Chamberlain WD832KEV Instructions / Assembly
Contents
1. 30 Operation IMPORTANT SAFETY INSTRUCTIONS A amp WARNING To reduce the risk of SEVERE INJURY or DEATH READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ALWAYS keep remote controls out of reach of children NEVER permit children to operate or play with garage door control push buttons or remote controls ONLY activate garage door when it can be seen clearly itis properly adjusted and there are no obstructions to door travel ALWAYS keep garage door in sight and away from people and objects until completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR NO ONE SHOULD GO UNDER A STOPPED PARTIALLY OPENED DOOR lf possible use emergency release handle to disengage trolley ONLY when garage door is CLOSED Use caution when using the release with the door opener Weak or broken springs or unbalanced door could resultin an open door falling rapidly and or unexpectedly and increasing the risk of SEVERE INJURY or DEATH NEVER use emergency release handle unless garage doorway is clear of persons and obstructions NEVER use handle to pull garage door open or closed If rope knot becomes untied you could fall After ANY adjustments are made the safety reversal system MUST be tested 31 10 16 Safety reversal system MUST be tested every month Garage door MUST reverse on contact with 1 1 2 3 8 cm high2. Installation Metal or light weight doors using a vertical angle iron brace between the door panel support STEP 8 Install the door bracket and the door bracket Drill 3 16 fastening holes Secure the door bracket using the two self threading screws CAUTION Figure 2 lt lt lt _qqqoqoOoq e Alternately use two 5 16 bolts lock washers and nuts not provided Figure 3 Fiberglass aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE Metal insulated or light weight factory reinforced doors installation of door bracket Contact your door manufacturer for reinforcement kit Drill 3 16 fastening holes Secure the door bracket using the self threading screws Figure 1 shows one piece of angle iron as the horizontal brace For the vertical brace 2 pieces of angle Figure 4 iron are used to create a U shaped support The best solution is to check with your garage door Wood Doors manufacturer for an opener installation door reinforcement kit e Use top and bottom or side to side door bracket holes Drill 5 16 holes through the door and NOTE Many door reinforcement kits provide for direct attachment of the clevis pin and door arm In this secure bracket with 5 16 x2 carriage bolts lock washers and nuts not provided Figure 5 case you will notneed the door bracket proceed to the next step NOTE The 1 44 14x5 8 self threading screws are not intended for use on
3. Clevis Pin 5 16 x1 1 2 Ring Fastener 1 Remove the packing material and lift the garage door opener onto a ladder 2 Fully open the door and place a 2x4 laid flat under the rail For one piece doors without tracks lay the 2x4 on it s side Clevis Pin NOTE A 2x4 is ideal for setting the distance between the rail and the door If the ladder is not tall 5 16 x1 1 2 enough you will need help at this point Ifthe door hits the trolley when itis raised pull the trolley release a27 arm down to disconnect the inner and outer trolley Slide the outer trolley toward the garage door _ C opener The trolley can remain disconnected until instructed NIAC Ring Fastener One piece door without tracks All other door types Installation STEP 5 Hang the garage door opener 4 amp WARNING To avoid possible SERIOUS INJURY from a falling garage door opener fasten it SECURELY to structural supports of the garage Concrete anchors MUST be used ifinstalling ANY brackets into masonry Hanging the garage door opener will vary depending on your garage Below are three example installations Your installation may be different For ALL installations the garage door opener MUST be connected to structural supports The instructions illustrate one of the examples below Finished Ceiling HARDWARE Lag Screw 5 16 9x1 5 8 pii 00000000D Lock Washer 5 16 18 Nut 5 16 18 Hex Bolt 5 16
4. Assembly STEP 2 Fasten the rail to the motor unit CAUTION To avoid SERIOUS damage to garage door opener use ONLY those bolts fasteners mounted in the top of the opener 1 Inserta 1 4 20x1 3 4 bolt into the cover protection bolt hole on the back end of the rail as shown Tighten securely with a 1 4 20 lock nut Do NOT overtighten 2 Remove the bolt and nut from the top of the motor unit 3 Use the carton to support the front end ofthe rail 4 Place the U bracket flat side down onto the motor unit and align the bracket holes with the bolt holes 5 Fasten the U bracket with the previously removed bolt and lock nut DO NOT use any power tools The use of power tools may permanently damage the garage door opener HARDWARE Bolt and Nut Mounted in the garage door opener Bolt 1 4 20x1 3 4 Bolt Lock Nut 9 U Bracket Bolt 1 4 20x1 3 4 Cover Protection Bolt Hole Lock Nut 1 4 20 Assembly STEP 3 Install the idler pulley 1 Lay the belt beside the rail as shown Grasp the end with the hooked trolley connector and pass approximately 12 30 cm of belt through the window Keep the ribbed side toward the rail and allow itto hang until Assembly Step 4 Remove the tape from the idler pulley The inside center should be pre greased If dry regrease to ensure proper operation Place the idler pulley into the window as shown Insert the idler bolt from the top throug
5. ec lf you need to install the header bracket on a 2x4 on wall or ceiling use lag screws not q Header Wall jm header sai cm provided to securely fasten the 2x4 to structural supports odi Rie 20 cm ares 3 Open your door to the highest point of travel as shown Draw an intersecting horizontal line on Highest naar M Highest the header wall 2 5 cm above the high point T Point of ae e 2 5 cm above the high point for sectional door and one piece door with track J Travel e 8 20 cm above the high point for one piece door without track This height will provide travel clearance for the top edge of the door NOTE Ifthe total number of inches exceeds the height available in your garage use the maximum height possible or refer to page 12 for ceiling installation Hardware Pivot One piece door without track One piece door without track jamb hardware pivot hardware 11 Installation STEP 2 Install the header bracket You can attach the header bracket either to the wall above the garage door or to the ceiling Follow the instructions which will work best for your particular requirements Do not install the header bracket over drywall If installing into masonry use concrete anchors not provided Lag Screw 5 16 9x1 5 8 HARDWARE pihi OPTION A WALL INSTALLATION 1 Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown 2 Mark the ve
6. 1 Center the door bracket on the top of the door in line with the header bracket as shown lama 2 Markeither the left and right or the top and bottom holes Header Bracket Be e Metal Doors Cr e Drill 3 16 pilot holes and fasten the bracket with the self threading screws provided han Wood Doors Door Bracket 6 i Optional e Drill 5 16 holes and use 5 16 x2 carriage bolts lock washers and nuts not provided or 5 16 x1 al i en a a door ae exposed p P i i raming or for the optional 1 2 lag screws not provided depending on your installation needs ie installation use lag screws NOTE The door bracket may be installed on the top edge of the door if required for your installation Refer to the dotted line optional placement drawing 5 16 x1 1 2 not provided to fasten the door bracket Vertical Centerline of Garage Door Metal Door sp _ Self Threading Wood Door om 5 16 18 Screw 1 4 14x5 8 gt Lock Washer 5 16 Door Top of Door Bracket iy Top of Door Bracket h Inside Garage LIN Inside Garage Top Edge of S lt Top Edge Door AA Placement Optional Placement Carriage Bolt 5 16 x2 not provided 17 Installation STEP 9 Connect the door arm to the trolley Installation will vary according to the garage door type Follow the instructions which apply to your door OPTION A SECTIONAL DOORS IMPORTANT The groove on the straight door arm MUST face away
7. OR WOOD BLOCKS Depending upon garage construction extension brackets or wood blocks may be needed to install the safety reversing sensor m FASTENING HARDWARE Alternate floor mounting of the safety reversing sensor will require hardware not provided m OUTSIDE QUICK RELEASE MODEL 7702CB Required for a garage with NO access door m DOOR REINFORCEMENT Required if you have a lightweight steel aluminum fiberglass or glass panel door m RAIL EXTENSION KIT Required if your garage door is more than 7 feet 2 13 m high jn w UU 7 16 9 16 7 16 O Preparation Carton Inventory Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below Accessories vary depending on the garage door opener model purchased Depending on your model other accessories may be included with your garage door opener Instructions for these accessories will be attached to the accessory and are not included in this manual If anything is missing carefully check the packing material Hardware for assembly and installation is shown on the next page Save the carton and packing material until the installation and adjustment is complete The images throughout this manual are for reference only and your product may look different A Header bracket B Pulley C Door bracket D E Curved door arm Straight door arm Packaged inside front rail section Trolley NOTE Be sure to assemble the trolley befor
