Home
HDX HDXBR50 Use and Care Manual
Contents
1. 12 Cold weather operation 12 Recommended Hookup 13 Troubleshooting 14 2 Safety Information WARNING To avoid serious personal injury do not attempt to use this product until you read the manual thoroughly and understand it completely Save this manual and review frequently for continuing safe operation and instructing others who may use this tool PERSONAL SAFETY WARNING Instructions pertaining to a risk of fire electric shock or injury to persons WARNING When using tools basic precautions should always be followed including the followings WARNING This product or its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling SYMBOLS Read operator s manual To reduce the risk of injury gt user must read and understand operator s manual before using this product using this tool Failure to do so may result in O Risk to hearing Always wear ear protection when ji hearing loss Eye protection Always wear safety goggles safety cs glasses with side shields or a full face shield when operating this product Risk of serious personal injury Never place hands Fed or any other body parts in the fastener di
2. 25 C mo ajustar escape 25 C mo cargar los sujetadores 25 Operac on Continuaci n 26 C mo descargar los sujetadores 26 C mo retiarar sujetadores atascados 26 Operac on Continuaci n 27 C mo configurar la presi n de aire 27 C mo activar la herramienta 27 Elemento de contacto de trabajo WCE 27 Mantenimiento 28 Funci n antipolvo 28 Lubricaci n 28 Preguntas problemas 0 piezas faltantes Limpieza 28 Antes de regresar a la tienda llama al Servicio al Cliente de HDX Operaci n en climas fr oS 28 de lunes a viernes entre 8 a m y 6 p m Corek n recomendada eena eneee 29 hora del Eete de EE UU gt Soluci n de problemas 30 1 800 514 6729 HOMEDEPOT COM GRACIAS POR TU COMPRA S Apreciamos la confianza que has depositado en HDX al comprar de este clavadora de neum tico 17Sp HOM EDEPOT COM Nos esforzamos para continuamente crear productos
3. Problems Possible cause s Corrective action Air leaking at trigger O rings in trigger valve housing are Replace O rings TM valve area damaged Air leaking between O Loose screws in housing O Tighten screws q housing and nose O Damaged O rings O Replace O rings O Damaged to bumper O Replace bumper Air leaking between O Loose screws O Tighten screws housing and cap 0 Damaged gasket o Replace gasket Tool skips driving O Worn bumper O Replace bumper fastener O Dirt in nose piece O Clean drive channel O Dirt or damage prevent fasteners O Clean magazine or pusher from moving freely in magazine O Damaged pusher spring O Replace spring O Inadequate air flow to tool O Check fitting hose or compressor O Worn O ring on piston or lack O Replace and lubricate O rings of lubrication 0 Damaged O ring on trigger valve O Replace O rings O Air leaks O Tighten screws and fittings O Cap seal leaking O Replace gasket Tool runs slow or has O Tool not lubricated sufficiently D Lubricate nailer loss of power O Broken spring in cylinder cap D Replace spring O Exhaust port in cap is blocked O Replace damaged internal parts Question Problems missing parts Before returning to the store Fasteners are O Guide on driver is worn O Replace guide call HDX Customer Service jammed in tool O Fasteners are not correct size O Use only recommended fasteners 8 a m 6
4. 5 Tool Use and Care Continued 5 Tool S IVICE 2 2 nnn neem nnn n mene nnn n nn 5 All SUIT Oro 5 Operation 77 2mm 5 Safety Information Continued 6 Air Supply and Connections 6 Loading Tool 6 Warranty 2 22 22 22 7 Unpacking 7 SPeCificatiONn 2 2 nn 8 F Gatureg s 25 0n naan noi 8 Operation gt 9 Adjusting the Exhaust 9 Loading Fasteners 9 Operation Continued 10 Unloading Fasteners 10 Clearing aMS 4 10 Setting the Air Pressure 10 Operation Continued 11 Firing the Tool 11 Work Contact Element WCE 11 Maintenance 12 Anti dust Cap 12 Lubrication 12 Cleaning
5. PRECAUCI N Verifique el funcionamiento del mecanismo de disparo del elemento de contacto de trabajo antes de cada uso El WCE debe desplazarse libremente sin obstruirse a lo largo de toda la longitud de desplazamiento El resorte del WCE I debe regresar este ltimo a su posici n completamente extendida despu s de ser presionado No utilice la herramienta si el mecanismo de disparo del WCE no funciona adecuadamente ya que podr an ocurrir lesiones personales Resorte del WCE I HOM EDEPOT COM Para obtener asistencia por favor llama al 1 888 514 6729 Mantenimiento ADVERTENCIA Antes de inspeccionar dar mantenimiento y limpiar O Desconecta la herramienta de la fuente de aire O Vac a el cargador por completo FUNCI N ANTIPOLVO Todas las herramientas vienen con un tap n antipolvo en el conector de aire verificalo si lo tienes despu s de desempacar la herramienta Mant n el tap n antipolvo para cubrir el conector de aire LUBRICACI N La herramienta est dise ada exclusivamente para no necesitar lubricaci n diaria Pero la lubricaci n es necesaria para un mejor rendimiento luego de periodos de uso prolongados Si se agrega aceite a la herramienta a trav s de la conexi n de la l nea de aire se lubricar n las piezas internas No utilices aceite detergente ni aditivos puesto que estos lubricantes causar n el desgaste acelerado de los sellos y amortiguadores de la herramient
6. 4 Usa siempre protecci n auditiva cuando utilices la herramienta La exposici n prolongada a ruidos de alta intensidad puede causar la p rdida de la audici n 5 Usa un equipo de seguridad Se deben usar una m scara antipolvo calzado de seguridad antideslizante y un casco r gido en condiciones donde sean necesarios Usa una m scara protectora completa si est s trabajando con virutas de madera o limaduras de metales 6 Usa la vestimenta adecuada No utilices ropa o joyas sueltas Recoge el cabello largo Mant n el cabello la ropa y los guantes alejados de las partes m viles La ropa y las joyas sueltas o el cabello largo pueden quedar atrapados en las partes m viles 7 Cuando utilices una herramienta de motor mantente alerta observa lo que est s haciendo y utiliza el sentido com n No utilices la herramienta si est s cansado o bajo el efecto de drogas alcohol o medicamentos Un momento de distracci n durante la operaci n de la herramienta puede causar lesiones graves 8 Para evitar disparos accidentales mantenga los dedos alejados del gatillo cuando no accione los sujetadores especialmente cuando conecte la herramienta al suministro de aire ADVERTENCIA Instrucciones en referencia al peligro de incendios choque electrico o lesiones personales ADVERTENCIA Este producto a su cord n el ctrico puede contener productos quimicos conocidos por el estado de California como causantes de c ncer y defectos
7. en uso Un suministro inadecuado de aire puede causar una p rdida de potencia y un clavado desigual 2 Se puede usar un lubricador para proporcionar circulaci n de aceite en toda la herramienta Se puede usar un filtro para retirar las impurezas l quidas y s lidas las que pueden oxidar piezas internas de la herramienta o hacer que stas se apelmacen 3 Siempre use mangueras de aire comprimido con una clasificaci n de presi n de trabajo igual o superior a la presi n de la fuente de alimentaci n en caso que el regulador falle o de 10 34 bar el que sea mayor Use mangueras de aire comprimido de 3 8 para distancias de hasta 15 24 m y use un acoplador de conexi n r pida de 3 8 en la manguera de aire comprimido 4 Use un regulador de presi n en el compresor con una presi n de trabajo de O a 8 62 bar Se necesita un regulador de presi n que controle la presi n de trabajo de la herramienta entre 4 13 bar y 6 89 bar PRECAUCI N El compresor de aire debe ser capaz de mantener un m nimo de 4 13 bar mientras la herramienta est en uso Un suministro inadecuado de aire puede causar una p rdida de potencia y un clavado desigual A ADVERTENCIA No conectes la herramienta a un compresor de aire que pueda exceder las 13 79 bar La herramienta podr a explotar y posiblemente provocar lesiones Acople M r pido anguera Conector j j P deare Lubricador Filtro a a TTA TT z C
