Tradewinds HD-C3357OY-HN Instructions / Assembly
Contents
1. 16101 16101 PLAIN PANEL ja W LID SUPPORT TABS 32 GAL LINER gt 16101 L HD344 page 3 product dimensions 15 1 4 26 1727 7 373 page 4 HD344 assembly procedures con t STEP 1 Attach first panel 16100 to legs 16100 R L using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole Attach second and third panels to the same legs mentioned previously 16100 R L using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole Hand tighten only STEP 2 Bolt the two remaining legs 16100 R L to the second and third panels using one MB x 30 Hex Bolt and one Split Washer per each bolt hole Insert planter floor into assembled frame and bolt to the three panels using one M6 x 25 Hex Bolt and one Flat Washer and Split Washer and one M6 Hex Nut per each bolt Hand tighten only STEP 3 Attach fourth panel 16100 to legs 16100 R L using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole NOTE Be sure to place floor support on panel under floor prior to bolting Bolt floor to panel using one M6 x 25 Hex Bolt and one Flat Washer and Split Washer and one M6 Hex Nut per each bolt Hand tighten only ST2. per each bolt Hand tighten only STEP 3 Attach panel w hinges 16101 to legs 16101 R L using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole NOTE Be sure to place floor support on panel under floor prior to bolting Bolt floor to panel using one M6 x 25 Hex Bolt and one Flat Washer and Split Washer and one M6 Hex Nut per each bolt Hand tighten only STEP 4 Attach Lid to panel w hinges 16101 using six M4 x 12 Flat Head Phillips Screws Attach one end of cable to panel and the other end to lid using one MB x 30 Hex Bolt each end Tighten with proper tool STEP 5 Level all parts Note Tighten legs to panels first SEE NOTE BELOW Lower lid to closed position and sguare up lid with the panels While one person is holding lid in position a second person tightens floor to panels using proper tools NOTE TIGHTEN BOLTS ON LEGS TO 35 FT LBS EACH 16101 16101 W CABLE ATTACHMENT W HINGES 16101 R 16101 R PADS FOR SURFACE MOUNT GLIDES FOR PORTABLE
3. EP 4 Level all parts Tighten legs to panels first SEE NOTE BELOW Tighten floor to panels using proper tools NOTE TIGHTEN BOLTS TO 35 FT LBS EACH 16100 4 PADS FOR SURFACE MOUNT GLIDES FOR PORTABLE HD344 page 5 product dimensions ae an Each Planter comes eguipped with a 3 16 thick fiberglass reinforced polyester resin liner Standard color black Des 27 at Ti 1 PAR 7 A 2 Each Receptacle comes equipped with a 1 16 thick polyethylene liner Standard color black page 6 HD344
4. eling permanently tighten all nuts bolts and fasteners ES 1 TC IEP 1 ch seat 16104 to leg 16102 using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole TEP 2 tach back 16104 to leg 16102 using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole SIEP S Repeat STEPS 1 and 2 to complete installation for opposite side STEP 4 Level the seat and back tighten with proper tools 16102 L FOR SUR MOUNT installation WARNING The proper installation of products may depend upon many factors unique to the site location or use of a particular product Consult with your contractor or other professional to determine your specific installation regirements HD344 page 2 assembly procedures con t STEP 1 Attach panel w lid support tabs 16101 to legs 16101 R L using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole Attach panel plain and panel w cable attachment to the same legs mentioned previously 16101 R L using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole Hand tighten only STEP 2 Bolt the two remaining legs 16101 R L to the plain and cable attachment panels using one M8 x 30 Hex Bolt and one Split Washer per each bolt hole Insert trash receptacle floor into assembled frame and bolt to the three panels using one M6 x 25 Hex Bolt and one Flat Washer and Split Washer and one M6 Hex Nut
5. model no HD CST TOT HD CSSFSOT HD C553970Y SPRING ARBOR SERIES PORTABLE amp SURFACE MOUNT BENCH RECEPTACLE PLANTER SLAT LINERS maintenance until repairs are made Regular inspection and maintenance of all parts and fasteners is necessary Tighten all bolts and nuts Inspect Tops Seats Legs Braces and Fasteners periodically for wear or vandalism Replace broken or worn parts immediately or take equipment out of service KEEP THIS ASSEMBLY SPECIFICATION SHEET FOR FUTURE REFERENCE HD344 page 1 IMPORTANT Assemblers should be reasonably skilled in the assembly of commercial ass emb ly pro ce dure S grade heavy duty fabricated steel equipment To ensure proper assembly it is suggested that you take adequate time to locate and identify each part To prevent scratching of the finished pieces we recommend this unit to be assembled on a clean flat solid surface with a drop cloth allowing plenty of working room Also please read the instructions and study the sketches very carefully A little extra time spent before assembly will be well worth it in performing a complete proper assembly Please note that all parts have been precut and pre drilled During the assembly process leave all bolts and nuts finger tight until the entire unit is completely assembled This allows room for movement to level or adjust all seats tops benches framework and braces if necessary After final adjustment and lev
Download Pdf Manuals
Related Search