Brondell S1000-EW Use and Care Manual
Contents
1. Ei wy 2 Turn Off Water Supply Valve and Flush Toilet a Turn water valve off completely to stop the flow of water b Flush toilet and hold down handle to completely empty tank c Disconnect water supply hose from toilet tank Important notes e You may wish to place a container under the tank to catch any excess water e Do not continue without completing the above steps Failure to do so could result in flooding leaking or damage to the Swash 3 Connect T Valve to Water Supply Line and Toilet Tank Note Do not connect the T Valve or bidet hose to a hot water line only connect to the cold water pipe failure to do so could cause the bidet seat to malfunction or become damaged Note If your water supply line is rigid you may need to replace it before continuing Swash 900 1000 INSTALLATION a Install the T Valve with the rubber washer to the incoming water Steps 3a amp 3b connection on the bottom of your toilet tank Be sure that you place the flat edge of the rubber washer into the T Valve against the metal with the raised lip facing the toilet tank connection b Connect the water supply line coming from the wall to the bottom of the T Valve 4 Connect Bidet Hose to T Valve a Connect one end of the bidet hose to the T Valve and set aside 5 Install Mounting Plate amp Attach Swash a Place adjustable mounting plate over mounting holes on toilet flat side down black rubber side of mounting plate should be2. Swash 900 1000 OPERATION Water Flow Water Pressure Adjustment While the cleansing function is operating press the Water Pressure Dry Temp and buttons on the remote control to increase or decrease the water pressure of the spray There are 3 water pressure levels Low Med High Wide Spray To adjust the spray width of the washing stream during a cleansing cycle press the Wide Spray button The Wide Spray button has 3 levels indicated by lights on the remote above Wide Spray button Concentrated Stream Blue Medium Stream Pink Wide Stream Red Move Nozzle Oscillation Function Swash 1000 Only While the wash function is operating press the MOVE button on the remote control to start or stop the nozzle oscillation function moving back and forth This provides a wider range of cleansing spray Warm Air Dryer Swash 1000 Only Once the wash cycle is complete press the DRY button to activate the warm air dryer The dryer will run for approximately 2 minutes To keep the dryer continuing longer than 2 minutes press the DRY button again during the drying cycle Each time your press the button during the drying cycle the 2 minute Cycle starts again If you would like to stop the dryer cycle before a 2 minute cycle ends press STOP button to discontinue Adjusting Seat Water and Dryer Temperature Seat Temperature Press Seat Temp button to adjust the seat temperature to desired level There are four
3. closest to the toilet tank and rubber should be against the ceramic b Place adjustable metal brackets flat side down in the center of the square opening in the mounting plate and insert mounting bolts through adjustable metal brackets and mounting holes Be sure that the square mounting bolt head is even with sides of adjustable metal bracket c Slide rubber cone washer flat washer and then barrel nut onto mounting bolts under the toilet bowl and tighten to keep mounting plate in place d Set the Swash flat on the toilet bowl in front of the mounting plate and slide seat onto plate until it is secure and clicks into place e If the seat appears too short or too long for the toilet adjust the mounting plate accordingly To adjust the mounting plate loosen barrel nut and slide seat forward or backwards as needed Once the seat is lined up properly tighten barrel nuts to hold in place 6 Connect the Bidet Hose Step 6 a Connect the bidet hose to the side of the bidet seat making CK sure the hose is firmly connected Take care not to twist the bidet i N hose excessively bend it or strip the plastic screw threads an when screwing the hose onto the bidet seat 7 Turn On Water Supply a Open the main water supply valve slowly and check for leaks b Wait 5 minutes check again and if there are no leaks continue 10 Swash 900 1000 INSTALLATION 8 Connect Power a Plug the power cord into the electrical outle
4. temperature levels indicated by lights on the remote above Seat Temp button Low blue Med Pink High Red Off No Light Water Temperature While wash function is operating press Water Temp button to adjust temperature to desired level There are four temperature levels indicated by lights on the remote above Water Temp button Low blue Med Pink High Red Off No Light 16 Swash 900 1000 OPERATION Warm Air Dryer Temperature Swash 1000 Only While air dryer function is operating press the Water Pressure Dry Temp button and to adjust warm air dryer temperature to desired level There are 4 levels for the warm air dryer Low Med High Off Additional Features Deodorization Swash 1000 Only When you sit down on the seat the deodorizing function starts automatically on a low setting To activate the deodorizer on a high setting press the Deodorize button on the remote control The deodorizing function will run on high for approximately 1 minute To stop the function prior to 1 minute press STOP button at any time Nozzle Sterilization Swash 1000 Only To sterilize the stainless steel nozzles press the Sterilize button on the remote control and a cleansing silver oxide nano particle water treatment begins The cleansing spray will last for approximately 30 seconds To stop the function prior to 30 seconds press the STOP button at any time The silver oxide nano particle treatment system has p
5. ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ANY IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY SOME STATES DO NOT ALLOW LIMITATIONS SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY WARRANTS THAT THE PRODUCT WILL BE FREE FROM MANUFACTURING DEFECTS WHICH AFFECT THE ABILITY OF THE PRODUCT TO OPERATE FOR ITS INTENDED USE IT IS NOT A WARRANTY THAT THE PRODUCT WILL NEVER REQUIRE REPAIRS OR TO UNDERTAKE RESPOSIBILITES LIABILITIES OR OBLIGATIONS OTHER THAN THOSE SPECIFICALLY IDENTIFIED IN THE PRECEDING SECTIONS BRONDELL IS NOT RESPONSIBLE OR LIABLE FOR PERSONAL INJURY OR PROPERTY DAMAGE OF ANY KIND EVEN IF ARISING FROM A BREACH OF THIS WARRANTY How to Obtain Service To obtain repair service under this warranty you must contact an authorized BRONDELL Service Center to obtain an RMA Return Merchandise Authorization number Proof of purchase in the form of a copy of your original receipt must accompany the returned unit for the warranty to be valid Take or ship the unit pre paid to the closest Brondell authorized service center along with your RMA number and proof of purchase To obtain your RMA number and locate the BRONDELL Service Center location nearest you call 1 888 542 3355 25 Porondell a better bathroom experience For questions contact Brondell Customer Service 1 888 5
6. Swash 900 1000 OPERATION Quick Reference Guide Remote Control Display Control panel Display Control panel Remote control signal transmitter Rear button Front button Stop button Dry button Move button Water Pressure Dry i Temp button 7 Nozzle Position Water Pressure button Dry Temp Water Temp indicator Seat Temp indicator 2 Wide Spray button Wide indicator ey Water Temp button 10 Seat Temp button gP T D D D D D D D D D D D D D OD D D D GOD GOD GOD GOD GOD GOD GOD GOD GOD GOD GOD OP P D Gimp i Sterilize button eum a Gum Gum em f em em em em em em KA Pl Deodorize button Pd For the Swash 900 models the Move Dry Sterilize and Deodorize functions are excluded WS brondell 13 Swash 900 1000 OPERATION Display Q Remote control signal transmitter Transmits the signal when a remote control button is pressed 9 Seat Temp indicator Whenever the Seat Temp button is pressed the temperature control indicator cycles through the following options L Blue gt M Pink gt H Red Off Seat Temp Control panel Rear 6 Stop Ob Move Rear button Use this button to use the rear cleansing function Stop button All currently operating functio
7. Swash 900 1000 SAFETY PRECAUTION A Danger If not observed serious injury or even death may occur as a result of electrocution Warning If these warnings are not observed considerable physical injury or property damage may occur as a result of burns electrocution or fire IN Caution If these cautions are not observed slight physical or property damage may occur READ ALL INSTRUCTIONS BEFORE USING Save these instructions for future reference When using electrical products especially when children are present basic safety precautions should always be taken A Danger Failure to observe the following warnings may result in electric shock fire personal injury property damage or product damage e Do not use the product with a damaged power plug or loose electric outlet e Do not move the product or unplug it by pulling the power cord e Do not handle the power plug with wet hands e Do not forcefully bend the power cord or place heavy objects on it to prevent it from being damaged or deformed e Do not connect and pull out the power plug repeatedly e Unplug the product before cleaning repairing inspecting or replacing parts e Remove any dust or water from the power plug e Do not plug the appliance into an electrical outlet or power strip that is being used by too many appliances Use an electrical outlet adequate for the wattage of the product e f the power cord is damaged do not attempt to repair modify or r
8. calling the Brondell Service Center as most issues are easily resolved with a few simple steps If you are unable to resolve the issue after checking the following items please call the Service Center at 888 542 3355 or email us at support brondell com Check before continuing e Make sure the Swash is connected to power and that the outlet is working properly e Make sure you check amp test the reset button on the GFI outlet Standard 120V GFI outlet e Make sure the Remote Control has fresh batteries and they are installed correctly 3 x AAA e Make sure main water supply valve is open e Make sure the seat is not in Eco Mode e Confirm there are no leaks from hoses or water supply e Make sure Mesh Filter is clean and free of build up or debris see maintenance section After checking items above refer to the following troubleshooting chart for additional solutions 21 Swash 900 1000 TROUBLESHOOTIN Possible Causes Possible Solutions The bidet seat is not working Product shuts off during use Low water flow or spray pressure Nozzles do not function properly Bidet wash feature does not work or fails to spray 1 Bidet not plugged in 2 No power to Swash 3 There is power but nothing happens when trying to use the Swash 4 Not activating body sensor 1 Washing or drying time exceeded the cycle time 2 Power failure 1 Clogged filter 2 Water supply valve not opened fully 3 Nozzles dirty 4 E
