Always keep the cylinder level and vertical when positioning inside the base ONLY use this appliance on a flat LEVEL non flammable surface or ground e Positioning ensure the unit is a minimum of 40 inches 1m from flammable items or structure from all sides and above e Always leak test the unit before use annually or after storage when parts are replaced serviced or if the gas cylinder is removed or replaced e When storing the appliance or gas cylinder ensure they are away from flammable materials or liquids e Regularly check that the regulator seal and hose is fitted and that it is in good condition Replace parts if necessary e Always follow the care and maintenance instructions regularly maintain your appliance e Always replace worn parts do not use the appliance if a leak wear or damage is found DO NOT store or cover the appliance until fully cooled e Always shut off the valve at the gas cylinder or the regulator before moving the appliance In the event of high winds particular attention must be taken Store the unit away or ensure it is at a safe distance from other items in the event that the unit is blown over e O
7. Assembly amp User Instructions Mirage 38 200Btu Heat Focusing Patio Heater These instructions are for your safety Please read them thoroughly before use and retain them for future reference DANGER If you smell gas 1 Shut off gas to the appliance 2 Extinguish any open flame 3 If odor continues keep away from the appliance and immediately call your gas supplier or fire department WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance An LP cylinder not connected for use shall not be stored in the vicinity of any other appliance WARNING For Outdoor Use Only WARNING Improper installation adjustment alteration service or maintenance can Cause injury or property damage Read the installation operating and maintenance instructions thoroughly before installing or servicing this equipment Patent No US 8 176 910132 We provide a Customer Support Service If you have any queries please contact us on info uigroup ie or tel 678 534 2876 or visit our website www uigroup ie Parts Supplied E J l i Page 1 Cylinder Chamber Supports Cylinder Chamber Door Cylinder Chamber Wall Cylinder Chamber Top Reflector Handle Lantern Parasol Side Panels Parasol Top Panel Regulator Fixings Supplied Pa cmon ann or f of oa cos mri as 5 16 2 3 Washer aes 1 4
8. er Button Washer E 1 4 Hex Bolt C CERI 1 4 Hex Bolts C 1 Unscrew sparker button and insert battery positive side facing outwards Page 9 Assembly Step 8 First connect hose to regulator securely using adjustable wrenches Second screw regulator onto gas cylinder Regulator 7 Position gas cylinder inside cylinder chamber as shown securing with chain Connect the lantern hose to the regulator hose and secure tightly with adjustable wrenches Then attach the regulator to the cylinder turn clockwise to tighten it securely Place cylinder in position as shown Note The cylinder must be positioned as shown in the patio heater cylinder chamber to provide vapor withdrawal Check for Leaks Your patio heater has been checked at all factory connections for leakage To check the connection at the gas hose regulator cylinder 1 Make leakage solution by mixing 50 water with 50 liquid dish soap 2 Brush several drops of the solution onto the gas hose regulator cylinder and hose connection 3 Turn on the gas cylinder valve Inspect the connections and look for bubbles 4 If no bubbles appear the connection Points for leak testing i fe s sale Regulator Cylinder 5 If bubbles appear there is leakage loosen and re tighten this connection If it still leaks please contact customer service on info uigroup ie or 678 534 2876 Hose Regulator
9. is operated Normally the burner flame is blue with yellow flame at the top The Burner mesh will become red hot If flames extend beyond the surface of the burner mesh or the phenomena of flame lift or light back or black spot is accumulating on the burner mesh or reflector the heater should be turned off immediately The heater should not be operated again until the unit is serviced or repaired Yellow Tip Primary blue Reflector flame Burner mesh Care and Maintenance e Regularly clean your patio heater between uses and especially after extended periods of storage Ensure the heater control is turned fully to the off position the gas supply is shut off at the regulator or bottle cylinder valve and the heater and its components are sufficiently cool before cleaning e Never douse the heater with water when its surfaces are hot We recommend that servicing of this appliance should be performed either after every 100 hours of use or annually which ever is achieved soonest Fixings All screws and bolts etc should be checked and tightened on a regular basis Storage e Remove battery from ignition unit during prolonged periods of non use Do not leave the patio heater exposed to outside weather conditions or stored in damp moist conditions To save space during long term storage the reflector can be removed Take care to ensure the shape of the reflector is not damaged or deformed as this will affect performa
10. n Heater Injector Size Setting Pressure Regulator Outlet Pressure Standard Gas Supply Pressure Specifications are subject to change without prior notice Universal Innovations Kilcoole Ind Est Kilcoole Co Wicklow Ireland Shall be used only in a well ventilated space and shall not be used in a building garage or any other enclosed area May be installed in shelter no more inclusive than With walls on all sides but with no overhead cover 40 Within a partial enclosure which includes an overhead cover and no more than two side walls These side walls may be parallel as in a breezeway or at right angles to each other Within a partial enclosure which includes an overhead cover and three side walls as long as 30 or more of the horizontal periphery of the enclosure is permanently open Warranty Keep these instructions for future reference The patio heater has been manufactured under the highest standards of quality and workmanship We warrant to the original consumer purchaser that all aspects of this product will be free of defects in material and workmanship for 1 year from the date of purchase A replacement for any defective part will be supplied free of charge for installation by the consumer Defects or damage caused by the use of other genuine parts are not covered by this warranty This warranty shall be effective from the date of purchase as shown in the purchaser s receipt This warran
