Home

Chamberlain HD950WF Instructions / Assembly

1. Charge the Battery The battery charges while the garage door opener is plugged into an electrical outlet The battery requires 24 hours to fully charge A fully charged battery supplies 12Vdc to the garage door opener for one to two days of normal operation during an electrical power outage After the electrical power has been restored the battery will recharge within 24 hours The battery will last approximately 1 to 2 years with normal usage To obtain maximum battery life and prevent damage disconnect the battery when the garage door opener is unplugged for an extended period of time such as a summer or winter home MyQ Smartphone Control Get Connected and control your garage door opener with the MyQ App You will need A smartphone or tablet Broadband Internet connection A strong Wi Fi signal in the garage see page 2 Password for your home network MyQ serial number located on the garage door opener 1 ACTIVATE WI FI LEARN MODE Press and release the yellow LEARN button on the garage door opener 3 times The garage door opener will beep once and a blue light will flash You have 20 minutes to complete the connection process 2 CONNECT TO THE MyQ Wi Fi NETWORK On your mobile device go to Settings gt Wi Fi and select the network with the MyQ prefix 31 3 CONNECT THE GARAGE DOOR OPENER TO YOUR HOME WI FI NETWORK Launch the web brow
2. Header Wall 2x4 Support Finished Ceiling Optional Placement of Door Bracket Vertical Centerline of Garage Door Metal Door Self Threading Screw 1 4 14x5 8 Wood Door Door Top of Door Bracket Bracket Inside Garage Top Edge of Door Optional Placement For a door with no exposed framing or for the optional installation use lag screws 5 16 x1 1 2 not provided to fasten the door bracket Hardware not provided Top of Door Inside Garage Top Edge of Door Optional Placement Hardware not provided Installation STEP 9 Connect the door arm to the trolley Installation will vary according to the garage door type Follow the instructions which apply to your door OPTION A SECTIONAL DOORS IMPORTANT The groove on the straight door arm MUST face away from the curved door arm 1 Close the door Disconnect the trolley by pulling the emergency release handle 2 Attach the straight door arm to the outer trolley using the clevis pin Secure with the ring fastener 3 Attach the curved door arm to the door bracket using the clevis pin Secure with the ring fastener 4 Bring arm sections together Find two pairs of holes that line up and join sections Select holes as far apart as possible to increase door arm rigidity and attach using the bolts nuts and lock washers 5 Pull the emergency release handle toward the garage door opene
3. CAUTION To prevent INJURY from pinching keep hands and fingers away from the joints while assembling the an Pee rail SIDES OF Outer Trolley U BRACKET U Bracket _ To garage door opener TO MOTOR UNIT To avoid installation difficulties do not run the garage door opener until instructed to do so The front rail has a cut out window at the door end The rail tab MUST be on top of the rail when assembled 1 Remove the straight door arm and hanging bracket packaged inside the front rail and set aside for Installation Step 5 and 9 NOTE To prevent INJURY while unpacking the rail carefully remove the straight door arm stored within the rail section 2 Align the rail sections on a flat surface as shown and slide the tapered ends into the larger ones Tabs along the side will lock into place 3 Place the motor unit on packing material to protect the cover and rest the back end of the rail on top For convenience puta support under the front end of the rail 4 Asa temporary stop insert a screwdriver into the hole in the second rail section from the motor unit as shown 5 Check to be sure there are 4 plastic wear pads inside the inner trolley If they became loose during shipping check all packing material Snap them back into position as shown Slide the trolley assembly toward the screwdriver as shown Slide the rail onto the U bracket until it reaches all the stops on the top a
4. Attach the warning labels HARDWARE 1 Attach the entrapment warning label on the wall near the door control with tacks or staples 2 Attach the manual release safety reverse test label in a visible location on the inside of the garage door Insulated Staple Not Shown 1 Run the white and red white wire from the door control to the garage door opener Attach the wire to the wall and ceiling with the staple not applicable for gang box or pre wired installations Do not pierce the wire with the staple as this may cause a short or an open circuit 2 Strip 7 16 inch 11 mm of insulation from the end of the wire near the garage door opener 3 Connect the wire to the red and white terminals on the garage door opener If your garage is pre wired make sure you use the same wires that are connected to the door control To insert or release wires from the terminal push in the tab with screwdriver tip 7 16 11 mm le gt 20 Installation STEP 13 Install the Protector System HARDWARE Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing The safety reversing sensors can be attached to the door track the wall or the floor The sensors should be no more than 6 inches 15 cm above the floor Ifthe door track will not support the sensor bracketa wall installation is recommended Choose one of the following installations sensor To prevent SERIOUS INJURY or DEATH from
5. Chamberlain openers from 1993 present MyQ compatible Keychain Remote Control Works with ALL Chamberlain openers from 1993 present MyQ compatible With key ring MyQ Internet Gateway Offers longer range wireless signal than standard Wi Fi Plugs into your home router as an optional way to provide MyQ Smartphone Control for your garage door opener and MyQ light controls 41A6357 1 Standby Power System Battery Provides backup power to the garage door opener Garage Door Monitor Monitor open closed status for up to 4 MyQ compatible garage door openers or gate operators and close them from anywhere in the home Warranty STOP This garage door opener WILL NOT work until the safety reversing sensors are properly installed and aligned Contact Information For installation and service information please visit www chamberlain com parts and support If you are ordering a repair part please have the following information part number part name and model number Address repair parts orders to The Chamberlain Group Inc 6050 S Country Club Road Tucson AZ 85706 Register your new garage door opener at www prodregister com chamberlain CHAMBERLAIN LIMITED WARRANTY The Chamberlain Group Inc Seller warrants to the first retail purchaser of this product for the residence in which this product is originally installed that it is free from defects in materials and or workmanship for
6. Close TTC feature the MyQ Smartphone Control and any other MyQ devices are to be used ONLY with sectional doors Check the Door 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH ALWAYS call a trained door systems technician if garage door binds sticks or is out of balance An unbalanced garage door may NOT reverse when required NEVER try to loosen move or adjust garage door door springs cables pulleys brackets or their hardware ALL of which are under EXTREME tension Disable ALL locks and remove ALL ropes connected to garage door BEFORE installation and operating garage door opener to avoid entanglement DO NOT install on a one piece door if using devices or features providing unattended close Unattended devices and features are to be used ONLY with sectional doors CAUTION To prevent damage to garage door and opener e ALWAYS disable locks BEFORE installing and operating the opener e ONLY operate garage door opener at 120 V 60 Hz to avoid malfunction and damage Before you begin 1 Disable locks and remove any ropes connected to the garage door 2 _Liftthe door halfway up Release the door If balanced it should stay in place supported entirely by its springs 3 Raise and lower the door to check for binding or sticking If your door Torsion Extension binds sticks or is out of balance call a trained door systems Spring OR spring technician Pp ot 4 Check the seal on the bottom of the door Any
7. Secure with the ring fastener 5 Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal HARDWARE Clevis Pin 5 16 x1 1 4 Clevis Pin 5 16 x1 Hex Bolt 5 16 18x7 8 Ring Fastener Fastener Raa d Nut 5 16 18 d Lock Washer 5 16 18 amp Clevis Pin 5 16 x1 Ring Fastener Lock Washer 5 16 18 Nut 5 16 18 Ring Fastener Nut 5 16 18 Lock Washer 5 16 18 amp e ooooo0oo009Q900o0 g Clovis Pin Ostet 1 4 Hex Bolt 5 16 18x7 8 Clevis Pin 5 16 x1 18 Installation STEP 10 Install the door control To prevent possible SERIOUS INJURY or DEATH from electrocution e Be sure power is NOT connected BEFORE installing door control e Connect ONLY to 12 VOLT low voltage wires To prevent possible SERIOUS INJURY or DEATH from a closing garage door e Install door control within sight of garage door out of reach of children ata minimum height of 5 feet 1 5 m and away from ALL moving parts of door NEVER permit children to operate or play with door control push buttons or remote control transmitters Activate door ONLY when it can be seen clearly is properly adjusted and there are no obstructions to door travel ALWAYS keep garage door in sight until completely closed NEVER permit anyone to cross path of closing garage door INTRODUCTION Older Chamberlain door controls and third party products are not compatible Install the door control wit