8. Once the TTC has been set and the door is open the selected close interval will blink and begin to count down to close the door e Activate Press and hold the ON button until one of the TTC LEDs light up Then press the ON button again to cycle through the time interval options the corresponding TTC LED will light for each time interval The garage door opener light bulbs will blink as confirmation Deactivate Press and hold the OFF button until all TTC LEDs turn off and a beep is heard from the motor unit Temporarily hold door open suspend TTC Press and release the HOLD OPEN button Press the HOLD OPEN button again to resume normal TTC operation PROGRAM Any compatible remote controls wireless keyless entry or MyQ accessories can be programmed to the garage door opener by pressing the Learn button Command LED Switch Push Bar LEARN Butt see 1 5 and Ala OEI utton 9 an Button TTC OFF TTC 10 Minute MONTE LOCK Button TTC LED LIGHT Button CJ Motion Sensor 34 Remote Control Your remote control has been programmed at the factory to operate with your garage door opener Older Chamberlain remote controls are NOT compatible see page 39 for compatible accessories Programming can be done through the door control or the learn button the garage door opener To program additional accessories refer to the instructions provided with the accessory or visit www chamberlain com If your vehicle is equipped with a H
9. will flash before closing the door The TTC feature will deactivate if the garage door encounters an obstruction twice or the safety reversing sensors are incorrectly installed The garage door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are correctly installed When the obstruction has been cleared or the safety reversing sensors have been aligned the door will close when the garage door opener is activated TTC WILL NOT work if the garage door opener is operating by battery power or if the safety reversing sensors are misaligned This feature is NOT intended to be the primary method of closing the door A keyless entry should be installed in the event of an accidental lock out when using this feature MyQ MyQ technology uses a 900MHz signal to provide two way communication between the garage door opener and MyQ enabled accessories Your garage door opener is compatible with up to 8 MyQ accessories REMOTE CONTROLS AND DOOR CONTROLS MyQ Your garage door opener has already been programmed at the factory to operate with your remote control which changes with each use randomly accessing over 100 billion new codes Compatible with MyQ enabled accessories see page 39 NOTE Older Chamberlain remoie controls door controls and third party products are not compatible MEMORY CAPACITY Up to 8 Up to 2 MyQ door controls Up to 1 MyQ Accessories Remote Controls Do
10. 18x7 8 1 On finished ceilings use the lag screws to attach a support bracket not provided to the structural supports before installing the garage door opener 2 Make sure the garage door opener is aligned with the header bracket Measure the distance from each side of the garage door opener to the support bracket 3 Cutboth pieces of the hanging bracket not provided to required lengths 4 Attach the end of each hanging bracket to the support bracket with appropriate hardware not provided 5 Attach the garage door opener to the hanging brackets with the hex bolts lock washers and nuts 6 Remove the 2x4 and manually close the door If the door hits the rail raise the header bracket Finished 7_ lt Ceiling 0 provided Lag Serew Lag Screw 5 16 5 16 9x1 5 8 9x1 5 8 4 5 Hex Bolt 5 16 18x7 8 Lock Washer 5 16 18 not provided Nut 5 16 18 Installation STEP 6 Install the light bulbs STEP 7 Attach the emergency release rope and handle To prevent possible OVERHEATING of the end panel or light socket Is prevent possible SERIOUS INJURY or DEATH from a falling garage door e Use ONLY A19 incandescent 100W maximum or compact fluorescent 26W maximum light lf possible use emergency release handle to disengage trolley ONLY when garage door is bulbs CLOSED Weak or broken springs or unbalanced door could resultin an open door falling rapidly DO NOT use incandescent bulbs larger than
11. The groove on the straight door arm MUST face away from the curved door arm 1 2 3 Close the door Disconnect the trolley by pulling the emergency release handle Fasten the straight door arm and the curved door arm together to the longest possible length with a 2 or 3 hole overlap using the bolts nuts and lock washers Attach the straight door arm to the door bracket using the clevis pin Secure with the ring fastener Attach the curved door arm to the trolley using the clevis pin Secure with the ring fastener Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal Clevis Pin 5 16 x1 1 4 Clevis Pin 5 16 x1 HARDWARE Hex Bolt 5 16 18x7 8 Ring Fastener Nut 5 16 18 Lock Washer 5 16 18 19 CORRECT INCORRECT Straight Door Arm Straight Door Arm Curved Curved Door Arm Groove fidi Door facing out Arm ole Ring Fastener astener is sct ESN Nut 5 16 18 o 4 Lock Washer 5 16 18 N Clevis Pin 5 16 x1 Ring Fastener Nut S618 g Lock Washer 5 16 18 e ooo0oo00000Q000 e Clevis Pin a V Ehe Hex Bolt 5 16 18x7 8 Clevis Pin 1 6 x1 Installation Strip 7 16 inch 11 mm ofinsulation from one end of the wire and separate the wires STEP 10 Install the door control Connect one wire to each of the two screws on the back of the
12. door control The wires can be connected to either screw If your garage is pre wired for the door control choose any two A A WAR N l NG wires to connect note which wires are used so the correct wires are connected to the garage door opener in a later step Poa To prevent possible SERIOUS INJURY or DEATH from electrocution 3 Mark the location of the bottom mounting hole and drill a 5 32 inch 4 mm hole e Be sure power is NOT connected BEFORE installing door control 4 Install the bottom screw allowing 1 8 inch 3 mm to protrude from the wall Connect ONLY to 12 VOLT low voltage wires 5 Position the bottom hole of the door control over the screw and slide down into place F 6 _Liftthe push bar up and mark the top hole To preveni pessble SERIOUS INJUAY or DEATH romadosing garage oor aE 7 cane the door ae from the wal and drill a 5 32 inch 4 mm hole for the top screw Install door control within sight of garage door out of reach of children ata minimum height of 5 8 Position the bottom hole of the door control over the screw and slide down into place Attach feet 1 5 m and away from ALL moving parts of door the top screw NEVER permit children to operate or play with door control push buttons or remote control transmitters Activate door ONLY when it can be seen clearly is properly adjusted and there are no obstructions to door travel 7 16 11 mm ALWAYS keep garage door in sight until completely closed NEVER p
13. from the curved door arm 1 Close the door Disconnect the trolley by pulling the emergency release handle 2 Attach the straight door arm to the outer trolley using the clevis pin Secure with the ring fastener 3 Attach the curved door arm to the door bracket using the clevis pin Secure with the ring fastener 4 Bring arm sections together Find two pairs of holes that line up and join sections Select holes as far apart as possible to increase door arm rigidity and attach using the bolts nuts and lock washers 5 Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal The trolley will re engage automatically when the garage door opener is activated NOTE If the holes in the curved door arm and the straight door arm do notalign reverse the straight door arm select two holes as far apart as possible and attach using bolts nuts and lock washers If the straight door arm is hanging down too far you may cut 6 inches 15 cm from the solid end HARDWARE Clevis Pin 5 16 x1 1 4 Clevis Pin 5 16 x1 Hex Bolt 5 16 18x7 8 Ring Fastener Nut 5 16 18 Lock Washer 5 16 18 18 CORRECT Ring Fastener Nut 5 16 18 INCORRECT Groove facing out Lock Washer 5 16 18 O Clevis Pin 5 16 x1 Installation STEP 9 Connect the door arm to the trolley continued OPTION B ONE PIECE DOORS IMPORTANT
14. has a cut out window at the door end see illustration The hole above this window is larger on the top of the rail than on the bottom A smaller hole 3 1 2 8 9 cm away is close to the rail edge Rotate the back rail so it has a similar hole close to the opposite edge about 4 3 4 12 cm from the far end 1 Remove the straight door arm and hanging bracket packaged inside the front rail and set aside for Installation Step 5 and 9 NOTE To prevent INJURY while unpacking the rail carefully remove the straight door arm stored within the rail section 2 Align the rail sections on a flat surface as shown and slide the tapered ends into the larger ones Tabs along the side will lock into place 3 Place the motor unit on packing material to protect the cover and rest the back end of the rail on top For convenience puta support under the front end of the rail 4 As a temporary stop insert a screwdriver into the hole 10 25 cm from the front end of the rail SLIDE TO STOPS ON TOP AND SIDES OF U BRACKET Wear Pads as shown 5 Check to be sure there are 4 plastic wear pads inside the inner trolley If they became loose Front Rail during shipping check all packing material Snap them back into position as shown ry DOOR Slide the trolley assembly toward the screwdriver as shown Slide the rail onto the U bracket until it reaches all the stops on the top and sides of the U bracket NO Window Cut Out
