Power Pro Technology 22020 Use and Care Manual
Contents
1. 2 Gallon Oll Free Air Compressor Item 22020 Owner s Manual DO NOT RETURN TO GALLON STORE HEE Questions Problems Please call our customer help line 800 232 1195 M F 8 5 CST Or by email partsandservice greatlakestec com TABLE OF CONTENTS Technical Dadaan Asha NASAAN basa 2 Packase COMMENTS nn E ele hide 2 Rules for Sale Operations ease veo ee pa abide t oa on dent 3 General Instructions for All Power Tools 4 Specific safety Rules and Precautions 7 Assembly INSIUCTIONS aos cin uU ne du oua bd de Pda E nA E 8 Operate TOS EEUCHODS s sian ANG ralliement 8 Inspection Maintenance and Cleaning 10 Troubles IO OMNIS AA AA Rusa 11 PAS IS Re NN ae beanie ANNA nama 12 Parts AA nl 13 WV ATARI NAE ANA ati need ions 14 Technical Data 1 3 HP 2 Gal Oil Free Air Compressor Model Number Volts Amperage Power Cord Type Power Plug Type Pressure Switch Type Arr Inlet Fuse Compressor Style Pump Style Maximum Air Pressure Air Flow Air Tank Capacity Weight Package Contents 1 Air Compressor Coil Air Hose 1 4 x 25 1 Blow Gun 22020 120V 2 6A 18 AWG 6 ft Length 3 Prong Grounded ON OFF Switch 1 4 18 NPT Female Thread 3A Oil Free Single Cylinder 100 PSI 0 6CFM 90PSI 1 0CFM 40PSI 2 Gallons 15 5 Lbs 1 Female Universal Quick Connect 12. Use sealing tape for best air tight connections Operating Instructions To Start The Compressor 1 Check to make sure the Air Tank s Drain Valve 54 located at the bottom of the Air Tank 53 is fully closed Pull on the Safety Valve 25 to verify that it is not stuck See Figure B and C Figure B Safety Valve 25 zm L ES Nm NO Drain Valve 54 ON OFF Power Switch 45 2 Plug the Power Cord 35 into the nearest 120 volt grounded electrical outlet 3 Push in the ON side of the ON OFF Power Switch 45 to turn the compressor on See Figure B Figure C Gauge 26 Regulated Pressure Gauge 70 Safety Valve 25 Pressure Regulator 24 2 Figure C To Adjust The Air Regulator 1 With the supplied air flow valve attached to the Pressure Regulator 24 and the valve handle in the OFF position handle perpendicular to the outlet pipe turn the compressor on When the maximum air pressure 100 PSI is reached as indicated by the Tank Pressure Gauge 26 the motor will stop 2 Turn the Pressure Regulator 24 knob to adjust Pressure Regulator 24 Turn the Pressure Regulator 24 knob counterclockwise to decrease the PSI turn it clockwise to increase the PSI When the Regulated Pressure Gauge 70 shows the pressure that you want to limit the compressor to the Pressure Regulator 24 is set See Figure C 3 Between the Pressure Regulator knob and valve body
3. a narrow ring acts as a lock ring for the knob Rotate the ring in a counterclockwise direction and tighten it against the knob to secure the setting See Figure C 4 Attach hose to air flow valve then tool to hose turn on air flow valve to supply air pressure shown on gauge 70 to tool NOTE When the maximum air pressure 100 PSI is reached as indicated by the Tank Pressure Gauge 26 the motor will stop The Compressor will automatically restart when the air pressure drops below 85 PSI See Figure C To Stop The Compressor l pa Push the ON OFF Power Switch 45 to its OFF position Turn air flow valve to off handle perpendicular to outlet pipe Press trigger on tool to relieve air pressure in hose Disconnect hose from air flow valve Relieve the Air Tank pressure and remove moisture by opening the Tank Drain Valve 54 Turn the valve slowly counter clockwise until the pressure is relieved Then retighten the Drain Valve 54 See Figure B Allow the Air Compressor to completely cool Then store the unit in a clean dry safe location out of reach of children Inspection Maintenance and Cleaning l WARNING Make sure the ON OFF Power Switch 45 of the Air Compressor is in its OFF position the unit is unplugged from its electrical outlet and air is drained from the Tank 53 before performing any inspection maintenance or cleaning procedures or leaving it unattended Before each use ins
4. keep clean Check for broken parts or binding of moving parts before use If damaged have the tool serviced before use Prevent accidents caused by poorly maintained tools e Use only accessories recommended for your model Accessories suitable for one tool may become hazardous when used on another tool SERVICE e Tool service mechanical and or electrical is to be performed only by qualified repair personnel Service performed by unqualified personnel may result in a risk of injury e When servicing a tool use only identical replacement parts Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electrical shock or injury NOTE if any parts are damaged or missing do not attempt to plug in the power cord and turn the switch on until the damaged or missing parts are obtained and are installed correctly Specific Safety Rules and Precautions 1 10 11 12 13 14 15 16 17 18 CAUTION Your Warranty is voided if You drop the Air Compressor Always lift the Air Compressor using its Handle Do not expose to a high dust environment Dusty conditions may increase wear on the Compressor DANGER This Air Compressor is NOT designed for and should not be used to supply breathing air DANGER Never attempt to repair or modify the Air Tank 53 Welding drilling or any other modification will weaken the Tank resulting in damage from rupture or explosion Always replace worn