8. a specific period of time as defined below the Warranty Period The warranty period commences from the date of purchase WARRANTY PERIOD Parts Motor Accessories Belt Battery Backup 5 Years Lifetime 1 year Lifetime 1 year The proper operation of this product is dependent on your compliance with the instructions regarding installation operation and maintenance and testing Failure to comply strictly with those instructions will void this limited warranty in its entirety If during the limited warranty period this product appears to contain a defect covered by this limited warranty call 1 800 528 9131 toll free before dismantling this product You will be advised of disassembly and shipping instructions when you call Then send the product or component pre paid and insured as directed to our service center for warranty repair Please include a brief description of the problem and a dated proof of purchase receipt with any product returned for warranty repair Products returned to Seller for warranty repair which upon receipt by Seller are confirmed to be defective and covered by this limited warranty will be repaired or replaced at Seller s sole option at no cost to you and returned pre paid Defective parts will be repaired or replaced with new or factory rebuilt parts at Seller s sole option You are responsible for any costs incurred in removing and or reinstalling the product or any component ALL I
9. close Unattended devices and features are to be used ONLY with sectional doors 16 SAVE THESE INSTRUCTIONS Operation Using your Garage Door Opener To Open the Door Manually e The garage door opener can be activated with a wall mounted door control remote control wireless keyless entry MyQ Smartphone Control app or MyQ Garage Door Monitor When the A W AR N l NG door is closed and the garage door opener is activated the door will open Ifthe door senses an obstruction or is interrupted while opening the door will stop When the door is in any position other than closed and the garage door opener is activated the door will close Ifthe garage door opener senses an obstruction while closing the door will reverse If the obstruction interrupts the sensor beam the garage door opener lights will blink 10 times If the door is fully open and the safety reversing sensors are notinstalled or are misaligned the door will not close from a remote control TTC or the MyQ Smartphone Control app However you can close the door by holding the button on the door control or the ENTER button on the keyless entry until the door is fully To prevent possible SERIOUS INJURY or DEATH from a falling garage door e fpossible use emergency release handle to disengage trolley ONLY when garage door is CLOSED Weak or broken springs or unbalanced door could result in an open door falling rapidly and or unexpectedly NEVER use emergency release handle u
10. door opener lights turn on the sensor LEDs will light The garage door opener will not go into the sleep mode until the garage door opener has completed 5 cycles upon power up When installing the safety reversing sensors check the following e Sensors are installed inside the garage one on either side of the door e Sensors are facing each other with the lenses aligned and the receiving sensor lens does not receive direct sunlight e Sensors are no more than 6 inches 15 cm above the floor and the light beam is unobstructed No more than 6 inches 15 cm Carriage Bolt 1 4 20x1 2 Safety Reversing Sensor Invisible Light Beam 6 15 cm max above floor Protection Area z E TIN Facing the door from inside the garage sat 5 21 Installation STEP 13 Install the Protector System continued OPTION B WALL INSTALLATION lf additional clearance is needed an extension bracket not provided or wood blocks can be used Make sure each bracket has the same amount of clearance so they will align correctly 1 Position the sensor bracket against the wall with the curved arms facing the door Make sure there is enough clearance for the beam to be unobstructed Mark holes 2 Drill 3 16 inch pilot holes for each sensor bracket and attach the sensor brackets to the wall using lag screws not provided 3 Slide the carriage bolt into the slot on each sensor 4 Insertthe bolt through t
11. opener to the hanging brackets with the hex bolts lock washers and nuts 6 Remove the 2x4 and manually close the door If the door hits the rail raise the header bracket 3 Ceiling 2 2 Lag Screw Lag Screw 5 16 5 16 9x1 5 8 9x1 5 8 4 5 Hex Bolt 5 16 18x7 8 Lock Washer not 5 16 18 provided Nut 5 16 18 Installation STEP 6 Install the light bulbs STEP 7 Attach the emergency release rope and handle To prevent possible OVERHEATING of the end panel or light socket To prevent possible SERIOUS INJURY or DEATH from a falling garage door e Use ONLY A19 incandescent 100W maximum or compact fluorescent 26W maximum light e lf possible use emergency release handle to disengage trolley ONLY when garage door is bulbs CLOSED Weak or broken springs or unbalanced door could result in an open door falling DO NOT use incandescent bulbs larger than 100W rapidly and or unexpectedly DO NOT use compact fluorescent light bulbs larger than 26W 100W equivalent NEVER use emergency release handle unless garage doorway is clear of persons and DO NOT use halogen bulbs obstructions DO NOT use short neck or specialty light bulbs NEVER use handle to pull door open or closed If rope knot becomes untied you could fall 1 Pull on the top sides of the light lens and rotate the light lens down 1 Insertone end of the emergency release rope through the handle Make sure that NOTICE is 2 Insert an Al
12. the menu button is pressed and then it will display the menu options If there is a problem with the garage doors opener the screen will display an error code diagnostic code see page 38 The features on the door control can be programmed through a series of menus on the screen Use the navigation buttons to scroll through the menus and make selections MENU OPTIONS CLOCK SETUP TTC OFF LOCK DISABLED TEMPERATURE LANGUAGE ENGLISH LIGHT SETTINGS CONTRAST ADJUST 50 EXT LY PROGRAM S EXT L gt C C IC ILI COC CO CO CLOCK SETUP Set the time choose 12 or 24 hour clock and show hide clock TEMPERATURE Display the temperature in Fahrenheit or Celsius and show hide the temperature LANGUAGE Select English Spanish or French CONTRAST ADJUST Adjust the screen contrast LIGHT SETTINGS To change the amount of time the lights stay on 1 Select LIGHT SETTINGS from the menu 2 Select LIGHT TIME 3 Select the time interval To turn the Light Feature on or off Factory default is On 1 Select LIGHT SETTINGS from the menu 2 Select AUTOMATIC LIGHTS 3 Select ENTRY SENSOR To turn the motion sensor on or off 1 Select LIGHT SETTINGS from the menu 2 Select AUTOMATIC LIGHTS 3 Select MOTION SENSOR LOCK Prevents the garage door opener from being activated by remote controls while still allowing activation from the door control and keyless entry To turn the LOCK feature ON or OFF 1 Se
13. to operate your garage door Keyless Entry Enter a 4 digit personal identification number PIN of your choice on the keyless entry keypad Then press the ENTER button The garage door opener lights will flash or two clicks will be heard when the code has been programmed Repeat the steps for programming additional remote controls or keyless entry devices If programming is unsuccessful repeat the steps using the learn button on the garage door opener 2 Press MES to continue CLOCK SETUP TTC OFF LOCK DISABLED PROGRAM ext L gt COC 3 Press ES to continue REMOTE 7 MYQ DEVICE LIGHT TO REMOTE KEYPAD x e be DOOR WA 3 dC Operation To Erase the Memory ERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES 1 Press and hold the LEARN button on garage door opener until the learn LED goes out approximately 6 seconds All remote control and keyless entry codes are now erased Reprogram any accessory you wish to use ERASE ALL REMOTE CONTROLS KEYLESS ENTRIES AND MyQ DEVICES FROM GARAGE DOOR OPENER 1 Press and hold the LEARN button on garage door opener until the learn LED goes out approximately 6 seconds 2 Immediately press and hold the LEARN button again until the learn LED goes out All codes are now erased Reprogram any accessory you wish to use ERASE THE CONNECTION FROM GARAGE DOOR OPENER TO HOME Wi Fi NETWORK 1 Press and hold the black adjustment button on
14. trolley can remain disconnected until instructed Ring Fastener Clevis Pin 5 16 x1 1 2 Connected Disconnected One piece door without tracks All other door types 12 Installation STEP 5 Hang the garage door opener 4 amp WARNING To avoid possible SERIOUS INJURY from a falling garage door opener fasten it SECURELY to structural supports of the garage Concrete anchors MUST be used if installing ANY brackets into masonry Hanging the garage door opener will vary depending on your garage Below are three example installations Your installation may be different For ALL installations the garage door opener MUST be connected to structural supports The instructions illustrate one of the examples below Unfinished Finished _ L fi cS Ceiling Ceiling HARDWARE Lock Washer 5 16 18 Lag Screw 5 16 9x1 5 8 Nut 5 16 18 Hex Bolt 5 16 18x7 8 13 1 On finished ceilings use the lag screws to attach a support bracket not provided to the structural supports before installing the garage door opener 2 Make sure the garage door opener is aligned with the header bracket Measure the distance from each side of the garage door opener to the support bracket 3 Cutboth pieces of the hanging bracket to required lengths 4 Attach the end of each hanging bracket to the support bracket with appropriate hardware not provided 5 Attach the garage door