15. installed and aligned correctly When the light beam is obstructed or misaligned while the door is closing the door will reverse and the garage door opener lights will flash ten times If the door is already open it will not close The sensors can be aligned by loosening the wing nuts aligning the sensors and tightening the wing nuts Check to make sure the LEDs in both sensors are glowing steadily The LEDs in both sensors will glow steadily if they are aligned and wired correctly If the receiving sensor is in direct sunlight switch it with sending sensor so it is on the opposite side of the door invisible light beam Green LED Vy Amber LED d RECEIVING SENSOR SENDING SENSOR IF THE AMBER LED ON THE SENDING SENSOR IS NOT GLOWING 1 Make sure there is power to the garage door opener 2 Make sure the sensor wire is not shorted oroken 3 Make sure the sensor has been wired correctly white wires to white terminal and white black wires to grey terminal AN Ea Be Ze WHITE GREY IF THE GREEN LED ON THE RECEIVING SENSOR IS NOT GLOWING 1 Make sure the sensor wire is not shorted broken 2 Make sure the sensors are aligned STEP 17 Ensure the door control is wired correctly Ifthe door control has been installed and wired correctly the command LED on the Motion Detecting Control Panel will blink 27 Adjustments Introduction amp WARNING Without a properly installed safety
16. remove ALL ropes connected to garage door BEFORE installing opener to avoid entanglement Install garage door opener 7 feet 2 13 m or more above floor Mount the emergency release within reach but at least 6 feet 1 83 m above the floor and avoiding contact with vehicles to avoid accidental release NEVER connect garage door opener to power source until instructed to do so NEVER wear watches rings or loose clothing while installing or servicing opener They could be caughtin garage door or opener mechanisms 10 Install wall mounted garage door control e within sight of the garage door e outofreach of children at minimum height of 5 feet 1 5 m e away from ALL moving parts of the door Place entrapment warning label on wall next to garage door control Place manual release safety reverse test label in plain view on inside of garage door Upon completion of installation test safety reversal system Door MUST reverse on contact with a 1 1 2 3 8 cm high object or a 2x4 laid flat on the floor To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution disconnect ALL electric power BEFORE performing any service or maintenance DO NOT enable the Timer to Close functionality if operating either one piece or swinging garage doors To be enabled ONLY when operating a sectional door Installation STEP 1 Determine the header bracket location Header Wall OPTIONAL CEILING MOUNT 4 WARNING To prevent possible SERIOUS INJURY
17. the horizontal position The trolley will reconnect on the next UP or DOWN operation either manually or by using the door control or remote control Maintenance j NOTICE To complywith FCC and or Industry Canada IC rules adjustment or modificationsof this transceiverare prohibited THERE Mai ntenance Schedule ARENOUSER SERVICEABLE PARTS Any changesormodifications not expressly approved by the party responsible for compliance EVERY MONTH could void the user sauthorityto operate the equipment be ot M an an ae Fae This device complieswith Part 15 ofthe FCC rules and IC RSS 210 Operation is subject to the following two conditions 1 thisdevice s Manually operate door If itis unbalanced or binding call a trained door systems technician maynotcause harmfulinterference and 2 this device must acceptanyinterference received including interference that may cause e Check to be sure door opens and closes fully Adjust if necessary see page 28 undesired operation P ane y AC Y pag ThisClassBdigitalapparatuscomplieswith Canadian ICES 003 e Testthe safety reversal system Adjust if necessary see page 28 EVERY YEAR AVIS Lesr glesde la FCC et ou d Industrie Canada IC interdisent tout ajustement ou toute modification de ce r cepteur IL Oil il beari hi Th d dditi N EXISTEAUCUNE PIECE SUSCEPTIBLE D ETREENTRETENUEPAR L UTILISATEUR Toutchangementou toute modification non il door ro ers bearings and inges Ihe garage door o
18. 100W and or unexpectedly DO NOT use compact fluorescent light bulbs larger than 26W 100W equivalent NEVER use emergency release handle unless garage doorway is clear of persons and DO NOT use halogen bulbs obstructions DO NOT use short neck or specialty light bulbs NEVER use handle to pull door open or closed If rope knot becomes untied you could fall 1 Pull on the top sides of the light lens and rotate the light lens down 1 Insert one end of the emergency release rope through the handle Make sure that NOTICE is 2 Insertan A19 incandescent 100W maximum or compact fluorescent 26W 100W equivalent right side up Tie a knot atleast 1 inch 2 5 cm from the end of the emergency release rope light bulb into the light socket 2 _Insertthe other end of the emergency release rope through the hole in the trolley release arm 3 Rotate the lens up to close Mount the emergency release within reach but at least 6 feet 1 83 m above floor avoiding NOTE Do notuse halogen short neck or specialty light bulbs as these may overheat the end panel or contact with vehicles to prevent accidental release and secure with a knot light socket Do not use LED bulbs as they may reduce the range or performance of your remote controls NOTE Ifitis necessary to cut the emergency release rope seal the cut end with a match or lighter to prevent unraveling Ensure the emergency release rope and handle are above the top ofall vehicles to avoid entanglement
19. CHAMBERLAIN Models e WD832KEV 1 2 hp Belt Drive e HD620EV 3 4 hp Belt Drive FOR RESIDENTIAL USE ONLY CONTENTS Preparation ASSOMDlyicc os cts 5 ccescars acna Installation neea POWT eetarea nean aaiae aaae Adjustments Operation e e eee Features Please read this manual and the enclosed safety materials carefully Door Control E Fasten the manual near the garage door after installation Remote Control 34 35 E The door WILL NOT CLOSE unless the Protector System is connected and To Erase the Memory 4 35 properly aligned To Open the Door Manually 35 Periodic checks of the garage door opener are required to ensure safe operation Maintenance seeeeeeees 36 The model number label is located on the left side panel of your garage Troubleshooting 1 37 38 door opener Accessories W This garage door opener is compatible with MyQ and Security 2 0 accessories Warranty 0 eeseeeeeeeeees DO NOT enable the Timer to Close feature if you are installing the garage door Repair Parts opener on a one piece door The Timer to Close is to be used ONLY with sectional doors Write down the following information for future reference cus Serial Number www chamberlain com Date of Purchase The Chamberlain Group Inc 845 Larch Avenue Elmhurst Illinois 60126 1196 P
20. E COST OF THE PRODUCT COVERED HEREBY NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT Some states do not allow the exclusion or limitation of consequential incidental or special damages so the above limitation or exclusion may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state Repair Parts Rail Assembly Parts Description Belt Part Number 41A5250 Pulley 144054 Master Link Rail 4A1008 41A5665 Trolley Assembly 4105141 1 U Bracket 12D598 1 Not Shown Wear Pads 183A163 Hardware Bag 041A7920 2 Owner s Manual Accessories 114A4309 Installation Parts Description Curved Door Arm Part Number 178B35 Door Bracket with Clevis Pin and Fastener 41A5047 1 Emergency Release Rope and Handle 41A2828 Header Bracket with Clevis Pin and Fastener 41A5047 2 Remote Control Visor Clip 29B137 Safety Sensor Bracket 41A5266 1 Safety Sensor Kit Receiving and sending sensors with wire 41A5034 Straight Door Arm 178B34 White and Red White Wire 41B4494 1 10 11 3V2030 Lithium Battery Hanging Brackets 10A20 12B776 Description Part Number 1 Motion Detecting 41A7327 1 Control Panel 2 Remote Control 953ESTD 41 Repair P
21. IED WARRANTIES FOR THE PRODUCT INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED COMPONENT S AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD Some States do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you THIS LIMITED WARRANTY DOES NOT COVER NON DEFECT DAMAGE DAMAGE CAUSED BY IMPROPER INSTALLATION OPERATION OR CARE INCLUDING BUT NOT LIMITED TO ABUSE MISUSE FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT REPLACEMENT OF CONSUMABLE ITEMS E G BATTERIES IN REMOTE CONTROL TRANSMITTERS AND LIGHT BULBS OR UNITS INSTALLED FOR NON RESIDENTIAL USE THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH OR RELATING TO THE GARAGE DOOR OR GARAGE DOOR HARDWARE INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS DOOR ROLLERS DOOR ALIGNMENT OR HINGES THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE OR INABILITY TO USE THIS PRODUCT IN NO EVENT SHALL SELLER S LIABILITY FOR BREACH OF WARRANTY BREACH OF CONTRACT NEGLIGENCE OR STRICT LIABILITY EXCEED TH
