LockState LS-19EPL Instructions / Assembly
Contents
1. www LockState com OPERATING INSTRUCTION for LockState Safe LS 19EPL CAUTION Do not keep the keys in the safe Thank you for purchasing the Lockstate LS 19EPL hospital safe This safe will install easily on floors walls or in closets This easy quick start quide will help you through the installation and programming process 1 OPENING THE SAFE THE FIRST TIME Use a screw driver to pry off the round plastic cover situated to the right of the keypad see A in diagram 1 exposing the keyhole underneath Insert the key into the keyhole and turn it clockwise to retract the bolts and open the safe door You can follow these steps to manually open your safe anytime Note that the motor will NOT work when the override key is in the keyhole and the safe is in the UNLOCKED status In this case the LED display will read Error To remove the override key with the door open turn the key counter clockwise and take it out 2 INSTALLING THE BATTERIES The safe requires 4x size AA 1 5V batteries To install the batteries open the safe remove the battery cover plate on the back of the door A in Diagram 2 and install the batteries Make sure the batteries are inserted with the correct corresponding polarity Use of alkaline batteries is recommended 3 PROGRAMMING THE CODE All safes are supplied with the factory preset master code 888888 After inserting the batteries you can open the safe with this master code by2. ING THE BATTERIES The safe requires 4x size AA batteries To replace the batteries open the safe remove the battery cover on the back of the door and replace the old batteries Make sure the batteries are inserted with the correct corresponding polarity After changing the batteries the user code of the system will revert back to the factory preset user code 000000 However the current master code will remain in memory Use of alkaline batteries is recommended 8 OVERRIDE INSTRUCTION TO OPEN THE SAFE MANUALLY For your convenience this safe has a manual override system in case you forget your combination or the batteries die To open the safe manually use a screw driver to pry off the round plastic cover situated to the right of the keypad see A in diagram 1 exposing the keyhole underneath Insert the key into the keyhole and turn it clockwise to retract the bolts and open the safe door Note that the motor will NOT work when the override key is in the keyhole and the safe is in the UNLOCKED status In this case the LED display will read Error To remove the override key with the door open turn the key counter clockwise and take it out 9 INSTALLING THE SAFE This safe can be secured to the floor on a wall or in a closet There are pre drilled holes in both the bottom and the back of the safe for mounting To secure the safe with the safe door open hold the safe over the exact spot where it will be mounted and
3. ade to open the safe with incorrect codes the keyboard will be disabled for 5 minutes and the display will read ERROR 1 2 3 and then HOLDOS In this case it is still possible to open the door with the emergency override key and doing so will nullify the 5 minute waiting period and reset the safe to immediately accept keypad codes 5 CODE DISPLAY AND BUZZER CONTROL Display control By pressing the C key and the 3 key at the same time you can set the LCD display to either show the code as it is entered or not show the code as it is entered When display reads dP the codes will not display when entered When the display reads dPCodE codes will display when entered Buzzer sound control By pressing the C key and the 6 key at the same time you can turn on or off the the buzzer sound when the safe is opened When the display reads bUZZEr the buzzer will sound When the display reads SILENT the buzzer will not sound 6 BATTERY REPLACEMENT WARNING To test the batteries press the E key If the batteries are good the display will show HI BAT If the batteries are low the display will show LO BAT and you should replace the batteries NOTE When the batteries are low each time the safe is opened the display will read OPEN and Lo bAT alternating Also when the batteries are low each time the safe is closed the display will read CLOSE and Lo bAT alternating 7 REPLAC
4. entering 888888 and then pressing the E key The door will automatically open Programming a new master code A With the door either open or closed press the 0 key 2 times then press the E key The display will read SELECT B Now press the 1 key and the display will read OLD C Enter the master code that was previously programmed for new safes this code is 888888 and press the E key The display will read SET D Enter a new Master code a minimum of 3 digits and maximum of 6 digits and press the E key The display will read REPEAT E Again enter the new master code and press the E key The display will read DONE and your new master code is set Programming the user code Locking the door A With the door open enter a user code a minimum of 3 digits and maximum of 6 digits B Now push the door shut locking bolts are still unlocked and hold the door closed while pressing the E key You will hear the locking bolts lock the door automatically indicating that your new user code has been programmed NOTE While the master code remains set until it is changed using the master code change procedure the user code will automatically be deleted if the safe is opened even one time with the user code 4 OPENING THE SAFE Enter either the user code or the master code and press the E key The door will be automatically open NOTE If 3 attempts are m
5. use a pencil to trace the pre drilled holes on the floor or the wall Remove the safe and drill a hole in each marked spot and insert the anchors into the drilled holes Now again place the safe where it will be mounted door open and screw in the mounting bolts into the anchors in the drilled holes from the inside of the safe
Download Pdf Manuals
Related Search