8. mencionadas anteriormente no abarcan todas las condiciones y situaciones posibles Es perfectamente comprensible que no podemos fabricar el sentido com n y la precauci n como partes de ning n producto el usuario es el responsable de obrar en consecuencia en el rea de descarga de los fijadores 3 Nunca apuntes la herramienta hacia las personas 4 No jale el gatillo ni presione la pieza de trabajo en contacto ya que se podr a accionar accidentalmente y posiblemente causar lesiones Garant a GARANT A LIMITADA DE UNO A O DE CLAVADORA DE NEUM TICO DE HDX Esta garant a cubre defectos de fabricaci n o materiales de este clavadora de neum tico HDX por un periodo de uno a o desde la fecha de compra Esta garant a es espec fica a este clavadora de neum tico Las garant as de otros productos HDX pueden variar Esta garant a se aplica s lo al comprador original y no puede transferirse Esta garant a no cubre el desgaste normal por uso o mal funcionamiento fallas o defectos que resulten del uso incorrecto abuso negligencia alteraci n modificaci n o reparaci n de un centro de servicio distinto al autorizado para reparar los clavadora de neum tico de marca HDX Los materiales expansibles como juntas t ricas parachoques acconadora sellos etc no est n cubiertos por esta grant a Esta garant a no se aplica si este clavadora de neum tico es usado para aplicaciones industriales o de alquiler HDX no garant
9. n 4 13 6 89 bar O Rango de tama o del pasador 10mm 3 8 a 50mm 2 oe 10mm 3 8 16mm 5 8 20mm 3 4 25mm 1 30mm 1 3 16 32mm 1 1 4 38mm 1 1 2 40mm 1 5 8 50mm 2 wugo 1 OO Compatible con todas las marcas gen ricas de pistolas para clavos calibre 18 Operaci n 1 C mo ajustar el escape El escape ajustable en la cubierta de la herramienta permite a los usuarios controlar los escapes de acuerdo a las preferencias del operador Para ajustar la direcci n gire la cubierta del tubo de escape a la direcci n deseada 2 C mo cargar los sujetadores O Conecte la herramienta a la fuente de aire O Presione el bot n del pestillo A hacia abajo J ale hacia atr s la cubierta del cargador B O Inserte los sujetadores en el riel del cargador C Aseg rese de que los sujetadores permanezcan en el reborde posterior del cargador cuando realice la carga Aseg rese de que los sujetadores no est n sucios ni da ados O Presione la cubierta del cargador B hacia adelante hasta que el bot n del pestillo emerja Bot n del pestillo A 25Sp La cubierta del cargador B Riel del carga
10. personales graves o la muerte 3 Use nicamente una fuente de aire comprimido de presi n regulada para limitar la presi n de aire suministrada a la herramienta La presi n regulada no debe superar los 6 89bar Si el regulador falla la presi n enviada a la herramienta no debe superar los 13 79bar El exceso de presi n de la herramienta es capaz de ocasionar una explosi n funcionamiento anormal rotura de la herramienta o lesiones graves a personas Utilice s lo aire limpio y seco y regulado a la presi n nominal o dentro del rango de presi n indicado en la herramienta Verifique siempre antes de utilizar la herramienta que la fuente de aire se ha ajustado a la presi n de aire especificada o dentro del rango nominal de presi n de aire 4 Desconecta siempre la fuente de aire O Antes de descargar o realizar ajustes O Al realizar el mantenimiento de la herramienta O Al desatascarla O Al tocar la horquilla de seguridad O Cuando la herramienta no est en uso O Al desplazarse a otra rea de trabajo Dichas medidas de precaucion reduciran el riesgo de lesiones a personas HOM EDEPOT COM Para obtener asistencia por favor llama al 1 888 514 6729 Informac n de Seguridad Continuaci n CARGAR LA HERRAMIENTA 1 No cargues la herramienta con fijadores si alguno de los controles operativos est activado 2 Nunca coloques la mano ni ninguna otra parte del cuerpo ADVERTENCIA Las advertencias y precauciones
11. aire siempre dispare la herramienta varias veces sobre un trozo de madera que no utilice para asegurarse de que se expenda todo el aire comprimido A Operaci n Continuaci n 5 C mo configurar la presi n de aire OLa cantidad de presi n de aire requerida depende del tama o de los fijadores y del material de la pieza de trabajo a Comienza por comprobar la profundidad de clavado disparando un clavo de prueba hacia una pieza de trabajo del mismo material utilizado para el trabajo real ODispara un fijador de prueba con la presi n de aire configurada a 6 2 6 6 bar Aumenta o reduce la presi n de aire para hallar la configuraci n m s baja posible para realizar el trabajo con resultados uniformes O Es posible que se pueda lograr la profundidad deseada ajustando nicamente la presi n de aire 6 Como activar la herramienta oLa herramienta est dise ada especialmente para el modo secuencial simple Este modo requiere que se jale el gatillo cada vez que se dispara un sujetador Se puede accionar la herramienta presionando el elemento de contacto de trabajo G contra la superficie de trabajo seguido de la presi n del gatillo H OSe debe liberar el gatillo para reiniciar la herramienta antes de que se dispare otro sujetador Elemento de contacto de trabajo G Gatillo H ADVERTENCIA Siempre conozca el modo de funcionamiento de la herramienta antes de usarla de lo contrario podr a ocasi
12. are factors which cannot be built into this product but must be supplied by the user Warranty HDX PNEUMATIC NAILER LIMITED ONE YEAR WARRANTY This warranty covers defects in workmanship or materials in this HDX pneumatic nailer for the one year period from the date of purchase This warranty is specific to this pneumatic nailer Warranties for other HDX products may vary This warranty applies only to the original retail purchaser and may not be transferred This warranty does not cover normal wear and tear or any malfunction failure or defect resulting from misuse abuse neglect alteration modification or repair by other than a service center authorized to repair HDX branded air nailer Expendable materials such as O rings bumpers driver blades seals etc are not covered by this warranty This warranty does not apply to pneumatic nailer used in industrial application or for rental purposes HDX makes no warranties representations or promises as to the quality or performance of its pneumatic nailer other than those specifically stated in this warranty ADDITIONAL LIMITATIONS To the extent permitted by applicable law all implied warranties including warranties of merchantability or fitness for a particular purpose are disclaimed Any implied warranties including warranties of merchantability or fitness for a particular purpose that can not be disclaimed under state law are limited to one year from the date of purchase HD
13. be directed toward anything other than the workpiece 15 Never use gasoline or other flammable liquids to clean the tool Never use the tool in the presence of flammable liquids or gases Vapors could ignite by a spark and cause an explosion which will result in death or serious personal injury 16 Do not remove tamper with or otherwise cause the trigger lock or trigger to become inoperable Do not operate any tool which has been modified in a like fashion Death or serious personal injury could result 17 Do not touch the trigger unless driving fasteners Never attach air line to tool or carry tool while touching the trigger The tool could eject a fastener which will result in death or serious personal injury Also actuate the trigger lock to the safe position when not in use 18 Always fit tool with a fitting or hose coupling on or near the tool in such a manner that all compressed air in the tool is discharged at the time the fitting or hose coupling is disconnected Do not use a check valve or any other fitting which allows air to remain in the tool Death or serious personal injury could occur 19 Never place hands or any other body parts in the fastener discharge area of the tool The tool might eject a fastener and could result in death or serious personal injury 20 Never carry the tool by the air hose or pull the hose to move the tool or a compressor Keep hoses away from heat oil and sharp edges Replace any hose that is damage
