Professional Woodworker 8637 Use and Care Manual
Contents
1. blade in place and loosen the hex bolt by turning clockwise using the socket wrench Then remove the hex bolt outer flange and saw blade Socket wrench WZ a Gi if ani Hee Shaft Locking Arm Install the new saw blade Check that the teeth point in the direction of the arrow see the protective cover ATON Sawblade Protective cover Install the outer flange and the hex bolt then press down the shaft locking arm and tighten the hex bolt firmly by turning it counterclockwise using the socket wrench Then secure the central cover back in place by adjusting the hex bolt When removing the saw blade lift up the movable hood and central cover loosen the hex bolt with the socket wrench remove the hex bolt outer flange and saw blade inner flange Outer flange Install shaft Hex bolt SLAS ANN reg les ESS Sas LL BSS BSD Saw blade feedback natitools com 1 800 348 5004 MOVEABLE HOOD When sawing the movable hood will be lifted up by the work piece The movable hood will automatically be reset to its Original position when the handle is raised after you finish cutting Never abandon or remove the movable hood SAWDUST COLLECTOR You can operate this machine more conveniently with the sawdust collector Connect the adapter of the collector to the nozzle of the protective cover and then fix the collector inlet to the adapter of the collecto2. the work piece Once you have finished cutting turn the switch off and wait until the saw blade comes to a full stop then raise the handle completely SET A BEVELED JOINT ANGLE Loosen the hand shank by turning feedback natitools com 1 800 348 5004 it counterclockwise Press down the spring pin so that the rotary table is free to turn When the desired angle on the base scale matches up with the arrow marked on the rotary table turn the hand shank clockwise to tighten it Indicator Hand Shank Miter Square SET A BEVELING ANGLE Only when the auxiliary stopper is fixed on the left side as shown can the saw blade be beveled to a 45 degree angle To adjust a beveling angle loosen the fixed handle then incline the saw blade to the left until the indicator reaches the desired angle on the miter square Tighten the fixed handle firmly Fixed Handie Indicator nals ee Fixed Handie Miter Square SS SECURE THE WORK PIECE The vertical vise can be installed in hole of guide bar or the work piece supporter component selective purchasing Install the vise rod in the hole of the guide bar or work piece supporter component then tighten the bolt You should adjust the position of the vise arm according to the thickness and shape of the work piece and tighten the vise arm with the bolt Lean the work piece against the guide bar and the rotary table and place
3. Please carefully read and save these instructions before attempting to assemble maintain install or operate this product Observe all safety information to protect yourself and others Failure to observe the instructions may result in property damage and or personal injury Please keep instructions for future reference important Operating Instructions North a 12 INCH MITER SAW WITH LASER y Model 8637 IMOWSTRITNIS CALIFORNIA PROPOSITION 65 WARNING You can create dust when you cut sand drill or grind materials such as wood paint metal concrete cement or other masonry This dust often contains chemicals known to cause cancer birth defects or other reproductive harm Wear protective gear WARNING This product or its power cord may contain chemicals including lead known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling CAUTION FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL COMPLETELY AND CAREFULLY BEFORE OPERATING THIS MITER SAW WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electrical shock fire and or serious personal injury SPECIFICATIONS Motor 120V 15A Speed 4100 RPM Blade Diameter 12 inch Table Tilting Range L 45 R 45 Saw Body Tilting Range 0 45 SAVE THESE INSTRUCTIONS SAFETY INFORMATION Always wear proper safety protecti
