Waekon 76760 Use and Care Manual
Contents
1. e Ifthe tester resets or changes mode during testing the spark plug may not be firing and the high voltage is approaching the os maximum output voltage Quick Check Mode To enter the Quick Check Mode simply turn the tester oRgPhe tester automatically enters this mode when it is po n During this mode the red and green LEDs a y flash o lights to show the polarity second until a spark is detected Once a spark is detected the eaa affs and QD green LED Notes 4 Q Ifthe tester does spark ara Oonds it automatically turns off The Quick Pye may G svor voltage less than 5 kV Use the K Mode to Si Meas Ny Mode S Te r N iy place Ta s receiver tip over the secondary ignition wire Or Poyorrosst button when the headlight begins to flash During tiak e the red and green LEDs stay lit while the tester measures the pe voltage for approximately 10 to 15 seconds When th tester finishes a measurement it will do all of the following The tester emits a beeping sound The headlight flashes 3 times The corresponding polarity LED lights LCD displays the current reading for 15 seconds After completing this sequence the tester returns to the Quick Test Mode You can also return to the Quick Test Mode by pressing the power toggle button while the kV is displayed Note It is normal for the LCD to flash random segments while the peak kV is measured Interpreting the Results 1 Compare voltages for all cylinde2. Warranty Subject to the conditions that follow and are noted below this product is warranted to be free from defects in material and workmanship under proper use and in accordance with the manufacturer s written recommendation and specifications for a period designated below on all products This product carries a limited lifetime warranty The manufacturer s obligation under this warranty is limited to unaltered products returned to the manufacturer by the initial end user of the new products Therefore this warranty does not cover any products resold by the end user to third parties nor any reconditioned products sold as such by the manufacturer The sole remedy for any such defect shall be the repair or replacement of the product at the sole discretion of the manufacturer This warranty does not cover expendable parts such as batteries nor does it cover shipping or handling In addition manufacturer is not liable for any loss or damage to product during shipping In the event it is determined that the product has been tampered with or altered in any way this warranty is void and all claims against the product will not be honored All warranty claims must be submitted as outlined by the manuf and shall be processed in accordance fi that proof of purchase must be es either warranty card from the seller or purchase receipt and thal manufacturer will make every attempt to r within one busing day fro ip th
3. e the red LED headlamp flashes when a spark is detected If the polarity is negative the green LED lights and if positive the red LED lights In the Measurement Mode the probe measures and displays the peak spark voltage for approximately 15 seconds Assembling the Tester 1 Attach the extension probe onto the tester Red LED Headlamp Signal receiver tip 2 Press fit the probe tip onto the extension probe ension Probe Red amp 7 e green LEDs Using the Tef B 1 Turn nAg on by fi No en n th Signal is alway receiver tip uick Ch pres the power plug wire fured toggle button g To indicate the tester is on the headlamp along with the red and green LEDs flash alternately and the tester emits a beeping sound for a short period 2 With the engine running firmly place the signal receiver tip over the spark plug wire see figure 2 For the best test results do the following Make sure all other secondary ignition wires and any metal objects are at least 1 inch from the receiver tip If adjacent wires metal are too close during testing the probe may provide inconsistent results Do not touch the receiver tip or the extension probe while testing Doing so will cause inaccurate readings On DIS vehicles the wasted spark may cause a doubling of the spark detection To avoid this and only detect the true spark slightly move the probe tip away from the ignition cable
4. e produc eceipt of th returned product repaid In additio aintegence proced s outlined duct manuals follo rranty toe e Sh t not be us dbi e witl s as specifie e uct w ils outside e wafranty the a rer resegyes the r to make such ent and returning the product e notifi a itten notification will be neces to irhe product at a cost which t cWrer deems as reasonable fen be shipped back to the or as the manufacturer deems customer appropriate This is the only authorized manufacturer s warranty and is in lieu of all other expressed or implied warranties or representations including but not limited to any implied warranties of merchantability or fitness or any other obligations on the part of the manufacturer In no vent will the manufacturer be liable for business interruptions loss of profit personal injury costs of delays or any special indirect incidental or consequential damages costs or losses 19120 845 Rev B 2004 Hickok Inc All rights reserved WAEKON a division of Hickok The kV Arc Quick Probe is a battery operated hand held tester designed to easily and quickly check the presence of a spark in the vehicle s cylinders determine the polarity and measure the peak voltage as the spark plug is firing on Distributor and Distributorless Ignition Systems The tester works by receiving a signal transmitted from the spark plug s wire In the Quick Check Mod
5. rs Make sure to measure at the same location on each wire On DIS vehicles the positive firing voltage is typically 3 5 kV less than the negative reading 2 Voltages above 20 kV indicate a non firing plug May cause the tester to reset or change modes Turning the Tester Off KY gt The tester automatically turns off after approximately 30 S conds of Gy Before shutting off all LEDs flash and the oN beeping ra short period Replacing the Batteries Replace the batteries when the poli 5 or the LC ents become dim The kV Arc Quick Probe usgit It cro yen batteries 1 Remove the two sc the handl 2 Carefully sepagate the dle and ve the old batteries 3 Place th A inth ositive side facing up 4 epe reason A S S R nt Pa l n order ur Customer Care department at 2 5080 or vi ur website at www quick n ezparts com scripti Part Number CR20 s 2 T2000 9P2 73 Adapter extension probe 16970 195 Signal Receiver Tip 16970 196 TOLI FREE trcusurpor 8007342 5080
Download Pdf Manuals
Related Search