15. 39 AGGOSSONIGS oara aanne 40 Warranty o anene EEEE ERE 41 Repair Parts exces servos 42 43 www chamberlain com www mychamberlain com The Chamberlain Group Inc 845 Larch Avenue Elmhurst Illinois 60126 1196 Preparation Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided itis installed operated maintained and tested in strict accordance with the instructions and warnings contained in this manual When you see these Safety Symbols and Signal Words on the following pages they will alert you to the possibility of serious injury or deathif you do not comply with the warnings that accompany them The hazard may come from something mechanical or from electric shock Read the warnings carefully 4 amp WARNING Mechanical A WARNING Electrical When you see this Signal Word on the following pages it will alert you to the possibility of damage to your garage door and or the garage door opener if you do not comply with the cautionary statements that accompany it Read them carefully CAUTION Unattended Operation The Timer to Close TTC feature the MyQ Smartphone Control app and MyQ Garage Door and Gate Monitor are examples of unattended close and are to be used ONLY with sectional doors Any device or feature that allows the door to close without being in the line of sight of the door is considered unattended close The Timer to
16. 6 Insert the trolley threaded shaft through the hole in the trolley HARDWARE Threaded Shaft with Spring Trolley Nut i SOG Figure 1 Trolley Connector Retaining Slot Figure 2 Sprocket Assembly STEP 5 Tighten the belt 1 By hand thread the spring trolley nut on the threaded shaft until itis finger tight against the trolley Do not use any tools Remove the screwdriver 2 Inserta flathead screwdriver tip into one of the nut ring slots and brace it firmly against the trolley 3 Tighten the spring trolley nut with an adjustable wrench or a 7 16 open end wrench abouta quarter turn until the spring releases and snaps the nut ring against the trolley This sets the spring to optimum belt tension Nut Ring Slot Spring N Trolley Nut Z N Oy Nut Ring Nut Ring BEFORE AFTER 1 1 1 4 2 5 cm 3 18 cm STEP 6 Install the sprocket cover 4 amp WARNING To avoid possible SERIOUS INJURY to finger from moving garage door opener e ALWAYS keep hand clear of sprocket while operating opener e Securely attach sprocket cover BEFORE operating 1 Position the sprocket cover over the sprocket as shown and fasten to the mounting plate with 8x3 8 hex screws provided You have now finished assembling your garage door opener Please read the following warnings before proceeding to the installation section HARDWARE Hex Screw 8x3 8 Packed with th
17. 9 neandescent 100W maximum or compact fluorescent 26W 100W equivalent right side up Tie a knotat least 1 inch 2 5 cm from the end of the emergency release rope light bulb into the light socket 2 Insert the other end of the emergency release rope through the hole in the trolley release arm 3 Rotate the lens up to close Mount the emergency release within reach but atleast 6 feet 1 83 m above floor avoiding NOTE Do notuse halogen shortneck or specialty light bulbs as these may overheat the end panel or contact with vehicles to prevent accidental release and secure with a knot light socket Do not use LED bulbs as they may reduce the range or performance of your remote controls NOTE Ifitis necessary to cut the emergency release rope seal the cut end with a match or lighter to prevent unraveling Ensure the emergency release rope and handle are above the top ofall vehicles to avoid entanglement 14 Installation STEP 8 Install the door bracket CAUTION Fiberglass aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit Failure to reinforce the top section as required according to the door manufacturer may void the door warranty A horizontal and vertical reinforcement is needed for lightweight garage doors fiberglass aluminum steel doors with gl
18. CHAMBERLAIN 1 1 4 hps Belt Drive Garage Door Opener with MyQ Smartphone Control and Battery Backup Model HD9SOWF FOR RESIDENTIAL USE ONLY Battery Backup WORKS EVEN WHEN THE POWER IS OUT F i CERTIFIED my Write down the MyQ serial number located on the garage door opener Horsepower similar hps designates that this garage door opener system meets Chamberlain s pulling force specification for a 1 1 4 horsepower garage door opener W Please read this manual and the enclosed safety materials carefully E Fasten the manual near the garage door after installation E The door WILL NOT CLOSE unless the Protector System is connected and properly aligned Periodic checks of the garage door opener are required to ensure safe operation E The model number label is located on the left side panel of your garage door opener E This garage door opener is compatible with MyQ and Security 2 0 accessories DO NOT install on a one piece door if using devices or features providing unattended close Unattended devices and features are to be used ONLY with sectional doors CONTENTS Preparation seres eanan 1 4 Assembly eera no nearen 5 8 Installations e oee o 9 26 Adjustments 27 29 Battery Backup 30 MyQ Smartphone Control Get Connected 31 Operations st ects certs 32 36 Maintenance 0225 6 37 Troubleshooting 38
19. Highest ceiling installation s Highest Point of g Point of Travel Travel Hardware Pivot 10 Installation STEP 2 Install the header bracket OPTION B CEILING INSTALLATION You can attach the header bracket either to the wall above the garage door or to the ceiling Follow the 1 Extend the vertical centerline onto the ceiling as shown instructions which will work best for your particular requirements Do not install the header bracket over 2 Center the bracket on the vertical mark no more than 6 15 cm from the wall Make sure the drywall If installing into masonry use concrete anchors not provided arrow is pointing away from the wall The bracket can be mounted flush against the ceiling when HARDWARE clearance is minimal 3 Mark the side holes Drill 3 16 pilot holes and fasten bracket securely to a structural support with the hardware provided Lag Screw 5 16 9x1 5 8 Header Bracket Ceiling Mounting OPTION A WALL INSTALLATION 1 Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown with the arrow pointing toward the ceiling 2 Mark the vertical set of bracket holes Drill 3 16 pilot holes and fasten the bracket securely to a structural support with the hardware provided 6 15 cm Vertical Centerline of Garage Door Wall Mount Header Wall Vertical Centerline of Garage Door Lag Screw 5 16 9
20. IABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT Some states and provinces do not allow the exclusion or limitation of consequential incidental or special damages so the above limitation or exclusion may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state and province to province Repair Parts Rail Assembly Parts Installation Parts Description Part Number Curved Door Arm 178B35 Door Bracket with Clevis 41A5047 1 Pin and Fastener Description Part Number Belt 41A5250 Pulley 144054 Master Link 4A1008 Rail 41A5665 Trolley Assembly 4105141 2 U Bracket 12D598 1 Not Shown Wear Pads 183A163 Hardware Bag 041A7920 2 Emergency Release Rope 41A2828 and Handle Header Bracket with 41A5047 2 Clevis Pin and Fastener 4 4 Remote Control 29B137 Visor Clip Safety Sensor Bracket 041A5266 3 Safety Sensor Kit 41A5034 Receiving and sending sensors with wire ay Straight Door Arm 178B34 9 White and Red White Wire 41B4494 1 10 3V CR2032 Lithium 10A20 a Accessories Battery 11 Hanging Brackets 12B776 Description Part Number 1 Smart Control Panel 41A7305 1 2 Remote Control 953ESTD Not Shown amp Owner s Manual 114A4763 42 Repai
21. MPLIED WARRANTIES FOR THE PRODUCT INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED COMPONENT S AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD Some States and Provinces do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you THIS LIMITED WARRANTY DOES NOT COVER NON DEFECT DAMAGE DAMAGE CAUSED BY IMPROPER INSTALLATION OPERATION OR CARE INCLUDING BUT NOT LIMITED TO ABUSE MISUSE FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT REPLACEMENT OF CONSUMABLE ITEMS E G BATTERIES IN REMOTE CONTROL TRANSMITTERS AND LIGHT BULBS OR UNITS INSTALLED FOR NON RESIDENTIAL USE THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH OR RELATING TO THE GARAGE DOOR OR GARAGE DOOR HARDWARE INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS DOOR ROLLERS DOOR ALIGNMENT OR HINGES THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE OR INABILITY TO USE THIS PRODUCT IN NO EVENT SHALL SELLER S LIABILITY FOR BREACH OF WARRANTY BREACH OF CONTRACT NEGLIGENCE OR STRICT L
22. NOTE If anything interferes with the door s upward travel it will stop Ifanything interferes with the door s downward travel it will reverse One Piece Doors Only When setting the UP travel for a one piece door ensure that the door does not slant backwards when fully open UP If the door is slanted backwards this will cause unnecessary bucking and or jerking when the door is opening or closing INCORRECT Programming Buttons The programming buttons are located on the left side panel of the garage door opener and are used to program the travel While programming the UP and DOWN buttons can be used to move the door as needed PROGRAMMING BUTTONS UP Button Adjustment Button DOWN Button To watch a short instructional video on how to program the travel on your new garage door opener use your smartphone to read the QR Code 27 Adjustments STEP 1 Program the Travel O E PROGRAMMING BUTTONS 4 amp WARNING Without a properly installed safety reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door i DOWN Button e Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system e After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 3 8 cm high object or 2x4 laid flat on floor While programming the UP and DOWN buttons can be
