MESA MAWS2113ECSD Instructions / Assembly
Contents
1. 4 14 x 21 1 8 Wall cutout Page 5 INSTALLING THE WALL SAFE To make the safe installation as easy as possible you can remove the door see the next page for instructions Note DOOR REMOVAL IS OPTIONAL 1 Install your wall safe into the wall so that the hinge side of the safe is flush against the right hand stud and the front flange is flat against the wall Mark the stud using the 4 outer slots in the front piece of the wall safe to indicate where the pilot holes need to be drilled 2 Remove wall safe and drill 1 16 1 8 diameter pilot holes 3 Now that the pilot holes have been drilled you can fasten the safe into the wall Use 4 sets of HARDWARE D through the 4 outer slots in the front piece of the wall safe Note Do not over tighten there may be a little gap between the left hand stud and the safe this is normal 4 Install expandable shelves as needed Mark the stud Install hinge side first use the outer slots Drill pilot holes REMOVING THE DOOR OPTIONAL To make the safe installation as easy as possible you can remove the door IMPORTANT Secure the door while removing the top hinge pin in STEP 3 because once the pin is removed the door will no longer be secured to the safe 1 Removethesetscrews located on the top and bottom hinge 2 Remove the first all thread screw in the bottom hinge using a 6 millimeter allen wrench and back out the second all thread screw Also remove2. SAFE MODEL MAWS2113E OPERATING amp INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Parts Hardware Check LISt rr rrrr cirie 1 Quick Sta i i i i ina 2 Quick Installa i dina 2 Override KEY System 2 Changing Baveries iii ii e i a b i EEA 2 How to Operate Your Safe ss sssssseennnnnnnennnnnnnnnennnnnnnnnnnzzznnnnnen 3 Programming A a d i jda A 3 IMENO LIG Dt a i cl alia 3 Adjusting amp Securing Telescoping Back gt 4 Shelf Extensions sonic bee ets asennad tae eee ee aed eek ence eae eee alia 4 Choosing Install LOocatlon iii ii iii g ami ai 4 Wall Cutoub glieli a a i dduqdti 5 installinq Wall Safe i iii declassata 6 REMOVING the Door i i aid 6 Dear Valued Customer Congratulations on vour choosing Mesa Safe to protect vour valuables Xou have made an excellent choice in vour securitv measures Mesa Safe Companv has built a solid reputation on integritv and quality craftsmanship We pride ourselves in having the best products in the industry and consistently exceeding customer expectations Your Mesa Safe product comes with a support team and warranty in place that is second to none We have the most qualified safe technicians ready to assist you should you have a problem with your unit Please read and understand the operating instructions of the unit this will ensure maximum efficiency and usability Please visit www mesasafe com and see the dive
3. on for 5 seconds INVALID CODE The keypad BEEPS 6 TIMES while the ORANGE LIGHT turns on after entering a code LOCKOUT PENALTY If an incorrect code is entered three times in a row then you will activate the lockout period During the lockout period the keypad will not respond and the ORANGE LIGHT WILL FLASH EVERY SECOND until the lockout period is over The lockout period will last for approximately 3 MINUTES PROGRAMMING 1 Open your safe and locate the red program button on the inside of your door 2 Press the red program button and release and the keypad will beep once and the orange light on the keypad will turn on for 10 to 15 seconds 3 Before the orange light turns off enter your new 3 to 8 digit code and confirm by entering the B key VALID RESPONSE 4 BEEPS 4 TEST YOUR NEW CODE 3 or more times before closing the door and write down your combination 5 Ifa mistake has been made wait for the orange light to turn off and repeat steps 1 4 INTERIOR LIGHT PROGRAMMING SWITCH BUTTON iii BATTERV ii COMPARTMENT Ir j7 7 3 4 LOCKING BOLTS INTERIOR LIGHT BACK PANEL LOCATED ON THE INSIDE OF THE DOOR INTERIOR LIGHT The interior light is controlled bv a switch located on the top edge of the door s back panel NOTE Alwavs remember to turn the light off before closing the door or it will drain batteries If batteries do get drained when the safe is locked use your override kevs Page 3 INSTALLA
4. the ball bearing 3 Removethe top hinge pin by tapping it out with a wedge screwdriver 4 Reverse the directions to re install door Hinge Remove top hinge set Remove first all thread Remove top hinge screw screw on bottom hinge pin Bottom Hinge Remove bottom hinge Back out 2nd all thread set screw screw on bottom hinge Page 6 Better MESA SAFE than Sorry MESA SAFE COMPANY P O Box 52282 Irvine CA 92619 Phone 714 891 8356 Fax 714 891 8474 www mesasafe com sales mesasafe com