22. TE CONTROLS AND KEYLESS ENTRIES 1 Press and hold the learn button on garage door opener until the learn LED goes out approximately 6 seconds All remote control and keyless entry codes are now erased Reprogram any accessory you wish to use ERASE ALL DEVICES Including MyQ enabled accessories 1 Press and hold the learn button on garage door opener until the learn LED goes out approximately 6 seconds 2 Immediately press and hold the learn button again until the learn LED goes out All codes are now erased Reprogram any accessory you wish to use To Open the Door Manually amp WARNING To prevent possible SERIOUS INJURY or DEATH froma falling garage door e Ifpossible use emergency release handle to disengage trolley ONLY when garage door is CLOSED Weak or broken springs or unbalanced door could result in an open door falling rapidly and or unexpectedly NEVER use emergency release handle unless garage doorway is clear of persons and obstructions e NEVER use handle to pull door open or closed If rope knot becomes untied you could fall DISCONNECT THE TROLLEY 1 The door should be fully closed if possible 2 Pull down on the emergency release handle so the trolley release arm snaps to the vertical position The door can now be raised and lowered as often as necessary RECONNECT THE TROLLEY 1 Pull the emergency release handle toward the garage door opener so the trolley release arm snaps to
23. amage from lightning and power surges Easy to install Garage Door and Gate 956EV Keychain Remote Control Monitor Works with ALL Chamberlain openers from Monitor open closed status for 1993 present MyQ compatible With key up to 4 MyQ compatible ring garage door openers and close them from anywhere in the home Installation Upgrade Kit 940EV Wireless Keypad The Installation Upgrade Kit For use outside of the home to enable includes all components access to the garage using a 4 digit PIN needed to hang garage door A Works with ALL Chamberlain openers from openers up to 24 61 cm from 1993 present MyQ compatible the ceiling Warranty Contact Information For installation and service information call 1 800 528 9131 Before calling please have the model number of the garage door opener If you are calling about a Troubleshooting issue it is recommended that you have access to your garage door Opener while calling If you are ordering a repair part please have the following information part number part name and model number Address repair parts orders to The Chamberlain Group Inc 6050 S Country Club Road Tucson AZ 85706 CHAMBERLAIN FIVE YEAR LIMITED WARRANTY LIFETIME MOTOR AND BELT LIMITED WARRANTY The Chamberlain Group Inc Seller warrants to the first retail purchaser of this product for the residence in which this product is originally installed that it is free from defe
24. and opener ALWAYS disable locks BEFORE installing and operating the opener ONLY operate garage door opener at 120 V 60 Hz to avoid malfunction and damage 1 Disable locks and remove any ropes connected to the garage door 2 _Liftthe door halfway up Release the door If balanced it should stay in place supported entirely by its springs 3 Raise and lower the door to check for binding or sticking If your door binds sticks or is out of balance call a trained door systems Torsion Extension technician Spring Spring 4 Check the seal on the bottom of the door Any gap between the floor a and the bottom of the door must not exceed 1 4 inch 6 mm Otherwise the safety reversal system may not work properly HAH 5 The opener should be installed above the center of the door lf there is a torsion spring or center bearing plate in the way of the header bracket it may be installed within 4 feet 1 2 m to the left or right of the door center See page 12 Preparation Additional Items You May Need Tools Needed Survey your garage area to see if you will need any of the following items m 2 2X4 PIECES OF WOOD May be used to fasten the header bracket to the structural supports Also used to position the garage door opener during installation and for testing the safety reversing sensors m SUPPORT BRACKET AND FASTENING HARDWARE Must be used if you have a finished ceiling in your garage m EXTENSION BRACKETS MODEL 41A5281
25. arts Garage Door Opener Parts WD832KEV 42 Description Belt Cap Retainer Part Number 41A4371 Gear and Sprocket 41A4885 5 End Panel with Light Socket 41A7760 Light Socket 410279 Light Lens 41D7570 Capacitor 30B532 Capacitor Bracket 12A373 Travel Module 41D7742 7 10 Cover Receiver Logic Board 41A7620 8 45ACT 11 12 End Panel for Receiver Logic Board with Light Socket Motor with Travel Module 41D7638 41A7442 13 14 Line Cord Terminal Block 41B4245 41A3150 Not Shown Wire Harness Kit 41A7948 Repair Parts Description Belt Cap Retainer Part Number 41A4371 Garage Door Opener Parts HD620EV Gear and Sprocket 41A4885 5 Drive and Worm Gear 41A2817 Line Cord 41B4245 End Panel with Light Socket 41A7760 Light Socket 410279 Light Lens 41D7572 Capacitor 30B652 10 Terminal Block Motor and Travel Module 41A3150 41A7766 11 12 Travel Module Cover 41D7742 5 41A7620 4 13 14 Receiver Logic Board End Panel for Receiver Logic Board with Light Socket 45ACT 41D7638 Not Shown 2012 The Chamberlain Group Inc 114A4309E All Rights Reserved Wire Harness Kit 41A7950
26. ashes is 3 1 2 minutes 4 flashes is 4 1 2 minutes To cycle through the time intervals repeatthe step above Light Feature The lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken e Deactivate Press and hold the LIGHT button approximately 10 seconds until the garage door opener lights turn on then off again e Activate Start with the garage door opener lights on Press and hold the LIGHT button approximately 10 seconds until the garage door opener lights turn off then on again Ifthe command LED is continuously blinking the LOCK feature needs to be deactivated Operation Using the Control Panel continued LOCK The LOCK feature is designed to prevent activation of the garage door opener from remote controls while still allowing activation from the door control and keyless entry This feature is useful for added peace of mind when the home is empty i e vacation e Activate Press and hold the LOCK button for 2 seconds The command LED will flash as long as the lock feature is activated and your handheld remote control will not operate your door at this time e Deactivate Press and hold the LOCK button again for 2 seconds The command LED will stop flashing and normal operation will resume TIMER TO CLOSE DO NOT enable TTC if operating a one piece door The TTC can be turned on or off and the time interval can be adjusted to 1 5 and 10 minute intervals
27. cts in materials and or workmanship for a period of five years from the date of purchase except that the motor and belt are warranted to be free from defects in materials and or workmanship for the lifetime of the product while you own your residence The proper operation of this product is dependent on your compliance with the instructions regarding installation operation and maintenance and testing Failure to comply strictly with those instructions will void this limited warranty in its entirety If during the limited warranty period this product appears to contain a defect covered by this limited warranty call 1 800 528 9131 toll free before dismantling this product You will be advised of disassembly and shipping instructions when you call Then send the product or component pre paid and insured as directed to our service center for warranty repair Please include a brief description of the problem and a dated proof of purchase receipt with any product returned for warranty repair Products returned to Seller for warranty repair which upon receipt by Seller are confirmed to be defective and covered by this limited warranty will be repaired or replaced at Seller s sole option at no cost to you and returned pre paid Defective parts will be repaired or replaced with new or factory rebuilt parts at Seller s sole option You are responsible for any costs incurred in removing and or reinstalling the product or any component ALL IMPL
28. e door control blink Ifyou have a Smart Control Panel installed and the TTC is set to a custom time press the ON button on the Premium Motion Detecting Control Panel to set the time properly My vehicle s Homelink is not programming to my garage door opener Depending on the make model and year of your vehicle an external adapter may be required Visit www homelink com for additional information 38 Accessories 7702CB 8810CB Outside Quick Release Required for a garage with NO access door 8 Foot 2 4 m Rail Extension To allow an 8 foot 2 4 m door to open fully 10 Foot 3 m Rail Extension To allowa 10 foot 3 m door to open fully 41A5281 PILCEV CLLP1 Extension Brackets Optional For safety reversing sensor installation onto the wall or floor MyQ Remote Light Control Control home lighting and garage doors with one remote For use with plug in lamps Synchronize to work with MyQ compatible garage door openers and remote controls Laser Parking Assistant Parkin the right spot every time A laser beam is activated by your garage door opener and projected on to the dashboard of your vehicle to guide perfect parking AGDMEV BIKO1 System Surge Protector 953EV Remote Control The Garage Door Opener Works with ALL Chamberlain openers from Surge Protector is designed to 1993 present MyQ compatible Includes protect Chamberlain garage visor Clip door openers against d