23. OLUTION Communication error to travel module Check travel module connections replace travel module if necessary Safety sensors are misaligned or were momentarily obstructed Realign both sensors to ensure both LEDs are steady and not flickering Make sure nothing is hanging or mounted on the door that would interrupt the sensor s path while closing My vehicle s Homelink is not programming to my garage door opener Depending on the make model and year of your vehicle an external adapter may be required Visit www homelink com for additional information Wi Fi troubleshooting If your black adjustment button is not solid green go to wifihelp chamberlain com Green battery status LED All systems are normal e A solid green LED light indicates the battery is fully charged A flashing green LED indicates the battery is being charged Orange battery status LED The garage door opener has lost power and is in battery backup mode e A solid orange LED with beep sounding approximately every 2 seconds indicates the garage door opener is operating on battery power e A flashing orange LED with beep sounding every 30 seconds indicates the battery is low Red battery status LED The garage door opener s 12V battery needs to be replaced e A solid red LED with beep sounding every 30 seconds indicates the 12V battery will no longer hold a charge and needs to be replaced Please call for replacement battery to allow your system to operate during a
24. Pre installed Safety reversing a sensor wires Not Provided Safety reversing Pre installed wires sensor wires White White Black Yellow for example Purple for example Purple Yellow for for example example To insert or remove the wires from the terminal push in the tab with a screwdriver tip Installation STEP 15 Connect power To prevent possible SERIOUS INJURY or DEATH from electrocution or fire Be sure power is NOT connected to the opener and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes NEVER use an extension cord 2 wire adapter or change plug in ANY way to make it fit outlet Be sure the opener is grounded To avoid installation difficulties do not run the opener at this time To reduce the risk of electric shock your garage door opener has a grounding type plug with a third grounding pin This plug will only fit into a grounding type outlet If the plug doesn t fit into the outlet you have contact a qualified electrician to install the proper outlet 25 THERE ARE TWO OPTIONS FOR CONNECTING POWER OPTION A TYPICAL WIRING 1 Plugin the garage door opener into a grounded outlet 2 DO NOT run garage door opener at this time OPTION B PERMANENT WIRING If permanent wiring is required by your local code refer to the following p
25. ass panel etc not provided A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports A vertical reinforcement brace should cover the height of the top panel Contact the garage door manufacturer or installing dealer for opener reinforcement instructions or reinforcement kit NOTE Many door reinforcement kits provide for direct attachment of the clevis pin and door arm In this case you will notneed the door bracket proceed to the next step HARDWARE Self Threading Screw 1 4 14x5 8 OPTION A SECTIONAL DOORS 1 Center the door bracket on the previously marked vertical centerline used for the header bracket installation Note correct UP placement as stamped inside the bracket 2 Position the top edge of the bracket 2 4 5 10 cm below the top edge of the door OR directly below any structural support across the top of the door 3 Mark drill holes and install as follows depending on your door s construction Metal or light weight doors using a vertical angle iron brace between the door panel support and the door bracket e Drill 3 16 fastening holes Secure the door bracket using the two 1 4 14x5 8 self threading screws Figure 1 e Alternately use two 5 16 18x2 bolts lock washers and nuts not provided Figure 2 Metal insulated or light weight factory reinforced doors e Drill 3 16 fastening holes Secure the door bracket using the self thr
26. au moins 20 cm 8 po entre celui ciet utiisateurou toute personne Troubleshooting 38 Diagnostic Chart Your garage door opener is programmed with self diagnostic capabilities The UP and DOWN arrows on the garage door opener flash the diagnostic codes DIAGNOSTIC CODE SYMPTOM SOLUTION Up Arrow Down Arrow Flash es Flash es 4 The garage door opener will not close and the light bulbs flash ier Praa are notinstalled connected or wires may be cut Inspect sensor wires for a disconnected 4 2 The garage door opener will not close and the light bulbs flash There isa short or reversed wire for the safety sensors Inspect safety sensor wire atall staple and connection points replace wire or correct as needed The wires for the door control are shorted or the door control is faulty Inspect door control wires at all 1 3 The door control will not function 5 i staple and connection points replace wire or correct as needed Safety sensors are misaligned or were momentarily obstructed Realign both sensors to ensure both 1 4 The garage door opener will not close and the lightbulbs flash LEDs are steady and not flickering Make sure nothing is hanging or mounted on the door that would interrupt the sensor s path while closing Manually open and close the door Check for binding or obstructions such as a broken spring or door 1 5 Door moves 6 8 stops or reverses ock correct as needed Check wiring connections at travel module and a
27. closing garage door e Correctly connect and align the safety reversing sensor This required safety device MUST NOT be disabled e Install the safety reversing sensor so beam is NO HIGHER than 6 15 cm above garage floor OPTION A DOOR TRACK INSTALLATION IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSORS 1 Slide the curved arms of the sensor bracket around the edge of the door track Snap into place The safety reversing sensors must be connected and aligned correctly before the garage door so that the sensor bracketis flush against the track opener will move in the down direction 2 Slide the carriage bolt into the slot on each sensor The sending sensor with an amber LED transmits an invisible light beam to the receiving sensor with a 3 _Insertthe bolt through the hole in the sensor bracket and attach with the wing nut The lenses on green LED lf an obstruction breaks the light beam while the door is closing the door will stop and both sensors should point toward each other Make sure the lens is not obstructed by the sensor reverse to the full open position and the garage door opener lights will flash 10 times bracket NOTE For energy efficiency the garage door opener will enter sleep mode when the door is fully closed The sleep mode shuts the garage door opener down until activated The sleep mode is sequenced with the garage door opener light bulb as the light bulb turns off the sensor LEDs will turn off and whenever the garage
28. e sprocket cover 1s Hex Screw 8x3 8 Installation IMPORTANT INSTALLATION INSTRUCTIONS A amp WARNING To reduce the risk of SEVERE INJURY or DEATH READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS Install garage door opener ONLY on properly balanced and lubricated garage door An improperly balanced door may NOT reverse when required and could resultin SEVERE INJURY or DEATH ALL repairs to cables spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid entanglement Install garage door opener 7 feet 2 13 m or more above floor Mount the emergency release within reach but at least 6 feet 1 83 m above the floor and avoiding contact with vehicles to avoid accidental release NEVER connect garage door opener to power source until instructed to do so NEVER wear watches rings or loose clothing while installing or servicing opener They could be caughtin garage door or opener mechanisms 9 Install wall mounted garage door control e within sight of the garage door e outofreach of children at minimum height of 5 feet 1 5 m e away from ALL moving parts of the door Place entrapment warning label on wall nextto garage door control Place manual release safety reverse test label in plain view on inside of garage door Upon completion of installat
29. e Operating on battery power or the 12 Vdc battery needs to be replaced see page 30 e Garage door opener has been activated through a device or feature such as Timer to Close or garage door monitor see page 33 My remote control will not activate the garage door e Verify the lock feature is not activated on the door control e Reprogram the remote control e Ifthe remote control will still not activate the door check the diagnostic codes to ensure the garage door opener is working properly My door will not close and the light bulbs blink on my motor unit The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction e Verify the safety sensors are properly installed aligned and free of any obstructions My garage door opener light s will not tum off when the door is open The garage door opener is equipped with a feature that turns the light on when the safety reversing sensors have been obstructed or when the motion sensor on the door control detects movement in the garage These features can be disabled using the door control see page 33 My neighbor s remote control opens my garage door Erase the memory from your garage door opener and reprogram the remote control s The LEDs on the door control blink Ifyou have a Smart Control Panel installed and the TTC is set to a custom time press the ON button on the Premium Motion Detecting Control Panel to set the time properly S
30. eading screws Figure 3 Wood Doors e Use top and bottom or side to side door bracket holes Drill 5 16 holes through the door and secure bracket with 5 16 18x2 carriage bolts lock washers and nuts not provided Figure 4 NOTE The 14 14x5 8 self threading screws are not intended for use on wood doors FIGURE 1 Vertical FIGURE 2 Vertical Reinforcement Reinforcement Vertical Centerline of Garage Door Vertical Centerline of Garage Door Door Bracket Door Bracket D Y Hardware Self Threading Screw not provided 1 4 14x5 8 gt FIGURE 4 Inside Edge of Door or Vertical Reinforcement Board Centerline Hardware of Garage not provided Door UP Self Threading Screw Vertical Centerline of 1 4 14x5 8 Garage Door D Installation STEP 8 Install the door bracket continued OPTION B ONE PIECE DOORS 1 Center the door bracket on the top of the door in line with the header bracket as shown 2 Mark either the left and right or the top and bottom holes Metal Doors e Drill 3 16 pilot holes and fasten the bracket with the self threading screws provided Wood Doors e Drill 5 16 holes and use 5 16 18x2 carriage bolts lock washers and nuts not provided or 5 16 x1 1 2 lag screws not provided depending on your installation needs NOTE The door bracket may be installed on the top edge of the door if required for your installation Refer to the dotted line optional placement drawing 16