9. commercial hospital or other high use non residential applications Residential Warranties for Swash High Tech Toilet Seat Products Swash 900 Models One Year Limited Warranty e 10096 Coverage of all parts and labor for the entire product for the first year from original date of purchase Swash 1000 Models Three Year Limited Warranty e 10096 Coverage of all parts and labor for the entire product for the first year from original date of purchase e 75 Coverage of all parts and labor for the entire product for the second year from original date of purchase e 5096 Coverage of all parts and labor for the entire product for the third year from original date of purchase Exclusions and Limitations 1 BRONDELL warrants its products to be free from manufacturing defects under normal use and service This warranty is extended only to the ORIGINAL PURCHASER 2 BRONDELL s obligations under this warranty are limited to repairs or replacement at BRONDELL option of products or parts found to be defective provided that such products were properly installed and used in accordance with instructions BRONDELL reserves the right to make such inspections as may be necessary in order to determine the cause of the defect BRONDELL will not charge for labor or parts in connection with warranty repairs for the first full year from date of purchase on all products except those that may be subject to commercial use limitations 3 BRONDELL is not respons
10. water quality It is recommended to check the filter at least once every year Turn off the water supply unplug the Swash and remove seat from toilet using Quick Release button on left side of unit slightly below amp behind the bidet hose inlet Remove Mesh filter by turning with a Phillips head screw driver Clean the filter with toothbrush while running under tap water to effectively remove any foreign substances or build up Replace Mesh filter and carefully check that it is installed properly If improperly installed it could result in the product leaking Replace seat and turn water supply back on 20 Swash 900 1000 MAINTENANCE Product Storage amp Use Short term non use If the product will not be used for more than a few weeks you can simply unplug it You may also consider shutting the water supply off at the wall for extra precaution Long term non use If the product will not be used for an extended time longer than 4 months you should unplug the unit shut the water supply off at the wall and then drain the hot water heater To drain the hot water heater remove the drain plug on the back of the bidet seat by turning it counterclockwise by 90 degrees so that it is horizontal figure 1 and then pulling it forwards figure 2 so that any residual water in the tank drains out TROUBLESHOOTING If the bidet appears to be operating abnormally please review the troubleshooting tips before
11. 00 INSTALLATION Installation Parts 1 2 ea Mounting Bolt 2 2 ea Rubber Cone Washer 3 2 ea Flat Washer 4 2 ea Barrel Nut 5 Mounting Plate 6 2 ea Adjustable Bracket 7 Rubber T Valve Washer 8 T Valve Connector 9 Bidet Hose 10 Remote Control w Wall Mount 11 2 ea Remote Screw 12 2 ea Remote Anchor 13 3 AAA Batteries Swash 900 1000 INSTALLATION Before Installation Check water supply line Check the line that connects the toilet tank to the water shut off valve If it is a rigid pipe you may need to purchase a flexible hose to replace it before installing the Swash The length of the hose and the size of the connectors will vary Residual moisture is normal Every product is tested with pure water during production to ensure the highest quality and performance It is normal to find a small amount of residual moisture on the product and in the reservoir and filter Tools A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a standard wrench may be needed for tight water supply connections Installation Please read these instructions carefully before installing the Swash Failure to do so could result in flooding leaking or damage to the product 1 Existing Toilet Seat Removal a Lift hinge covers and use a screwdriver to remove the mounting bolts b Remove the toilet seat Note Steps may vary by type of seat Step 2c les
12. 42 3355 CONTACT INFORMATIO Brondell Inc PO Box 470085 San Francisco CA 94147 0085 Phone 1 888 542 3355 Email support brondell com Web www brondell com WARRANTY For detailed warranty information and product registration please go on line at www brondell com Please retain receipt records for any warranty claims 26