5. the cord 1s rated for outdoor use even 1f your application is indoors Outdoor use cords have the letters WA on the cord jacket ALL GROUNDED CORD CONNECTED TOOLS In the event of a malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electrical shock Tools equipped with an electric cord having an equipment grounding conductor must be plugged into a matching outlet that 1s properly installed and grounded in accordance with all local codes and ordinances Do not modify the plug provided in any way If the plug dose not fit the outlet have the proper outlet installed by a qualified electrician The use of any Extension Cord will cause some loss of power To keep this to a minimum and to prevent overheating and motor burn out use the table below to determine the minimum wire size A W G Extension Cord Use only 3 wire extension cords that have 3 prong grounding plugs and 3 pole receptacles that accept the tool s plug AMERICAN WIRE GAUGE RATING CHART EXTENSION CORD 25 50 1 100 125 150 175 200 LENGTH FEET AMPS AWG wire gauge 0 to 10 0 18 18 16 16 10 1 to 13 0 16 16 14 14 13 1 to 15 14 12 12 12 15 1 to 18 14 12 12 12 Use only UL approved extension cord Repair or replace cords as soon as damage occurs Never use a damaged cord Cover of Grounded a Outlet Box M Grounding Pin A Adapter Grounding Means D Figure Wiring M
6. 4 l Air Chuck 1 Thread Seal Tape 1 Blow Gun Tapered Nozzle 1 Blow Gun Adapter 1 Inflation Needle 1 Air Flow Valve 1 Female Connector 1 4 Rules for Safe Operation The purpose of safety symbols is to attract your attention to possible dangers The safety symbols and the explanations with them deserve your careful attention and understanding The safety warnings do not by themselves eliminate any danger The instructions or warnings they give are not substitutes for proper accident prevention measures Symbol Meaning A Safety Alert Symbol Indicates danger warning or caution may be used in conjunction with other symbols or pictographs Always follow the safety precautions to reduce the risk of fire electric shock and personal injury Note Advises you of information or instructions vital to the operation or maintenance of the equipment IMPORTANT Servicing requires extreme care and knowledge and should be performed only by a qualified service technician For service call our customer help line at 800 232 1195 M F 8 5 CST When servicing use only genuine PowerPro Technology replacement parts A WARNING Do not attempt to operate this tool until you have read thoroughly and understand completely all instructions safety rules etc contained in this manual Failure to comply can result in accidents involving fire electric shock or serious personal injury Save this operator s manual and review frequently for c
7. ade without charge for parts or labor Parts replaced during warranty repairs will be considered as part of the original product and will have the same warranty period as the original product TO EXERCISE WARRANTY COVERAGE Do not return to retailer For warranty and technical support call the toll free Customer Service Number 800 232 1195 and you will be informed of the nearest authorized service center or where to ship the unit for repair We will prearrange the repair with the repair center should that be the procedure for this particular compressor WARRANTY COVERAGE This warranty 1s conveyed to the original purchaser and is not transferable Warranty does not extend to air compressors damaged or affected by accidents neglect misuse unauthorized alterations use in applications beyond product design and any other modification or abuse PowerPro Technology is not liable for any indirect incidental or consequential damages from the sale or use of this product Any implied warranties are limited to one 1 year as stated in this written limited warranty Some states do not allow limitation on the length of an implied warranty Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you the specific legal right and you may have other rights that vary by state 14
