Surebonder FPC9630-350-3 Instructions / Assembly
Contents
1. DRIVE FIM KIT no no no 3630 71 SPACER STOPPER 3630 72 TZ TE TT T3 wg 31 SCREW 420 TALL COVER MAIL TAME SPACER 9630 76 3630 77 STEEL BAR STOPPER 3630 73 FARNT PART 3630 79 HEAD VALVE FISTOM SET TRIGGER VALVE SETT TRIGGER SET 9630 31 no 5630 53 83 a4 3630 54 MAIL TANE ASSY 36240 55 25 Kit Prices www surebonder com Call tor Price 5600 400 SEAL EIT Call for Price DRIVE FIM KIT 5600 420 FASTENER EIT 3600 410 Call for Price Preparing for Use lf the stapler has been stored in a cold environment bring it to a warm area and allow it to warm up before using Important Keep lubricator filled with pneumatic oil after each use or after using 3 4 strips of staples Loading Make sure stapler is disconnected from air supply Only use the proper size and type of staple with this stapler as specified under Staples Depress the track release lever to release the spring loaded staple magazine slide the magazine out back as far as it will go Turn the stapler upside down Place a full strip of staples into the staple magazine with the staple points facing upward away from the tool Slide the staple magazine closed until the track release lever snaps back into place with a click Closing the staple magazine while staples are loaded engages the spring load mechanism so it will take slightl2. SUREBONDER WARRANTY Model 9630 Pneumatic Stapler If you have any problems with this tool please call FPC Corporation toll free at 1 800 860 3838 before returning it to the place of purchase FPC Corporation warrants this tool to be free from defects in material and workmanship under normal conditions of use and when used in accordance with FPC operating instructions for a period of 90 days from the date of purchase by the user Within the 90 days warranty FPC at its option shall repair or replace tool The stapler must be returned at the distributor user expense either within warranty or out Repaired or replaced tools will receive a 60 day warranty USER MUST BE USING THE PROPER STAPLES FOR THIS WARRANTY TO BE VALID WARRANTY IS VOID IF INCORRECT TYPE OF STAPLES ARE USED Uses 18 SUREBONDER auge 350 series 5 8 thru 1 9 16 and most 18 gauge 1 4 crown staples Operating Instructions Read Safety Rules and Instructions Carefully Save this manual for Future Reference FPC Corporation 355 Hollow Hill Drive Wauconda IL 60084 Phone 847 487 4583 Fax 847 487 0174 website www surebonder com e mail sales surebonder com 1211 IMPORTANT SAFETY WARNINGS THE SAFETY WARNINGS BELOW CANNOT COVER ALL POSSIBLE SITUATIONS THAT MAY OCCUR THESE BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO PROTECT AGAINST PERSONAL INJURY TO THE OPERATOR OR OTHER PERSONNEL IN THE AREA AS WELL AS DAMAGE TO TH
3. Adjustable exhaust Rubber hand grip for comfort Firing Safety mechanism Easy drop in staple loading OPERATION The Surebonder 9630 Pneumatic Stapler is designed to use 1 4 crown heavy duty wire staples in 5 8 3 4 7 8 1 1 1 8 1 1 4 1 1 2 and 1 9 16 leg lengths For best results use Surebonder Heavy Duty Staples AIR SUPPLY This stapler is designed to operate on clean dry regulated compressed air between 60 and 100 psi It is preferable to include an air filter pressure regulator and automatic oiler within 15 feet of the tool if possible An air filter is needed to remove contaminates and moisture that are contained in compressed air filtering will significantly prolong the life of the tool If an automatic oiler is not installed place 5 to 6 drops of oil into the tool s air inlet at the beginning of each work day The staple gun comes factory equipped with a male quick connector The staple gun must always be connected to the air supply with a coupling that removes all pressure when it is disconnected NOTE all components used with this staple gun air hose connectors regulators filters etc must be rated at 150 psi OR 150 of the maximum compressor potential whichever is higher Do not connect this staple gun to a system with maximum potential air pressure greater than 200 psi AIR CONNECTION SETUP Quick Connector Quick Coupler o Air Tool To compressor Lubricator Regulator Filter DO N
4. E EQUIPMENT READ AND UNDERSTAND THESE WARNINGS BEFORE USING EQUIPMENT Keep tool away from children and DO NOT allow children near work area Do not allow children or untrained personnel to handle this tool DO NOT operate this stapler while tired or under the influence of drugs alcohol or medication that makes you drowsy Never point the stapler at yourself or others always assume that the stapler is loaded and proceed with caution Wear safety glasses and ear protection The tool operator and all personnel in the work area must wear safety glasses that protect the front and side to avoid eye injury Ear plugs should be worn to avoid hearing damage If operator will be working in a situation where overhead work will be done i e on a ladder stairs or scaffolding a hard hat must be worn Never wear loose clothing or jewelry because it can get caught in the moving parts of this tool Make sure long hair is covered to avoid getting it caught in stapler Keep the tool pointed away from yourself and others at all times Keep hands and all body parts away from rear area of stapler near air hose to guard against injury Keep hands and feet away from firing head during use Keep proper balance and footing at all times do not over reach Never use oxygen bottled gas or any type of combustible fuel as a power source it can cause an explosion and serious injury Do not use near flammable liquids or gases the stapler spar