14. conecte a una fuente de aire que pueda superar los 13 79 bar El exceso de presi n de la herramienta es capaz de ocasionar una explosi n funcionamiento anormal rotura de la herramienta o lesiones graves a personas Utilice s lo aire limpio y seco y regulado a la presi n nominal o dentro del rango de presi n indicado en la herramienta Verifique siempre antes de utilizar la herramienta que la fuente de aire se ha ajustado a la presi n de aire especificada o dentro del rango nominal de presi n de aire 2 Nunca utilice ox geno di xido de carbono gases combustibles u otros gases embotellados como fuente de aire para la herramienta Dichos gases pueden explotar y causar lesiones graves a las personas FUNCIONAMIENTO 1 No coloques fijadores cerca del borde del material La pieza de trabajo puede partirse y hacer que el fijador rebote y te da e ati o a las personas alrededor 2 No traslade la herramienta de un lugar a otro presionando el gatillo Esto podr a provocar una descarga accidental La opci n del m todo de disparos es importante Verifique el manual para las opciones de disparo 3 Durante el uso normal la herramienta se rebobinar de inmediato luego de accionar un sujetador Esta es una funci n normal de la herramienta No intente evitar la rebobinaci n sosteniendo la herramienta en contra del funcionamiento La restricci n para rebobinar puede provocar que se accione un segundo sujetador desde la herramienta S
15. de calidad dise ados para tu hogar Visitanos por Internet para ver nuestra Para obtener asistencia por favor llama al 1 888 514 6729 lea completa de propductos disponibles para tus necesidades de mejoras en el hogar Gracias por elegir HDX Informac n de Seguridad ADVERTENCIA Para evitar lesiones personales graves no intentes usar este producto hasta haber le do y comprendido el manual por completo Guarda este manual y cons ltalo con frecuencia para un funcionamiento seguro y para instruir a otros usuarios de esta herramienta A ADVERTENCIA Cuando se usen herramientas siempre se deber n seguir precauciones b sicas incluyendo las siguientes A S MBOLOS Lea el manual del operador de Para reducir el riesgo de lesiones el usuario debe leer y entender el manual del operador antes de usar este producto El riesgo a la audici n Siempre use protecci n para los o dos cuando se utiliza este tool Failure lo contrario podr a resultar en la p rdida de audici n Protecci n de los ojos Use siempre gafas de seguridad gafas de seguridad con protecci n lateral o una careta completa cuando utilice esta producto Riesgo de lesiones personales graves Nunca coloque las manos o cualquier otra parte del cuerpo en la zona de descarga del sujetador de la clavadora La herramienta puede expulsar un sujetador y puede causar la muerte o lesiones graves AREA DE TRABA O 1 Manteng
16. inconsistent driving 2 An oiler can be used to provide oil circulation through the tool A filter can be used to remove liquid and solid impurities which can rust or gum up internal parts of the tool 3 Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails or 150 psi whichever is greater Use 3 8 air hose for runs up to 50 and use a 3 8 quick coupler on the air hose 4 Use a pressure regulator on the compressor with an operating pressure of 0 125 psi A pressure regulator is required to control the operating pressure of the tool between 60 psi and 100 psi Quick coupler Quick connector CAUTION The air compressor must be able to maintain a minimum of 60 psi when the tool is being used An inadequate air supply can cause a loss of power and inconsistent driving A WARNING Do not connect with air compressor which can potentially exceed 200 psi As tool may burst possibly causing injury Quick Air hose connector Quick coupler r Oiler Filter 4 Compressor HOM EDEP OT COM Please contact 1 800 514 6729 for further assistance Troubleshooting WARNING Stop using tool immediately if any of the following problems occur Serious personal injury could result Any repairs or replacements must be done by a qualified service person or an Authorized service center
17. job O Drive a test fastener with the air pressure set at 90 95psi Raise or lower the air pressure to find the lowest setting that will perform the job with consistent O results It may be possible to achieve the desired depth with air pressure adjustments alone Operation Continued 6 Firing the tool O The tool is specially designed for single sequential mode This mode requires the trigger to be pulled each time a fastener is driven The tool can be actuated by depressing the Work Contact Element WCE G against the work surface followed pulling the trigger H The trigger must be released to reset the tool before another fastener can be driven O Work contact element G Trigger H WARNING Always know the operational mode of the tool before using Failure to know the operational mode could result in death or serious personal injury used Do not actuate the tool unless the tool is placed A WARNING An improperly functioning tool must not be firmly against the work place 11 J Work contact element WCE O Disconnect the air supply from the tool O Remove all fasteners from the magazine O Make sure the trigger and work contact element move freely up and down without sticking or binding O Reconnect air supply to the tool O Depress the work contact element against the work surface without pulling the trigger the tool must not operate Do not use the tool if
18. o el acoplador de la manguera est n desconectados No utilice una v lvula de control ni ning n otro conector que permita que el aire permanezca en la herramienta en caso contrario podr an ocurrir lesiones personales graves o la muerte 20Sp 19 Nunca coloque las manos ni otra parte del cuerpo en el area de descarga de sujetadores de la herramienta La herramienta podria lanzar un sujetador y provocar lesiones personales graves o la muerte 20 Nunca transporte la herramienta de la manguera de aire comprimido ni jale la manguera para mover la herramienta o un compresor Mantenga las mangueras alejadas del calor el aceite y los bordes filosos Reemplace las mangueras da adas o desgastadas en caso contrario podr an ocurrir lesiones personales o da os en la herramienta 21 Siempre d por sentado que la herramienta contiene sujetadores Considere la herramienta como un implemento de trabajo y no juegue con ella 22 Siempre mantenga a las dem s personas a una distancia segura del lugar de trabajo en caso se produzcan descargas accidentales de sujetadores No apunte la herramienta hacia usted u otra persona aun cuando no contenga sujetadores La activaci n accidental de la herramienta podr a provocar lesiones personales graves ola muerte 23 No deje caer ni lance la herramienta Ya que esto podr a ocasionar da os en la herramienta y causar que la misma ya no sea utilizable o segura Si la herramienta ha sufrido ca das o ha
19. p m EST Monday Friday O Fasteners are bent O Replace with undamaged fasteners O Magazine or nose screws are O Tighten screws loose 1 800 514 6729 O Driver is damaged O Replace driver HOMEDEPOT COM Retain this manual for future use 14 Tabla de Contenido Articulo 1000 054 026 E a WNNS Pe Modelo HDXBR50 Tabla de o eno 17 Informac n de seguridad 18 FT LJA S mboloS 18 rea De Trabajo 18 Seguridad personal 18 z Informac n de seguridad Continuaci6n 19 GU IA D E U SO Y M ANTE N M E NTO Seguridad personal Continuaci n 19 Uso y cuidado de la herramienta 19 CLAVADORA DE PUNTILLA atea oo CALIBRE 18 DE 50MM 2 gs ie aA Fuente del aire 21 00001 FUNE oeie aa 21 l Entrada de aire y conexiones 21 Informac n de seguridad Continuaci6n 22 Cargar la herramienta 22 N 22 Desempacar 23 EspecificacioneS 24 Caracter sticaS 24 Operac on