29. e sensor brackets to the floor using concrete anchors not provided Slide the carriage bolt into the slot on each sensor Insert the bolt through the hole in the sensor bracket and attach with the wing nut The lenses on both sensors should point toward each other Make sure the lens is not obstructed by the sensor bracket Not provided Carriage Bolt 1 4 20x1 2 Installation STEP 14 Wire the Safety Reversing Sensors lf your garage already has wires installed for the safety reversing sensors proceed to page 25 HARDWARE Insulated Staple Not Shown OPTION A INSTALLATION WITHOUT PRE WIRING 1 Run the wire from both sensors to the garage door opener Attach the wire to the wall and ceiling with the staples 2 Strip 7 16 inch 11 mm of insulation from each set of wires Separate the wires Twist the white wires together Twist the white black wires together 3 _ Insert the white wires into the white terminal on the garage door opener Insert the white black wires into the grey terminal on the garage door opener To insert or remove the wires from the terminal push in the tab with a screwdriver tip 24 Installation STEP 14 Wire the Safety Reversing Sensors continued OPTION B PRE WIRED INSTALLATION Cut the end of the safety reversing sensor wire making sure there is enough wire to reach the pre installed wires from the wall Separate the safety reversing sensor wires and strip 7 16 inch 11 mm o
30. e sliding onto rail Emergency release rope and handle Rail 1 front and 4 center sections Hanging brackets 2 Packaged inside the front rail section Garage door opener motor unit Sprocket cover and screws U bracket Belt Door control Remote control The Protector System Safety reversing sensors with 2 conductor white and white black wire attached Sending Sensor 1 Receiving Sensor 1 and Safety Sensor Brackets 2 NOT SHOWN White and red white wire Owner s manual m T70 vozzZzr ac Preparation Hardware Inventory ASSEMBLY HARDWARE Bolt Bolt 1 4 20x1 3 4 Lock Nut 1 4 20 Lock Washer 3 8 Hex Screw Nut 3 8 8x3 8 2 packed with the sprocket cover mE INSTALLATION HARDWARE Self Threading Screw Lag Screw 5 16 9x1 5 8 1 4 14x5 8 2 Clevis Pin 5 16 x1 1 2 Wing Nut 1 4 20 2 Carriage Bolt 1 4 20x1 2 2 Lock a Nut 5 16 18 5 5 16 18 6 O DOOR CONTROL HARDWARE Screw 6 32x1 2 5 TAT site Screw 6ABx1 2 Not Shown Ring Fastener 3 Drywall Anchors 2 Assembly STEP 1 Assemble the rail and trolley ia TO MOTOR UNIT CAUTION U Bracket AE To prevent INJURY from pinching keep hands and fingers away from the joints while assembling the g Outer Trolley rail To avoid installation difficulties do not run the garage door opener until instructed to do so The front rail
31. ermit anyone to cross path E of closing garage door INTRODUCTION Compatible with MyQ enabled accessories see page 39 Your garage door opener is compatible with up to 2 MyQ door controls NOTE Older Chamberlain door controls and third party products are not 4 5 GANG BOX compatible DRYWALL Install the door control within sight of the door ata minimum height of 5 feet 1 5 m where small children cannot reach and away from the moving parts of the door For gang box installations itis not necessary to drill holes or install the drywall anchors Use the existing holes in the gang box NOTE Your product may look different than the illustrations HARDWARE Screw Screw 6 321 2 SET 648x1 2 5 TEE Drywall MI Anchors 2 MOC 20 Installation STEP 11 Wire the door control to the garage door opener HARDWARE Insulated Staple Not Shown 1 Run the white and red white wire from the door control to the garage door opener Attach the wire to the wall and ceiling with the staple not applicable for gang box or pre wired installations Do not pierce the wire with the staple as this may cause a short or an open circuit Strip 7 16 inch 11 mm ofinsulation from the end of the wire near the garage door opener 3 Connect the wire to the red and white terminals on the garage door opener If your garage is pre wired make sure you use the same wires that are connected to the door control To insert or release wire
32. ety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction Using the Motion Detecting Control Panel SYNCHRONIZE THE DOOR CONTROL To synchronize the door control to the garage door opener press the push bar until the garage door opener activates it may take up to 3 presses Test the door control by pressing the push bar each press ofthe push bar will activate the garage door opener Command LED Push Bar HOLD OPEN LEARN Button 1 5 and Button TTC 10 Minute LOCK Button TTC LED LIGHT Button Motion Sensor 33 MOTION DETECTING CONTROL PANEL FEATURES PUSH BAR Press the push bar to open or close the door LIGHTS Light Button Press the LIGHT button to turn the garage door opener lights on or off When the lights are turned on they will stay on until the LIGHT button is pressed again or until the garage door opener is activated Once the garage door opener is activated the lights will turn off after the specified period of time the factory setting is 4 1 2 minutes The LIGHT button will not control the lights when the door is in motion To change the amount of time the garage door opener lights will stay on Press and hold the LOCK button approximately 10 seconds until the garage door opener lights flash The time interval is indicated by the number times the garage door opener flashes 1 flash is 1 1 2 minutes 2 flashes is 2 1 2 minutes 3 fl
33. f insulation from each end Choose two of the pre installed wires and strip 7 16 inch 11 mm ofinsulation from each end Make sure that you choose the same color pre installed wires for each sensor Connect the pre installed wires to the sensor wires with wire nuts making sure the colors correspond for each sensor For example the white wire would connect to the yellow wire and the white black wire would connectto the purple wire Atthe garage door opener strip 7 16 inch 11 mm of insulation from each end of the wires previously chosen for the safety reversing sensors Twist the like colored wires together Insert the wires connected to the white safety sensor wires to the white terminal on the garage door opener Insert the wires that are connected to the white black safety sensor wires to the grey terminal on the garage door opener 25 1 Safety reversing sensor wires Pre installed wires Not Provided Safety reversing Pre installed wires sensor wires White White Black Yellow for example Purple for example Purple Yellow for example To insert or remove the wires from the terminal push in the tab with a screwdriver tip Installation STEP 15 Connect power A WARNING To prevent possible SERIOUS INJURY or DEATH from electrocution or fire Be sure power is NOT connected to the opener and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection Garage door insta
34. ge door opener is working properly My door will not close and the light bulbs blink on my motor unit The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction e Verify the safety sensors are properly installed aligned and free of any obstructions SOLUTION Manually open and close the door Check for binding or obstructions such as a broken spring or door lock correct as needed If the door is binding or sticking contact a trained door systems technician If door is not binding or sticking attempt to reprogram travel refer to page 28 Communication error to travel module Check travel module connections replace travel module if necessary Safety sensors are misaligned or were momentarily obstructed Realign both sensors to ensure both LEDs are steady and not flickering Make sure nothing is hanging or mounted on the door that would interrupt the sensor s path while closing My garage door opener light s will not turn off when the door is open The garage door opener is equipped with a feature that turns the light on when the safety reversing sensors have been obstructed or when the motion sensor on the door control detects movementin the garage These features can be disabled using the door control see page 33 My neighbor s remote control opens my garage door Erase the memory from your garage door opener and reprogram the remote control s The LEDs on th
35. h the rail and pulley Tighten with a 3 8 lock washer and nut underneath the rail until the lock washer is compressed Rotate the pulley to be sure it spins freely Locate the rail tab The rail tab is between the idler bolt and the trolley in the front rail section Use a flathead screwdriver and lift the rail tab until the tab is vertical 90 HARDWARE Bolt Nut 3 8 CORRECT INCORRECT Rail Tab Grease Inside Pulley She Idler Pulley Nut 3 8 Trolley Connector Assembly STEP 4 Install the belt 1 N Pull the belt around the idler pulley and toward the trolley The ribbed side must contact the pulley Hook the trolley connector into the retaining slot on the trolley a With the trolley against the screwdriver dispense the remainder of the belt along the rail toward the motor unit around the sprocket The sprocket teeth must engage the belt b Thread the inner nut and lock washer onto the trolley thread shaft c Check to make sure the beltis not twisted Insert the trolley threaded shaft through the hole in the trolley Be sure the beltis not twisted c Loosely thread the outer nut onto the trolley threaded shaft Remove the screwdriver a Trolley Connector Sprocket Lock Nut Front Rail Section Assembly STEP 5 Tighten the belt and install the sprocket cover 4 WARNING To avoid possible SERIOUS INJURY to finger from moving garage door opener e ALWAYS keep hand clea