5. OT place finger on trigger when disconnecting air hose the stapler could fire when reconnected to the air supply Carry tool by the handle only not by the air hose Do not drive staples close to the edge of the workpiece It could split allowing a staple to fly or ricochet and causing personal injury Do not try to drive staples at too steep an angle Make sure stapler is held firmly during firing to minimize recoil Do not drive a staple into very hard material thin material or on top of an existing staple the staple could ricochet causing personal injury Never use the stapler if it is leaking air the Safety mechanism is not working stapler has missing or damaged parts or requires repair Make sure all screws and caps are securely tightened Inspect the stapler before each use to insure that the trigger safety mechanism and spring are operating properly Lock the stapler in a clean dry storage area between uses Only use parts staples and accessories supplied or recommended by FPC Corporation Unauthorized parts or fasteners can lead to malfunction and serious injury Only personnel trained by FPC Corporation the distributor or the employer shall repair the stapler Do not modify this tool without the written approval of FPC Corporation Manufacturer assumes no responsibility for consequential or indirect damages from the use of this product Save this manual and have it available for tool operators reference Specifi
6. cations Overall Dimensions 9 65 x 9 61 x 2 09 Operating Pressure 60 100 PSI do not exceed 120 PSI Magazine Capacity 100 Staples Air Inlet Size 3 8 NPT Weight of Tool 2 9 lbs Staple Specs 1 4 Crown 18 gauge Heavy Duty Staples 5 8 3 4 7 8 1 1 1 8 1 1 4 1 1 2 and 1 9 16 leg lengths Adjustable Exhaust 1 4 Male Quick Rubber Grip Release Connector Track Release Lever Trigger Contact Safety Staple magazine Mechanism Staple viewer 9630 Parts List
7. escription Includes Includes no na ESHAUST VALVE COLLAR CYLINDER CAF 3630 3 3 T 14 18 13 zz 23 af 5630 7 FIRING YALYE PISTON PISTON HEAD 3630 14 SCREW 8 WASHER O RING 2 5 GASKET 3630 18 no DRIVER BLADE FIM DRIVER BLADE COLLAR 9630 19 SCREW 6 30 5630 22 WASHER 5 1 1t MG 13 8724 MG 31 2 5 0 F D F O F O F O F 0 A 9630 23 CLYINDER no 3630 27 WASHER MG 26 3 5 STOPPER SPACER MG 22 027 no MOZZLE 5630 31 al MG 44 3 2 6 MG 32 25 UPPER REMOTE HOUSING 3630 33 33 PIM RETAINER 5 572 no REMOTE CORE 5630 36 3 38 40 FIM 2 5 6 8 MG 3 18 O F O F O F O F O F 0 A REMOTE HOUSING 3630 28 FIN FERTAINER 3 12 5 MG 2 612 no RELEASING BLADE TRIGGER 3630 40 MG 12 571 8 MG 141 2 MG 23 3 3630 42 42 48 AO 5z 55 59 61 CATCH GUIDE PLAE 5630 44 SPRING FIM 3724 no PBLEASE CATCH E TAIL COVER 9630 50 MG 26 69 2 95 3630 52 no CLICK LEVER 5630 55 RELESE CATCH COVER RELESE CATCH A DRIVER GUIDE SPACER 9630 59 3630 60 _ rm re mn Be E a a 2 S o no 9630 61 SPACER wh a T l dh 5630 62 Be Bo B Tl SCREW Sz no UPPER MAG 3630 63 SCREW 4 12 MAGAZINE SUPPORT PUSHER 3630 64
8. ks during operation and could cause an explosion and serious injury Use an air hose that will withstand at least 150 psi OR 150 of the maximum pressure of the compressor Never connect this tool to compressed air if the pressure could exceed 200 psi as the stapler _ could burst Use only clean dry regulated compressed air with pressure not exceeding 120 psi Disconnect stapler from air supply before loading staples to prevent a staple being fired during connection to air hose Do not use a non relieving coupler with this stapler if used the stapler could remain charged with air after disconnecting and would still be able to drive a staple even after being disconnected The stapler and air hose must have a coupling so that all pressure is removed from the stapler when the coupling is disconnected Do not depress the trigger or safety mechanism while loading staples accidental firing of a staple can occur Keep your fingers away from the trigger when not firing staples Always keep the stapler pointed downward during loading Do not use an air hose that is too long tool operator can trip over it Make sure all connections are tight Disconnect air hose from stapler before performing maintenance when clearing a jam when tool is not in use when moving it to another location when handing stapler to another person WARNINGS continued next page Part Kits FASTENER Kit 9630 420 Seal Kit 9630 400 D
9. y more pressure to slide the magazine closed Using the Stapler This stapler is equipped with a contact safety mechanism the trigger will not operate unless the contact mechanism is firmly depressed against the surface to be stapled Grip the body of the stapler firmly make sure that the contact mechanism Is placed securely against work surface and pull the trigger to drive a staple Remove finger from the trigger To drive another staple move the stapler to next area on work surface to be stapled and repeat these steps After Stapling Disconnect the air hose from the stapler Remove all staples from the staple magazine of the stapler Place several drops of oil included in case into the air inlet Shut off air compressor and drain any moisture from the compressor tank Drain the air line filter clean the filter element then blow air in opposite direction to remove any dirt debris Keep lubricator filled with oil included in case Clearing Staple Jams Disconnect the air hose from the stapler Carefully remove staple strip from staple magazine Remove any remaining loose staples from inside the staple magazine using pliers to grasp the staples if necessary Once jammed staples have been removed reload stapler APPLICATIONS Including but not limited to Furniture Underlayment Paneling Molding trim Soffits and general staple use FEATURES View window for staples
Download Pdf Manuals
Related Search