5. TION SECTION age amp SECURING THE TELESCOPING BACK Using 6 sets of HARDWARE C attach the middle section of the telescoping back first Keep screws loose enough so the depth can be adjusted 2 Using 6 sets of HARDWARE B attach the back section of telescoping back Keep screws loose enough so the depth can be adjusted 3 Now that both sections have been attached determine the maximum depth available in your wall 4 Adjust amp secure both sections of the telescoping back to the determined depth Do not over tighten screws t FRONT SECTION ATTACHING THE ATTACHING THE MIDDLE SECTION BACK SECTION BACK SECTION FLANGE FLANGE FLANGE INSIDE OF INSIDE OF WALL SAFE WALL SAFE MIDDLE SECTION SHELF EXTENSIONS Your wall safe comes with shelf extensions The shelf extensions come in 2 sizes install the shelf extensions that work best with your depth We recommend installing the shelves after the safe has been installed into the wall When using the larger shelves you can install the shorter shelves to add extra support under the large ones Use 2 sets of HARDWARE A for each shelf extension CHOOSING THE LOCATION IMPORTANT Be sure to pick a wall free of plumbing pipes and electrical wires Use caution when cutting into drywall The wall safe is 14 wide and is designed to fit between standard 16 center to center wall framing Note Most homes have wall framing construction of 2x4 s and or 2x6 s that a
6. re located 16 from center of stud to center of stud TOOLS REQUIRED FOR INSTALLATION Tape Measure Pencil Drill Dry Wall Saw or Jig Saw Framing Square Screwdriver Phillips amp Flathead Flashlight 6mm Allen Wrench For door removal NOTE Instructions shown are for wood framed wall installation WALL CUTOUT 1 Determine the approximate location of the stud for the right hand side of your wall safe hinge side Drill or cut a large enough pilot hole to determine where the inside edge of the stud is located Using a framing square draw a 21 1 8 vertical pencil line along the inside edge of the stud This will locate the right hand hinged side of the safe From the top of your scribed line measure 14 to the left and make a pencil mark Repeat this step at the bottom of your scribed line Using a framing square draw a vertical line between the pencil marks locating the left side of your safe With the framing square draw a horizontal line at the top of the 21 1 8 measurement joining the 2 vertical lines Repeat this step at the bottom You now have a 14 x 21 1 8 rectangle scribed on the wall between the studs With the dry wall saw or equivalent tool starting at the pilot hole cut along the pencil lines and remove the wall section NOTE The outer flange will cover the cut line I 21 1 8 Pilot Hole I I l I I I l I l I l I I I l I Stud 5 pnjg
7. rse selection of products available to meet your security needs Thank you for choosing Mesa Safe Company Better MESA SAFE than Sorry PARTS HARDWARE CHECK LISTS INLCUDED WITH SAFE A 8 Phillip Head Screw M5 8 x 5 16 nut amp 2 washers Cl B 6 Phillip Head Screw M5 8 x 7 16 nut amp 2 washers Jo C 6 Phillip Head Screw M5 8 x 13 16 nut amp 1 washer D 4 Lag BON 1 4 x 2 amp 1 washer 1000 D e E 2 Override Key Fl IN G F 2 Large Shelf Extension G 2 Small Shelf Extension WOOO foo Bi H 4 AA Batteries A C E H Page 1 IMPORTANT DO NOT RETURN SAFE TO STORE If you are missing parts have difficulty programming or opening your safe please contact Technical Support at 1 800 490 5624 for assistance NOTE Test your wall safe s lock operation before installation QUICK START 1 Install the 4 AA batteries that is included with your safe 2 Enter 1 5 9 A on the keypad and the green light will turn on for 5 seconds 3 Pull the handle while the green light is on and open door 4 If you misplaced your combination or if the batteries die while the safe is in the locked position use the override key that is included with your safe DO NOT STORE THE OVERRIDE KEYS INSIDE SAFE SE INSTALL DETAILED INSTRUCTION ON PAGE 4 Choose a location free of plumbing and electrical wires Adjust and secure the telescoping back Locate studs safe designed to fit between standard 16 cen
8. ter to center studs Cutout a 21 1 8 High x 14 wide section in your wall Remove door Optional Mark and Drill 1 16 1 8 pilot holes into studs Anchor your wall safe Install shelf extensions if needed DOLO OVERRIDE KEY SYSTEM For your convenience we have engineered a manual override key system for your safe If you forgot or misplaced your combination or if the batteries die remove the plastic cap located below the keypad Insert the key and turn counter clockwise Pull the chrome handle This will manually open your safe Two keys included CHANGING BATTERIES The battery compartment is located on the inside of the door If the batteries die while the safe is locked please use the mechanical override keys provided to gain access into your safe Safe runs on 4 AA BATTERIES LOW BATTERY WARNING If the batteries are low the RED LIGHT will illuminate or the SAFE WILL NOT UNLOCK after entering the correct code Page 2 YOUR SAFE IS PRESET TO CODE 159 Set the lock to your own unique code immediately this is highly recommended HOW TO OPERATE YOUR SAFE 1 Enter your code on and then enter A the GREEN LIGHT will turn on 2 Pull the handle before the GREEN LIGHT turns off and open the door 3 To lock the safe close the door and push handle back to the closed position 4 ALWAYS CHECK YOUR SAFE always assure it s locked before walking away VALIDE CODE The GREEN LIGHT on the keypad will turn
Download Pdf Manuals
Related Search