36. he garage door opener lights will flash twice and the UP Button will begin to flash 6 Press and release the UP Button When the door travels to the programmed UP position the DOWN Button will begin to flash 7 Press and release the DOWN Button The door will travel to the programmed DOWN position Programming is complete Ifthe garage door opener lights are flashing 5 times during the steps for Program the Travel the programming has timed out If the garage door opener lights are flashing 10 times during the steps for Program the Travel the safety reversing sensors are misaligned or obstructed refer to page 28 When the sensors are aligned and unobstructed cycle the door through a complete up and down cycle using the remote control or the UP and DOWN buttons Programming is complete If you are unable to operate the door up and down repeat the steps for Programming the Travel 29 Adjustments STEP 2 Test the Safety Reversal System STEP 3 Test the Protector System amp WARNING Without a properly installed safety reversal system persons particularly small children could be 4 WARNING Without a properly installed safety reversing sensor persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door SERIOUSLY INJURED or KILLED by a closing garage door e Safety reversal system MUST be tested every month After ANY adju
37. llation and wiring MUST be in compliance with ALL local electrical and building codes NEVER use an extension cord 2 wire adapter or change plug in any way to make it fit outlet Be sure the opener is grounded To avoid installation difficulties do not activate the garage door opener at this time To reduce the risk of electric shock your garage door opener has a grounding type plug with a third grounding pin This plug will only fit into a grounding type outlet Ifthe plug doesn t fit into your outlet contact a qualified electrician to install the proper outlet 26 THERE ARE TWO OPTIONS FOR CONNECTING POWER OPTION A TYPICAL WIRING 1 Plug in the garage door opener into a grounded outlet 2 DO NOT run garage door opener at this time OPTION B PERMANENT WIRING If permanent wiring is required by your local code refer to the following procedure To make a permanent connection through the 7 8 inch hole in the top of the motor unit according to local code 1 Remove the motor unit cover screws and set the cover aside 2 Remove the attached 3 prong cord 3 Connect the black line wire to the screw on the brass terminal the white neutral wire to the screw on the silver terminal and the ground wire to the green ground screw The opener must be grounded 4 Reinstall the cover Green Installation STEP 16 Ensure the safety reversing sensors are aligned The door will not close if the sensors have not been
38. n both sensors should point toward each other Make sure the lens is not obstructed by the sensor bracket No more than 6 inches 15 cm Carriage Bolt 1 4 20x1 2 Installation STEP 13 Install the Protector System continued OPTION B WALL INSTALLATION lf additional clearance is needed an extension bracket not provided or wood blocks can be used Make sure each bracket has the same amount of clearance so they will align correctly 1 2 3 Position the sensor bracket against the wall with the curved arms facing the door Make sure there is enough clearance for the beam to be unobstructed Mark holes Drill 3 16 inch pilot holes for each sensor bracket and attach the sensor brackets to the wall using lag screws not provided Slide the carriage bolt into the slot on each sensor Insert the bolt through the hole in the sensor bracket and attach with the wing nut The lenses on both sensors should point toward each other Make sure the lens is not obstructed by the sensor bracket 2 Not provided Not provided No more than PA PF 6 inches 15 cm 23 4 Wing Nut i 1 4 20 Carriage Bolt 1 4 20x1 2 23 OPTION C FLOOR INSTALLATION Use an extension bracket not provided or wood block to raise the sensor bracket if needed 1 Carefully measure the position of both sensor brackets so they will be the same distance from the wall and unobstructed Attach th
39. ncandescent A19 light bulb 100 watt maximum or for maximum energy efficiency a 26W 100W equivalent compact fluorescent light CFL bulb may be used NOTE Do not use halogen short neck or specialty light bulbs as these may overheat the end panel or light socket Do not use LED bulbs as they may reduce the range or performance of your remote controls Light Feature The garage door opener is equipped with an added feature the lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken For added control over the light bulbs on your garage door opener see page 33 Operation Using your Garage Door Opener The garage door opener can be activated through a wall mounted door control remote control wireless keyless entry or MyQ accessory When the door is closed and the garage door opener is activated the door will open Ifthe door senses an obstruction or is interrupted while opening the door will stop When the door is in any position other than closed and the garage door opener is activated the door will close Ifthe garage door opener senses an obstruction while closing the door will reverse Ifthe obstruction interrupts the sensor beam the garage door opener lights will blink 10 times However you can close the door if you hold the button on the door control or keyless entry until the door is fully closed The safety reversing sensors do not affect the opening cycle The saf
40. o ensure both hing is hanging or mounted on the door that would ing or obstructions such as a broken spring or door lock correct as needed Check wiring connections at travel module and at the logic board Replace travel module if necessary Manually open and close the door Check for bind Manually open and close the door Check for bind ing or obstructions such as a broken spring or door lock correct as needed Replace logic board if necessary ing or obstructions such as a broken spring or door lock correct as needed Replace motor if necessary Program travel to coasting position or have door balanced by a trained door systems technician Replace logic board Check travel module for proper assembly replace 37 if necessary Troubleshooting DIAGNOSTIC CODE SYMPTOM Up Arrow Down Arrow Flash es Flash es 4 1 4 Door is moving stops or reverses 4 5 Opener runs approximately 6 8 stops and reverses 4 6 The garage door opener will not close and the light bulbs flash The garage door opener can beep for several reasons e Garage door opener has been activated through a device or feature such as Timer to Close or garage door monitor see page 32 My remote control will not activate the garage door e Verify the lock feature is not activated on the door control e Reprogram the remote control e Ifthe remote control will still not activate the door check the diagnostic codes to ensure the gara
41. object or a 2x4 laid flat on the floor Failure to adjust the garage door opener properly increases the risk of SEVERE INJURY or DEATH ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED see page 2 An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH ALL repairs to cables spring assemblies and other hardware ALL of which are under EXTREME tension MUST be made by a trained door systems technician ALWAYS disconnect electric power to garage door opener BEFORE making ANY repairs or removing covers This operator system is equipped with an unattended operation feature The door could move unexpectedly NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR DO NOT enable the Timer to Close functionality if operating either one piece or swinging garage doors To be enabled ONLY when operating a sectional door SAVE THESE INSTRUCTIONS Operation Features Your garage door opener is equipped with features to provide you with greater control over your garage door operation Alert2Close The Alert2Close feature provides a visual and an audible alert that an unattended door is closing TIMER TO CLOSE TTC The Timer to Close feature automatically closes the door after a specified time period that can be adjusted using the door control DO NOT enable TTC if operating a one piece door TTC is to be used ONLY with sectional doors Factory default is set to off The garage door opener will beep and the lights