13. Swash 900 1000 OWNER SIMANI Wbrondell S1000 EW 5S1000 RB S1000 RW S900 EW S1000 EB S900 RW Swash 900 1000 This manual contains important safety information Before operating the unit please read this manual thoroughly and retain it for future reference TABLE OF CONTENTS Section 1 Product Features page 1 Section 2 Safety Precautions page 2 4 Section3 Parts amp Configuration page 5 7 Section 4 Installation page 8 11 Section 5 Operation page 12 18 Section 6 Specifications page 19 Section7 Maintenance page 20 21 Section8 Troubleshooting page 21 23 Section9 Warranty Information page 24 25 Swash 900 1000 PRODUCT FEATURE Swash 900 and Swash 1000 Models Ergonomic heated seat with four temperature settings High Med Low Off Instant and endless warm water the cutting edge instant ceramic heating system ensures an endless warm water stream for posterior and feminine washes while reducing power consumption by up to 6096 over conventional storage tank systems Dual stainless steel nozzles separate stainless steel nozzles resist soiling and bacterial contamination for enhanced hygiene The dual nozzle configuration ensures accurate coverage for all types of users Wireless remote control the intuitive remote control comes with convenient mounting bracket and includes its own Eco Mode to conserve battery life Wide spray option 3 stage width settings widens the wash spray from a s
14. button to engage 3 levels of the warm air dryer Swash 1000 models only IJ Water Pressure Dry Temp button You can control the water pressure in 3 levels L gt M H and control the air dryer temperature in 4 levels LM HOFF using the Water Pressure Dry Temp button You can control the water pressure when operating the rear cleansing front cleansing functions and control the air dryer temperature when operating the drying function EJ Wide Spray button Seat 10 Temp Deodorize 12 14 Use this button to control the width of the water spray stream during the front or rear wash cycle You can select from 3 levels Concentrated Stream Blue Medium Stream Pink Wide Stream Red Seat Temp button Use this button to control the seat temperature Whenever the Seat Temp button is pressed You can control the seat temperature in 4 levels L gt M H Off Deodorization button Use this button to perform the deodorization function When you press this button the deodorization function is performed for approximately 1 minute Swash 1000 models only Swash 900 1000 OPERATION Using the Swash Important note The wash functions and the warm air dryer function will not work unless the body sensor in the seat detects someone sitting down skin conductivity sensor To override the safety sensor please refer to the section in the manual called Configuring a Special Mode Important n
15. disease e Do not block the warm air outlet with your hand or other object e Turn off the main water supply valve when cleaning the filter e For children and seniors who may have difficulties with adjusting temperature or those with sensitive skin or impaired heat sensitivity set the temperature of wash spray warm air dryer and seat to low or off to prevent burning e Close supervision is necessary when this product is used by children or persons requiring general assistance e Do not press the buttons using excessive force e Do not stand or place heavy objects on the seat cover e Use this product for its intended use only as described in this manual Do not use any attachments that are not recommended by Brondell e Do not use the product outdoors or operate where aerosol spray products are being used or where it could be exposed to pure oxygen without proper ventilation e Connect this product to a properly grounded outlet only Refer to the Grounding Instructions N Caution Failure to observe the following warnings may result in electric shock fire personal injury property damage or product damage e Do not connect the main water to the hot water pipe only connect to cold water supply e After the installation make sure to check all water supply connections for leaks Rubber washers should be in place for the water connection hoses amp T Valve 3 Swash 900 1000 e Do not open close the seat cover using
16. emp indicator light is turned off this indicates seat sensor lock mode has been cancelled 3 The new setting will automatically be saved within 10 seconds if no other buttons are pressed 18 Swash 900 1000 SPECIFICATIONS Round 15 Width x 19 4 Depth x 5 66 Height in inches Dimensions Elongated 15 Width x 20 8 Depth x 5 66 Height in inches Weight 13 2 Ibs round 14 3 Ibs elongated device Warm water temperature control 4 levels Off Room temperature L 88 7 M 94 1 H 99 5 in Fahrenheit Power consumption by heater 1200 W Bimetal temperature sensor temperature fuse overheating prevention micro switch Warm air temperature control 4 levels Off Room temperature L M H Air dryer Standard time Drying for 2 minutes device Power consumption by heater 180 W Safety devices Safety devices Bimetal temperature fuse overheating prevention Seat temperature control 4 levels Off Room temperature L 87 8 M 93 2 H 98 6 in Fahrenheit Safety devices Bimetal temperature fuse overheating prevention MESH filter Specifications 25 2 mm Length x 19 8 mm Remote 2 Width x 5 Length x 1 Depth Remote w holder 2 5 Width x 5 5 Length x 1 1 Depth Remote control dimensions Weight limit for Swash 900 1000 330 Ibs Operating temperature 32 104 in Fahrenheit The specifications are subject to change without prior notice for reasons