20. shoes and a hard hat must be used for the applicable conditions Wear a full face shield if you are producing metal filings or wood chips 6 Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts 7 Stay alert watch what you are doing and use common sense when operating a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating the tool may cause serious injury 8 Avoid unintentional firing Keep fingers away from trigger when not driving fasteners especially when connecting the tool to the air supply 9 Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations 10 Do not use on a ladder or unstable supports Stable footing on a solid surface enables better control of the tool in unexpected situations 11 Make sure the hose is free of obstructions or snags Entangled or snarled hoses can cause loss of balance or footing and may become damaged resulting in possible injury HOM EDEP OT COM Please contact 1 800 514 6729 for further assistance Safety Information Continued PERSONAL SAFETY CONTINUED 12 Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool
21. LIFNY LAS Preguntas problemas o piezas faltantes Antes de regresar a la tienda llama al Servicio al Cliente de HDX de lunes a viernes entre 8 a m y 6 p m hora del Eete de EE UU 1 800 514 6729 HOM EDEPOT COM Guarde este manual para futuras consultas REF IMX100102AV E S 05 14 Item 1000 054 026 E EPEN Model HDXBR50 IEA USE AND CARE GUIDE 18 GA 2 BRAD NAILER Question Problems missing parts Before returning to the store call HDX Customer Service 8 a m 6 p m EST Monday Friday 1 800 514 6729 HOMEDEP 0T COM THANK YOU We appreciate the trust and confidence you have placed in HDX through the purchase of this pneumatic nailer We strive to continually create quality products designated to enhance your home Visit us online to see our full line of products available for your home improvement needs Thanks you for choosing HDX Table of Contents Table of Contents 2 Safety Information 3 SYMONS 222 2 nen n 3 Work Area 3 Personal Safety 3 Safety Information Continued 4 Personal Safety Continued 4 Tool Use and Care 4 Safety Information Continued
22. X is not responsible for direct indirect incidental special or consequential damages If this pneumatic nailer is used for commercial purposes the warranty will apply for ninety 90 days from the date of purchase Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Unpacking 1 This tool has been shipped completely assembled 2 Carefully remove the tool and any accessories from the box 3 Inspect the tool carefully to make sure no breakage or damage occurred during shipping 4 Do not discard the packing material until you have WARNING Do not attempt to modify the tool or carefully inspected and satisfactorily operated the tool A create accessories not recommended for use with 5 If any parts are damaged or missing please call the tool Any such alteration or modification is io A oe misuse and could result in hazardous condition leading to possible serious personal injury tool until the missing parts are replaced Failure to do WARNING If any parts are missing do not operate the so could result in possible serious personal injury 7 HOM EDEP OT COM Please contact 1 800 514 6729 for further assistance Specifications O Air consumpt
23. a lo que resultar en el mal funcionamiento de la misma y elevar la frecuencia del mantenimiento PRECAUCI N Lubrica la herramienta nicamente con los lubricantes especificados LIMPIEZA Evita el uso de solventes para limpiar las piezas pl sticas La mayor a de los pl sticos pueden da arse con facilidad al usar varios tipos de solventes comerciales Usa pa os limpios para limpiar la suciedad polvo grasa etc ADVERTENCIA En ning n momento dejes que l quidos para freno gasolina productos a base de petr leo aceites penetrantes etc entren en contacto con las piezas pl sticas Estos qu micos pueden da ar debilitar o destruir el pl stico lo que puede provocar lesiones graves OPERACI N EN CLIMAS FR OS En caso de operaci n en climas fr os cerca o debajo del punto de congelamiento la humedad en la l nea de aire puede congelarse evitando el funcionamiento de la herramienta Recomendamos usar lubricantes para herramientas neum ticas o un anticongelante permanente glicol de etileno como lubricante para climas fr os PRECAUCI N No almacenes la herramienta en un ambiente de clima fr o para evitar la formaci n de A escarcha o hielo sobre las valvulas y mecanismos operativos de la herramienta pues la misma podr a dejar de funcionar Conexi n recomendada 1 El compresor de aire debe ser capaz de mantener un m nimo de 4 13 bar mientras la herramienta est
24. a el area de trabajo limpia y bien iluminada Los bancos de trabajo desordenados y las reas oscuras aumentan el riesgo de accidentes 2 No utilice la herramienta en atm sferas en las que exista riesgo de explosi n como por ejemplo en presencia de l quidos inflamables gases o polvo La herramienta produce una chispa que podr a encender l quidos inflamables gases o polvo 3 Mantenga a los transe ntes ni os y a otras personas alejadas cuando est utilizando la herramienta Las distracciones podr an resultar en el uso inapropiado y causar lesiones 4 Evite los disparos accidentales Siempre tenga precauci n para evitar disparos accidentales No apunte la herramienta hacia usted u otra persona aun cuando no contenga sujetadores 18Sp SEGURIDAD PERSONAL A A 1 No clave sobre otro clavo Esto puede causar que el clavo se desv e y alcance a alguien o que la herramienta reaccione de alguna manera y lesione a alguien 2 Retire el dedo del gatillo cuando no coloca sujetadores Nunca transporte la herramienta con el dedo en el gatillo ya que la herramienta puede disparar un sujetador 3 Usa siempre protecci n para los ojos El operador y las otras personas en el rea de trabajo deben usar siempre gafas de seguridad con protectores laterales aprobadas por ANSI La protecci n de los ojos se utiliza para resguardarlos de los fijadores y residuos que puedan saltar los cuales pueden causar lesiones graves en los ojos
25. a pressure regulated compressed air source to limit the air pressure supplied to the tool The regulated pressure must not exceed 100psi If the regulator fails the pressure delivered to the tool must not exceed 200psi Over pressurizing the tool is able to result in bursting abnormal operation breakage of the tool or serious injury to persons Use only clean dry regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air pressure range 4 Always disconnect air source O Before unloading or making adjustments O When maintaining the tool O When clearing a jam oO When touching the safety yoke O When tool is not in use O When moving to a different work area Such precautionary measures reduce the risk of injury to persons N w LOADING TOOL 1 Do not load the tool with fasteners when any one of the operating controls is activated 2 Never place a hand or any part of body in fastener discharge area of tool 3 Never point tool at anyone 4 Do not pull the trigger or depress the workpiece contact as accidental actuation may occur possibly causing injury WARNING The warnings and precautions discussed above cannot cover all possible conditions and situations that may occur It must be understood by the user that common sense and caution
26. aci n O Las juntas t ricas en la v lvula del gatillo est n da adas O Hay fuga de aire O Hay fuga en el sello de la cubierta Cambie el protector Limpie la canaleta de disparo Limpie el cargador Cambie el resorte Revise los conectores la manguera o el compresor O Cambie y lubrique las juntas t ricas OOOOdO Cambie las juntas t ricas Apriete los tornillos y los conectores OO O Reemplace la empaquetadura La herramienta pierde velocidad o potencia La herramienta no cuenta con suficiente lubricaci n Hay un resorte roto en la cubierta del cilindro O EL puerto de descarga en la cubierta est bloqueado Lubrique la clavadora Cambie el resorte Cambie las piezas internas da adas OOO Los sujetadores se atascan en la herramienta La gu a de disparo est desgastada O Los sujetadores no son del tama o apropiado O Los sujetadores est n torcidos El cargador o los tornillos del borde est n flojos El mecanismo de disparo est da ado O Cambie la gu a O Use nicamente los sujetadores recomendados O Cambie por sujetadores en buena condici n O Apriete los tornillos O Cambie el mecanismo de disparo 30Sp