4. he carbon brushes regularly When the brushes wear down to the limit mark they should be replaced right away Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Brush holder cap Use a screwdriver to remove the brush holder caps Take out the worn carbon brushes insert the new ones and secure the brush holder caps feedback natitools com 1 800 348 5004 Limited Manufacturer Warranty North American Tool Industries NATI makes every effort to ensure that this product meets high quality and durability standards NATI warrants to the original retail consumer a 1 year limited warranty from the date the product was purchased at retail and each product is free from defects in materials Warranty does not apply to defects due directly or indirectly to misuse abuse negligence or accidents repairs or alterations or a lack of maintenance NATI shall in no event be liable for death injuries to persons or property or for incidental special or consequential damages arising from the use of our products To receive service under warranty the original manufacturer part must be returned for examination by an authorized service center Shipping and handling charges may apply If a defect is found NATI will either repair or replace the product at its discretion feedback natitools com 6 1 800 348 5004 C Amarican _ 12 Inch Miter Saw with Lase
5. lat Washer M10 Cord Guard Rocker Needle Spring Rivet D2 5x18 Safety Assembly EN Cushion Plate Nylon Lock Bolt Clip D6 ET Lever of Bolt M8x35 89 Spring of the Rocker KEH Fence feedback natitools com 8 Dust Bag Pipe 1 800 348 5004 Lock Handle Parts List Call 1 800 348 5004 for assistance or replacement parts Please provide the following information Address any correspondence to Model number Part description and number as shown in parts list apa sekung um Serial number if any Huntington IN 46750 C Be Hex Bolt M6x20 Bearing 017x040x12 No 7 Battery Lock Screw M5x20 Cover of Bearing Laser Switch Hex Bolt M6x40 Screw M5x16 Screw ST4 2x10 SafetyGuard SafetyGuard gg Inner Flange Battery Fixed Plate of Movable Saw Blade Touching Part 2 E Guard l ScrewM6 M6 EH Screw of Shaft Bearing 10x 30x9 ei KA TIRT Te 99 Hex Bolt M5x10 C Type Flat Key Stator Assembly Spring 17 Bearing 15x 35x11 Kerf Board Zine Holder of Laser Movable Safety Guard Lock Nut Assembly Screw M4x16 6 Spring Washer M6 Wave Type Washer Positioning Plate Wind Resisting Column Pipe Slide Slot of Gear Gear Holder l l Slide Bar Ring Spring Washer D5 113 Rotor Clip Spanner feedback homier com 1 800 348 5004
6. natitools com 1 8808637 07 10 Give the saw a test run before cutting If the tool vibrates excessively or makes unusual noises stop operating the saw immediately and correct the problem Before lowering the blade to the work piece make sure it has reached maximum speed If anything appears to be wrong turn the tool OFF and stop working immediately Before performing any maintenance or adjustments make sure that the power is OFF and the saw blade has stopped completely Always remain alert watch what you are doing and use common sense when operating a power tool Do not use when tired or under the influence of drugs alcohol or medication Use only recommended accessories specific for the power tool Do not abuse the cord Never use the cord to carry the tool or pull the plug from an outlet Keep the cord away from heat oil sharp edges or moving parts Replace damaged cords immediately KEEP THESE INSTRUCTIONS FOR FURTHER REFERENCE CHANGING THE SAW BLADE Unplug the saw before performing any maintenance or changing the blade To remove the blade loosen the bolt in the central cover by turning it counterclockwise using the socket wrench provided Then raise the central cover and move it down from the original position Centrai cover Z Socket wrench When removing the saw blade first raise the handle to the highest position press down the shaft locking arm to lock the saw
7. on safety goggles should be worn at all times Dust mask non skid safety shoes hardhat or hearing protection should also be worn at appropriate times Do not operate in the presence of explosive materials such as flammable liquids gases or dust Maintain tools with care Keep blades sharp and clean If the blade is broken or deformed replace immediately Be careful not to damage the output spindle flanges especially the fitting surfaces and the bolt Check whether the saw blade is in good condition Use the special flanges provided for this tool only Secure the saw to a workbench or table before use to prevent unexpected saw movement Make sure that the work area is clear of debris before starting Before cutting make sure that the work piece is free of nails screws or other foreign objects Make sure that the armature shaft is free from lock by the shaft locking arm before you turn it on Make sure that the saw blade will not touch the rotary table when the saw blade is in its lowest position Never operate this tool with one hand Secure work piece with the vise never secure the work piece by hand Hold the handle firmly Never let your hands get close to the cutting line do not touch the saw blade For warranty purchases please keep your dated proof of purchase File or attach to the manual for safekeeping For Customer Service please call 1 800 358 5004 or email feedback