17. eplace the cord yourself Call a Brondell Service Center e f the product produces a strange noise a burnt smell gets hot or emits smoke unplug it immediately from the electrical outlet and call Brondell Do not use the product until it has been repaired e Do not insert a wire or sharp object in any product gaps or the warm air outlet e Do not place an electric heater near the product or dispose of any burning materials in the toilet e Do not place any liquids or any flammable material on top of the product e Do not use the product in locations exposed to excessive moisture and do not splash liquids onto the product Swash 900 1000 SAFETY PRECAUTIONS e f foreign material enters the product pull the power plug out of the electrical outlet turn off the main water valve and call the Brondell Service Center e Do not disassemble repair or modify the product yourself e Do not use the product while wet or place the product where it can fall into a tub or sink e Do not reach for the product if it has fallen into water Unplug the product immediately and call the Brondell Service Center Wa rning Failure to observe the following warnings may result in electric shock fire personal injury property damage or product damage e Do not operate or store the unit in locations where flammable or combustible materials are used e Do not use industrial water or gray water for the water supply as this may cause skin damage or
18. et cools down The fuse will automatically reset 1 During the drying function adjust the temperature by pressing the air dryer temperature button on the remote control 1 The water that comes out between the nozzles before or after a wash cycle is the self clean cycle and is not a malfunction 1b Residual water may drip into the bowl for several seconds after a wash cycle self clean cycle or nozzle sterilization cycle and is not a malfunction 1 Make sure that the rubber gasket is inserted correctly into the T valve flat side down with lip pointing up towards the toilet tank connection and firmly tighten the connector 2 Make sure that the bidet hose is correctly connected and tight Check any rubber washers and do not over tighten 3 Check if there is anything between the mesh filter and bidet Remove clean and reinstall mesh filter Check if the filter is damaged see maintenance section 4 Checkthe water tank plug in the back of the seat see maintenance section under product storage and use Brondell Warranty Policy Brondell products are backed by some of the most comprehensive warranties in the industry Brondell warrants that all products excluding consumable items shall be free from defects in material and workmanship under normal use and service Commercial Warranty Warranty period 1 year from original purchase date for all Brondell products Warranties may not apply to products that are used for heavy
19. excessive force e Exercise caution that urine does not come into contact with the nozzles or warm air dryer outlet failure to do so may result in bad odors or malfunction e f the product will not be used for a long period of time unplug the power cord close the main water supply valve and drain any water in the water tank e Do not pull out the bidet hose or connection hose using excessive force e Do not use thinner benzene acidic chemicals chloride or hydrochloric acid detergent This may result in corrosion to the metal parts or discoloration or scratches to the bidet body e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Grounding amp GFI Outlet Instructions This product should only be used with a Grounded GFI Outlet Bidet Seat Cord grounded GFI Ground Fault Interrupter with Grounding Pin outlet and a grounded 3 prong electrical cord as shown in figure A In the event of an electrical short circuit using a grounded GFI outlet reduces the risk of electric shock This product is equipped with agrounded cord and is for use on a nominal120V circuit only min 15 amps and must be plugged into an outlet that
20. ible for the cost of removal return shipping and or reinstallation of products This warranty does NOT apply to a Damage or loss which occurs during shipment b Damage or loss sustained through any natural or manmade causes beyond the control of BRONDELL including but not limited to fire earthquake floods etc c Damage or loss resulting from sediments or foreign matter contained in a water system 24 d Damage or loss resulting from negligent or improper installation including installation of a unit in a harsh or hazardous environment e Damage or loss resulting from removal improper repair modification of the product or improper maintenance including damage caused by chlorine or chlorine related products f Damage or loss resulting from electrical surges electrical outages lightning strikes or other acts which are not the fault of Brondell or which the Product is not specified to tolerate 4 This warranty gives you specific legal rights You may have other rights which vary from state to state THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY BRONDELL REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER BRONDELL SHALL NOT BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE PURCHASER OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL OR COSTS OF REPAIRS BY OTHERS OR FOR