27. ad all fasteners before removing tool from service WARNING Always disconnect the air source before unloading WARNING Disconnect the tool from the air source whenever clearing a jam After disconnecting the tool from the air compressor there should still be A enough air pressure to fire the tool After the air hose is disconnected always fire the tool into scrap wood repeatedly to make sure all of the compressed air is expended 4 Clearing jams Occasionally a fastener may become jammed in the firing mechanism of the tool making the tool inoperable To remove a jammed fastener follow the steps below O Disconnect the tool from air source Remove fasteners from the tool Failure to do so will cause the fasteners to eject from the front of the tool O Completely remove the small nose screws D and the top nose plate E to reveal the jammed fastener O Using caution not to bend or damage the driver blade using pliers or a screwdriver if required to clear the jammed fastener O Put the nose plate E back on the nose F fastening it with the screws D O Reconnect the tool to the air source O Reload the tool with fasteners 5 Setting the air pressure O The amount of air pressure required depends on the size of the fasteners and the workpiece material O Begin testing the depth of drive by driving a test nail into the same type of workpiece material used for the actual
28. advertencia pueden producirse lesiones graves ja 3 Inspecciona la herramienta cuidadosamente para asegurarte de que no haya ocurrido ninguna rotura ni da o durante el env o ADVERTENCIA No intentes modificar esta 4 No deseches el material de empaque hasta que hayas herramienta o construir accesorios no inspeccionado cuidadosamente y utilizado recomendados para la misma Tales modificaciones o satisfactoriamente la herramienta cambios son considerados un mal uso y pueden 5 Si alguna pieza esta da ada o falta llama al resultar en condiciones peligrosas que a su vez 1 800 514 6729 pueden posiblemente causar lesiones 23Sp HOM EDEP OT COM Para obtener asistencia por favor llama al 1 888 514 6729 Especificaciones O Necesita 5 87 SCFM con 100 sujetadores por minuto a 6 2 bar O Entrada de aire NPT de 1 4 O Capacidad del cargador 100 sujetadores de calibre 18 O Peso de la herramienta 1 25 kg Caracter sticas O Escape ajustable en 360 grados Permite al usuario controlar el aire lejos de los cara O C moda manija de agarre Para mayor comodidad y control O Estructura de dise o ergon mico Resistente y c moda que resulta en una herramienta liviana ideal para un uso prolongado O Indicador de recarga Que permite un reemplazo r pido de la rec mara O Empujador de resorte doble Para una alimentaci n constante 24Sp Presi n m xima 6 89 bar Rango de presi
29. best performance Oil for the tool is added through the air line connection and will lubricate the internal parts Do not use detergent oil or additives as these lubricants will cause accelerated wear to the seals and bumpers in the tool resulting in poor tool performance and frequent tool maintenance CAUTION Lubricate tool with specified lubricants CLEANING Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and maybe damaged by their use Use clean cloths to remove dirt dust oil grease etc WARNING Do not at any time let brake fluids gasoline petroleum based products penetration oils A ect come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious personal injury COLD WEATHER For cold weather operation near and below freezing the moisture in the air line may freeze and prevent tool operation We recommend the use of air tool lubricant or permanent antifreeze ethylene glycol as a cold weather lubricant CAUTION Do not store tools in a cold weather environment to prevent frost or ice formation on the tool s operating valves and mechanisms that could cause tool failure Recommended hookup 1 The air compressor must be able to maintain a minimum of 60 psi when the tool is being used An inadequate air supply can cause a loss of power and
30. ck for misalignment or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools 6 Maintain tools with care Keep tool clean A properly maintained tool reduces the risk of binding and is easier to control 7 Store tools out of the reach of children and other untrained people Tools are dangerous in the hands of untrained users 8 Check operation of the tool before use Do not use the tool if the workpiece contact mechanism is not working correctly as accidental driving of a fastener may occur 9 Do not use tool if trigger does not actuate properly Any tool that cannot be controlled with the trigger is dangerous and must be repaired 10 Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed 11 Use clamps or another practical way to secure and support the workpiece to a stable platform Holding a tool by hand or against the body is unstable and may lead to loss of control 12 Keep the tool and its handle dry clean and free from oil and grease Always use a clean cloth when cleaning Never use brake fluids gasoline petroleum based products or any strong solvents to clean your tool 13 Do not use the tool as a hammer 14 Never use this tool in a manner that could cause a fastener to
31. d weak or worn Personal injury or tool damage could occur Safety Information Continued TOOL USE AND CARE CONTINUED 21 Always assume the tool contains fasteners Respect the tool as a working implement no horseplay 22 Always keep others at a safe distance from the work area in case of accidental discharge of fasteners Do not point the tool toward yourself or anyone whether it contains fasteners or not Accidental triggering of the tool could result in death or serious personal injury 23 Do not drop or throw the tool Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe If the tool has been dropped or thrown examine the tool closely for bent cracked or broken parts and air leaks STOP and repair before using or serious injury could occur 24 Avoid using the tool when the magazine is empty Accelerated wear on the tool may occur 25 Clean and check all air supply hoses and fittings before connecting the tool to an air supply Replace any damaged or worn hoses or fittings Tool performance or durability may be reduced 26 Do not use the tool if it leaks air or does not function properly 27 Do not operate the tool if it does not contain a legible warning label 28 Always Carry the tool by the handle Never carry the tool by the air hose TOOL SERVICE 1 Use only accessories that are identified by the manufacturer for the specific tool model 2 When servicing a tool use of u
32. de nacimiento u otros da os reproductiveos Lave sus manos despu s de usar Informac n de Seguridad Continuaci n SEGURIDAD PERSONAL CONTINUACI N 9 Mant n siempre una posici n firme y el equilibrio adecuado Una posici n firme y el equilibrio adecuado permiten controlar mejor la herramienta en situaciones inesperadas 10 No la utilices sobre una escalera de tijera o soportes inestables Una posici n estable sobre una superficie s lida permite un mejor control de la herramienta en situaciones imprevistas 11 Aseg rate de que la manguera est libre de obstrucciones o trabas Las mangueras atascadas o enredadas pueden causar la p rdida del equilibrio o la estabilidad y pueden da arse y causar lesiones 12 No se extienda demasiado Mantenga un apoyo de pies y un equilibrio adecuados en todo momento Un apoyo de pies y equilibrio adecuados permiten un mejor control de la herramienta en situaciones inesperadas 13 No fije la manguera o herramienta a su cuerpo Fije la manguera a la estructura para reducir el riesgo de p rdida de equilibrio en caso que la manguera se mueva 14 Siempre d por sentado que la herramienta contiene sujetadores No apunte la herramienta hacia usted u otra persona aun cuando no contenga sujetadores 15 L vese las manos despu s de manipularlo Este producto o su cable el ctrico pueden contener sustancias qu micas reconocidas por el estado de California como causantes de c ncer de
