Schlage BE479AA V CEN 619 Installation Guide
Contents
1. This lock may be rekeyed to match other locks in a residence Contact a locksmith for assistance WARRANTY Lifetime Limited Mechanical and Finish Warranty and 3 Year Limited Electronics Warranty Subject to the terms and conditions of the warranty Schlage extends a lifetime limited mechanical and finish warranty and a three year limited electronics warranty to the original consumer user Original User of our Schlage brand product Product against defects in material and workmanship as long as the Original User occupies the residential premises upon which the Product was originally installed See answers schlage com for specific warranty details and limitations or contact Schlage Customer Service at 888 805 9837 in the U S and Canada or 800 506 7866 in Mexico for assistance FCC IC Statement FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and Used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference2. SCHLAGE SENSE Smart Deadbolt User Guide Setup Code Setup Code Setup Code Default Codes C digos de predeterminado Codes du d faut PLEASE KEEP CONSERVE VEUILLEZ THIS GUIDE ESTA GUIA CONSERVERCE You will need iNecesitara these codes to estos c digos Vous aurez besoin de operate your lock para operar la ces codes pour faire cerradura fonctionner la serrure GUIDE IL 7 l 3 Schlage Sense E User Guide Contents ole E A 3 Manual Programming Guide 8 Lock PartSixticscecssccccsztccacceseeccaceteses 4 Programming Procedures 8 Setup Code and Default Access My Codes e ANERER 10 CodeS A E none 4 BESHRCHCE SSAA AE 10 Locking and Unlocking 5 Troubleshooting sccssscensseensees 12 Cleaning the LOCK sccssssesnsees 6 Factory Default Reset 14 Replacing the Batteries 6 Emergency Key Override 14 Manual Programming Guide 7 A eeaeee aeee eeaeee eeaeee 15 Programming Descriptions i FeG 7G Sialenniegitve cee eee 5 Questions about your new Schlage Sense Smart Deadbolt Please don t return it to the store Let us help you first Contact Us For technical documents and a Lanes 2 Y videos visit schlage com a ae eee ee oe gt or the Help Center in the a 018005067866 Schlage Sense app Document your purchase and register your warranty at Schlage com register or register using the app
3. Code Add 4 8digits y 4 8 digits another access e code V 2blinks 2 beeps Enter Enter Same Unwanted Unwanted Delete AccessCode Access Code another Success access Yo 2blinks code 2 beeps Enter New Enter Same New Programming p rogramming Code Code Success Yo 2 blinks 2 beeps Enable 1 blink beep Disable 2 blinks 2 beeps Enter WARNING Programming Removes all Code access codes from the lock Access SUCCESS codes cannot be 2 blinks retrieved after they ZEE are deleted ENABLE DISABLE 1 TOUCH LOCKING Press Press Enter Programming ed Programming V indicator light solid 2 blinks 2 beeps CHANGE ACCESS CODE LENGTH Press Enter Press Enter Enter Same WARNING u Programming Desired Desired Changing Q Code 8 AccessCode AccessCode the access ih Length Length ere fa T Programming Success ail a indicator light Yo Yo 2 blinks access solid 2beeps codes ENABLE DISABLE AUTO LOCK Press Enter Press Programming ade 9 Programming Yo indicator light solid 2 blinks 2 beeps TEMPORARILY DISABLE AUTO LOCK Deadbolt should be locked to begin Press Enter Within 5 seconds AccessCode manually lock Y andunlockthe deadbolt using the 1 Dlink thumbturn 1beep RESTORE AUTO LOCK Relockthe deadbolt 4 using the thumbturn 2 blinks 2 beeps Alarm features can be programmed using the app Using the app Just follow the instructions in t
4. the chosen settings Alarm can be programmed in the app Bolt Automatically extends and retracts when the lock s touchscreen is used Manually extends and retracts when the thumbturn is rotated Setup Code and Default Access Codes The programming code and default access codes are located on one sticker and the Homekit setup code is located on the other sticker Back of the Alarm 9 You must remove the alarm from the door to see these stickers Front of this user guide CHLAGE SENSE Smart Deadbolt with Bluetoot User Guide SCHLAGE Model AL24529992 Programming Code XXXXXX User Code A XXXX User Code B XXXX BE375 FW Ver 1 0 13 03132014 OURAN 00000214 5580292 002 THIS IMAGE DOES NOT REFLECT THE CURRENT STATE OF THE CODE LABELS LOCKING AND UNLOCKING You can lock and unlock your door with a simple press using the Schlage Sense app FROM THE OUTSIDE To Lock To Unlock Press the Schlage Button Press the Schlage Button 2 The lock will lock The green 2 Enter a valid access code check mark will light once 3 The green success check mark will flash twice and one beep will sound The deadbolt will Unlock m Z Q E un L pe 7 A ho O If the bolt cannot fully extend O If the red error X lights the th
5. ack of the Alarm Assembly before beginning Default Programming and access codes will be restored All existing access codes and current Programming Code will be erased CUSTOMER SERVICE CANNOT RETRIEVE LOST DEFAULT CODES DO NOT RESTORE FACTORY SETTINGS UNLESS YOU CAN LOCATE THE DEFAULT CODES See Setup Code and Default Access Codes on page 4 I Y 6 Z Lu Using the app delete the lock The app will attempt to return the lock to factory default settings If successful the touchscreen will flash the green check mark Continue to step 5 below Disconnect the batteries See Replacing the Batteries on page 6 2 Press and hold the Outside Schlage Button 3 While holding the Outside Schlage Button reconnect the batteries 4 Release the Outside Schlage Button O If you are moving the lock to a new door install the lock on that door before continuing 5 To check that the lock was reset press the Outside Schlage Button and enter one of the default access codes See Setup Code and Default Access Codes on page 4 6 If the reset was successful the lock will perform a setup routine Wait until the bolt stops moving The reset and setup are complete EMERGENCY KEY OVERRIDE Emergency Key Override can be used when the battery is completely dead or when no valid access code is known Insert key and rotate to unlock just like any lock See Replacing the Batteries on page 6