21. is properly grounded with a GFI Receptacle breaker as shown Replace or repair a damaged cord immediately Grounding Pin Extension Cord If itis necessary to temporarily use an extension cord only use a heavy gauge extension cord rated for at least 1500 Watts that has a three prong grounding plug Replace or repair a damaged cord immediately Swash 900 1000 PARTS amp CONFIGUR The Swash 900 and the Swash 1000 have the following dimensions The Swash 900 and 1000 Round Size 202 mm 382 mm 411 mm 7 9 inch 15 inch 16 2 inch 5 3 inch 13 8 inch The Swash 900 and 1000 Elongated Size 202 mm 382 mm 411 mm 7 9 inch 15 inch 16 2 inch 5 3 inch 15 2 inch Bottom View Distance Between Mounting Holes 140 mm 210 mm 140 mm 210 mm 5 5 8 3 inch 5 5 8 3 inch P 49 mm 1 9 inch Rear fixing distance 164 mm 6 5 inch PARTS amp CONFIGUR Product Configuration 1 Lid 2 Warning sticker 3 IR sensor 4 Nozzles 5 Body seat sensor 6 Bidet seat 7 Bidet hose a N e Swash 900 1000 8 T valve connector 9 Power cord 10 Production sticker 11 Drain plug 12 Quick release button 13 Mounting plate 14 Mesh filter Swash 900 1000 REMOTE CONTROL Seat Wide Water Temp Spray Temp 2 Deodorize iwbrongell Temp Spray Temp N brondell Swash 900 Swash 1000 Swash 900 10
22. k Reference Guide Bidet Seat Note Basic functions such as Rear Cleansing and Nozzle Cleaning can be used without the remote by utilizing the auxiliary buttons shown here Seat Display E Auxiliary control panel x Y I L L l L I 4 seat temp Seat Display Remote IR Receiver power 9 Power indicator Receives signal This indicator is turned on when the from remote control bidet power is turned on This indicator is turned off when bidet eco mode is activated gq Remote IR Receiver O eco mode Eco mode indicator Receives signal from If you activate the eco function this remote control indicator is turned on when eco mode starts Q seattemp 3 Seat Temperature indicator This indicator represents the seat temperature Indicator on L M H Indicator off OFF This indicator is turned off when bidet eco ili de is activated Auxiliary control panel mode is activate 1 Power button 2 Rear Cleansing button Turns the product ON OFF nr Selects the rear cleansing function Press and hold the button for more than 2 seconds to turn off If the Power button is pressed while the front rear cleansing function is operating the cleansing function is stopped and the bidet changes to standby mode B Nozzle Cleaning button Peres When pressed the nozzles fully extend allowing for easy cleaning Press again for the second nozzle to extend and once more to retract 12
23. ns will stop Move Nozzle Oscillation button This button engages the oscillation function on the front or rear nozzles during a wash cycle Nozzle oscillation moves the wash wand back and forth to clean a wider area Swash 1000 models only Nozzle Position button Use this button to control the nozzle position during the rear cleansing front cleansing operation You can move the nozzle in 5 levels using the Nozzle Position button Nozzle Position Water Temp button Use this button to control the water temperature Whenever the Water Temp button is pressed you can control the water temperature in 4 levels L gt M H Off Water E Temp Sterilization button Use this button to perform the sterilization function Sterilizing water is ejected for 30 seconds to sterilize and clean the nozzle Swash 1000 models only Water Temp 3 Dry Temp Quick Reference Guide Remote Control Page 2 o Water Temp indicator Whenever the Water Temp button is pressed the temperature control indicator cycles through the following order L Blue J2M Pink H Red Off Wide Spray indicator When the Wide Spray button is pressed the indicator cycles through the following options Concentrated Stream Blue Medium Stream Pink Wide Stream Red Front button Use this button to use the front cleansing Front function Dry button Use this
24. of improving the product performance 19 Swash 900 1000 MAINTENANCE Seat Cleaning and Removal Important Unplug the Swash from the power source before cleaning or removing the seat Use a soft damp cloth and mild cleanser such as dish soap Simple Green or Windex to wipe down the seat DO NOT scrub or use harsh abrasive products to clean the Swash DO NOT use thinner benzene acidic chemicals chloride or hydrochloric acid detergent This may result in corrosion to the metal parts or discoloration or scratches to the bidet body For a more thorough cleaning you may remove the Swash To remove the seat press the Quick Release button on the left side of the Swash slightly below amp behind the Bidet Hose inlet on the seat and slide the seat forward off of the mounting plate and toilet Nozzle Cleaning Press the Nozzle Cleaning button on the Auxiliary Control panel on the side of the Swash The front wash nozzle will fully extend Gently clean the nozzle with a soft cloth or toothbrush Press Nozzle Cleaning button again and the front wash nozzle will retract and rear wash nozzle will fully extend Gently clean the nozzle with a soft cloth or toothbrush Press Nozzle Cleaning button a third time and rear nozzle will retract back into seat Take care when cleaning the nozzles not to apply too much pressure to avoid damaging the nozzle system Cleaning Mesh Filter Cleaning intervals will differ depending on use and