42. omelink you may require an external adapter depending on the make model and year of your vehicle Visit www homelink com for additional information TO ADD REPROGRAM OR CHANGE A REMOTE CONTROL KEYLESS ENTRY PIN USING THE MOTION DETECTING CONTROL PANEL 1 Press the LEARN button on the door control to enter Programming Mode 2 Press the LEARN button again the LED will flash once 3 Remote Control Press the button on the remote control that you wish to operate your garage door Keyless Entry Enter a 4 digit personal identification number PIN of your choice on the keyless entry keypad Then press the ENTER button The garage door opener lights will flash or two clicks will be heard when the code has been programmed Repeat the steps for programming additional remote controls or keyless entry devices 2 The command LED will flash once again 1 The command LED will flash once Operation Remote Control continued PROGRAM A REMOTE CONTROL USING THE LEARN BUTTON 1 Locate the Learn Button 2 Press and immediately release the Learn button The Learn LED will glow steady for 30 seconds Within 30 seconds 3 Press and hold the button on the remote control that you wish to use Release the button when the garage door opener lights blink or two clicks are heard When replacing the light lens cover ensure the antenna wires are hanging straight down LEARN Button LEARN LED To Erase the Memory ERASE ALL REMO
43. on Adjustment Button DOWN Button To watch a short instructional video on how to program the travel on your new garage door opener use your smartphone to read the QR Code Adjustments STEP 1 Program the Travel yE PROGRAMMING BUTTONS amp WARNING Without a properly installed safety reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door UP Button Adjustment Button DOWN Button e Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system e After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 3 8 cm high object or 2x4 laid flat on floor 1 Press and hold the Adjustment Button until the UP Button begins to flash and or a beep is heard 2 Press and hold the UP Button until the door is in the desired UP position NOTE The UP and DOWN Buttons can be used to move the door up and down as needed 3 Once the door is in the desired UP position press and release the Adjustment Button The garage door opener lights will flash twice and the DOWN Button will begin to flash 4 Press and hold the DOWN Button until the door is in the desired DOWN position NOTE The UP and DOWN Buttons can be used to move the door up and down as needed 5 Once the door is in the desired DOWN position press and release the Adjustment Button T
44. ooting Your garage door opener is programmed with self diagnostic capabilities The UP and DOWN arrows on the garage door opener flash the diagnostic codes Diagnostic Chart DIAGNOSTIC CODE Up Arrow Down Arrow Flash es Flash es 1 1 1 2 1 3 1 4 1 5 1 6 2 1 5 3 2 SYMPTOM The garage door opener will not close and the light bulbs flash The garage door opener will not close and the light bulbs flash The door control will not function The garage door opener will not close and the light bulbs flash Door moves 6 8 stops or reverses No movement only a single click Opener hums for 1 2 seconds no movement Door coasts after ithas come to a complete stop No movement or sound Unable to set the travel or retain position SOLUTION Safety sensors are not installed connected or wir disconnected or cut wire es may be cut Inspect sensor wires for a There is a short or reversed wire for the safety sensors Inspect safety sensor wire atall staple and connection points replace wire or correct as needed The wires for the door control are shorted or the door control is faulty Inspect safety sensor wire at all staple points and connection points and replace wire or correct as needed LEDs are steady and not flickering Make sure not interrupt the sensor s path while closing Manually open and close the door Check for bind Safety sensors are misaligned or were momentarily obstructed Realign both sensors t
45. or Controls Keyless Entries 32 THE PROTECTOR SYSTEM SAFETY REVERSING SENSORS When properly connected and aligned the safety reversing sensors will detect an obstruction in the path of the infrared beam If an obstruction breaks the infrared beam while the door is closing the door will stop and reverse to full open position and the opener lights will flash 10 times Ifthe door is fully open and the safety reversing sensors are not installed or are misaligned the door will not close froma remote control However you can close the door if you hold the button on the door control or keyless entry until the door is fully closed The safety reversing sensors do not effect the opening cycle ENERGY CONSERVATION For energy efficiency the garage door opener will enter sleep mode when the door is fully closed The sleep mode shuts the garage door opener down until activated The sleep mode is sequenced with the garage door opener light bulb as the light bulb turns off the sensor LEDs will turn off and whenever the garage door opener lights turn on the sensor LEDs will light The garage door opener will not go into the sleep mode until the garage door opener has completed 5 cycles upon power up LIGHTS The garage door opener light bulbs will turn on when the opener is initially plugged in power is restored after interruption or when the garage door opener is activated The lights will turn off automatically after 4 1 2 minutes An i
46. or DEATH Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling otherwise garage door might NOT reverse when required DO NOT install header bracket over Vertical Centerline of Garage Door FOR HEADER BRACKET Structural Supports drywall Concrete anchors MUST be used if mounting header bracket or 2x4 into masonry NEVER try to loosen move or adjust garage door springs cables pulleys brackets or their hardware ALL of which are under EXTREME tension ALWAYS call a trained door systems technician if garage door binds sticks or is out of balance An unbalanced garage door might NOT reverse when required Header Wall N Header Wall E 2 5 cm p 2 5 cm Installation procedures vary according to garage door types Follow the instructions which apply to your Track Fak door Highest Point Highest 1 Close the door and mark the inside vertical centerline of the garage door of Travel ed p 2 Extend the line onto the header wall above the door Door ee You can fasten the header bracket within 4 feet 1 22 m of the left or right of the door center only if a torsion spring or center bearing plate is in the way or you can attach it to the ceiling when clearance is minimal It may be mounted on the wall upside down if Sectional door with curved track One piece door with horizontal track necessary to gain approximately 1 2 1 cm
47. pener does not require a itiona express ment approuve parla partie responsablede la conformit peut avoir pour r sultat d annulerlautorit de lutiisateurde faire lubrication Do not grease the door tracks fonctionnerl quipement Cet appareilest conforme aux dispositions de la partie 15 du reglementde la FCC et de Inorme IC RSS 210 Son utilisation est assujettie auxdeuxconditoins suivantes 1 ce dispositif ne peut causer desinterf rencesnuisibles et 2 ce dispositif doit accepter The Remote Control Battery toute interf rence recue ycomprisune interf rence pouvant causer un fonctionnementnon souhait Cet appareilnumerique de la classe Best conforme a la norme NMB 003 du Canada To prevent possible SERIOUS INJURY or DEATH e NEVER allow small children near batteries e If battery is swallowed immediately notify doctor To reduce risk of fire explosion or chemical burn e Replace ONLY with 3V2032 coin batteries e DO NOT recharge disassemble heat above 212 F 100 C or incinerate The 3V2032 lithium battery should produce power for up to 5 years If the battery is low the remote control s LED will not flash when the button is pressed gt O To replace battery pry open the case first in the middle 1 then at 2 3 each side 2 and 3 with the visor clip Replace the batteries with only 3V2032 coin cell batteries Insert 1 battery positive side up Dispose of old batteries properly 2 ID 36 Troublesh
48. r of sprocket while operating opener e Securely attach sprocket cover BEFORE operating 1 Spin the inner nut and lock washer down the trolley threaded shaft away from the trolley 2 To tighten the belt turn outer nutin the direction shown until the line on the spring retainer plate is visible Be sure the beltis not twisted and the ribbed side faces the rail 3 Tighten the inner nut to secure the adjustment This sets the spring to optimum belt tension 4 Position the sprocket cover over the sprocket as shown and fasten to the mounting plate with 8x3 8 hex screws provided You have now finished assembling your garage door opener Please read the following warnings before proceeding to the installation section HARDWARE Hex Screw 8x3 8 Packed with the sprocket cover 000000 Outer Nut Spring Retainer Inner Nut Lock Washer omer CTA MLE Line Qa ELE g Hex Screw 8x3 8 Installation IMPORTANT INSTALLATION INSTRUCTIONS A amp WARNING To reduce the risk of SEVERE INJURY or DEATH READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS Install garage door opener ONLY on properly balanced and lubricated garage door An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH ALL repairs to cables spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing opener Disable ALL locks and