8. cracked or damaged Tanks WARNING Use only air hose with minimum rating of 150 PSI Make sure all tools and equipment used with the Air Compressor are rated to the appropriate capacity Do not use any tool or equipment that operates above 100 PSI Drain the Air Compressor every day Do not allow excessive moisture to build up inside the Air Compressor s Tank Do not open the Drain Valve 54 with more than 10 PSI of air pressure in the Tank Do not unscrew the Drain Valve so that more than four threads are showing Do not alter or remove the Safety Valve 25 Make sure the Air Compressor 1s located on a flat level sturdy surface capable of supporting the weight of the Compressor operator s and any additional tools and equipment Do not move or transport the Compressor if the Air Tank 53 is under pressure Industrial applications must follow OSHA guidelines Never stand on the Air Compressor Serious injury could result if the Compressor is tipped Never leave the Air Compressor unattended when it is plugged in and running Turn off the Compressor and unplug the unit before leaving Do not allow children and other unauthorized people to handle or play with the Air Compressor Do not modify the factory set pressure shutoff or startup switches This tool will do the work better and safer at the speed and capacity for which it was designed Avoid body contact with oils and lubricants used in the Compressor If swallowed seek m
9. edical treatment immediately For skin contact immediately wash with soap and water For eye contact immediately flush eyes with clean water People with pacemakers should consult their physician s before use Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure WARNING The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Assembly Instructions CAUTION Always make sure the Compressor s Power Switch 45 is in its OFF position prior to performing any service maintenance or cleaning of the Compressor 1 Handle is shipped partially attached Remove screw 46 and position handle as shown in figure A Re install screw 46 and tighten securely 2 Install air flow valve in pressure regulator 24 Note Use sealing tape or silicon thread compound on air flow valve threads to prevent air leaking Connect the 4 female connector to the air flow valve Remember to use the sealing tape Handle 47 Pressure Regulator 24 Screw 46 Figure A HOSE CONNECTION 1 Attach an air hose to the compressor s air outlet air flow valve with the 14 female connector already attached Connect the air hose to the air inlet of the tool
10. ethods Tools with three wire grounding plugs that look like the plug illustrated in Sketch A in Figure are intended for use on a circuit that has an outlet that look like the one illustrated in Sketch A in Figure A temporary adapter which looks like the one illustrated 1n Sketches B and C may be used to connect this plug to a 2 pole receptacle as shown in Sketch B if a properly grounded outlet is not available The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician The green colored rigid ear lug etc extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box PERSONAL SAFETY e Dress appropriately Do not wear loose clothing or jewelry Keep long hair in place and contained Keep clothing hair and gloves away from moving parts Loose clothing jewelry and hair can be snagged in moving parts e Use common sense stay alert and watch what you are doing while operating a power tool Do not use tools while under the influence of alcohol medication or drugs Keep focused on the work at hand while using a power tool to prevent personal injury e Make sure the power switch is in the OFF position before plugging it into the receptacle This will prevent accidental starting Carrying tools with your finger on the switch or plugging in the tools with the switch in the ON position invites accidents e Remove adjusting tool
11. fective pressure switch Immediately unplug compressor from turn off compressor at its electrical outlet Do not operate 100PSI compressor until a qualified service technician can replace pressure switch 11 Part List 1 Motor 1 36 Motor Cover 1 3 Screw 1 38 Screw M4 x 8 2 4 Bearing 608 2RS 1 39 Washer 1 6 Silica Gel Ring 12X25 41 Screw M4X19 8 PaperPad 483 Fuse Amp 9 Hop a FuseBox J l 11 Cylinder Washer 1 46 Screw M5 x 16 2 Flat Washer Safety Valve Screw M3 x 6 62 Screw M6 x 20 Copper Connector Rod Female Nipple 14 fh 555 EEE 60 12 Parts Diagram WARRANTY STATEMENT FOR POWERPRO TECHNOLOGY PRODUCTS PowerPro Technology air compressors are warranted to the original purchaser to be free from defects in materials and workmanship for a period of one 1 year from the date of original purchase Air compressors used for commercial or for rental have a warranty period of 90 days from date of original purchase Please fill out the enclosed warranty card 1f applicable and mail it to Power Pro Technology along with a copy of the receipt The information 1s required to process warranty claims PowerPro Technology will repair or replace at its discretion any part that is proven to be defective in materials or workmanship under normal use during the one 1 year warranty period Warranty repairs or replacements will be m
