ShelterLogic 78741.0 Instructions / Assembly
Contents
1. ZI ES D IS YOUR COVER PULLED CORRECTLY NeORREGE ON THE FRAME Fig 12B NOTE ShelterLogic logo should line up on the left front and right rear corners near the top rail If it is not legible and positioned as shown above as incorrect the cover has not been put on the frame correctly WARNING Serious injury to persons or property could result if cover is installed and shelter is not completed and is left unattended Shelter must be anchored securely until completed Page 7 WARNINGS CAUTIONS CARE amp CLEANING WARNING Prior to installation consult with all local and municipal codes regarding the installation of temporary shelters Choose the location of your shelter carefully Check for overhead utility lines tree branches or other structures e Do NOT install near roof lines or other structures that could shed snow ice or excessive run off onto your shelter e Do NOT install too close to other structures A MINIMUM of 6 to 10 ft is necessary between structures to allow for snow removal e Do NOT hang objects from the roof structure or support cables e Do NOT smoke our use open flame devices in or around the shelter e Do NOT store flammable liquids gasoline kerosene propane barbeque grills fire pits deep fryers or smokers inside the shelter e Do NOT use hard edged tools or instruments like rakes or shovels to remove snow This could result in punctures in the cover CAUTION 1 PLE2. ground until the eyelet is sticking out of the ground by 1 2 so it can be anchored to the legs Wrap the cable provided through the eyelet of the anchor and around the frame as indicated in Fig 9 Secure the cable with the clamp s provided TO Geet r e m 2 STEP 10 END PANEL INSTALLATION Fig 10A 10B 10C amp 10D Hold the end panel at the top center with the white inner surface facing the inside of the shelter if you have a white shelter the inner surface has the visible weld seams folded around frame and Carefully remove the top rail from the top bend and place rea eas the webbing in between the two The top rail should pass ETP Terr through the loop of the webbing Replace the top rail onto the top bend and secure it with the hardware indicated Slits in fabric fabric i i el m in Fig 10A 10B Remove the nut from the side rail and carefully pull the AG pi Side View side rail away from the ShelterLock the rail only needs to be pulled away enough to pass the webbing through the Fig 10A Fig 10B connection If this connection has the wind brace on it remove the wind brace end before pulling the side rail When the webbing is through replace the side rail and the cross rail if necessary Fig 10C Replace the nut and tighten Repeat this for the other side Locate where the webbing exits the pocket on each side of the end panel Pull the webbing careful
3. 22 W x10 H Peak Style Frame Assembly Please read and understand instructions completely before assembly Layout out frame parts as shown and match up items with quantity to make sure no parts are missing Top Middle Ribs End Rib End Rib Wind Brace Cover Rails Wind Brace ATTENTION FOR MISSING OR REPLACEMENT PARTS OR QUESTIONS Assembly Mfg Assembly Mfg PLEASE CONTACT Reference Part Reference Part CUSTOMER SERVICE 1 800 524 9970 CANADA 1 800 559 6175 11106 ShelterLogic All Weather Shelters www shelterlogic com 150 Callender Road Watertown CT 06795 SS 05 107133 0C 08 31 07 Basic Frame Assembly NOTE FRAME EXTENSION KIT 22 x20 x10 is the base frame dimension Your model may have more middle ribs than shown in the illustration on pg 2 You will receive one extra rib for every extra 4 ft of building length that you purchase The basic frame assembly will remain the same The cover will be the correct size for the length of the building l lt 2 gt STEP 1 PLOTTING THE FRAME Fig 1 Before building your shelter you should choose a flat area on your property and plot your shelter Length 1 Stake out the area for the shelter in the desired spot The width of the area of Building should be at least equal to the width of the shelter and the length should be equal to the length L of the shelter Fig 1 2 To be sure the staked area is square tie a
4. ASE READ AND FULLY UNDERSTAND THE INSTALLATION DETAILS AND WARNINGS PRIOR TO FINAL INSTALLATION IF YOU HAVE QUESTIONS IMMEDIATELY CALL THE CUSTOMER SERVICE NUMBER LISTED ON PG 2 2 This product is classified as a temporary fabric covered shelter and is intended to protect what is stored in it from basic environmental elements including the effects of sun rain tree sap bird and animal excrement and light snow IT IS NOT DESIGNED TO HOLD THE LOAD FROM HIGH WINDS HEAVY SNOW OR ICE STORMS 3 Proper anchoring is the RESPONSIBILITY OF THE OWNER Any shelter that is not anchored securely and properly has the potential to blow away in high winds ShelterLogic cannot be held responsible for any shelter that blows away NOTE Your shelter s cover can be quickly removed and stored prior to severe weather conditions If strong winds or severe weather is forecast in your area we recommend that you remove the cover CARE amp CLEANING A tight cover will ensure longer life and performance Inspect and retighten the ratchet tie downs monthly as needed Always maintain a tight cover Loose fabric can accelerate deterioration of the cover Immediately remove any accumulated snow or ice from the roof structure with a broom mop or other soft sided instrument Do NOT use protect and shine or harsh or abrasive products to clean the fabric cover Mild soap and water is recommended to clean the fabric cover of your shelter Page 8