31. elease handle to disengage trolley ONLY when garage door is CLOSED Use caution when using this release with the door open Weak or broken springs or unbalanced door could resultin an open door falling rapidly and or unexpectedly and increasing the risk of SEVERE INJURY or DEATH NEVER use emergency release handle unless garage doorway is clear of persons and obstructions NEVER use handle to pull garage door open or closed If rope knot becomes untied you could fall 32 After ANY adjustments are made the safety reversal system MUST be tested Safety reversal system MUST be tested every month Garage door MUST reverse on contact with 1 1 2 3 8 cm high object or a 2x4 laid flat on the floor Failure to adjustthe garage door opener properly increases the risk of SEVERE INJURY or DEATH ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED see page 1 An improperly balanced door may NOT reverse when required and could resultin SEVERE INJURY or DEATH ALL repairs to cables spring assemblies and other hardware ALL of which are under EXTREME tension MUST be made by a trained door systems technician ALWAYS disconnect electric and battery power to garage door opener BEFORE making ANY repairs or removing covers This operator system is equipped with an unattended operation feature The door could move unexpectedly NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR DO NOT install on a one piece door if using devices or features providing unattended
32. ey into the window as shown 4 Insert the idler bolt from the top through the rail and pulley Tighten with a 3 8 lock washer and nut underneath the rail until the lock washer is compressed 5 Rotate the pulley to be sure it spins freely 6 Locate the rail tab The rail tab is near the idler pulley on the front rail section Use a flathead screwdriver and lift the rail tab until the tab is vertical 90 HARDWARE Bolt Lock Washer 3 8 Nut 3 8 CORRECT INCORRECT Ss Grease Inside Pulley Rail Tab Rail Lock Washer 3 8 Idler Pulley Nut 3 8 Trolley Connector Assembly STEP 4 Install the belt 1 Pull the belt around the idler pulley and toward the trolley The ribbed side must contact the pulley 2 Hook the trolley connector into the retaining slot on the trolley as shown Figure 1 3 With the trolley against the screwdriver dispense the remainder of the belt along the rail length toward the motor unit and around the sprocket Figure 2 The sprocket teeth must engage the belt 4 Check to make sure the beltis not twisted Connect the trolley threaded shaft with the master link Figure 3 e Push pins of master link bar through holes in end of belt and trolley threaded shaft e Push master link cap over pins and past pin notches e Slide the closed end of the clip on spring over one of the pins Push the open end of the clip on spring onto the other pin 5 Remove the spring trolley nut from the threaded shaft
33. gap between the floor and the bottom of the door must not exceed 1 4 inch 6 mm Otherwise the safety reversal system may not work properly 5 The opener should be installed above the center of the door If there is a torsion spring or center bearing plate in the way of the header bracket it may be installed within 4 feet 1 2 m to the left or right of the door center See page 10 Preparation Test the Wi Fi Signal Strength in your garage You will need a router with Wi Fi and a smartphone or other mobile device Make sure your mobile device is connected to your Wi Fi network Hold your mobile device in the place where your garage door opener will be installed and check the Wi Fi signal strength Check Signal Strength If you see o Wi Fi signal is strong You re all set Install your new garage door opener Wi Fi signal is weak The garage door opener will ikely connect to your Wi Fi network If not try one of the options below No Wi Fi signal Try one of the following e Move your router closer to the garage door opener to minimize interference from walls and other objects e Buy a Chamberlain MyQ Internet Gateway CIGBU see page 40 e Buy a Wi Fi range extender Visit wifihelp chamberlain com for more details See MyQ Smartphone Control page 31 to connect your garage door opener to your Wi Fi network Additional Items You May Need Survey your garage area to see if you will need any of the follo
34. ge door opener press the push bar until the garage door opener activates it may take up to 3 presses Test the door control by pressing the push bar each press of the push bar will activate the garage door opener Push Bar Screen Navigation Buttons Motion Sensor LIGHT Button PUSH BAR Press the push bar to open or close the door LIGHT BUTTON Press the LIGHT button to turn the garage door opener lights on or off When the lights are turned on they will stay on until the LIGHT button is pressed again or until the garage door opener is activated Once the garage door opener is activated the lights will turn off after the specified period of time the factory default is 4 1 2 minutes The LIGHT button will not control the lights when the door is in motion The Light Feature will turn on the light on the garage door opener when someone enters through the open garage door and the safety reversing sensor infrared beam is obstructed MOTION SENSOR The motion sensor automatically turns on the garage door opener lights when motion is detected The lights come on for the set period of time and then shut off If using the garage door opener light as a work light disable the motion sensor otherwise the lights may turn off automatically if you are beyond the range of the motion sensor NAVIGATION AND SCREEN The screen displays the time temperature and current battery charge if applicable until
35. ge door opener is operating on battery power it will run slower and the battery status LED will glow solid orange a beep will sound approximately every 2 seconds The following features are unavailable when operating on battery power e Garage Door Opener Lights e Unattended close devices and features e g MyQ Smartphone Control and Timer to Close Battery Status LED 1 Unplug the garage door opener 2 Open the light lens on the right side panel of the garage door opener Use a Phillips head screwdriver to remove the battery cover on the garage door opener Partially insert the battery into the battery compartment with the terminals facing out Connect red and black wires from the garage door opener to the corresponding terminals on the battery Po 30 5 Replace the battery cover and plug in the garage door opener 6 Wait for the green Battery Status LED to start flashing before proceeding to test the battery STEP 2 Test the Battery 1 Unplug the garage door opener The battery status LED will glow solid orange indicating opener is operating on battery power or will flash indicating low battery power 2 Open and close the door using the remote control or door control 3 Plug in the garage door opener Verify the battery status LED is flashing green indicating the battery is charging
36. he hole in the sensor bracket and attach with the wing nut The lenses on both sensors should point toward each other Make sure the lens is not obstructed by the sensor bracket 2 Not provided Not provided No more than 6 inches 15 cm Wing Nut 1 4 20 Carriage Bolt 1 4 20x1 2 22 OPTION C FLOOR INSTALLATION Use an extension bracket not provided or wood block to raise the sensor bracket if needed 1 Carefully measure the position of both sensor brackets so they will be the same distance from the wall and unobstructed 2 Attach the sensor brackets to the floor using concrete anchors not provided 3 Slide the carriage bolt into the slot on each sensor Insert the bolt through the hole in the sensor bracket and attach with the wing nut The lenses on both sensors should point toward each other Make sure the lens is not obstructed by the sensor bracket 4 Carriage Bolt 1 4 20x1 2 Installation STEP 14 Wire the Safety Reversing Sensors lf your garage already has wires installed for the safety reversing sensors proceed to page 24 HARDWARE Insulated Staple Not Shown OPTION A INSTALLATION WITHOUT PRE WIRING 1 Run the wire from both sensors to the garage door opener Attach the wire to the wall and ceiling with the staples 2 Strip 7 16 inch 11 mm of insulation from each set of wires Separate the wires Twist the white wires together Twist the w
37. hin sight of the door ata minimum height of 5 feet 1 5 m where small children cannot reach and away from the moving parts of the door For gang box installations itis not necessary to drill holes or install the drywall anchors Use the existing holes in the gang box NOTE Your product may look different than the illustrations HARDWARE Screw Screw 6 32x1 2 5 ATA 6ABx1 2 SAOATINOND Drywall po Anchors 2 mo 19 SNOOP ow 1 7 16 11 mm Kasi 1 Z a 4 5 Strip 7 16 inch 11 mm of insulation from one end of the wire and separate the wires Connect one wire to each of the two screws on the back of the door control The wires can be connected to either screw If your garage is pre wired for the door control choose any two wires to connect note which wires are used so the correct wires are connected to the garage door opener in a later step Mark the location of the bottom mounting hole and drill a 5 32 inch 4 mm hole Install the bottom screw allowing 1 8 inch 3 mm to protrude from the wall Position the bottom hole of the door control over the screw and slide down into place Lift the push bar up and mark the top hole Remove the door control from the wall and drill a 5 32 inch 4 mm hole for the top screw Position the bottom hole of the door control over the screw and slide down into place Attach the top screw Installation STEP 11 Wire the door control to the garage door opener STEP 12
