Kawasaki 840889 Use and Care Manual
Contents
1. 1 4 in hex shafts The Cordless Screwdriver does not have the speed necessary to be used as a drill BATTERY BR Do not incinerate the internal battery even if it is severely RBRC damaged or is completely worn out The battery can explode AM Do not disassemble the internal battery or remove any com y y ponent projecting from the battery terminals Fire or injury 822 may result Prior to disposal protect exposed terminals with heavy insulating tape to prevent shorting The internal battery is Lithium lon Li lon and is considered to be a toxic mate rial by the Environmental Protection Agency Before disposing of damaged or worn out Li lon battery check with your State Environmental Protection Agency to find out about special restrictions on the disposal of the battery take them to your local recycling center for proper disposal or call 1 800 822 8837 10 The internal battery is not fully charged Before first use the battery requires 8 10 hours charge time to be fully charged Subsequent recharging needs 3 5 hours for the battery to be fully charged Always recharge internal battery when tool performance begins to diminish Severe heat is most destructive to a battery the more heat generated the faster the battery loses power A battery that gets too hot can have a shortened life Never over discharge a battery by using the tool even after tool performance has decreased Do not attempt to discharge a tool s battery2. SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges 21 22
3. 1 8 SAFETY RULES FOR SCREWDRIVERS 005 7 8 SYMBOLS sec sRd a EA R aan args ok 8 SECTION THREE FUNCTIONAL DESCRIPTION 2 0 cece eee eee 9 10 SCREWDRIVER BIT INSERTION 0 eee eee 10 BATTERY sonia aaa od 10 12 CHARGER toa 11 CHARGING THE SCREWDRIVER BATTERY sssusuuse 12 ASSEMBLY ccr dw doe thee ue EREMO E Edu 13 INSERTING THE SCREWDRIVER BITS INTO COLLET 13 OPERATING THE CORDLESS SCREWDRIVER 00 13 15 TRIGGER SWITCH rb RR 4a tes ab 13 FORWARD REVERSE AND TRIGGER LOCK BUTTON 14 TORQUE SETTINGS 243i sep RR pn edes 14 AUTOMATIC SPINDLE LOCK sssssssssnnnmm 15 ADJUSTABLE HANDLE 00 cee eee eee eee 15 WORKLIGHT cuco dba Shion tka Se awake tee 15 SECTION FOUR MAINTENANCE AND CLEANING 0 c eee eee eee eee 15 16 ACCESSORIES aiii das dead Ria 16 SPECIFICATIONS 4 nt ure bres 17 PROTECTING THE ENVIRONMENT ssseesseeennn I 17 OTHER CONSUMER DO IT YOURSELF DIY TOOLS 17 SECTION FIVE 3 YEAR LIMITED WARRANTY 0 0 eee eee Re 18 21 CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help or advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INT
4. BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH 20 DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE
5. DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi Purpose Tools Wide Range of Accessories and more 17 3 YEAR LIMITED HOME USE WARRANTY Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and work manship for a period of three years from original date of purchase except that such warranty with regard to the battery shall be for a period of two years from the orig inal date of purchase unless the tool is used for commercial or rental purposes SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS This Kawasaki portable power tool is offered as a home use tool and carries a HOME USE WARRANTY This tool is made for home use in the execution of projects and repairs in and around the home Use of the tool for COMMERCIAL PURPOSES OR ON A JOBSITE is not covered under this warranty The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession
6. custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified altered or used for any commercial purpose or on a jobsite This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 800 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purch
7. grip or an in line grip To change positions depress handle release button swivel handle to the desired position WORKLIGHT The Cordless Screwdriver comes with a LED Worklight mounted just below the torque setting control ring This light illuminates the fastener being removed or installed by the screwdriver To turn on the Worklight push the black button mounted on the side of cordless screwdriver When the project is finished push the button to turn off the light MAINTENANCE AND CLEANING 4 WARNING No user serviceable parts inside Preventive mainte nance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard TOOL LUBRICATION Your screwdriver has been properly lubricated and is ready for use 15 A WARNING To avoid accidents always disconnect the tool and or charger from the power supply before cleaning The tool may be cleaned most effectively with compressed dry air Always wear safety goggles when cleaning tools with compressed air Ventilation openings switch and switch levers must be kept clean and free of foreign matter Do not attempt to clean by inserting pointed objects through opening 4 CAUTION Certain cleaning agents and solvents damage plastic parts Some of these are gasoline carbon tetrachloride chlorinated cleaning solvents ammonia and household detergents that contain ammonia Use only accessories
