Viva 7LIECH-SC-SSF Use and Care Manual
Contents
1. pE I Reminder Place drain cap and silicon plug in a safe location so they are not lost IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance TROUBLESHOOTING Dispenser does not operate Make sure the power cord is properly connected to a working outlet Water is leaking Call 855 VIVA 111 for assistance Push buttons are stuck and or faucets are leaking Apply mineral oil baby oil to button slides to reduce friction No water is coming from the taps Make sure the bottle is not empty If so replace it Make sure to push the water controls in fully Rem2. Fill the reservoir with 1 gallon of tap water Dispense 1 cup of water through both faucets to rinse out water ways Remove drain cap and silicon plug Reminder Place drain cap and silicon plug in a safe location so they are not lost Remove remaining water from reservoirs by dispensing from both taps into a pitcher Replace all parts Reminder Don t forget the silicon plug and drain cap Complete the installation and operation instructions within this manual If your water has an off taste Do not return to store Call 855 VIVA 111 for assistance IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance INSTALLATION A CAUTION To prevent accidental tip hazard dispenser must be securely anchored to wall as shown 1 Place dispenser upright 2 Locate dispenser on a hard and level surface in gm a cool shaded location near a grounded wall outlet Notice Do NOT plug
3. IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance ASSEMBLY To prevent accidental tip hazard base supplied must be securely fixed to the dispenser as shown Do NOT operate dispenser without base properly installed Keep plastic bags away from children 1 Remove dispenser from packaging 2 Lay dispenser on its back 3 Position cooler upright Unpack drip tray and insert into dispenser 4 Properly dispose all of packaging IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance CLEANING PRIOR TO INITIAL USE To remove any odors or dust that may collect during shipment you must clean dispenser prior to first use DO NOT PLUG THE COOLER INTO AN ELECTRICAL POWER OUTLET Time Required 40 minutes 1 10 11 12 13 14 15 Remove bottle receptacle by turning it counter clockwise and pulling up Store in a safe place Remove plastic baffle from inside reservoir Clean with warm soapy water rinse then store in a safe place Fill reservoir with a mixture of 1 gallon tap water and 2 tablespoons of unscented household bleach Let sit for 30 minutes Dispense 1 cup of mixture through both fau
4. Plug This model comes set up with a Probe Receptacle 1 No changes are required The Probe will push the Plug out of the way when you place the bottle into the receptacle If Your Water Then Use This Bottle Looks Like Bottle Receptacle 1 Remove bottle receptacle 1 by turning it counter clockwise and pulling up 2 Remove Collar 2 from foam packaging or bag at front of dispenser 3 Align tabs Turn clockwise to secure IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance OPERATION A CAUTION This unit is intended for water dispensing only Do NOT use other liquids Do NOT use for other purposes Warranty is void if used for any other liquids including coffee tea juices beer or wine This dispenser has been designed to use water bottles with 3 amp 5 gallon capacity Do NOT use alternative bottles Initial Set Up Notice To prevent damage to compressor allow unit to sit upright for at least 4 hours prior to operating Remove tamper seal from bottle cap Do NOT remove plastic cap 2 Clean bottle cap and neck with a soft cloth and warm soapy water then rinse 3 Lift bottle and insert onto the probe Apply slight pressure until the plug inside the cap pushes in and the bottle is seated Water will begin to flow into the reservoirs causing air bubbles to form in the bottle 4 Plug cord into a properly g
5. instructions accompanying it then for a period of one 1 year from the date of purchase all parts in such dispenser shall be free from defects in material and workmanship Vendor may require reasonable proof of your date of purchase from an authorized retailer or distributor Therefore you should retain your sales slip or invoice The Limited Warranty shall be limited to repair or replacement of parts which prove defective under normal use and service and which Vendor shall determine in its reasonable discretion upon examination to be defective Before returning any parts you should contact Vendor s Customer Service Department using the contact information listed below If Vendor confirms after examination a defect covered by this Limited Warranty in any returned part and if Vendor approves claim Vendor will replace such defective part without charge If you return defective parts transportation charges must be prepaid by you Vendor will return replacement parts to original purchaser freight or postage prepaid The Limited Warranty does not cover any failures or operating difficulties due to accident abuse misuse alteration misapplication improper installation or improper maintenance or service by you or any third party or failure to perform normal and routine maintenance on the dispenser as set out in the User s Manual In addition the Limited Warranty does not cover damages to the finish such as scratches dents discoloration or
6. electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician Please make sure that ELECTRICAL OUTLET IS PROPERLY WIRED TO CORRECT SIZED CIRCUIT BREAKER OR FUSE AND PROPERLY GROUNDED MUST BE WIRED TO HAVE CORRECT POLARITY IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance TABLE OF CONTENTS Safety Precautions pp 2 Safety Precautions Electrical Reduirements pp 3 Key Information for Future Use pp 4 SpPECINCAI NS cschers eetectin eens ctin sthauccesccahetseubactivecmaieass 5 Parts amp Features pp 5 Assembly Secae cin aseretaice tenes EET ERAEN EDA 6 Cleaning prior to initial use pp 7 Is 8 Installing the Correct Bottle Receptacle pp 9 OPSTAO sic parece ce nE EERE ENEE ENRE EE 10 Proper Care amp Cleaning pp 11 Troubleshootinmg 12 Limited Wamanly oi detaniuk eneutedviauonk teeter iiiver itiiti 13 KEY INFORMATION FOR FUTURE USE Please register your dispenser immediately at www electrotemp com For future support please record your serial number located on label on back of dispenser and date purchased Staple your receipt to manual You will need this information to obtain warranty service Product Hot and Cold Bottled Wate
7. rust after purchase The Limited Warranty is in lieu of all other express warranties Vendor disclaims all warranties for products that are purchased from seller other than authorized retailers or distributors AFTER THE PERIOD OF THE ONE 1 YEAR EXPRESS WARRANTY VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE FURTHER VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL INDIRECT PUNITIVE INCIDENTAL OR CONSEQUENTAL DAMAGES Vendor assumes no responsibility for any defects caused by third parties This Limited Warranty gives the purchaser specific legal rights a purchaser may have other rights depending upon where he or she lives Some jurisdictions do not allow exclusion or limitation of special incidental or consequential damages or limitations on how long a warranty lasts so the above exclusion and limitations may not apply to you Warranty is void if electrical outlet is improperly wired to incorrectly sized circuit breaker or fuse if not grounded properly or wires do not have correct polarity Electrotemp Technologies Inc 406 Watline Avenue Mississauga Ontario Canada L4Z 1X2 888 828 1426 www electrotemp com IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance 7LIECH SC SSFManual VIVA Eng
8. VA Hot and Cold Bottled Water Cooler Model 7LIECH SC SSF USER MANUAL TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE USER MUST READ THIS MANUAL BEFORE ASSEMBLING INSTALLING amp OPERATING DISPENSER SAVE FOR FUTURE USE PN 7LIECH SC SSF 2012 Electrotemp Technologies Inc BF 5M008973X1 VA SAFETY PRECAUTIONS To reduce risk of injury and property damage user must read this entire manual before assembling installing amp operating dispenser Failure to execute the instructions in this manual can cause personal injury or property damage This product dispenses water at very high temperatures Failure to use properly can cause personal injury When operating this dispenser always exercise basic safety precautions including the following Prior to use this dispenser must be properly assembled and installed in accordance with this manual This dispenser is intended for water dispensing only Do NOT use other liquids Do NOT use for other purposes Never use any other liquid in the dispenser other than known and microbiologically safe bottled water Warranty is void if used for any other liquids including coffee tea juices beer or wine For indoor use only Keep water dispenser in a dry place away from direct sunlight Do NOT use outdoors Install and use only on a hard flat and level surface Do NOT place dispenser into an enclosed space or cabinet Do NOT operate dispenser in the presence of ex
9. cets to clean out water ways Place a 2 gallon or larger bucket under the 7 drain plug in the rear of the dispenser Remove aa ii 6 drain cap and silicon plug Ae i ZE TE O JE Reminder Place drain cap and silicon plug in a safe location so they are not lost J Once unit has completed draining empty the i bucket then return it to under the drain cap i o pan EE T Replace drain cap and silicone plug i i Ht L Wipe inside of reservoir with a soft cloth iaaa
10. in power cord yet 3 Position dispenser so the back is at least 4 inches from wall and there are at least 4 inches of clearance on both sides 4 Install Wall Mount Strap to prevent accidental tip over e Unclip strap from back of dispenser e Mount strap 25 inches up from floor directly to wall stud with screw See illustration A If stud is not available insert and turn anchor directly into sheet rock using a Philips screwdriver DO NOT drill hole into sheet rock first when using this anchor Secure strap by installing screw through washer then eyelet in strap and into wall mounted anchor See illustration B e Position cooler in place e Clip strap onto back of cooler to right or left side See illustration C e Adjust length of strap so the dispenser can NOT move forward Note Dispenser can be positioned in a corner but still requires Wall Mount Strap to be installed Lengthen strap so that once installed the dispenser cannot move forward IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance INSTALLING THE CORRECT BOTTLE RECEPTACLE If Your Water Then Use This Bottle Looks Like Bottle Receptacle
11. lish 5M008973X1 1 Rv 143X210mm 2 3 Roshn 4
12. ove bottle receptacle as per page 6 step 1 Shake bottle receptacle vigorously for a few seconds then replace Cold water is not cold lt takes up to one hour after setup to dispense cold water Make sure the back of the dispenser is at least 4 inches from a wall and there is free airflow on all 4 sides of the dispenser Make sure tank is not overfilled Dispense water until bubbles appear in bottle Adjust thermostat by turning clockwise Adjust in a single increment of 30 degrees of a circle the equivalent of 1 hour on a standard analog clock face Wait 1 hour for results If unsatisfactory adjust another 30 degrees clockwise wait then asses results Thermostat is located at back of unit Hot water is not hot It takes 15 20 minutes after setup to dispense hot water Make sure the power cord is properly connected to a working outlet Make sure energy saving switch is ON Dispenser is noisy Make sure dispenser is positioned on a level surface Water tastes bad Drain water from reservoirs and replace bottle with a fresh one Clean dispenser per Proper Care amp Cleaning instructions IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance LIMITED WARRANTY Electrotemp Technologies Inc Vendor warrants to the original purchaser of this dispenser and to no other person that if this dispenser is assembled and operated in accordance with the printed