38. hite black wires together 3 _ Insert the white wires into the white terminal on the garage door opener Insert the white black wires into the grey terminal on the garage door opener To insert or remove the wires from the terminal push in the tab with a screwdriver tip 23 Installation STEP 14 Wire the Safety Reversing Sensors continued OPTION B PRE WIRED INSTALLATION 1 Cutthe end ofthe safety reversing sensor wire making sure there is enough wire to reach the pre installed wires from the wall Separate the safety reversing sensor wires and strip 7 16 inch 11 mm of insulation from each end Choose two of the pre installed wires and strip 7 16 inch 11 mm of insulation from each end Make sure that you choose the same color pre installed wires for each sensor Connect the pre installed wires to the sensor wires with wire nuts making sure the colors correspond for each sensor For example the white wire would connectto the yellow wire and the white black wire would connect to the purple wire At the garage door opener strip 7 16 inch 11 mm of insulation from each end of the wires previously chosen for the safety reversing sensors Twist the like colored wires together Insert the wires connected to the white safety sensor wires to the white terminal on the garage door opener Insert the wires that are connected to the white black safety sensor wires to the grey terminal on the garage door opener 2 24 1
39. ion test safety reversal system Door MUST reverse on contact with a 1 1 2 3 8 cm high object or a 2x4 laid flat on the floor To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution disconnect ALL electric and battery power BEFORE performing ANY service or maintenance DO NOT install on a one piece door if using devices or features providing unattended close Unattended devices and features are to be used ONLY with sectional doors Installation STEP 1 Determine the header bracket location Header Wall OPTIONAL CEILING MOUNT 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling otherwise garage door might NOT reverse when required DO NOT install header bracket over Vertical Centerline of Garage Door FOR HEADER BRACKET Structural Supports Unfinished Se drywall Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry NEVER try to loosen move or adjust garage door springs cables pulleys brackets or their hardware ALL of which are under EXTREME tension ALWAYS call a trained door systems technician if garage door binds sticks or is out of balance An unbalanced garage door might NOT reverse when required a Sectional door with curved track One piece door with horizontal track Installation procedures vary according to garage door types Follow the instructions which apply
40. lect LOCK from the menu When the LOCK feature is on a message displays on the screen Operation MENU OPTIONS CONTINUED TIMER TO CLOSE TTC Factory default is set to off The Timer to Close feature automatically closes the door after a specified time period and can be adjusted using the door control DO NOT enable TTC if operating a one piece door TTC is to be used ONLY with sectional doors The garage door opener will beep and the lights will flash before closing the door The TTC feature will deactivate if the garage door encounters an obstruction twice or the safety reversing sensors are incorrectly installed The garage door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are correctly installed When the obstruction has been cleared or the safety reversing sensors have been aligned the door will close when the garage door opener is activated TTC WILL NOT work if the garage door opener is operating by battery power or if the safety reversing sensors are misaligned This feature is NOT intended to be the primary method of closing the door A keyless entry should be installed in the event of an accidental lock out when using this feature To turn TTC on or off or to set the TTC time interval 1 Select TTC from the menu 2 Selecta time interval of 1 5 10 minutes or a custom setting up to 99 minutes Once the TTC has been set and the door is open a message will display on the screen
41. n is pressed f To replace battery pry open the case firstin the middle 1 then at each side 2 and 3 with the visor clip Replace the o 3 batteries with only 3V CR2032 coin cell batteries Insert battery positive side up Dispose of old batteries properly 9 1 _ NOTICE To complywith FCC and or Industry Canada IC rules adjustment or modifications of this transceiver are prohibited THERE ARENOUSER SERVICEABLE PARTS This device complies with Part 15 ofthe FCC rulesand IC RSS 210 Operation is subject to the following two conditions 1 thisdevice may not cause harmfulinterference and 2 this device must accept any interference received including interference that may cause undesired operation This device must be installed in a waywhere a minimum8 20cm distance is maintained between users bystandersand device AVIS Lesr glesde la FCC et ou d Industrie Canada IC interdisent tout ajustement ou toute modification de ce r cepteur IL N EXISTE AUCUNEPIECE SUSCEPTIBLE D ETREENTRETENUEPAR L UTILISATEUR Cet appareilest conforme aux dispositions de la partie 15 du reglement de la FCC et de Inorme IC RSS 210 Son utilisation est assujettie auxdeuxconditoins suivantes 1 ce dispositif ne peut causerdesinterf rencesnuisibles et 2 ce dispositif doit acceptertoute interf rence recue ycomprisune interf rence pouvant causerun fonctionnement non souhait Cet appareildoit tre install de mani re a laisserune distance d
42. nd sides of the U bracket Inner Trolley A Wear Pads Rail Tab N amp Front Rail Section TO DOOR Assembly STEP 2 Fasten the rail to the motor unit CAUTION To avoid SERIOUS damage to garage door opener use ONLY those bolts fasteners mounted in the top of the opener 1 Inserta 1 4 20x1 3 4 bolt into the cover protection bolt hole on the back end of the rail as shown Tighten securely with a 1 4 20 lock nut DO NOT overtighten 2 Remove the bolts from the top of the motor unit 3 Use the carton to support the front end of the rail 4 Place the U bracket flat side down onto the motor unit and align the bracket holes with the bolt holes 5 Fasten the U bracket with the previously removed bolts DO NOT use any power tools The use of power tools may permanently damage the garage door opener HARDWARE Bolt 1 4 20x1 3 4 Bolts Mounted in the garage door opener Bolt 1 4 20x1 3 4 U Bracket Cover Protection Bolt Hole Lock Nut 1 4 20 STEP 3 Install the idler pulley 1 Lay the belt beside the rail as shown Grasp the end with the hooked trolley connector and pass approximately 12 30 cm of belt through the window Keep the ribbed side toward the rail and allow itto hang until Assembly Step 4 2 Remove the tape from the idler pulley The inside center should be pre greased If dry regrease to ensure proper operation 3 Place the idler pull
43. nless garage doorway is clear of persons and obstructions NEVER use handle to pull door open or closed If rope knot becomes untied you could fall closed e The garage door opener light bulbs will turn on when the opener is initially plugged in power is DISCONNECT THE TROLLEY restored after interruption or when the garage door opener is activated The lights will turn off 1 The door should be fully closed if possible automatically after 4 1 2 minutes The lights will turn on when someone enters through the open 2 Pull down on the emergency release handle so the trolley release arm snaps to the vertical garage door and the safety reversing sensor infrared beam is obstructed see page 33 Use an position The door can now be raised and lowered as often as necessary incandescent A19 light bulb 100 watt maximum or for maximum energy efficiency a 26W 100W equivalent compact fluorescent light CFL bulb NOTE Do not use halogen short neck or specialty light bulbs as these may overheat the end panel or light socket Do not use LED bulbs as they may reduce the range or performance of your remote controls TO RECONNECT THE TROLLEY 1 Pull the emergency release handle toward the garage door opener so the trolley release arm snaps to the horizontal position The trolley will reconnect on the next UP or DOWN operation 33 Operation Door Control SYNCHRONIZE THE DOOR CONTROL To synchronize the door control to the gara
44. persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door 1 Open the door Place the garage door opener carton in the path of the door 2 Press the remote control push button to close the door The door will not move more than an inch 2 5 cm and the garage door opener lights will flash 10 times The garage door opener will not close from a remote control if the LED in either safety reversing sensor is off alerting you to the fact that the sensor is misaligned or obstructed Ifthe garage door opener closes the door when the safety reversing sensor is obstructed and the sensors are no more than 6 inches 15 cm above the floor call for a trained door systems technician 1 2 29 Battery Backup STEP 1 Install the Battery A WARNING To reduce the risk of FIRE or INJURY to persons e Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance e Use ONLY Chamberlain part 41A6357 1 for replacement battery e DO NOT dispose of battery in fire Battery may explode Check with local codes for disposal instructions CAUTION ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment The battery backup allows access in and out of your garage even when the power is out The battery does not have to be fully charged to operate the garage door opener When the gara