25. ote The remote control will not operate the Swash if the batteries are weak dead or not installed properly remote requires 3 x AAA batteries to function Warm Water Wash Sit on the seat and press the FRONT or REAR button on the remote to begin water flow The nozzles will self clean and purge a small amount of water which will last for several seconds prior to starting the wash function The front or rear wand will then extend and wash for approximately 1 minute then turn off automatically To keep the wash continuing longer than 1 minute press the FRONT or REAR button again during the cleansing cycle Each time your press the button during the cleansing cycle the 1 minute cycle starts again If you would like to stop the wash before a 1 minute cycle ends press STOP button to discontinue flow While cleansing users can adjust the water temperature water pressure spray width and nozzle position according to their preferences After the cleansing cycle the nozzles will perform a self clean cycle purging water for approximately 5 seconds You cannot increase the water pressure level higher than level 2 under the following conditions Main water supply temperature is under 50 degrees F 10 degrees C OR if the rated power source is under 110V Nozzle Positioning While the cleansing function is operating use the Nozzle Position up and down arrows on the remote control to move the position of the nozzles and spray 15
26. owerful anti fungal and anti bacterial properties to keep the nozzles clean and corrosion free Auxiliary Controls There are 3 auxiliary buttons on the side of the Swash to be used if remote is unavailable and to set Swash Special Modes 1 Power button Turns the product On Off Press and hold the button for at least 2 seconds to turn off the Swash Note if the Power button is pressed while front or rear cleansing is operating the cleansing function will stop 2 Rear Cleansing Selects the rear cleansing function 3 Nozzle Cleaning To better clean the nozzles press this button the nozzle will extend fully for easy cleaning Refer to Maintenance section for additional nozzle cleaning information Swash Special Mode Operation Swash Eco Mode When Eco Mode is selected If the Seat Sensor is not activated and no buttons on Remote have been active for approximately 10 minutes the seat heater is automatically set to Low temperature to reduce power consumption Once Eco Mode is activated the Eco Mode light on the seat will turn blue and the other lights will turn off 17 Swash 900 1000 OPERATION If no buttons on the Remote control are pressed for approximately 5 seconds the remote display lights are turned off to conserve remote battery life Selecting Cancelling Eco Mode 1 Press and hold down the Power and Rear Cleansing auxiliary buttons simultaneously for approximately 5 seconds until all the seat display light
27. s start flashing 2 Press the Rear Cleansing button to Set or Cancel Eco Mode a If Eco Mode indicator light is turned on this indicates Eco Mode has been set b If Eco Mode indicator light is turned off this indicates Eco Mode has been cancelled 3 The new setting will automatically be saved within 10 seconds if no other buttons are pressed Selecting Cancelling Silent Mode 1 Press and hold down the Power and Rear Cleansing auxiliary buttons simultaneously for approximately 5 seconds until all the seat display lights start flashing 2 Press the Power button to Set or Cancel silent mode a If Power indicator light is turned on this indicates silent mode has been set b If Power indicator light is turned off this indicates silent mode has been cancelled 3 The new setting will automatically be saved within 10 seconds if no other buttons are pressed Selecting Cancelling Seat Sensor Lock Mode This function bypasses the body sensor located in the seat and allows the wash functions and dry functions to operate without the sensor being engaged Use caution in this mode 1 Press and hold down the Power and Rear Cleansing auxiliary buttons simultaneously for approximately 5 seconds until all the seat display lights start flashing 2 Press the Nozzle Cleaning button to Set or Cancel seat sensor lock mode a If Seat Temp indicator light is turned on this indicates seat sensor lock mode has been set b If Seat T