49. reparation Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided itis installed operated maintained and tested in strict accordance with the instructions and warnings contained in this manual When you see these Safety Symbols and Signal Words on the following pages they will alert you to the possibility of serious injury or deathif you do not comply with the warnings that accompany them The hazard may come from something mechanical or from electric shock Read the warnings carefully 4 WARNING Mechanical A WARNING Electrical When you see this Signal Word on the following pages it will alert you to the possibility of damage to your garage door and or the garage door opener if you do not comply with the cautionary statements that accompany it Read them carefully CAUTION Check the Door 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH ALWAYS call a trained door systems technician if garage door binds sticks or is out of balance An unbalanced garage door may NOT reverse when required NEVER try to loosen move or adjust garage door door springs cables pulleys brackets or their hardware ALL of which are under EXTREME tension Disable ALL locks and remove ALL ropes connected to garage door BEFORE installation and operating garage door opener to avoid entanglement CAUTION To prevent damage to garage door
50. reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door e Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system e After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 3 8 cm high object or 2x4 laid flat on floor CAUTION To prevent damage to vehicles be sure fully open door provides adequate clearance Your garage door opener is designed with electronic controls to make setup and adjustments easy The adjustments allow you to program where the door will stop in the open UP and close DOWN position The electronic controls sense the amount of force required to open and close the door The force is adjusted automatically when you program the travel If anything interferes with the door s upward travel it will stop If anything interferes with the door s downward travel it will reverse 28 One Piece Doors Only When setting the UP travel for a one piece door ensure that the door does not slant backwards when fully open UP If the door is slanted backwards this will cause unnecessary bucking and or jerking when the door is opening or closing INCORRECT Programming Buttons The programming buttons are located on the left side panel of the garage door opener and are used to program the travel PROGRAMMING BUTTONS UP Butt
51. rtical set of bracket holes Drill 3 16 pilot holes and fasten the bracket securely to a structural support with the hardware provided 2x4 Structural Support Horizontal Line Z Optional Mounting Holes Header Wall Highest Point of Garage e Door Travel Vertical Centerline of Garage Door Lag Screw 5 16 9x1 5 8 Door Spring Garage Door 12 iF 2 OPTION B CEILING INSTALLATION Extend the vertical centerline onto the ceiling as shown Center the bracket on the vertical mark no more than 6 15 cm from the wall Make sure the arrow is pointing away from the wall The bracket can be mounted flush against the ceiling when clearance is minimal with the hardware provided Ceiling Mounting D 6 15 cm Maximum Door Spring Mark the side holes Drill 3 16 pilot holes and fasten bracket securely to a structural support Vertical Centerline of Garage Door Lag Screw 5 16 9x1 5 8 Header Wall Garage Door Installation STEP 3 Attach the rail to the header bracket STEP 4 Position the garage door opener 1 Align the rail with the header bracket Insert the clevis pin through the holes in the header bracket and rail Secure with the ring fastener CAUTION NOTE Use the packing material as a protective base for the garage door opener To prevent damage to garage door rest garage door opener rail on 2x4 placed on top section of HARDWARE door
52. s from the terminal push in the tab with screwdriver tip P 7 16 11 mm l 21 STEP 12 Attach the warning labels 1 Attach the entrapment warning label on the wall near the door control with tacks or staples 2 Attach the manual release safety reverse test label in a visible location on the inside of the garage door Installation STEP 13 Install the Protector System 4 WARNING Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor To prevent SERIOUS INJURY or DEATH from closing garage door e Correctly connect and align the safety reversing sensor This required safety device MUST NOT be disabled e Install the safety reversing sensor so beam is NO HIGHER than 6 15 cm above garage floor IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSORS The safety reversing sensors must be connected and aligned correctly before the garage door opener will move in the down direction The sending sensor with an amber LED transmits an invisible light beam to the receiving sensor with a green LED lf an obstruction breaks the light beam while the door is closing the door will stop and reverse to the full open position and the garage door opener lights will flash 10 times NOTE For energy efficiency the garage door opener will enter sleep mode when the door is fully closed The sleep mode shuts the garage door opener down until activated The sleep mode is seq
53. stments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 3 8 cm high object or 2x4 laid flat on the floor 1 Open the door Place the garage door opener carton in the path of the door 2 Press the remote control push button to close the door The door will not move more than an inch 2 5 cm and the garage door opener lights will flash 10 times 1 With the door fully open place a 1 1 2 inch 3 8 cm board or a 2x4 laid flat on the floor The garage door opener will not close from a remote control if the LED in either safety reversing sensor centered under the garage door is off alerting you to the fact that the sensor is misaligned or obstructed If the garage door opener 2 Press the remote control push button to close the door The door MUST reverse when itmakes closes the door when the safety reversing sensor is obstructed and the sensors are no more than 6 contact with the board inches 15 cm above the floor call for a trained door systems technician Ifthe door stops and does not reverse on the obstruction the down travel needs to be increased refer to Adjustment Step 1 Repeat the test When the door reverses upon contact with the 1 1 2 inch board remove the board and open close the door 3 or 4 times to test the adjustment Ifthe garage door opener continues to fail the safety reversal test call a trained door systems technician 1 2
54. uenced with the garage door opener light bulb as the light bulb turns off the sensor LEDs will turn off and whenever the garage door opener lights turn on the sensor LEDs will light The garage door opener will not go into the sleep mode until the garage door opener has completed 5 cycles upon power up NOTE When installing the safety reversing sensors check the following e Sensors are installed inside the garage one on either side of the door e Sensors are facing each other with the lenses aligned and receiving sensor lens does not receive direct sunlight e Sensors are no more than 6 inches 15 cm above the floor and the light beam is unobstructed Safety Reversing Sensor Invisible Light Beam 6 15 cm max above floor Protection Area 22 HARDWARE Carriage Bolt Wing Nut 1 4 20x1 2 in 1 4 20 The safety reversing sensors can be attached to the door track the wall or the floor The sensors should be no more than 6 inches 15 cm above the floor Ifthe door track will not support the sensor bracket a wall installation is recommended Choose one of the following installations OPTION A DOOR TRACK INSTALLATION 1 Slide the curved arms of the sensor bracket around the edge of the door track Snap into place so that the sensor bracketis flush against the track 2 Slide the carriage bolt into the slot on each sensor 3 Insertthe bolt through the hole in the sensor bracket and attach with the wing nut The lenses o
55. wood doors A horizontal and vertical reinforcementis needed for FIGURE 1 FIGURE 2 Vertical FIGURE 3 Vertical Reinforcement lightweight garage doors fiberglass aluminum steel Reinforcement doors with glass panel etc not provided Vertical Centerline Vertical Centerline of Garage Door A horizontal reinforcement brace should be long of Garage Door enough to be secured to two or three vertical supports Bolt 5 16 18x2 A vertical reinforcement brace should cover the height not provided of the top panel UP HARDWARE Door Bracket FK Sp micelle l Self Threading Screw gt Lock Washer 5 6 ae Screw 1 4 14x5 8 Nut 5 16 18 FIGURE 5 Reinforcement Board Vertical Inside Edge of Door o Gantarling Bolt 5 16 18x2 idan ioe of Garage not provided OPTION A SECTIONAL DOORS sl 1 Center the door bracket on the previously marked vertical centerline used for the header bracket installation Note correct UP placement as stamped inside the bracket UP 2 Position the top edge of the bracket 2 4 5 10 cm below the top edge of the door OR Self Threading directly below any structural support across the top of the door Screw Vertical Centerline of 3 Mark drill holes and install as follows depending on your door s construction 1 4 14x5 8 Garage Door E D 16 Installation STEP 8 Install the door bracket continued Header Wall a N OPTION B ONE PIECE DOORS 2x4 Support Finished Ceiling
Download Pdf Manuals
Related Search