33. dor C A ADVERTENCIA La herramienta puede dispararse al ser conectada por primera vez a la fuente de aire Conecta siempre la herramienta a la fuente de aire antes de cargar los fijadores para evitar lesiones causadas por ciclos accidentales Aseg rate siempre de que el cargador de la herramienta est vac o al comienzo de cada sesi n de trabajo antes de conectarla a una fuente de aire ADVERTENCIA Mantenga la herramienta en direcci n opuesta a usted y otras personas al cargar los sujetadores No hacerlo podr a provocar lesiones personales graves ADVERTENCIA Use solamente los sujetadores recomendados para esta herramienta Los sujetadores no identificados por el fabricante de la herramienta para usarse con la misma pueden causar lesiones a las personas o da os en la herramienta cuando se usan con ella A ADVERTENCIA Nunca cargue el sujetador con la pieza de trabajo en contacto o el gatillo activado Esto podr a provocar lesiones personales graves HOM EDEPOT COM Para obtener asistencia por favor llama al 1 888 514 6729 Operaci n Continuaci n 3 C mo descargar los sujetadores La descarga es lo opuesto a la carga Excepci n siempre desconecte la fuente de aire antes de realizar la descarga sujetadores antes de retirar la herramienta del A ADVERTENCIA Siempre descargue todos los servicio ADVERTENCIA Conecta siempre la herramienta a la f
34. e la herramienta 6 Cuida la herramienta para mantenerla en buenas condiciones Mant n limpia la herramienta Una herramienta con el mantenimiento adecuado corre menos riesgo de bloquearse y es m s f cil de controlar 7 Guarda las herramientas fuera del alcance de los ni os y otras personas que no sepan como utilizarlas Las herramientas son peligrosas en manos de usuarios que no saben como utilizarlas 8 Comprueba el funcionamiento de la herramienta antes de usarla No uses la herramienta si el mecanismo de contacto de la pieza de trabajo no funciona correctamente para evitar disparar los fijadores accidentalmente 9 No utilice la herramienta si el gatillo no se acciona correctamente Toda herramienta que no pueda controlarse con el gatillo es peligrosa y debe repararse HOM EDEPOT COM Para obtener asistencia por favor llama al 1 888 514 6729 Informac n de Seguridad Continuaci n USO Y CUIDADO DE LA HERRAMIENTA CONTINUAC N 10 No fuerces la herramienta Utiliza la herramienta correcta seg n la aplicaci n La herramienta correcta realizar el trabajo mejor y con m s seguridad a la velocidad para la cual est dise ada 11 Usa abrazaderas u otra forma pr ctica para asegurar y sujetar la pieza de trabajo a una plataforma estable Sostener la herramienta con la mano o apoyarla contra el cuerpo no ofrece la estabilidad adecuada y puede causar p rdida de control 12 Mant n la herramienta y el mango sec
35. fectos cong nitos y otros da os en el aparato reproductivo 19Sp USOY CUIDADO DE LA HERRAMIENTA ADVERTENCIA Disconecten la grapadora de el aire antes de ajustes mantenimiento tacto del yugo de A seguridad quitando grapas quebradas y terminado el proyecto Esto va ayudar para que nadien tenga un dano 1 Inf rmate sobre la herramienta Lee el manual con cuidado aprende sobre sus aplicaciones y limitaciones como tambi n sobre los riesgos espec ficos y potenciales relacionados con la herramienta 2 Utilice s lo los sujetadores recomendados para cada modelo No utilice sujetadores inadecuados ni cargue los sujetadores de forma incorrecta 3 Usa nicamente accesorios identificados por el fabricante para ese modelo espec fico de herramienta La utilizaci n de piezas no autorizadas o el incumplimiento de las instrucciones de mantenimiento pueden aumentar el riesgo de lesiones 4 Use solamente los sujetadores recomendados para esta herramienta Los sujetadores no identificados por el fabricante de la herramienta para usarse con la misma pueden causar lesiones a las personas o da os en la herramienta cuando se usanconella 5 Comprueba que las piezas m viles no est n desalineadas ni bloqueadas que no haya piezas da adas o cualquier otra condici n que pueda afectar el funcionamiento de la herramienta Si est da ada repara la herramienta antes de utilizarla Muchos accidentes se deben al mantenimiento incorrecto d
36. in a second fastener being driven from the tool Grip the handle firmly and let the tool do the work Failure to heed this warning can result in serious personal injury 4 Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury 5 Do not actuate the tool unless you intend to drive a fastener into the workpiece 6 Always handle the tool with care O Respect the tool as a working implement O Never engage in horseplay O Never pull the trigger unless nose is directed toward the work O Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur possibly causing injury HOM EDEP OT COM Please contact 1 800 514 6729 for further assistance Safety Information Continued AIR SUPPLY AND CONNECTIONS 1 The Connector on the tool must not hold pressure when air supply is disconnected If an incorrect fitting is used the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected possible causing injury Do not use any type of reactive gases including but not limited to oxygen and combustible gases as a power source Use filtered lubricated regulated compressed air only Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury Use only
37. in unexpected situations 13 Do not attach the hose or tool to your body Attach the hose to the structure to reduce the risk of loss of balance ifthe hose shifts 14 Always assume that the tool contains fasteners Do not point the tool toward yourself or anyone whether it contains fasteners or not 15 Wash hands after handling This product or its power cord may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm TOOL USE AND CARE WARNING Disconnect the tool from the air source before making adjustments doing tool maintenance AN clearing jams touching the safety yoke leaving work area or unloading the tool Such precautionary measures reduce the risk of injury to persons 1 Know this tool Read manual carefully learn its applications and limitations as well as the specific potential hazards related to this tool 2 Use only fasteners that are recommended for your models Do not use the wrong fasteners or load the fasteners incorrectly 3 Use only accessories that are identified by the manufacturer for the specific tool model Use of unauthorized parts or failure to follow maintenance instructions may create a risk of injury 4 Use only those fasteners recommended for use with this tool Fasteners not identified for use with this tool by the tool manufacturer are able to result in a risk of injury to persons or tool damage when used in this tool 5 Che
38. ion 5 87 SCFM with 100 fasteners per minute 90psi O Air inlet 1 4 inch NPT O Magazine capacity 100 fasteners 18 gauge O Weight 2 77 lbs Specifications U 360 Adjustable exhaust Allows userto direct air away fromface O Comfort grip handle For increased comfort and control O Ergonomically engineered body Rugged and comfortable resulting in a light weight tool great for extended use O Reload indicator Allows for quick magazine replacement O Dual spring pusher For consistent feed Maximum pressure 100 psi Pressure range 60 psi 100 psi Pin size range 3 8 inch to 2 inch 0 079 2mm lt gt E 10mm 3 8 N 16mm 5 8 S 20mm 3 4 3 25mm 1 30mm 13 16 2 32mm 1 1 4 gt lo 38mm 1 1 2 2 3 k 40mm 1 5 8 3 50mm 2 Compatible with All Generic 18 Gauge Brad Nails 0S0 0 Operation 1 Adjusting the exhaust The adjustable exhaust on the cap of the tool allows users to direct the exhaust according to operator preference To adjust the direction turn the exhaust cap in the desired direction 2 Loading Fasteners O Connect the tool to the air source O Push down on the latch button A Pull back on the magazine cover B O Insert a stick of fasteners into the magazine rail C Make sure the pointed ends of the fasteners are resti