11. n and turn to position e While dial is held pressed in at position press spark button to ignite the heater Hold dial in for at least 10 seconds to ensure heater stays lit If heater does not light after holding dial in for 20 seconds wait 5 minutes and try again Do not continuously hold the dial in as you may cause a build up of gas e In windy conditions shield from wind to ensure easy lighting and hold dial in for at least 20 seconds to ensure heater stays lit e Turn control dial to high or low flame position as required e Correct operation of the heater is indicated by a predominantly blue quiet flame If the sparker fails you can light your patio heater using a match To light Patio Heater with match 1 Place lit match through the gap below the burner mesh and wind guard 2 Turn the control dial to the position After burner ignites keep control dial held in for 10 seconds to ensure burner stays lit and then release 3 If the burner does not light after holding the control dial in for 20 seconds with the lit match in position remove the match turn the control dial to the off position wait 5 minutes and then repeat To Turn Off e Push dial in and turn to position O e Turn the gas off and disconnect at the cylinder when not in use e Remove battery from ignition unit during prolonged periods of non use Flame Characteristic The flame pattern at the burner mesh should be visually checked whenever the heater
12. nce Page 15 e When using the heater after extended periods of storage re attach the reflector The heater should never be operated without the reflector in place If the heater is to be stored indoors the gas bottle must be disconnected and left outside in a dry well ventilated area away from any sources of heat or ignition e Do not let children tamper with the bottle Service If your heater needs maintenance or is not working properly please contact your local authorized agent for service It is a necessity to contact an authorized source for replacement of parts and or servicing This work must be carried out by a qualified gas technician Spare parts may be obtained by contacting our spare parts department by email info uigroup ie WARNINGS NEVER use indoors in an enclosed area or below ground level e This appliance is intended for use with LPG bottled gas only e This appliance features a flame failure and tilt device In the event of a wind blowing the flame out or the unit being tipped over the gas supply will be cut off from the cylinder In this event the knobs should be set to off and you should wait 5 minutes before re lighting e Failure to read and follow these instructions could result in serious injury or damage to property e This product will become hot when in use take care when touching e Keep children and pets at a safe distance from the unit when in use DO NOT move this product when in use
13. nly use with gazebo s specifically designed to be used with patio heaters e Ensure the heater is at a safe distance from glass and PVC doors and windows to stop damage from any heat build up e Read the warnings and use instructions before operation Warning Do not leave the heat focusing reflector of the patio heater in the tilt position during rain or windy conditions or when the patio heater is not in use or unattended Always position the heat focusing reflector in the full down position when not in use or during windy or rainy conditions DURING RAIN HIGH WIND CONDITIONS OR WHEN UNATTENDED Page 16 CAUTION e It is normal for the heater to smoke during the first few minutes of use If you smell gas turn off the appliance and extinguish all flames If the odour continues immediately contact your gas supplier e In the event of an uncontrollable fire immediately disconnect the gas cylinder moving it away from fire and contact the fire services DO NOT PUT YOURSELF AT RISK e Ensure aerosols are not used near this unit when in use Ensure all packaging and plastic bags are disposed of safely Technical Data Overall Height Overall Weight Overall Width Heater Heat Input Qn 86 6 approx 82 6lbs 34 38 200 Btu h 2 0 Lbs per hour 0 07 11 per W C 11 per W C ANSI Z83 26a 2008 CSA 2 37a 2008 Gas Fired Outdoor infrared Patio heaters Max 250 PSI MIN 5 PSI Heater Gas Consumptio
14. rformed in a well ventilated area e Confirm all control knobs are in the off position Open the gas control valve on the bottle e Check for leaks by brushing a solution of 50 water and 50 dish soap over the gas system joints including all valve connections hose connections and regulator connections NEVER USE AN OPEN FLAME to test for leaks at any time If bubbles form over any of the joints there is a leak e Turn off gas supply and retighten all joints e Repeat test If bubbles form again do not use the patio heater Please contact the helpline stated in this manual e Leak test annually and whenever the gas bottle is removed or replaced Gas and Regulator e The gas hose must be connected in accordance with these instructions When installed correctly all parts of the hose should be contained within the Patio Heater pole and gas cylinder chamber No part of hose should be outside of the Patio heater body where it could be a trip hazard or could be accidently damaged This appliance is for propane use only See instructions supplied with regulator for correct use and attachment e Gas bottles should never be stored on their side e Never store gas bottles indoors e This appliance is supplied with a propane regulator which must only be used for propane gas NEVER use an adjustable regulator with this appliance e Please consult your gas dealer for the most suitable gas bottles for your regulator Siting Instructions
15. rns or clothing ignition e Young children should be carefully supervised when they are in the area of the heater e Clothing or other flammable materials should not be hung from the heater or placed on or near the heater e Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater e Installation and repair should be done by a qualified service person The heater should be inspected before use and at least annually by a qualified service person More frequent cleaning may be required as necessary It is imperative that control compartment burners and circulating air passageways of the heater be kept clean e Keep the appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids Do not obstruct the flow of combustion and ventilation air e Keep the ventilation opening of the cylinder enclosure free and clear from debris An appliance may be installed with shelter no more inclusive than a With walls on all sides but with no overhead cover b Within a partial enclosure which includes an overhead cover and no more than two side walls These side walls may be parallel as in a breezeway or right angles to each other c Within a partial enclosure which includes an overhead cover and three side walls as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open The LP gas supply cylinder to be used must
16. ty is valid for the original customer only and excludes product damage due to shipment or failure which results from alteration product abuse or product misuse whether performed by a contractor service company or consumer We will not be responsible for labor charges and or damage incurred in installation repair or replacement nor for incidental or consequential damage Contact info uigroup ie Tel 678 534 2876 Page 17
Download Pdf Manuals
Related Search