8. of battery may create a risk of fire when used with another battery Use battery operated tool only with specifically designated battery pack Use of any other batteries may create risk of fire PERSONAL SAFETY A WARNING Stay alert watch what you are doing and use common sense when operat ing a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Keep your hair cloth ing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Prevent accidental starting Ensure switch is in the OFF position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energizing power tools that have the switch ON invites accidents Remove adjusting keys or wrenches before turning the tool ON A wrench or a key that is left attached to a rotating part of the tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Use personal protective equipment Always wear eye protection Protective equipment such as dusk mask non skid safety shoes hard hat or hearing protec tion used for appropriate conditions
9. or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disclaimers 19 EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS
10. that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gauge is large enough to carry the amount of current necessary for your power tool If not your tool may experience a loss of power excessive voltage drop or overheating The smaller the gauge number the heavier the cord see table on below RECOMMENDED SIZES OF EXTENSION CORDS FOR 120 VOLT AC 60 HZ TOOLS CURRENT RATING IN AMPS CONDUCTOR SIZE IN A W G MORE THAN NOT MORE THAN 25 FT 50 FT 100 FT 150 FT 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 NOT RECOMMENDED 16 SPECIFICATIONS SPECIFICATIONS Voltage 4V No Load Speed 200 RPM Torque Settings 8 1 Drill Locking Collet 1 4 In 6 35mm Adapter Charger 120V N 60 Hz Charging Time Approx 3 5 Hours Battery Type Lithium Ion PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times At the end of their useful life recy cle batteries with due care for our environment Lithium lon Li lon batteries are recyclable Take them to your local recycling center or call 1 800 822 8837 Collected batteries will be recycled or disposed of properly OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make
11. to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation BATTERY TOOL USE AND CARE 44 CAUTION Ensure the switch is in the off position before inserting battery pack Inserting battery pack into power tools that have the switch on invites accidents Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery termi nals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes addi tionally seek medical help Liquid ejected from the battery may cause irrita tion or burns 4 CAUTION Tool service must be performed only by qualified repair personnel Service or maintenance by unqualified personnel may result
12. to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance
13. E MODELE DATE DE L ACHAT ET ADRESSE DU MAGASIN UN REPR SENTANT D ALLTRAD PEUT R SOUDRE VOTRE PROBLEME PAR T L PHONE POUR TOUT COMMENTAIRE OU SUGGESTION N H SITEZ PAS NOU APPELER OU NOUS CONTACTER PAR COURRIEL L ADRESSE INFOGALLTRADETOOLS COM VOS COMMENTAIRES NOU SONT EXTR MEMENT PR CIEUX SI TIENE DUDAS 0 SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1 800 590 3723 ANTES DE LLAMAR TENGA A MANO LA SIGUIENTE INFORMACI N No DE MODELO FECHA DE COMPRA Y DIRECCI N DE LA TIENDA UN REPRESENTANTE DE ALLTRADE PUEDE RESOLVER SU PROBLEMA POR TEL FONO SI DESEA HACER ALGUNA SUGERENCIA O COMENTARIO LL MENOS O ENV ENOS UN MENSAJE DE CORREO ELECTR NICO A INFO ALLTRADETOOLS COM SUS COMENTARIOS SON FUNDAMENTALES PARA NOSOTROS L S E S S TABLE OF CONTENTS CONGRATULATIONS occ 2 INTENDED USE eese nee 2 SECTION ONE GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 2 7 RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS 00 eee eee eee 3 WORK AREA o 1 rot Gs Sto ee Ke ee RE Sh ES ewe 4 ELECTRICAL SAFETY 0 cece eee eee 4 PERSONAL SAFETY 0 e cece eee teens 5 TOOLUSEANDCARE sssssse eee 5 6 BATTERY TOOL USE AND CARE eee eee 6 SERVICE 51s e spese M A pate Mew 4 7 SECTION TWO SPECIFIC SAFETY RULES AND OR SYMBOLS
