Kwikset 911TNL TRL 11P SMT CP Instructions / Assembly
Contents
1. enabled wd e2 a eee If switch 3 is ON E Regulatory Compliance This product complies with standards established by the following regulatory bodies e Federal Communications Commission FCC e Industry Canada FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit diffe2. pack into interior Correctly orient latch A Correctly orient latch B S i g assembly yet D z 3 g Y F y Rounded edge k faces latch Ww A A2 Keep parallel to Angle edge of door ii i Ensure correct polarity For best results i use new non rechargeable Alkaline ie A Toig O batteries only Ww HG Tighten i 6 screws evenly S 2x 8 Install levers B c D A B C D Push excess cable back into the door as you install G L M A A D y b x Tighten the Tighten the pre installed pre installed Lever handle faces set screw Lever handle faces Q set screw Turnbutton may need to away from latch away from latch be turned to install G f j l Ensure tight cable connection 9 Install strike 10 Program the lock 11 Install battery cover and re key the lock Template A B A B c i ike P ing instructions e a ie lar ee SS ET Ga aes If your door requires drilling cut out the template and place it on the exterior side of the door Complete door side of this document drilling instructions are available on the SmartCode lever page of www kwikset com If small bolt of latch enters strike hole if reposition strike A COC Close door and test lever operation If latch is loose in the strike adjust strike tang If needed re key the lock to I work with your existing key Keep Q in a safe place as you See the supplied SmartKey will need it
3. 49492 03 Parts in the Box 1 Check dimensions A Adjust the backset of latch if needed Latch and Strike Exterior Assembly Interior Assembly Levers and screws A Hold the latch in front of the B If the latch holes are I a door hole with the latch face centered in the door hole no N d AN flush against the door edge adjustment is required mr See note Te o Proceed to step 3 below i 3 8 1 3 4 2 i 1 3 8 ne If the latch holes are NOT m OUCHPA ELECTE EVER 35 mm 44 mm centered adjust latch See a Latch Adjustment Installation Guide b f 2 3 8 60 mm nina If needed please contact 2 a fat equired Tools SS Kwikset to order a drive in 7 onm latch for your lock Latch Adjustment F T Use and programming Adj Additional Tools depending on application instructions are located on the only if needed reverse side of this document i aS Kwikset If you are installing this lever below an existing lock or you plan to install a lock above this lever 1 800 327 5625 make sure that the distance between holes is at least 6 1 2 165 mm www kwikset com E Install latch 4 Install keypad and mounting plate 5 Install spindle 6 Disassemble interior assembly and load battery pack A B A B C For doors with chiseled edge For doors without chiseled edge Gane none Aerian AA Q Do not install r A battery
4. Press Lock button once test Make sure switch 3 is on and then press the Program button once If you hear three beeps and see the keypad flash green three times the mastercode is enabled Note The lock will time out after five seconds If no button is pressed for five seconds the system will time out and you will need to restart the procedure Gi Battery Replacement If a deadbolt is installed above the lever remove interior assembly when battery replacement is required Bo Normal Operation Unlocking the Door Enter user code Tip You can press the Lock button before entering your user code to light up the keypad at night Locking the Door Press Lock button once If no user codes are programmed the Lock button will be disabled Incorrect Codes Codes Entered Lock Behavior Keypad flashes red three One incorrect code entered times with three beeps Three incorrect codes entered within one minute Keypad flashes red 15 times with 15 beeps If switch 3 is ON E Switches Status LED Colors and Keypad Warnings Switches LA 04 2 ON OFF Keypad o g B Status LED 12 90 4 123 4 Switch Function Color Lock Status Warning Reason Solution 1 Door lock status LED blinks every 6 seconds Green Unlocked Low battery Replace batteries Lock automatically re locks door 30 Keypad flashes 2 seconds after unlocking Disabled if ji Next Step no codes are ban ay red with fast Door j
5. ailable in multiple performance grades to suit the application In order to enhance security and reduce risk you should consult a qualified locksmith or other security professional 2014 Kwikset Corporation
6. ammed while Relock door If needed Amber Locked beeping sound attempting to lock reposition strike Re enter code for3 4 3 Audio seconds Re enter code after 60 i d p tleast second keypad lockout o user code rogram at least one 4 Not used Red Low battery programmed user code Adding User Codes Mastercode NOT enabled 1 Press the Program button the number of times that corresponds to the user code position being programmed Example If programming the third code press the button three times 2 Enter new USER code 3 Press Lock button once IF UNSUCCESSFUL Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt A TEST CODE While the door is open test the user code to make sure it unlocks the door Mastercode enabled 1 Press Program button once The keypad will flash green and you will hear three beeps 2 Enter MASTERCODE the code that was enabled in section b 3 Press Lock button once 4 Press the Program button the number of times that corresponds to the user code position being programmed Example If programming the third code press the button three times 5 Enter new USER code 6 Press Lock button once IF UNSUCCESSFUL Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt Make sure to enter a valid mastercode in step 2 A TEST CODE While the door is op