13. plosive fumes Position back of dispenser no closer than 4 inches from wall and permit free airflow between wall and dispenser There must be at least 4 inches clearance on the sides of the dispenser to permit airflow Use only properly grounded outlets Do not use an extension cord with your water dispenser Always grasp plug and pull straight out from outlet Never unplug by pulling on power cord Do NOT use dispenser if cord becomes frayed or otherwise damaged To protect against electric shock do NOT immerse cord plug or any other part of cooler in water or other liquids Ensure dispenser is unplugged prior to cleaning Never allow children to dispense hot water without proper and direct supervision Unplug unit to prevent unsupervised use by children Service should be performed only by a certified technician Please contact us at 855 VIVA 111 for assistance Turn power switch es ON after cooler is plugged in and fill with water IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance SAFETY PRECAUTIONS Electrical Requirements Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock A 120 volt 60 Hz AC only 15 amp fused electrical supply is required A time delay f
14. r Cooler Model Number 7LIECH SSF Serial ID Number Date of Purchase IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance SPECIFICATIONS Power Supply 4 5 AMP Refrigerant Type R 134A Cold Water Power 100 Watts Cold Capacity Peak Hour 1 0 Gallon 3 79 L Cold Temp Range 3 C 10 C 37 4 F 50 F Hot Water Power 425 Watts Hot Capacity Peak Hour 1 0 Gallon 3 79 L Hot Temp Range 80 C 92 C 176 F 197 6 F Dimensions 91 3 H x 27 5 W x 28 6 D cm 35 4 H x 10 8 W x 11 3 D inch Net Weight 27 9lbs 12 7Kg PARTS amp FEATURES Bottle Probe Q Hot Water Control Child Safety Latch Cold Water Control Hot Water Tap Cold Water Tap 6 Drip Tray Energy Saving Switch Cooling Thermostat Carry Handle Power Cord 44 Drain Plug 2 LED night light 33 Wall Mount Strap and Collar for plain capped bottles Not Shown
15. rounded wall outlet 5 Turn energy saving switch on back of dispenser to ON This switch controls the heating of water If you do not want hot water turn this switch OFF Initial Rinsing of Water Lines This unit has been tested and sanitized prior to packing and shipping During transit dust and odors can accumulate in the tank and lines You must dispense and dispose at least one quart of water prior to drinking any water Dispense Cold Water Note After setup it will take 1 hour to get water to maximum cold temperature During this time the compressor will run continuously This is normal 1 Position bottle glass pitcher or cooking pot securely below cold water tap The circular shapes in the drip plate help align the flow of water This unit dispenses water at a fast rate To avoid splashes hold cup as close to the tap as possible 2 Depress cold water control downward to start flow 3 Release cold water control once desired fill level is achieved IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 855 VIVA 111 for assistance PROPER CARE amp CLEANING General Cleaning Perform As needed Time Required 5 minutes Note Do NOT use abrasive materials or chemical cleaners Clean cabinet surfaces with a soft cloth and warm soapy water then rinse 2 Wipe dust from back of dispenser to improve efficiency 3 Remove drip tray assembly by pulling it forward Remove co
16. use or circuit breaker is recommended Do not overload the ciruit provide separate circuit if required to serve only this appliance This water cooler is equipped with a power supply cord having a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong grounding type outlet grounded in accordance with local codes and ordinances a mating outlet is not available it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician If codes permit and a separate ground wire is used it is recommended that a qualified electrician determine that the ground path is adequate Do not ground to a gas pipe Check with a qualified electrician if you are not sure the water cooler is properly grounded Do not have a fuse in the neutral or ground circuit GROUNDING INSTRUCTIONS For a grounded cord connected water cooler This water cooler must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current This water cooler is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances Improper connection of the equipment grounding conductor can result in a risk of
17. ver Place tray and cover in dishwasher or wipe parts clean with a soft cloth and warm soapy water Cleaning Cold Reservoir and Water Lines Perform Every 3 months or whenever an off taste occurs Time Required 15 minutes Note Best to do prior to loading a fresh bottle Turn energy saving switch OFF Unplug power cord from wall outlet Remove waiter bottle oe IS Unclip Wall Mount Strap from back of dispenser and turn dispenser around so backside is facing away from the wall 5 Place a 2 gallon or larger bucket under the D drain plug in the rear of the dispenser As J Ng a O iy PA Me il iii a SAI Remove drain cap and silicon plug Cold j i Ee water will immediately flow into the bucket i This will be followed several seconds later ei by hot water at temperatures that can i cause severe burns Avoid direct contact with hot water Keep children and pets iret away while draining unit i fe O A VE oO ee z E
Download Pdf Manuals
Related Search