Eti 54075142 Installation Guide
Contents
1. not attempt installation Contact a qualified electrician Risk of fire or electric shock To prevent wiring damage or abrasion protect wiring from exposed edges of sheet metal or other sharp objects that may be present in the fixture This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY LIGHTING BATTERY TYPE SYSTEMS FOR FLUORESCENT LIGHTING PRODUCTS ETi SSL Inc The Americas Headquarters 26650 Renaissance PKW STE 6 Cleveland OH 44128 Page 1 of 4 z SOLID STATE LIGHTING INC 10 8 2012 Pre Installation Instructions 1 DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT If you presently have dimmer controls you will need to remove them and replace them with regular circuits If you are unfamiliar with electrical installations we recommend you have a qualified electrician do your installation WARNING SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE PANEL BEFORE REMOVING THE OLD FIXTURE Remove the existing fixture Make yourself a sketch of how the current fixture is wired by wire color or mark the wires with masking tape and a pencil so you will know how to reconnect the wires to your new LED fixture This fixture does not use a mounting bracket to2. rt SOLID STATE ET INC 10 8 2012 LED Round Flushmount Items 54074141 54074142 54075142 5 amp 54075141 The product package includes the following components 1 1 Round Flushmount Housing 2 1 Round Flushmount Diffuser shipped as part of flushmount housing 3 3 Wirenuts in parts bag 4 2 1 2 Electrical Box Screws in parts bag 5 1 Installation Manual Product Description and Characteristics LED ceiling light can be directly mounted to the household ceiling and occupies little space It is energy saving environmentally friendly and practically used for emitting soft and even distribution of light IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS THIS PRODUCT SHALL BE INSTALLED IN ACCORDANCE WITH THE LATEST U L SAFETY NEC AND OR LOCAL AUTHORITY HAVING JURISDICTION INSTALLATION SHALL BE PERFORMED BY A QUALIFIED ELECTRICIAN UNDERSTANDING THE CONSTRUCTION AND OPERATION OF THIS PRODUCT AND THE ELECTRICAL REQUIREMENTS INVOLVED DANGER RISK OF ELECTRIC SHOCK DISCONNECT POWER TO LIGHT FIXTURE BEFORE INSTALLATION Risk of fire or electric shock Use only on 100 277 VAC 50 60Hz circuits Installer shall verify operating voltage at the luminaries prior to installation This fixture is designed for indoor use ONLY This installed fixture may not covered by any thermal insulation material Risk of fire or electric shock LED Round Flushmount installation requires knowledge of luminaires electrical systems If not qualified do
3. s product is warranted for a period of 3 years from the date or original purchase against defects in materials and workmanship If this product should fail to operate due to defects in material or workmanship simply call 1 216 468 0232 within 36 months of purchase This product will be repaired or replaced at ETi s option This warranty is expressly limited to repair or replacement of product and liability for direct incidental or consequential damages is hereby expressly excluded Some states do not allow exclusions of direct incidental or consequential damages so the above limitation of exclusion may not apply to you This warranty gives the consumer specific legal rights which vary from state to state WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS MANUFACTURED ETi SSL Inc The Americas Headquarters 26650 Renaissance PKW STE 6 Cleveland OH 44128 Page 4 of 4
4. secure it to the electrical box Instead it is secured to the box by the included screws specifically designed to ground the pan to a metal electrical box For safe operation use only the 1 inch electrical box screws included in the hardware kit Screw them into the electrical box until there is about 3 8 inch between the ceiling and the underside of the screw head Installation Instructions 1 Before beginning assembly installation or operation of product make sure all parts are present Compare parts with package contents list on previous page If any part is missing or damaged do not attempt to assemble install or operate the product Contact customer service for replacement parts Open the 3 diffuser latches figure 1 Install the electrical box screws in the junction box figure 2 Connect the black and the white wires of the fixture with two wires of the same colors from the junction box with the wirecaps Connect the grounding wire of the fixture with the one from the junction box with the wirecap figure 3 Put the fixture plate across the screw of the lock in figure 2 then rotate fixture plate clockwise and lock it tightly with the screw lock figure 4 Securely mount the fixture plate to the junction box firmly figure 5 Turn the 3 diffuser latches to the right until they are closed figure 6 Restore power to the electrical box Turn the light switch on to activate the fixture ETi SSL Inc The Americas Headquar
5. ters 26650 Renaissance PKW STE 6 Cleveland OH 44128 Page 2 of 4 ET td tie mannna INC 10 8 2012 Fig 1 Fig 2 Fig 3 Fig 4 ETi SSL Inc The Americas Headquarters 26650 Renaissance PKW STE 6 Cleveland OH 44128 Page 3 of 4 ET SOLID STATE LIGHTING INC 10 8 2012 Troubleshooting Guide Minor problems often can be fixed without the help of an electrician Before doing any work on the fixture shut off power supply at the circuit panel to avoid electrical shock Problem Possible Cause Corrective Action Power is off Check if power supply is on Fixture does not light Bad wire connection Check wiring Defective switch Test or replace switch Fuse blows or circuit breaker Crossed wires or power wire is se ee Check wiring connections trips when light is turned on grounded out Cleaning Instructions Your fixture is made from quality materials that will last many years with minimum care You may want to periodically clean the diffuser or interior of fixture using a mild non abrasive glass cleaner and a soft cloth DO NOT use solvents or cleaners containing abrasive agents When cleaning the inside of the fixture make sure you have the power turned off and do not spray liquid cleaner directly onto the LEDs LED driver or wiring Imported by ETi Solid State Lighting Inc 26650 Renaissance PKWY STE6 Cleveland OH 44128 Made in China LIMITED WARRANTY Thi
Download Pdf Manuals
Related Search