45. power outage Battery Status LED 39 Accessories 7702CB Outside Quick Release Required for a garage with NO access door 8808CB EL 8 Foot 2 4 m Rail Extension To allow an 8 foot 2 4 m door to open fully 041A5281 1 Extension Brackets Optional For safety reversing sensor installation onto the wall or floor CLLP1 Laser Parking Assistant Park in the right spot every time ES i A laser beam is activated by your EP garage door opener and projected on to the dashboard of your vehicle to guide perfect parking CLSS1 System Surge Protector The Garage Door Opener Surge Protector is designed to protect Chamberlain garage door Openers against damage from lightning and power surges Easy to install WSLCEV MyQ Interior Exterior Light Switch Monitor and control this wall light switch with the MyQ 8810CB 10 Foot 3 m Rail Extension To allow a 10 foot 3 m door to E open fully MyQ Accessories You can program up to 10 MyQ accessories to your MyQ account PILCEV MyQ Remote Lamp Control Monitor and control this plug in lamp switch with the MyQ Smartphone App eo Smartphone App 40 953EV 940EV 956EV CIGBU ES Remote Control Works with ALL Chamberlain openers from 1993 present MyQ compatible Includes visor clip Wireless Keypad For use outside of the home to enable access to the garage using a 4 digit PIN Works with ALL
46. r Parts Description Part Number Sprocket and Sprocket Cover with Screws 04101751 Garage Door Opener Parts End Panel with light socket 041D7639 1 Light Lens 041D7572 Light Socket 04100279 5 Transformer 041D0277 1 6 Cover 041D0614 23 7 Motor with Travel Module 041D1739 1 8 End Panel for Receiver Logic Board with light socket 041D8214 9 Receiver Logic Board O50DCTWF 10 Travel Module 041A7114 7 2014 The Chamberlain Group Inc All Rights Reserved Wi Fi is a registered trademark of Wi Fi Alliance App Store is a service mark of Apple Inc 114A4763B Google Play is a trademark of Google Inc
47. r until the trolley release arm is horizontal The trolley will re engage automatically when the garage door opener is activated NOTE If the holes in the curved door arm and the straight door arm do notalign reverse the straight door arm select two holes as far apart as possible and attach using bolts nuts and lock washers If the straight door arm is hanging down too far you may cut 6 inches 15 cm from the solid end Clevis Pin 5 16 x1 1 4 Ring Fastener HARDWARE Clevis Pin 5 16 x1 Hex Bolt 5 16 18x7 8 Lock Washer 5 16 18 Nut 5 16 18 17 CORRECT INCORRECT Straight lt ul Door AT Groove facing out Clevis Pin 5 16 x1 Lock Washer 5 16 18 Nut 5 16 18 Installation STEP 9 Connect the door arm to the trolley continued CORRECT INCORRECT OPTION B ONE PIECE DOORS IMPORTANT The groove on the straight door arm MUST face away from the curved door arm 1 Close the door Disconnect the trolley by pulling the emergency release handle Straight 2 Fasten the straight door arm and the curved door arm together to the longest possible length Door Arm Curved with a 2 or 3 hole overlap using the bolts nuts and lock washers Groove Door 3 Attach the straight door arm to the door bracket using the clevis pin Secure with the ring fastener facing out Arm 4 Attach the curved door arm to the trolley using the clevis pin
48. reference only and your product may look different Header bracket Pulley Door bracket Curved door arm Straight door arm Packaged inside front rail section Trolley NOTE Be sure to assemble the trolley before sliding onto rail Emergency release rope and handle Rail 1 front and 4 center sections Hanging brackets 2 Packaged inside the front rail section Garage door opener motor unit Sprocket cover and screws U bracket Belt Door control Smart Control Panel Remote control 2 The Protector System Safety reversing sensors with 2 conductor white and white black wire attached Sending Sensor 1 Receiving Sensor 1 and Safety Sensor Brackets 2 NOT SHOWN White and red white wire Owner s manual Hardware MO OW gt m I0 voOozZzgrAac Preparation Hardware ASSEMBLY INSTALLATION Bolt Bolt 1 4 20x1 3 4 Self Threading Screw 1 4 14x5 8 2 Threaded Shaft with Spring Carriage Bolt Wing Nut 1 4 20 2 pen Eee Tee LT Trolley Nut 1 4 20x1 2 2 Hl 4 1 Lock Washer Ea a Nut 5 16 18 5 Ring Fastener 3 Master Link 9 16186 _ N E Lock Nut 4 1 4 20 0 eae no DOOR CONTROL eee packed with the Screw 6 32x1 2 S sprocket cover Insulated A o mai O ee E Drywall Anchors 2 Screw 6ABx1 2 Not Shown e ut 3 8 Lock Washer 3 8 m Assembly STEP 1 Assemble the rail and install the trolley
49. rocedure To make a permanent connection through the 7 8 inch hole in the top of the motor unit according to local code 1 Remove the motor unit cover screws and set the cover aside 2 Remove the attached 3 prong cord 3 Connect the black line wire to the screw on the brass terminal the white neutral wire to the screw on the silver terminal and the ground wire to the green ground screw The opener must be grounded 4 Reinstall the cover Ground Tab pil Green Ground Installation STEP 16 Aligning the safety reversing sensors The door will not close if the sensors have not been installed and aligned correctly When the light beam is obstructed or misaligned while the door is closing the door will reverse and the garage door opener lights will flash ten times Ifthe door is already open it will not close 1 Check to make sure the LEDs in both sensors are glowing steadily The LEDs in both sensors will glow steadily if they are aligned and wired correctly The sensors can be aligned by loosening the wing nuts aligning the sensors and tightening the wing nuts If the receiving sensor is in direct sunlight switch it with sending sensor so it is on the opposite side of the door invisible light beam Green LED RECEIVING SENSOR Amber LED SENDING SENSOR 26 IF THE AMBER LED ON THE SENDING SENSOR IS NOT GLOWING 1 Make sure there is power to the garage door opener 2 Make sure the sensor
50. ser such as Safari or Chrome on your mobile device and go to setup myqdevice com Follow the on screen prompts to add the garage door opener to your home Wi Fi network 4 SETUP YOUR MyQ ACCOUNT Download the MyQ app from the App Store or Google Play store Sign up for your MyQ account and add the MyQ serial number to your account or App Store Congratulations you ve successfully completed the setup Enjoy MyQ Smartphone Control In addition to controlling your garage door opener you can control your house lighting with additional MyQ accessories see page 40 NOTES The MyQ Smartphone Control WILL NOT work if the garage door opener is operating on battery power To erase the Wi Fi settings see page 36 To learn more go to wifihelp chamberlain com Operation IMPORTANT SAFETY INSTRUCTIONS A amp WARNING To reduce the risk of SEVERE INJURY or DEATH READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ALWAYS keep remote controls out of reach of children NEVER permit children to operate or play with garage door control push buttons or remote controls ONLY activate garage door when it can be seen clearly itis properly adjusted and there are no obstructions to door travel ALWAYS keep garage door in sight and away from people and objects until completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR NO ONE SHOULD GO UNDER A STOPPED PARTIALLY OPENED DOOR lf possible use emergency r
51. t the logic board Replace travel module if necessary Manually open and close the door Check for binding or obstructions such as a broken spring or door No movement only a single click ock correctas needed Replace logic board if necessary Manually open and close the door Check for binding or obstructions such as a broken spring or door Opener hums for 1 2 seconds no movement ock correct as needed Replace motor if necessary 1 6 Door coasts after ithas come to a complete stop Program travel to coasting position or have door balanced by a trained door systems technician 2 1 5 No movement or sound Replace logic board 3 2 Unable to setthe travel or retain position Check travel module for proper assembly replace if necessary 3 3 The battery status LED is constantly flashing green Battery backup charging circuit error replace the logic board 4 1 4 Door is moving stops or reverses Manually open and close the door Check for binding or obstructions such as a broken spring or door lock correct as needed If the door is binding or sticking contact a trained door systems technician If door is not binding or sticking attempt to reprogram travel refer to page 27 Troubleshooting DIAGNOSTIC CODE SYMPTOM Up Arrow Down Arrow Flash es Flash es 4 5 Opener runs approximately 6 8 stops and reverses 4 6 The garage door opener will not close and the light bulbs flash The garage door opener can beep for several reasons
52. the garage door opener until 3 beeps are heard Approximately 6 seconds ERASE A MyQ ACCOUNT 1 Go to ww mychamberlain com to access your MyQ account 2 Click on the Account tab 3 Click Edit User 4 Click Delete this account 5 Click Delete Go to wifihelp chamberlain com for more details 36 Maintenance Maintenance Schedule EVERY MONTH Manually operate door Ifitis unbalanced or binding call a trained door systems technician Check to be sure door opens and closes fully Adjust if necessary see page 27 Test the safety reversal system Adjustif necessary see page 27 EVERY YEAR Oil door rollers bearings and hinges The garage door opener does not require additional lubrication Do not grease the door tracks Test the battery backup and consider replacing the battery to ensure the garage door opener will operate during an electrical power outage see page 30 to test the battery backup 37 The Remote Control Battery 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH e NEVER allow small children near batteries e lf battery is swallowed immediately notify doctor To reduce risk of fire explosion or chemical burn e Replace ONLY with 3V CR2032 coin batteries e DO NOT recharge disassemble heat above 212 F 100 C or incinerate The 3V CR2032 lithium battery should produce power for up to 3 years If the battery is low the remote control s LED will not flash when the butto