39. it operates without pulling the trigger Personal injury may result Remove the tool from the work surface the work contact element WCE must return to its original down position the tool must not operate Do not use the tool if it operates while lifted from the work surface Personal injury may result O Pull the trigger and depress the work contact element WCE against the work surface The tool must not operate O Depress the work contact element WCE against the surface pull the trigger The tool must operate O CAUTION Check the operation of the work contact element trip mechanism before each use The WCE must move freely without binding through its entire travel distance The WCE spring I must return the WCE to its fully extended position after being depressed Do not operate the tool if the WCE trip mechanism is not operating properly Personal injury may occur WCE Spring I HOM EDEPOT COM Please contact 1 800 514 6729 for further assistance Maintenance WARNING Any time inspection maintenance and cleaning are done O Disconnect the tool from the air source O Empty the magazine completely ANTI DUST CAP Each tool is packed with an anti dust cap on the air connector check it after unpacking Keep the anti dust cap covering the air connector when the tool is not in use LUBRICATION Frequent but not excessive lubrication is required for
40. iza representa ni promete la calidad o rendimiento de estos clavadora de neum tico distintos a los especificados en esta garant a LIMITACIONES ADICIONALES En la medida en que la ley lo permita se excluyen todas las garant as impl citas incluyendo garant as de comercializaci n o adecuaci n para un prop sito particular Todas las garant as impl citas incluyendo garant as de comercializaci n o adecuaci n para un prop sito particular que no pueden ser excluidas bajo la ley estal est n limitadas a un per odo de uno a o a partir de la fecha de compra HDX no es responsable por da os directos o indirectos incidentales especiales o consecuenciales Si este clavadora de neum tico es usado con fines comerciales esta garant a ser a solamente v lida por noventa 90 d as a partir de la fecha de compra Algunos estados no permiten limitaciones en la duraci n de una garant a impl cita y o no permiten la exclusi n o limitaci n de da os dirctos o indirectos por lo que las limitaciones previamente enunciadas pueden no aplicarse a su caso Esta garant a le otorga derechos legales espec ficos y usted puede tambi n tener otros derechos que var an seg n el estado 22Sp Desempacar 1 Esta herramienta se ha enviado completamente 3 E ensamblada p ADVERTENCIA Si falta alguna pieza no utilices esta 2 Reti id d telah ienta vl osd herramienta hasta reemplazarla De no seguir esta i pean EURO NENE MAMI nba 0 Seles enO2 Oe
41. nauthorized parts of failure of following maintenance instructions may create a risk of injury 3 Use only the lubricants supplied with the tool or specified by the manufacturer 4 Tool service must be performed only by qualified repair personnel AIR SOURCE 1 Never Connect to an air source that is capable of exceeding 200psi Over pressurizing the tool is able to result in bursting abnormal operation breakage of the tool or serious injury to persons Use only clean dry regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air pressure range 2 Never use oxygen carbon dioxide combustible gases or any bottled gas as an air source for the tool Such gases are capable of explosion and serious injury to person OPERATION 1 Do not drive fasteners near edge of material The workpiece may split causing the fastener or ricochet injuring you or people around 2 Do not carry the tool from place to place holding the trigger Accidental discharge could result Choice of triggering method is important Check manual for triggering options 3 During normal use the tool will recoil immediately after driving a fastener This is a normal function of the tool Do not attempt to prevent the recoil by holding the tool against the work Restriction to the recoil can result
42. ng on the bottom ledge of the magazine when loading Make sure the fasteners are not dirty or damaged Push the magazine cover B forward until latch button pops up O Latch button A Magzine Cover B Magzine Rail C WARNING The tool may fire when it is first connected to the air source Always connect the tool to the air source before loading fasteners to prevent injury from unintended cycling Always make sure the tool s magazine is empty at the beginning of each work session before connecting to an air source WARNING Keep the tool pointed away from yourself and others when loading fasteners Failure to do so could result in possible serious personal injury WARNING Use only those fasteners recommended for use with this tool Fasteners not identified for use with this tool by the tool manufacturer are able to result in a risk of injury to persons or tool damage when used in this tool A WARNING Never load fasteners with the workpiece contact or trigger activated Doing so could result in possible serious personal injury HOM EDEP OT COM Please contact 1 800 514 6729 for further assistance Operation Continued 3 Unloading fasteners Unloading is the reverse of loading except always disconnect the air source before unloading WARNING Make sure there is no fastener in magazine before clearing a jam WARNING Always unlo
43. onar lesiones personales graves o la muerte A ADVERTENCIA No se debe utilizar una herramienta que funciona de forma inadecuada No accione la herramienta al menos que se encuentre colocada de forma firme en el lugar de trabajo A 27Sp J Elemento de contacto de trabajo WCE O Ins rez une rang e d attaches dont les tiges O Chevauchent le rail du magasin O Aseg rese de que el gatillo y el elemento de contacto de trabajo se muevan libremente hacia arriba y abajo sin adherirse ni obstruirse O Despu s reconecta la fuente de aire a la herramienta O Presione el elemento de contacto de trabajo hacia la superficie de trabajo sin apretar el gatillo La herramienta no debe funcionar No use la herramienta si la misma funciona sin apretar el gatillo en caso contrario podr an ocurrir lesiones personales O Retire la herramienta de la superficie de trabajo El elemento de contacto de trabajo WCE debe regresar a su posici n original hacia abajo La herramienta no debe funcionar No use la herramienta si la misma funciona cuando se retira de la superficie de trabajo en caso contrario podr an ocurrir lesiones personales Apriete el gatillo y presione el elemento de contacto de trabajo WCE hacia la superficie de trabajo La herramienta no debe funcionar Presione el elemento de contacto de trabajo WCE hacia la superficie de trabajo Apriete el gatillo La herramienta debe funcionar O O
44. onecto Aie ompresor rapido rapido Regulador 4 E 28Sp 295p HOMEDEPOT COM Para obtener asistencia por favor llama al 1 888 514 6729 Soluci n de problemas continuaci n de lo contrario podr an ocurrir lesiones personales graves Cualquier reparaci n o reemplazo debe llevarse a ADVERTENCIA Deje de utilizar inmediatamente la herramienta si se presenta alguno de los problemas descritos a cabo por un t cnico calificado o un centro de servicio autorizado Problema Causa posible Acciones correctivas Fuga de aire en el de la v lvula del gatillo Las juntas t ricas en el armaz n de la v lvula del gatillo est n da adas Cambie las juntas t ricas Fuga de aire entre el armaz n y el borde O Hay tornillos flojos en el armaz n O J untas t ricas da adas O Protector da ado O Apriete los tornillos O Cambie las juntas t ricas O Cambie el protector Fuga de aire entre el armaz n y la cubierta O Tornillos sueltos O Empaquetadura da ada O Apriete los tornillos O Cambie la empaquetadura La herramienta omite colocar sujetadores O Protector desgastado Suciedad en la pieza del borde Hay suciedad o da os que evitan que los sujetadores o el disparador se desplacen libremente en el cargador El resorte del disparador est da ado Flujo de aire hacia la herramienta incorrecto O Desgaste de la junta t rica en el pist n o falta de lubric