6. cuit board You may damage the lock Remove the inside cover 2 Unsnap the battery 3 Replace the battery connector remove tray with the batteries the battery tray and facing the door Snap replace the batteries the battery connector to the tray and replace the cover Lithium Batteries Lithium batteries may have a longer life but when they begin to fail they A fail quickly We don t recommend them because they don t give you a lot of time to change your batteries before the lock is completely dead MANUAL PROGRAMMING GUIDE Use the app to easily program your lock NOTE Existing access codes will be deleted when you configure your lock with the app Schlage recommends using the Schlage Sense mobile app to program your lock If you don t have the Schlage Sense app you can use the manual programming instructions below after pairing using the mobile app You must perform a Factory Default Reset to program your lock manually WARNING Manual programming functions are NOT available m Z Q E 1 L Outside Schlage Button e The first button Red X lf there is a problem during programming you will press in the programming process Can also be pressed to exit programming you will see the red error X immediately Programming Indicator Green Chec
7. dbolt Within 5 seconds manually lock and unlock the deadbolt using the thumbturn Restore Lock the deadbolt using the thumbturn Auto Lock MANUAL PROGRAMMING GUIDE Programming Procedures 9 Programming mode will automatically time out after 30 seconds of inactivity gt If you make a mistake during programming press the outside Schlage button to leave Programming mode and start over Write your programming code here for easy access I L 6 Z Lu ADDING ACCESS CODES WARNING Manual programming functions are NOT available after pairing using the mobile app You must perform a Factory Default Reset to program your lock manually Determine how long you want your access codes to be BEFORE adding any access codes If you change the access code length all existing access codes will be deleted Press Press Enter Programming Code 1 Programming indicator light solid V DELETING ACCESS CODES Press Enter Press Programming Ed 2 Programming indicator light solid V CHANGING THE PROGRAMMING CODE Press Press Enter Programming ode 3 Programming indicator light Yo solid ENABLE DISABLE BEEPER Press Enter Press Programming Code 5 Programming indicator light solid V Beeper will still sound during programming DELETE ALL ACCESS CODES Press Enter Press Programming Code 6 Programming indicator light solid V Enter New Enter Same Access New Code Access
8. e 1 Touch Locking feature is not Schlage button enabled See lock settings in Schlage when deadbolt is Sense app unlocked does not If you do not want to enable Lock amp cause deadbolt to Leave then enter a valid access code relock to lock the door Deadbolt will not long 1Red X Adjust bolt frame alignment Browse extend orretractas beep to answers schlage com for help expected Deadbolt requires Greeny Deadbolt frame alignment is marginal Adjust door frame for best operation Browse to answers schlage com for help The bolt has become soiled Clean with mild detergent and warm water The strike has become worn Flip the strike over for continued smooth operation These features are not available using manual programming if your lock has been paired using the Schlage Sense mobile application m Z Q E Wn L FACTORY DEFAULT RESET When should you perform a Factory Default Reset If you want to move the lock to a different door you need to restore default settings move the lock to the new door and then set up the lock again If you have forgotten your Programming Code you can restore the default codes If you have set up your lock using the mobile app and would like to force the lock to unpair from all mobile devices erase all codes and restore the factory default settings and default codes WARNING Locate the default Programming and access codes on the front of this guide or the b
9. e red X will light and a tone access code was not valid will sound The door may remain unlocked FROM THE INSIDE To Lock To Unlock Rotate the Inside Thumbturn Rotate the Inside Thumbturn The Inside Schlage Button will not lock or unlock the deadbolt It is used to silence the built in alarm See the alarm settings within the Schlage Sense app CLEANING THE LOCK In order to properly clean the touchscreen from build up of dirt oils or other contaminates you should use a mild dish soap with warm water and follow the general rules below Do rinse the touchscreen with warm water prior to cleaning process Do follow the application of soap with a damp lukewarm cloth Don t use abrasives high alkaline cleaners or gasoline Don t leave cleaners on touchscreen for long periods wash immediately Don t apply cleaners in direct sunlight or at elevated temperatures Don t use Scrapers squeegees or razors The bolt itself can be cleaned using a mild dish soap and warm water This can help improve decreased performance REPLACING THE BATTERIES Replace the batteries in your lock at the same time each year that you test and replace the batteries in your smoke alarms This will ensure continued reliable operation I L l 6 Z Lu 9 Use four high quality alkaline AA batteries for replacement WARNING ELECTROSTATIC DISCHARGE DO NOT TOUCH the cir