14. ENDED USE This tool is intended for consumer use only Your charger and or adapter has been designed for charging batteries of the type approved and supplied with this tool GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS 4 WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A DANGER WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury 2 A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation
15. FOR CUSTOMER SERVICE POUR LE SERVICE APR S VENTE 0U DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Imprim dans la Chine Impreso en China OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO KAWASAKI EST UNE MARQUE DE COMMERCE DE KAWASAKI MOTORS CORP U S A QUI NE FABRIQUE PAS ET NE DISTRIBUE PAS CE PRODUIT THIS PRODUCT LES QUESTIONS DES CONSOM MATEURS DOIVENT ETRE ADRESSEES A KAWASAKI ES UNA MARCA REGISTRADA CON LICENCIA DE KAWASAKI MOTORS CORP E U A QUE NO FABRICA NI DISTRIBUYE ESTE PRODUCTO LAS CONSULTAS DE LOS CONSUMIDORES DEBEN DIRIGIRSE A COPYRIGHT 2010 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 691512 4V Battery Operated Screwdriver Visseuse sur Batterie de 4 V Destornillador Operado con Bater a de 4 V Rev 10 29 10 COMPONENT i COMPOSANT W S i COMPONENTE 691512 4V BATTERY OPERATED SCREWDRIVER INSTRUCTION MANUAL MANUEL D UTILISATION DE LA VISSEUSE SUR BATTERIE DE 4 V MANUAL DE INSTRUCCIONES PARA EL DESTORNILLADOR A BATERIA DE4 V THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THIS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESUL
16. RNING Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet Always turn the switch OFF before changing bits INSTALLING SCREWDRIVER BITS INTO COLLET A WARNING Before inserting a screwdriver bit or other accessory make sure the forward reverse and trigger lock lever is in the center OFF position to prevent accidental starts that may result in injury When removing the hit from the tool avoid contact with skin and use proper protective gloves when grasping the bit or accessory Accessories may be hot after prolonged use 1 Pull the quick release collet sleeve back towards the screwdriver 2 Insert the shank of the bit or other accessory fully into the collet 3 Let the sleeve slide back to lock in the bit OPERATING THE CORDLESS SCREWDRIVER 4 WARNING Never tape the trigger switch down to provide continu ous high speed The tool may fail under such conditions causing fire or personal injury TRIGGER SWITCH THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH To start the Cordless Screwdriver press the trigger switch Release the pressure and the Cordless Screwdriver will stop 13 FORWARD REVERSE AND TRIGGER LOCK BUTTON NOTE Be sure the trigger is released when changing the position of the lever Always store the tool in the LOCKED OFF position Always check the direction of the Cordless Screwdriver s rotation b
17. T IN SERIOUS PERSONAL INJURY AND OR PROPERTY DAMAGE CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA S CURIT LE FONCTIONNEMENT ET LE REMISAGE DE CE PRODUIT LIRE TUDIER ET VEILLER BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS ET AUTOCOLLANTS APPOS S SUR LE PRODUIT AVANT DE L UTILISER NE PAS RESPECTER CES INSTRUCTIONS POURRAIT ENTRA NER DES BLESSURES ET OU DES DOMMAGES MAT RIELS ESTE MANUAL CONTIENE INFORMACI N IMPORTANTE SOBRE LA SEGURIDAD OPERACI N MANTENIMIENTO Y ALMACE NAMIENTO DE ESTE PRODUCTO ANTES DE USARLO LEA Y COMPRENDA TODAS LAS PRECAUCIONES ADVERTENCIAS INSTRUCCIONES Y ETIQUETAS DEL PRODUCTO DE LO CONTRARIO PODR A SUFRIR LESIONES GRAVES O CAUSAR DA OS MATERIALES IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GIVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US POUR TOUTE QUESTION OU EN CAS DE PROBLEME AVEC LE PRODUIT ALLTRADE NE PAS LE RETOURNER AU MAGASIN OU A T ACHET APPELER LE SERVICE APRES VENTEAU 1 800 590 3723 AVANT D APPELER VEILLER SE PROCURER LE INFORMATIONS SUIVANTES No D