45. os limpios y libres de aceite o grasa Usa siempre un pa o limpio para la limpieza Nunca uses l quido de freno gasolina productos a base de petr leo ni solventes para limpiar la herramienta 13 No utilices la herramienta como martillo 14 No utilices esta herramienta de tal manera que los fijadores se dirijan hacia cualquier otra cosa que no sea la pieza de trabajo 15 Nunca utilice gasolina ni ning n otro l quido inflamable para limpiar la herramienta Nunca utilice la herramienta en presencia de l quidos o gases inflamables Los vapores podr an encenderse por una chispa y causar una explosi n que podr a provocar lesiones personales graves o la muerte 16 No retire fuerce ni haga que el gatillo o el seguro del mismo queden inutilizables No haga funcionar ninguna herramienta que se haya modificado de dicha manera en caso contrario podr an ocurrir lesiones personales graves o la muerte 17 No apriete el gatillo a menos que coloque sujetadores Nunca fije el conducto de aire comprimido ni cargue la herramienta mientras aprieta el gatillo La herramienta podr a lanzar un sujetador y provocar lesiones personales graves o la muerte Siempre coloque el seguro del gatillo en la posici n de seguridad cuando no use la herramienta 18 Siempre fije la manguera con un conector o acoplador de manguera sobre o cerca de la herramienta de forma tal que todo el aire comprimido en la herramienta se descargue al momento en que el conector
46. scharge area of the nailer the tool might eject a fastener and could result in death or serious personal injury WORK AREA SAFETY 1 Keep the work area clean and well lighted Cluttered benches and dark areas increase the risks of accidents 2 Do not operate the tool in explosive atmospheres such as in the presence of flammable liquids gases or dust The tool creates a spark which may ignite flammable liquids gases or dust 3 Keep bystanders children and others away while operating the tool Distractions could result in improper use and cause injury 4 Avoid unintentional misfires Always use caution to avoid accidentally firing Do not point towards yourself or anyone whether it contains fasteners or not 1 Do not nail on top of another nail This is able to cause the nail to be deflected and hit someone or cause the tool to react and resultin a risk of injury to persons 2 Remove finger from the trigger when not driving fasteners Never carry the tool with finger on trigger the tool is able to fire a fastener 3 Always wear eye protection Operator and others in the work area should always wear ANSI approved Safety goggles with side shields Eye protection is used to guard against flying fasteners and debris which may cause severe eye injury 4 Always wear hearing protection when using the tool Prolonged exposure to high intensity noise may cause hearing loss 5 Use safety equipment A dust mask non skid safety
47. sido lanzada exam nela atentamente y revise si hay piezas dobladas rajadas o rotas y si hay fuga de aire comprimido NO PROSIGA y rep rela antes de usarla en caso contrario podr an ocurrir lesiones graves 24 Evite usar la herramienta cuando el cargador est vac o Ya que esto puede producir desgaste acelerado en la herramienta 25 Limpie y revise todas las mangueras yconectores de suministro de aire comprimido antes de conectar la herramienta a un suministro de aire comprimido Reemplace las mangueras y conectores da ados o desgastados de lo contrario el rendimiento o la durabilidad de la herramienta podr an verse reducidos 26 No utilices la herramienta si pierde aire o no funciona correctamente 27 No utilices la herramienta si no tiene una etiqueta de advertencia legible 28 Siempre sujeta la herramienta por el mango Nunca la sujetes por la manguera de aire Informac n de Seguridad Continuaci n REPARACI N DE LA HERRAMIENTA 1 Usa nicamente accesorios identificados por el fabricante para ese modelo espec fico de herramienta 2 Al mantener una herramienta la utilizaci n de piezas no autorizadas o el incumplimiento de las instrucciones de mantenimiento pueden aumentar el riesgo de lesiones 3 Usa nicamente los lubricantes provistos con la herramienta o especificados por el fabricante 4 La reparaci n de la herramienta debe ser realizada nicamente por personal calificado FUENTE DEL AIRE 1 Nunca
48. uente de aire antes de cargar los fijadores para evitar lesiones causadas por ciclos accidentales 26Sp 4 C mo retirar sujetadores atascados En ocasiones un sujetador puede atascarse en el mecanismo de disparo dejando la herramienta inoperante Para retirar el sujetador atascado siga los siguientes pasos O Desconecta la herramienta de la fuente de aire O Retire los sujetadores de la herramienta No hacerlo podr a provocar que los sujetadores se expulsen desde la parte frontal de la herramienta O Retire completamente los tornillos peque os del extremo D y la placa superior del extremo E para detectar el sujetador atascado O Tenga cuidado de no doblar o da ar la hoja si es necesario use pinzas o un destornillador para limpiar el sujetador atascado O Vuelva a colocar la placa superior del extremo E en el extremo F ajust ndola con los tornillos D O Despu s reconecta la fuente de aire a la herramienta O Vuelve a cargar la herramienta con fijadores Placa superior el extremo F Placa superior E Tornillos D ADVERTENCIA Aseg rese de que no haya sujetadores en el cargador antes de retirar un sujetador atascado ADVERTENCIA Desconecte la herramienta de la fuente de aire cada vez que retire un sujetador atascado Luego de desconectar la herramienta del compresor de aire deber a haber suficiente presi n de aire para disparar Luego de desconectar la manguera de
49. ujete la manija firmemente y permita que la herramienta realice el trabajo No seguir esta advertencia puede provocar graves lesiones personales 4 No coloques fijadores sobre otros fijadores o con la herramienta a un ngulo demasiado inclinado ya que esto puede causar el desv o de los fijadores y provocar lesiones 21Sp 5 No uses la herramienta a menos que pretendas colocar un fijador en la pieza de trabajo 6 Opera siempre la herramienta con cuidado O Respeta la herramienta como implemento de trabajo O Nunca la uses en bromas y juegos Nunca jale el gatillo a menos que la punta est orientada directamente hacia el trabajo O Mant n a los dem s a una distancia segura de la herramienta ya que puede accionarse accidentalmente y posiblemente causar lesiones ENTRADA DE AIRE Y CONEXIONES 1 El conector de la herramienta no debe estar bajo presi n al desconectar la entrada de aire Si se utiliza un acoplador incorrecto la herramienta puede quedar cargada de aire luego de la desconexi n y podr a disparar fijadores incluso con la l nea de aire desconectada y ello puede causar lesiones 2 No utilice ning n tipo de gases reactivos lo que incluye pero no se limita al ox geno o a gases combustibles como fuente de alimentaci n Use nicamente aire comprimido filtrado lubricado y regulado El uso de gas reactivo en lugar de aire comprimido puede hacer que la herramienta explote lo cual producir a lesiones
Download Pdf Manuals
Related Search
Related Contents
VX-3E ITA Lenovo ThinkPad T430 “リスクを未然に防ぐためのさまざまなマネジメント Samsung NP940X3GI User Manual (Windows8.1) MANUEL D`INSTALLATION AIR CRÉATION SERIE JUMBO Copyright © All rights reserved.
Failed to retrieve file