10. e security 10 ENGLISH I vi l O Z Lu Problem Sounds Lights TROUBLESHOOTING Solution forgot my Programming Code Check the front of this guide or the back of the Alarm Assembly for default Programming Code If needed restore lock to factory settings See Factory Default Reset on page 14 need to delete an access code that don t remember Delete all access codes Then add all needed access codes back into the lock See Delete ALL Access Codes on page 8 Cannot add a new access code Cannot delete an access code Cannot change Programming Code Cannot delete all access codes 2 beeps Yellow dot flashing 2 Red X Yellow dot flashing was not pressed after entering Programming Mode 30 access codes already exist Delete an access code before adding a new one See Deleting Access Codes on page 8 Second access code entry did not match first access code entry The new access code matches the first 4 6 digits of the existing Programming Code 2 was not pressed after entering Programming Mode 2 beeps 2 Red X Yellow dot flashing First access code entered did not match any current access code Second access code entered did not match first access code entered 3 was not pressed after entering Programming Mode 2 beeps 2 Red X Yellow dot flashing Second Programming Code entered did not match
11. first Programming Code entered First 4 6 digits of new Programming Code match an existing access code 6 was not pressed after entering Programming Mode The 2nd Programming Code entered was not valid Access code does not unlock lock l beep 1 Red X Access code entered is not a valid access code two attempts to lock or unlock The bolt was operating smoothly but now is not Problem Sounds Lights Solution Backlighting does Batteries are completely dead and not come on when no electronic operations are possible Outside Schlage See Replacing the Batteries on page button is pressed 6 and access code cannot be entered The battery tray is not connected The cable that runs through the door is not connected Remove the Alarm Assembly and check the connection See Step 8 of the Touchscreen Deadbolt with Alarm Installation Instructions for help After entering an Several Outside Battery is low and should be replaced access code to beeps yellow See Replacing the Batteries on page unlock the lock dot 6 the yellow dot is flashing flashing and there is a delay before unlock Inside Schlage Inside Button is flashing Schlage but no alarm is Button sounding flashes every 5 seconds 3 Red X when 3 Red X Battery is critical and must be Outside Schlage replaced See Replacing the Button is pressed Batteries on page 6 Pressing Outside Th
12. gt Please keep this guide This guide contains important information about your lock Default access codes Homekit setup code and Programming codes are located on the stickers on the front of this guide You will need these if you ever need to reset your lock back to factory default settings The sticker also contains your serial number which may be needed for warranty and customer service support m Z Q E un I Instructions for adding and deleting access codes changing the lock behavior troubleshooting customer service and more are explained in this guide LOCK SETUP Follow these steps to get your lock set up and ready to use using the application You can use the app to set up your lock step by step and access installation videos l Download the app Just search for Schlage Sense in the App Store Once you connect your lock to your app the manual programming functions disabled and any access codes are deleted 4 Download on the Works with a App Store Apple Homekit Apple Homekit technology provides an easy secure way to control your home s lights doors thermostats and more from your iPhone iPad or iPod touch Homekit requires an iPhone iPad or iPod touch with iOS 8 1 or later gt DON T WANT TO USE THE APP Go to page 7 for manual programming instructions 2 install your lock Follow installation instructions in separate booklet or access the step by step installati
13. he Schlage Sense application These manual programming instructions will not work if you set up your lock with the app I vi l O Z Lu MY CODES Use the Schlage Sense app to record and keep track of your access codes If you are not using the Schlage Sense app use these tables to record programming and access codes that you program into the lock gt Use a pencil to enter the codes in the boxes so you can easily change them later The Programming Code can be any combination of six numbers entered into the keypad to put the lock in Programming Mode The first 4 6 numbers depending on access code Length must be different from all of the access codes currently in the lock One Programming Code is programmed into the lock by default This code can be found on the stickers one on the back of the Alarm Assembly and one on the back of this guide Access Codes gt gt Up to 30 access codes can be stored in the lock at one time An access code can be any combination of 4 8 digits entered into the keypad to unlock the lock The first 4 6 digits must be different from the first 4 6 digits of the Programming Code Two access codes are programmed into the lock by default These two codes can be found on the stickers one on the back of the Inside Alarm Assembly and one on the back of this guide Best Practices Give each person their own unique access code Change access and Programming Codes periodically to ensur