18. The charging unit uses common prongs both prongs are the same requiring no special polarized or grounded AC receptacles Both the charger unit and the plug are molded that cannot be opened for repair To charge the battery on the cordless screwdriver use the following steps BATTERY CHARGE STATUS BUTTON 1 Plug the charger into a common AC receptacle 120V AC 60 Hz 2 Insert the charger plug into the receptacle on the handle 3 Verify that the charging indicator light is on The red indicator light turns on while the battery is being charged If the red light fails to come on and the Battery Status Indicator lights show the battery needs recharging check to make sure the AC receptacle is turned on power present If the charging indi cator light still does not turn on the problem could be the AC charging unit Contact Alltrade Customer Service at 1 800 590 3723 toll free to purchase a new charger 4 Observe the Battery Status Indicator Lights located on the top of the Cordless Screwdriver Directly behind the status indicator lights is a battery test button Press this button to illuminate the status indicator lights There is a green yellow and red indicator light If the battery is charged all three lights will come on When the battery is low and needs recharging only the yellow and red light will illuminate When the battery is too low to operate the screwdriver only the red light will illuminate 12 ASSEMBLY 4 WA
19. ase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or 18 reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations
20. by continuing to pull on the tool trigger When tool performance begins to diminish stop the tool and recharge the battery for optimal performance Charge internal battery at ambient temperatures between 50 F 104 F Store tool and battery in locations where temperatures will not exceed 120 F This is important to prevent serious damage to the battery cells LA CHARGER d WARNING Before using the AC battery charger unit please read carefully all instructions and cautionary markings on charger battery and product using battery NOTE When the battery is fully charged the charging process stops and the charging indicator light will automatically turn OFF Use only the charger which accompanied your product or direct replacement as listed in this manual Do not substitute any other charger Use only Alltrade approved chargers with your product Do not disassemble charger Do not use charger if it has been damaged left outdoors in the rain snow wet or damp environments or immersed in liquid When the battery requires recharging a 3 5 hour charge allows the tool to oper ate at full power A charging indicator light on the charger will illuminate to show that charging is taking place 11 CHARGING THE SCREWDRIVER BATTERY The Cordless Screwdriver has a rechargeable state of the art lithium battery The battery is charged with a charger that is plugged into the screwdriver on the front side of the handle
21. efore use TO SELECT THE DIRECTIONS OF ROTATION To select forward Cordless Screwdriver rotation press the trigger lock from right to left flat against the Cordless Screwdriver body To select reverse press the trigger lock lever in the opposite direction b FORWARD The center position locks the tool TORQUE SETTINGS NOTE To prevent damaging the tool or driving screw too deep into work piece release the trigger when you feel the clutch slip THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE For light duty work use lower settings For heavy duty work use higher settings PROPER SETTING FOR DRIVING SCREWS 1 Set the ring on the lowest setting to begin Po Try tightening the first screw If the screwdriver drives smoothly proceed with the next screw 3 If the screwdriver s clutch slips EE increase the torque setting CONTROL RING and try again until the screwdriver drives the screw without incident 14 AUTOMATIC SPINDLE LOCK The Cordless Screwdriver is equipped with an automatic locking system This feature will lock the bit holder in one position when the trigger switch is released This will allow you to tighten or loosen a nut or screw by rotating the tool by hand with the switch off This is convenient when higher turning torque is required ADJUSTABLE HANDLE The Cordless Screwdriver features an adjustable handle that can be positioned as a pistol
22. in a risk of injury When servicing a tool use only identical replacement parts Follow instruc tions in the Maintenance section of this manual Use of unauthorized parts or 4 CAUTION USE ONLY THE AC CHARGER THAT CAME WITH THE CORDLESS SCREWDRIV ER Should the AC charger fail to charge the battery in the screwdriver contact Alltrade Customer Service at 1 800 590 3723 toll free to purchase a new one DO NOT ATTEMPT TO CHARGE THE CORDLESS SCREWDRIVER IF THE POWER CORD IS BROKEN OR FRAYED Always store the charger in a clean dry location until it is needed failure to follow Maintenance Instructions may create a risk of shock or injury SPECIFIC SAFETY RULES AND OR SYMBOLS 4 WARNING Hold tool by insulated gripping surfaces when perform ing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator SAFETY RULES FOR SCREWDRIVERS 4 CAUTION MAKE SURE APPROVED EYE PROTECTION IS BEING WORN and properly adjusted and secured at all times the cordless screwdriver is being used There is a possibility that small pieces of metal could shear off from over tightened screws while using the tool KEEP CHILDREN at a safe distance while using the cordless screwdriver Distractions can cause inadvertent misuse resulting in possible injury to children or to the user USE ONLY SCREWDRIVER TIPS that are designed for use with