5. ly to remove the slack from the end panel Be careful not to pull the webbing through the other side of the panel Install the S hook from the ratchet into the leg of the shelter Fig 10D Insert the webbing into the spindle of the ratchet and pull tight Wind the ratchet enough so that the webbing overlaps itself Repeat the process on the other side of the panel Position the end panel so that it is centered on the building Tighten the ratchets alternating from one side to the other until the end panel is tight Repeat these steps on the other end of the building Fig 10C Page 5 STEP 11 INSTALLING THE COVER ON THE FRAME Fig 11A 11B 11C amp 11D 1 Lay the cover on the ground next to the frame with the inside of the cover the side with the pipe pockets facing down and the webbing on the front and rear of the corner of the building Position the cover so that it is centered on the frame front to back Fig 11A 2 Fold over the side closest to the frame so the pipe pocket is now accessible Insert a cover pipe at the first middle rib from the front and the first middle rib from the rear so that it is inserted in the pipe pocket on both ends of the pipe but the center of the pipe is exposed For long buildings it may be necessary to use additional pipes in the middle Fig 11B 3 Tie the rope on each of the exposed pipes and throw the other end of the rope over the frame Fig 11C 4 Move
6. nds Side Rail NOTE Connections that do not use a wind brace use a 4 1 8 bolt 800454 STEP 6 INSTALL WIND BRACES 11102 Fig 6 Take the wind brace and attach it between the end rib and the first middle rib as shown in Fig 6 Any attachments at the cross rails should be made on the very inside of the cross rail Wind Brace Fig 6 STEP 7 INSTALL TOP RAIL Fig 7 Place the first top rail over the pipe on the top end connector Fig 6 The same cross rail should lay on top of the first middle rib as with all of the middle ribs Secure the rails to the frame with the hardware indicated in Fig 7 The top rail attached to the last rib will be installed over the pipe on the top end connector Over all Middle Ribs D 11133 10133 Install the Top Rail N Page 4 STEP 8 SECURE BASE FEET Fig 8 Depending on the model you have purchased your base feet will either fit onto the outside of the leg pole or slide into the bottom of the leg pole After installing the base feet line up the holes in the leg to the holes in the feet and secure with the hardware indicated in Fig 8 N sen with A Bolt amp nut STEP 9 INSTALL AUGER ANCHORS Fig 9 Using a pipe or steel rod a car tire iron works also placed through the eyelet of the auger screw the anchor into the ground Start at the corners of the shelter and space the remaining anchors evenly along the length of the shelter Screw the anchor into the
7. rope diagonally from corner to corner 3 Measure from where the two ropes intersect each other to all 4 corners This measurement should be the same If they are not equal the stakes need to be lt a gt adjusted until the width length and inside measurements are correct Fig 1 11136 w STEP 2 ASSEMBLE END RIBS Fig 2 Assemble end ribs as shown in Fig 2 Securely fasten all of the joints with the hardware indicated Use 11131 5 16 x 2 3 4 Bolts End Rib Fig 2 STEP 3 ASSEMBLE MIDDLE RIBS 11135 Fig 3 Assemble all of the middle ribs as shown in Fig 3 Securely fasten all of the joints with the hardware indicated Use 11131 5 16 x 2 3 4 Bolts Middle Rib STEP 4 ASSEMBLE WIND BRACES Fig 3 Fig 4 Assemble all of the wind braces as shown in Fig 4 Securely fasten the joints with the hardware indicated 11093 Fig 4 L lt E SSS 11095 690 11102 STEP 5 INSTALL SIDE RAILS AND SHELTERLOCK STABILIZER BLOCKS Fig 5 With help move the first end rib into the desired staked area Place the ShelterLock on the upright as shown in Fig 5 From the outside amp A e of the rib insert the bolt through the upright and then through the ShelterLock Place the plain end of the side rail over the bolt and nest it into the ShelterLock Install the nut onto the bolt and tighten Repeat these steps for the opposite side and all of the remaining ribs The side rails for the last rib will have two plain e
8. to the other side of the frame and pull the cover over the frame with the rope This may require two or more people Fig 11D STEP 12 SECURE YOUR COVER Outside Corner View Fig 12A 12B 13 amp 14 Install the S hook from the ratchet assembly into the legs of the shelter Pull the webbing carefully to remove the slack from the cover Be careful not to pull the webbing through the opposite side of the cover Insert the webbing through the spindle of the ratchet and pull tight Wind the ratchet until the webbing overlaps itself Repeat these steps on the opposite side Repeat this on the back side of the shelter When all of the corners are secured move the cover front to back so that it is centered When the cover is centered tighten all of the ratchets Do this in an X pattern to be sure it is tightened evenly Fig 12A amp 12B When the cover is tight from end to end install the 45 cover rails Insert the cover rails into the pockets of the cover Clamp the rails to the ribs using the 3 way and 4 way clamps as shown in Fig 13 amp 14 Check that the rails are evenly spaced above the cates RT ground on both sides Push down on the connectors Fig 12A one ata time to tighten the cover Tighten the bolts to the cover in place and tight on the frame CORRECT COVER TIGHTENING TIP Check and tighten Ratchets and Cross ShelterLogier N y D Rails monthly to ensure the cover is tight
Download Pdf Manuals
Related Search