14. installation ou programming don t return your de la programmation ne Schlage Sense to the store retournez pas votre serrure Our Schlage Customer Service Schlage Sense au magasin representatives are ready to help Les repr sentants du service a la client le de Schlage sont a votre service Sans frais 888 805 9837 answers schlage com Toll free 888 805 9837 answers schlage com Si tiene dudas acerca de cualquier parte de la instalaci n o programaci n no devuelva su Schlage Sense a la tienda Nuestros representantes del Departamento de Servicio de Asistencia al Cliente de Schlage est n listos para ayudarlo Toll free 3888 805 9837 answers schlage com A NEW KIND OF KEYLESS O Allegion 2015 E E Printed in U S A WN P516 991 P516 991 Rev 07 15 b ALLEGION
15. k Mark key is pressed and when a function is complete e Blinks when a number Blinks when Programming Mode is entered e Solid while a programming function is being performed Programming Descriptions Add Access Code Access codes unlock the deadbolt Can be 4 8 digits long All codes must be the same length See Adding Access Codes below Delete Access Code Removes one access code at a time Change The Programming Code is used to put the lock into Programming Code Programming Mode It is 6 digits long Enable Disable The beeper can be turned off if desired Beeps will still Beeper sound during programming Delete ALL Access Removes ALL access codes from the lock Codes Enable Disable When enabled Press the Outside Schlage Button to lock 1 Touch Locking the deadbolt Default setting When disabled Press the Outside Schlage Button and then enter an access code to lock the deadbolt Change Access Access codes can be 4 8 digits in lensth Default is 4 Code Length digits Changing the access code length will delete all existing access codes Enable Disable When enabled the lock will automatically relock 30 Auto Lock seconds after unlocking Disabled by default Temporarily Auto Lock must already be enabled While the deadbolt is Disable locked press the Outside Schlage Button and then enter Auto Lock a 4 8 digit access code to unlock the dea
16. lent isotropically radiated power e i r p is not more than that necessary for successful communication Conform ment aux normes d Industrie Canada ce transmetteur radio ne peut fonctionner qu avec une antenne dont le type et le gain maxiumum sont approuv s par Industrie Canada Pour r duire les risques d intef rences radio encourus par d autres utilisateurs le type et le gain de lantenne doivent tre choisis de facon a ce que la puissance rayonn e isotrope quivalente PIRE ne soit pas sup rieure a celle n cessaire pour tablir une bonne communication This Device complies with Industry Canada License exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Cet appareil est conforme norme Industrie Canada RSS exempts de licence s Son fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne doit pas provoquer d interf rences et 2 cet appareil doit accepter toute interf rence y compris les interf rences pouvant provoquer un fonctionnement ind sirable de l appareil Apple iPhone iPad iPad Air and iPod touch are trademarks of Apple Inc registered in the U S and other countries Homekit is a trademark of Apple Inc If you have questions about Si vous avez des questions any part of installation or a propos de l
17. on video on the app 3 Pair your lock with your iPhone iPad or iPod touch Pair your lock using the Schlage Sense app for easy management 4 Add access codes to your lock After adding your lock to your home use the app to add codes to unlock your lock 5 Configure the alarm and other lock features The Schlage Sense Smart Deadbolt includes many features that you can configure using the Schlage Sense app LOCK PARTS DOOR EXTERIOR Touchscreen DOOR INTERIOR Alarm Outside Schlage Button Alarm Speaker ES Inside Schlage WS Touchscreen Button A Cylinder Thumbturn AN g aN lh ky See Emergency Key Override on page 14 IL 7 D Z Inside Schlage Located on the inside of the door ui Button Used to silence the alarm Does not lock or unlock the door Thumbturn Used to lock and unlock manually from the inside Outside Schlage Located on the outside of the door Button Locks the deadbolt with 1 Touch Locking Illuminate the lock s touchscreen for access code entry Touchscreen Remains unlit until a button is pressed Located on the outside of the door Used to enter access codes Used to lock door default setup Cylinder Used to unlock in emergency situations Alarm Speaker Sounds alarms based on
18. to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment m Z Q E Wn I RF Exposure To comply with FCC IC RF exposure requirements for mobile transmitting devices this transmitter should only be used or installed at locations where there is at least 20 cm separation distance between the antenna and all persons Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equiva
Download Pdf Manuals
Related Search