23. inutes Time S Seconds Time b Diameter Size of Drill Bits Grinding Wheels etc n No load speed No load Rotational Speed Strokes etc per Minute min Revolutions per Minute Revolutions Surface Speed Strokes etc per Minute 1 2 3 Ring Selector Settings Speed Torque or Position Settings 8 FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS 1 1 4 in Collet 8 Forward Reversing and Trigger 2 Collet Quick Release Sleeve Lock Button 3 8 1 Adjustable Torque Settings 9 LED Light Control Ring 10 LED Light Button 4 Battery Status Indicator Lights LEDs 11 Trigger Green Fully Charged 12 Pin Receptacle for AC Charger Yellow Low Battery Charge 13 Battery Charging Indicator Light Red LED not shown 14 1 4 in Screwdriver Bits 15 Charger Plug 16 120V Adapter Charger Red Warning Recharge Battery 5 Battery Charge Status Test Button 6 Handle Release Button 7 Comfort Rubber Grip COMPONENT MODEL NUMBER 120V ADAPTER CHARGER 691513 SCREWDRIVER BIT INSERTION The Cordless Screwdriver is equipped with a quick change collet that ONLY accepts 1 4 in hex shaft screwdriver bits Select the screwdriver tip best suited for the job Place the tip in the fastener and ensure it fits snug Tips that are too large or too small can damage the fastener by stripping out its head The Cordless Screwdriver should only be used as a screwdriver DO NOT attempt to use the tool as a drill using drill bits with
24. ors with impact drills Exposure to noise can cause hearing loss Use auxiliary handles if supplied with the tool Loss of control can cause personal injury ELECTRICAL SAFETY 4 WARNING Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radia tors ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock If operating a power tool in a damp location is unavoidable use a ground fault circuit interrupter GFCI protected supply Use of a GFCI reduces the risk of electric shock A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charger for the battery A charger that may be suitable for one type
25. this cordless screwdriver The tips should be INSERT TYPE screwdriver tips with a 1 4 in hex shaft If you are unsure of the types of screwdriver tips to use contact Alltrade Customer Service at 1 800 590 3723 toll free for authorized tip specifications ENSURE THE SCREWDRIVER TIP IS FIRMLY PLACED IN THE FASTENER TO BE INSTALLED OR REMOVED Hold the screwdriver firmly in place before acti vating the trigger switch Failure to hold the screwdriver firmly could cause the tip to strip the fastener head making it difficult to install or remove DO NOT PLUG THE AC CHARGER INTO AN OUTLET WHERE IT CAN BE EXPOSED TO WATER Do not lay the cordless screwdriver in or near water while it is plugged into the AC charger Failure to comply with this WARNING can result in severe electrical shock or severe burns to anyone who touches the charger or the cordless screwdriver SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL NAME EXPLANATION V Volts Voltage Potential A Amperes Current Hz Hertz Frequency Cycles per Second W Watt Power Kg Kilograms Weight NU Alternating Current Type of Current Direct Current Type of Current Alternating or Direct Current Type of Current Earthing Terminal Grounding Terminal n Class II Construction Denotes Double Insulation min M
26. which if not avoided may result in property damage NOTE NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood IMPORTANT SAFEGUARDS People with electronic devices such as pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm A WARNING Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Wear ear protect
27. will reduce personal injuries If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collec tion can reduce dust related hazards A CAUTION Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally 4 CAUTION Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many acci dents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier
Download Pdf Manuals
Related Search