53. to your door Header Wall Header Wall 1 Close the door and mark the inside vertical centerline of the garage door Pra p 2 5em 2 Extend the line onto the header wall above the door You can fasten the header bracket within 4 Track i Track feet 1 22 m of the left or right of the door center only if a torsion spring or center bearing plate is Highest in the way or you can attach it to the ceiling see page 11 when clearance is minimal It may be Point of Highest mounted on the wall upside down if necessary to gain approximately 1 2 1 cm Ifyou need to Travel Point of Travel install the header bracket on a 2x4 on wall or ceiling use lag screws not provided to securely fasten the 2x4 to structural supports as shown here and on page 11 3 Open your door to the highest point of travel as shown Draw an intersecting horizontal line on the header wall 2 5 cm above the high point One piece door without track One piece door without track e 2 5cm above the high point for sectional door and one piece door with track jamb hardware pivot hardware e 8 20 cm above the high point for one piece door without track _ Header Wall No Header Wall This height will provide travel clearance for the top edge of the door NOTE ifthe total number of inches 7 8 20 cm a 8 20 cm exceeds the height available in your garage use the maximum height possible or refer to page 11 for ZN 4 A
54. used to move the door as needed 1 Press and hold the Adjustment Button until the UP Button begins to flash and or a beep is heard 2 Press and hold the UP Button until the door is in the desired UP position 3 Once the door is in the desired UP position press and release the Adjustment Button The garage door opener lights will flash twice and the DOWN Button will begin to flash IMPORTANT NOTE For one piece door installations refer to page 27 4 Press and hold the DOWN button until the door is in the desired DOWN position 4 5 Once the door is in the desired DOWN position press and release the Adjustment Button The garage door opener lights will flash twice and the UP Button will begin to flash 6 Press and release the UP Button When the door travels to the programmed UP position the DOWN Button will begin to flash 7 Press and release the DOWN Button The door will travel to the programmed DOWN position Programming is complete Ifthe garage door opener lights are flashing 5 times during the steps for Program the Travel the programming has timed out If the garage door opener lights are flashing 10 times during the steps for Program the Travel the safety reversing sensors are misaligned or obstructed refer to page 26 When the sensors are aligned and unobstructed cycle the door through a complete up and down cycle using the remote control or the UP and DOWN buttons Programming is complete If you are unable to operate the door up and do
55. wing items 2 2X4 Pieces of wood May be used to fasten the header bracket to the structural supports Also used to position the garage door opener during installation and for testing the safety reversing sensors Support bracket and fastening hardware Must be used if you have a finished ceiling in your garage Extension brackets MODEL 041A5281 1 or wood blocks Depending upon garage construction extension brackets or wood blocks may be needed to install the safety reversing sensor Fastening hardware Alternate floor mounting of the safety reversing sensor will require hardware not provided Outside quick release MODEL 7702CB Required for a garage with NO access door Door reinforcement Required if you have a lightweight steel aluminum fiberglass or glass panel door Rail extension kit Required if your garage door is more than 7 feet 2 13 m high Tools Needed 0000 A Preparation Carton Inventory Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below Accessories vary depending on the garage door opener model purchased Depending on your model other accessories may be included with your garage door opener Instructions for these accessories will be attached to the accessory and are not included in this manual Save the carton and packing material until the installation and adjustment is complete The images throughout this manual are for
56. wire is not shorted broken 3 Make sure the sensor has been wired correctly white wires to white terminal and white black wires to grey terminal ee 4 R Es a a iad WHITE WHITE GREY IF THE GREEN LED ON THE RECEIVING SENSOR IS NOT GLOWING 1 Make sure the sensor wire is not shorted broken 2 Make sure the sensors are aligned STEP 17 Ensure the door control is wired correctly Ifthe door control has been installed and wired correctly a message will display on the Smart Control Panel screen Adjustments Introduction 4 amp WARNING Without a properly installed safety reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door e Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system e After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 3 8 cm high object or 2x4 laid flat on floor CAUTION To prevent damage to vehicles be sure fully open door provides adequate clearance Your garage door opener is designed with electronic controls to make setup and adjustments easy The adjustments allow you to program where the door will stop in the open UP and close DOWN position The electronic controls sense the amount of force required to open and close the door The force is adjusted automatically when you program the travel
57. with the selected time interval To temporarily suspend the TTC feature select HOLD Select REL to resume normal TTC operation PROGRAM Any compatible remote control wireless keyless entry or MyQ devices can be programmed to the garage door using the PROGRAM option from the menu 35 Remote Control and Keyless Entry Your remote control has been programmed at the factory to operate with your garage door opener randomly accessing over 100 billion new codes with each use Your garage door opener can be programmed with up to 8 remote controls 1 keyless entry 2 Security 2 0 door controls and 6 MyQ accessories Older Chamberlain remote controls are NOT compatible see page 40 for compatible accessories Programming can be done through the door control or the learn button on the garage door opener To program additional accessories refer to the instructions provided with the accessory or visit www chamberlain com If your vehicle is equipped with a Homelink you may require an external adapter depending on the make model and year of your vehicle Visit www homelink com for additional information TO ADD REPROGRAM OR CHANGE A REMOTE CONTROL KEYLESS ENTRY PIN USING THE DOOR CONTROL 1 Press the navigation button below MENU to view the Features menu 2 Use the navigation buttons to scroll to PROGRAM 3 Select REMOTE or KEYPAD to program from the program menu 4 Remote Control Press the button on the remote control that you wish
58. wn repeat the steps for Programming the Travel UP Button Adjustment Button 28 Adjustments STEP 2 Test the Safety Reversal System 4 amp WARNING Without a properly installed safety reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door e Safety reversal system MUST be tested every month e After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 3 8 cm high object or 2x4 laid flat on the floor 1 With the door fully open place a 1 1 2 inch 3 8 cm board or a 2x4 laid flat on the floor centered under the garage door 2 Operate the door in the down direction The door MUST reverse on striking the obstruction Ifthe door stops and does not reverse on the obstruction the down travel needs to be increased refer to Adjustment Step 1 Repeat the test When the door reverses on the 1 1 2 3 8 cm board or 2x4 laid flat remove the obstruction and run the opener through 3 or 4 complete travel cycles to test adjustment Ifthe garage door opener continues to fail the safety reversal test call a trained door systems technician 1 2 STEP 3 Test the Protector System 4 amp WARNING Without a properly installed safety reversing sensor
59. x1 5 8 Door Spring 2x4 Structural Support Lag Screw 5 16 9x1 5 8 Horizontal Garage Door Header Wall Line Optional Mounting Holes Highest Point of Garage Bo Door Travel Garage Door 11 Installation STEP 3 Attach the rail to the header bracket STEP 4 Position the garage door opener CAUTION 1 Position the opener on the garage floor below the header bracket Use packing material as a protective base NOTE If the door spring is in the way you will need help Have someone hold the opener securely on a temporary support to allow the rail to clear the spring 2 Position the rail bracket against the header bracket 3 Align the bracket holes and join with a clevis pin as shown To prevent damage to garage door rest garage door opener rail on 2x4 placed on top section of door 1 Remove the packing material and lift the garage door opener onto a ladder oe Inserts Ng fastener to secure 2 Fully open the door and place a 2x4 laid flat under the rail For one piece doors without tracks HARDWARE lay the 2x4 on it s side i NOTE A 2x4 is ideal for setting the distance between the rail and the door if the ladder is not tall Clevis Pin 5 16 x1 1 2 Ring Fastener enough you will need help at this point If the door hits the trolley when itis raised pull the trolley release arm down to disconnect the inner and outer trolley Slide the outer trolley toward the garage door opener The

Chamberlain HD950WF Instructions / Assembly

Contents

Download Pdf Manuals

Related Search

Related Contents