12. ontinuing safe operation and instructing others who may use this tool Safe operation of this power tool requires that you read and understand this operator s manual and all labels affixed to the tool Safety 1s a combination of common sense staying alert and knowing how your tool works General Instructions for All Power Tools READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electrical shock fire and or serious personal injury WORK AREA Keep your work area clear and well lit Cluttered work surfaces and dark areas invite accidents Keep people not involved in the work especially children away from the work area while operating a power tool Distractions can cause you to lose control of the tool Do not operate power tools in an unsafe environment such as explosive atmosphere flammable liquids gases and dust A spark created by a power tool may ignite the fumes or dust ELECTRICAL SAFETY Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances Never remove the grounding prong or modify the plug in any way Do not use any adapter plug Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded If the tool should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user Avoid body contact with grounded su
13. pect the general condition of the Air Compressor Check for loose screws misalignment or binding of moving parts cracked or broken parts damaged electrical wiring loose air fittings and any other condition that may affect the safe operation of the Compressor If abnormal noise or vibration occurs have the problem corrected before further use Do not use damaged equipment Daily purge the Air Tank 53 of all air and moisture to prevent corrosion To do so slowly and carefully unscrew no more than four threads the Tank Drain Valve 54 until the compressed air and condensation begins to be released from the Tanks Allow sufficient time for all of the air and condensation to escape from the Tanks Then firmly re tighten the Drain Valve CAUTION All maintenance service or repairs not mentioned in this manual must only be performed by a qualified service technician To replace the Fuse 43 unscrew the fuse and replace with a 250V 3A fuse 10 Troubleshooting Replace fuse Compressor will not Loose electrical connections Make sure compressor 1s plugged into Start a working 120 volt grounded electrical outlet Defective pressure switch Have a qualified service technician Lo esu 56 replace pressure switch 56 Air leak in safety valve Replace safety valve Drain valve not fully closed Close drain valve Safety valve releasing Defective safety valve Replace safety valve Pressure switch will not De
14. rfaces such as radiators pipes ranges and refrigerators There is an increased risk of electrical shock if your body is grounded Do not operate power tools in the rain or wet conditions Water entering a power tool increases the risk of electrical shock Do not stress the power cord Never carry the power tool by the cord or disconnect the plug from the receptacle by yanking on the cord Keep cord away from sharp edges heat solvents and oil Replace damaged cord immediately Damaged cords increase the risk of electrical shock Use outdoor extension cords when operating the power tool outside Outdoor power cords are marked W A or W and are rated for outdoor use These cords reduce the risk of electrical shock GROUNDING INSTRUCTIONS Your compressor has a grounded three prong plug If using an extension cord it must be a three prong type You must connect to a three prong receptacle only The third prong 1s for grounding do not remove or disable the third prong as this will create an unsafe condition Common household current is 110 120 volts As long as your compressor is rated from 110 120 volts there will be no complications in using power from a household receptacle Never try to plug a tool designed for 110 120 Volts into a 220 240 Volt receptacle 220V plugs and outlets are shaped differently to prevent this Only use rounded jacket extension cords preferably listed by Underwriter s Laboratories UL Make sure
15. s such as wrenches or keys before turning the tool on A wrench or key left attached to a rotating part will fly off and may cause personal injury e Do not overreach while operating a power tool Keep proper footing and balance at all times Good balance and solid footing enables better control in unexpected situations e Always wear appropriate safety equipment Always wear eye protection while operating a power tool Use appropriate dust respirators hearing protection hard hat face shield or safety shoes as dictated by the work and tool TOOL USE AND CARE e Secure the work piece with clamps or other practical methods to provide a secure work platform Holding the work by hand or against your body is not secure and may lead to loss of control e Use the correct tool for the work The proper tool will do the work faster and safer e Do not use the tool if the ON OFF switch is not working Operating a tool that cannot be controlled by you is dangerous and must be repaired before use e Always disconnect the power cord from the electrical outlet before storing the tool making adjustments or adding replacing accessories This simple prevention will reduce the risk of accidental starting the tool e Store the tool in a secure place out of reach of children A secure storage location will prevent the unauthorized use by untrained users e Properly maintain tools Keep all cutting tools sharp and clean Remove contaminants from the tool and
Download Pdf Manuals
Related Search