28. t Important Make sure to only use a grounded GFI ground fault interrupter electrical outlet In the case of a short circuit a grounded GFI outlet may help prevent electric shock or injury If using an extension cord is unavoidable use one with grounding terminals for 120V 60 Hz or higher only Installing the Remote Control 1 Battery Installation a Separate the remote control from the magnetic wall mount by pulling apart gently b Turn remote over and open the battery compartment by popping off the battery cover with your finger or small coin Insert three AAA type batteries included as indicated inside battery compartment and replace battery cover c To confirm the batteries are installed correctly press the Stop button and you should see the Wide Spray LED light turn on for a few seconds note the 2 other LED lights may or may not turn on at this time depending on the current settings 2 Mount Remote optional a Identify a location in the bathroom for the remote control that is visible and reachable from the toilet b Depending on the wall type you can install using the supplied screws and anchor mounts or use the provided double stick tape on the back of the remote wall mount Make sure the remote mount is fully secure with either method so that it does not fall and damage the remote control c Place the remote control into the mount as shown 11 Swash 900 1000 OPERATION Quic
29. ter supply valve at wall to fully open 4 If you have an external bidet filter check and replace if necessary 1 Adjust sitting position to fully cover the body sensor Overide the body sensor refer to special mode operation section to unlock body seat sensor Swash 900 1000 Seat not heated Water wash spray not heated Cold air blowing from the air dryer Water flows before or after use Water leaks from areas other than the nozzles TROUBLESHOOTING 1 Seat temperature set to off 2 Resettable fuse blown 1 Water temperature set to off 2 Resettable fuse blown 1 Air temperature set to off 1 Water coming from nozzles 1 Water leaking from the T valve 2 Water leaking from the bidet hose connection 3 Water leaking from under the seat 4 Water leaking from behind the seat 23 Possible Solutions 1 Make sure that the Seat temperature setting is on Low Blue light Med Pink light High Red light Off No light 2 The bimetal resettable fuse may blow if the temperature exceeds over the normal level The bidet will not work and show an error message until the bidet cools down The fuse will automatically reset 1 Make sure that the Water temperature setting is on Low Blue light Med Pink light High Red light Off No light 2 The bimetal resettable fuse may blow if the temperature exceeds over the normal level The bidet will not work and show an error message until the bid
30. trong concentrated stream to a soft spray for a more personal and thorough cleansing Positionable nozzles each nozzle has 5 different positions to ensure the most comfortable and complete cleansing Aerated wash spray micro bubbles introduced into the wash spray create a gentler softer cleansing action designed for sensitive skin In addition the aerated spray reduces overall water consumption and is more effective in cleansing the skin Automatic Eco Mode when engaged the power saving Eco Mode function automatically lowers the seat temperature settings to conserve energy Gentle closing seat and lid slam free gentle closing seat and lid are user friendly Quick release seat quick release push button for easy removal and cleaning of seat and toilet Swash 1000 Models Additional Features Warm air dryer includes adjustable temperature with 3 levels for a completely hands free experience and toilet paper elimination Automatic deodorizer active carbon deodorization begins automatically as soon as you sit on the seat to neutralize odors at the source Nozzle sterilization when activated the silver oxide nano particle wash treatment has powerful anti fungal and anti bacterial properties to keep the dual nozzles cleaner amp more hygienic for a longer nozzle life Nozzle oscillation the move function provides a massaging oscillating cleanse during the wash cycle ensuring a thorough and comfortable cleansing
31. xternal bidet filter 5 Pressure amp wide spray settings 6 Water supply too cold or power source too low 1 Nozzles are dirty 2 Clogged filter 3 Water pressure is too low 4 External bidet filter 1 Body sensor does not detect that you are sitting on Swash 22 1 Make sure the bidet is plugged in 2 Check and reset GFI outlet 3 Check if the Remote control batteries are dead Replace them if necessary 4 Adjust sitting position to fully cover the body sensor Overide the body sensor refer to special mode operation section to unlock body seat sensor 1 Press the wash or dry button during cycle to extend the time see operation section for more information about wash amp dry functions 2 Check and reset GFI outlet 1 Remove clean and reinstall mesh filter see maintenance section 2 Check water supply valve at wall to fully open 3 Clean nozzles see maintenance section 4 If you have an external bidet filter check and replace if necessary 5 Adjust the water pressure settings on the remote to increase and adjust the wide spray settings on the remote 6 Note You cannot increase the water pressure level higher than level 2 under the following conditions Main water supply temperature is under 50 degrees F 10 degrees C OR if the rated power source is under 110V 1 Clean nozzles see maintenance section 2 Remove clean and reinstall mesh filter see maintenance section 3 Check wa
Download Pdf Manuals
Related Search