8. r INDUSTRIES predp nana Parts List 08637 bbt Idd dodo rt M ge LAN La i Aa b r P P LEE BA ballad uf La bd m G g g d 8a88 a For Customer Service please call 1 800 358 5004 or email feedback natitools com 7 8808637 07 10 Parts List Call 1 800 348 5004 for assistance or replacement parts Please provide the following information Address any correspondence to Model number Part description and number as shown in parts list apa sekung Serial number if any Huntington IN 46750 e oeren ary e oeeo ary vo Pasean ary Indexing Handle Washer D8 Hex Bolt M5x50 2 Indexing Spanner pt EA Hex Bolt M10x85 Aa 62 Hex Bolt M10x15 EE amp i Indexing Pin a al Spring Washer D8 63 Flat Washer D5 a Pin D3x20 1 34 Hex Bolt msx25 64 Motor Enclosure 5 Indexing Spring KH 35 Plastic Stop Fence H BE L Head Screw i i i M 6 Indexing Cover Plate Braking Ring Sensor 7 Sunk Head Screw Hex Bolt M6 M5x12 Cord Plate E Lock Screw M6x25 KA Hex Bolt M8x55 68 Carbon Brush po Nylon Lock Nut M8 i 69 Screw ST4 2x13C Lock Screw M6x10 i Holder of Carbon Brush Worktable Switch Actuating Spanner Big Rubber Ring i Cover of Holder of Brush Long Slide Bar Switch Handle 47 Bracket of Slide Bar 4 Felt Ring Support Screw ST3 5x9C Rocker Graduation F
9. r When the sawdust collector is half full take the collector off from the protective cover open the collector door at the bottom and clean out the sawdust Sawdust nozzle Sawdust collector OPERATING THE SWITCH To prevent accidental starting this tool is equipped with a protective switch To start the tool you should first press the protective switch and press down the trigger switch When you release the trigger switch the tool is switched off Protective button Trigger switch OPERATION 1 Press Cut cut small work piece The work piece size within the scope 4in H x 13in W can be cut in the following way Push the carriage to the end towards the cross bar tighten the knob to fix the carriage Use the vise to secure the work piece Switch the machine on wait until the saw blade reaches its maximum speed and then press the handle downwards slowly After you have finished cutting turn the switch off and wait until the saw blade comes to a complete stop before raising the handle completely 2 Slip cut cut wide work pieces The work piece size within the scope 4in H x 8 1 2in W can be cut in the following way Release the knob in order to slip the carriage freely completely pull the carriage towards the operator Switch the machine on and wait until the saw blade reaches its maximum speed then press the handle and push it to the cross bar in order to cut
10. the work piece on the desired cutting position then tighten the clamp bolt to secure the work piece Rotary Fabie KEEP THE MAXIMUM CUTTING CAPACITY Before any adjusting unplug the saw from the power source This machine has been adjusted by the manufacturer to keep the maximum cutting capacity using an 8 inch saw blade When the diameter of the saw blade becomes smaller because of grinding please adjust the machine as follows Lower the carriage to the cross bar completely put down the handle to the lowest position Make sure the blade is properly aligned Unplug _ the cord and use your hand to spin _ the blade The blade should spin _ smoothly without making contact with any other part of the saw If there is contact realign the blade before using the saw With the socket wrench turn the adjustable bolt to make the edge of the saw blade fit into place ensuring that it falls slightly below the rotary table Make sure that the saw is unplugged then press the handle to the lowest position to ensure that the blade does not touch the table below Then if necessary adjust the blade Adjusting Bait _ Note Before installing the new saw blade make sure it does not contact any part of the table below _ MAXIMUM CUTTING CAPACITY 9 aie a aroma scenes feedback natitools com 4 1 800 348 5004 REPLACING THE CARBON BRUSHES Limit mark Check and remove t
Download Pdf Manuals
Related Search