7. en test the user code to make sure it unlocks the door If no button is pressed for five seconds the system will time out and you will need to restart the procedure G Factory Reset A factory reset will delete all codes associated with the lock 1 Remove battery pack it 3 Press the Program button once more In 20 seconds when the LED flashes green and you hear one beep the lock has been reset 2 Press and HOLD the Program button while reinserting the battery pack Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red status LED If switch 3 is ON Deleting User Codes In order to delete a user code you must override the code by adding a different user code in the same position For example if you want to delete the third code add a different user code in position three A Test the old user code to make sure it is inactive If you cannot remember the user code position you may wish to perform a factory reset to delete all codes associated with the lock See section G Disabling and Deleting the Mastercode 1 Press and HOLD 2 Press Lock button once 3 Enter mastercode Program button until keypad flashes green about 5 seconds 4 Press Lock 5 Re enter 6 Press Lock IF UNSUCCESSFUL A TEST button once mastercode button once Make sure the Make sure switch 3 is on mastercode has been and then press the Program enabled before trying to but
8. rent from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help IMPORTANT Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment Industry Canada This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Exterior Keypad 56 34 78 a5 Lock button 12 90 Keyway SmartKey tool hole 1 Press and HOLD Program button until keypad flashes green about 5 seconds 4 Re enter mastercode 2 Enter new mastercode Interior cover removed Turnbutton Enabling and Adding a Mastercode Optional for Enhanced Security User codes can be programmed with or without a mastercode Using a mastercode is an optional added security measure It is not enabled by default A mastercode is used to add and delete user codes but it cannot unlock the door unless the same code is programmed as a user code though this is not recommended The mastercode must be 4 8 digits IF UNSUCCESSFUL Make sure the mastercode has not been programmed already Attempt this procedure again making sure to enter the same new mastercode in steps 2 and 4 Back panel Switches 3
9. to access the back Re key instructions for more l 1 panel for additional programming information l 2 3 8 60 mm 2 3 4 70 mm Backset 49492 03 ENGLISH Kwikset RTCODE SB User Guide Kwikset 1 800 327 5625 www kwikset com A SmartCode at a Glance Troubleshooting and FAQs are available online at www kwikset com D Programming Codes a Programming Information User Codes Requirements Installation instructions are located on the reverse side of this document Each user code must be a unique code between 4 and 8 digits A total of 8 user codes may be programmed How the Keypad Works Each button represents two numbers i e 1 and 2 for the first button You only need to push the button once to get either 1 or 2 For example If your code is 1 2 5 6 8 1 2 12 12 Programming Behavior Successful Programming 5 6 8 56 56 78 The keypad will flash green once and you will hear one beep Unsuccessful Programming The keypad will flash red three times and you will hear three beeps Successful Programming a Me x1 Timeout Unsuccessful Programming Hs Be A x3 If no button is pressed for five seconds the system will time out and you will need to restart the procedure Timeout Behavior Switch 3 ON Switch 3 OFF Mastercode red ae red Do enabled x6 Tet mh 6 x6 eie Mastercode red a 6 NOT
10. ton once If you don t disable it Attempt this procedure again making immediately hear three beeps or see the keypad sure to enter the same flash green three times the mastercode in steps 3 mastercode is disabled and 5 Note The lock will time out after five seconds If no button is pressed for five seconds the system will time out and you will need to restart the procedure p gt GO TIS gt Gu Important Safeguards Read all instructions in their entirety Familiarize yourself with all warning and caution statements Remind all family members of safety precautions Restrict access to your lock s back panel and routinely check your settings to ensure they have not been altered without your knowledge Protect your user codes and mastercode Dispose of used batteries according to local laws and regulations CAUTION Prevent unauthorized entry Since anyone with access to the back panel can change the user codes you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge The use of a mastercode can help protect your system s settings WARNING This Manufacturer advises that no lock can provide complete security by itself This lock may be defeated by forcible or technical means or evaded by entry elsewhere on the property No lock can substitute for caution awareness of your environment and common sense Builder s hardware is av
Download Pdf Manuals
Related Search