Lawn Genie L7010 Installation Guide
Contents
1. L7010 8 7 03 1 34 PM Page 1 ae The Toro Promise Limited One Year Warranty The Toro Company and its affiliate Toro Warranty Company pursuant to an agreement E between them jointly warrants to the owner against defects in material and workmanship for a period of one year from the date of purchase awn n l a Neither The Toro Company nor Toro Warranty Company is liable for failure of products not manufactured by it even though such products may be sold or used in conjunction with Toro products During such warranty period we will repair or replace at our option any part found to be A U tO m qi C A nti S p h 0 n Valve defective Return the defective parts to the place of purchase n stal latio n and O Q rat 0 n G U ide Our liability is limited solely to the replacement or repair of defective parts There are no 0 other express warranties This warranty does not apply where equipment is used or installation is performed in any ree a to Toro s specifications and instructions nor where equipment is altered B For Models L70 34 L7010 NEITHER THE TORO COMPANY NOR TORO WARRANTY COMPANY IS LIABLE FOR aha are E a Please read instructions completely before PERIODS OF MALFUNCTION OR RESULTING NON USE PROPERTY DAMAGE OR attempting to install or operate the valve PERSONAL INJURY RESULTING FROM INSTALLER S NEGLIGENCE Some states do not allow the exclusion or limitation of incidental or consequential A dama2. timer that uses an approved class 2 24V transformer as a power Source Step 5 Turn the white flow control screw knob clockwise until it seats closing the valve Turn the water supply on The valve will remain closed Step 6 Turn the black manual bleed screw knob counterclockwise This will allow water to flow through the valve as the flow control is backed out Adjust the flow con trol for desired flow Tighten the manual bleed screw and the valve will close Electrical requirements are 18 V ac minimum at the solenoid Inrush volt amps 24Vac 11 50 VA Inrush current 24Vac 0 48 Amps Holding volt amps 24Vac 5 75VA Holding current 24Vac 0 24 Amps NOTE Due to varying regulations check your local codes RELEASED Version Toro 2005 2005
3. ges so the above limitation or exclusion may not apply to you ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE DURATION OF THIS EXPRESS WARRANTY Some states do not allow limitations of how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state can A Premium Watering Systems For Technical Support P O Box 489 Riverside CA 92502 1 800 231 5117 2003 The Toro Company All rights reserved 1095501 Rev C 7 RELEASED Version Toro 2005 2005 L7010 PRESSURE LOSS PSI 8 7 03 1 34 PM Page 2 ly o Lert tt 0 5 10 15 25 30 0 5 10 15 25 30 35 40 FLOW RATE GPM FLOW RATE GPM Recommended Not Recommended Lawn Genie The L7034 3 4 and L7010 1 are anti siphon valves with a flow adjustment screw and can be operated electronically or manually In areas where freezing conditions occur make provisions for draining the system Use a shut off valve installed on the main line feeding the sprinkler system To assure complete drainage of the valve after water supply is shut off electrically energize each valve for at least a few minutes dry run This vents any automatic valve allowing maximum drainage Where local water pressure exceeds 80 psi a pressure regulator should be used See Unifo
4. rm Plumbing Code Sec 1007 b It is advisable to use a regulator with any automatic valve to assure long life as well as uniform and controllable operation The anti siphon valve should be installed 6 12 above the highest head so at no time will the anti siphon valve be subject to back pressure or drainage There must not be any valve downstream of the anti siphon valve See Uniform Plumbing Code Sec 1003 2 7 Check local codes before installation Anti Siphon valves must not be operated continuously for more than twelve 12 hours See American Society of Sanitary Engineering Standard 1001 Sec 1 5 2 4 Step 1 Flush the line thoroughly before installing the valve Use teflon tape on male threads Step 2 Screw the valve onto the supply pipe threads hand tight Use a wrench only to straighten the valve into position Step 3 Screw the outlet pipe into the valve with a wrench hold the valve by hand as the outlet pipe is tightened Step 4 Wiring to the valves can be placed underground under the pipes Use approved underground type wire and be sure all splices are joined with wire nuts and sealed with vinyl cement or other suitable water proofing cement Run one common wire to each location to serve all the valves at that location Use 18 gauge direct burial wire for runs not over 800 feet and 14 gauge wire over 800 feet The wire is available from your dealer in 2 3 4 5 6 7 and 8 color coded wires Connect the solenoid to a
Download Pdf Manuals
Related Search