Ohio Steel 1084A Instructions / Assembly
Contents
1. 1 2 19 LR19A 4 Stiffener Bar This ramp must be only used for loading and unloading to and from a level and stable STDBH375750 8 Bolt 3 8 x1 Hex BB 84A BB 1 Hardware Bag surface REV G Use caution when using ramp in icy or wet conditions The ramp surface may become LIMITED ONE YEAR WARRANTY slippery If this product fails due to a defect in material or workmanship within one year from the date Do not use this loading ramp to load live animals of purchase Ohio Steel will at its option repair or replace it free of charge Proof of purchase Do not use loading ramps as a bridge scaffolding or any other use for which it is not ired for all ty claims intended or designed LQ UIEC Or al warranty ciaims If ramp is bowing while loading or unloading your equipment which indicates an overload This warranty does not cover condition remove the equipment immediately Repairs necessary because of operator abuse or negligence Do not attempt to load or unload any power equipment with its motor running Equipment used for commercial or rental purposes Failure to follow these warnings may result in property damage and or serious bodily injury Contact your nearest Ohio Steel partner to arrange for product repair or return this product to place of purchase for replacement Ohio Steel Industries o 2575 Ferris Road Columbus Ohio 43224 This warranty applies only while this product is in use in the U S A FOR MISSING PARTS Call 1 8002. 652 2321 When ordering repair parts always give the following information Monday Friday 8 a m 5 p m E S T PRODUCT NAME MODEL NUMBER PART NUMBER and PART DESCRIPTION PartNo Amt Description Ref No _ Part No 2 Ramp Top 10 STDWF375 1 SAFETY Be sure to read and follow all safety instructions and warnings Failure to follow these instructions may result in damage to the product and or serious personal injury Danger of serious personal injury exists Serious personal injury can occur when using a loading ramp Never attempt to ride any vehicle up or down the loading ramp Look for a wall or a depression to reduce the loading angle the lower the ramp angle the easier the loading of the vehicle will be Park the vehicle on flat firm grassy terrain Set the emergency brake and chock the tires of the loading vehicle to prevent any movement while loading and unloading the equipment Center loading ramp on the loading surface with support bars on top of the loading surface Make sure ramps are aligned at the proper distance apart so that the tires of the equipment being loaded are centered on the ramp To prevent kick back always attach cam buckle straps between the bumper of the truck and the center of loading ramp Pulling tight Roll or winch equipment up or down the ramp Before each use always check for any worn loose or damaged parts on the loading ramp If any damage is present DO NOT US
3. E THE RAMP Periodically check the fasteners to make sure they are still tight and in place Keep ramp surface clean by occasionally cleaning with water and any mild detergent Do not add to or try to modify the loading ramp in any way Any modifications will void any warranties as well as affect the structural integrity of the ramp itself OPERATION TOOLS SUGGESTED FOR We suggest that you drill 7 16 diameter ASSEMBLY holes through the support bars 3 into the tail gate or truck bed so that the pins 7 16 wrench and or socket can be inserted as a safety device in 9 16 wrench and or socket holding ramps in place To prevent kick Large blade screwdriver back of the loading ramp always attach bungee strap to bumper of truck and center of ramp stretching 5 to 6 Align individual ramps to correctly correspond to your ATV s track Always remove key turn fuel off and set parking brake after loading ATV Assembly Instructions Step 1 Stack one ramp top 1 on top of ramp bottom 2 Lay other ramp top upside down as shown Step 2 Place foot in center of upside down ramp top and apply enough pressure to create bow as shown Step 3 Add stiffener bar inside ramp top flange as shown with bolts 6 flat washer 7 and lock nuts Align hole in stiffener bar with hole in ramp top Do not tighten bolts until all bolts are in place Add stiffener bar to other side of ramp top Repeat steps 1 3 for other ramp top Note Stif
4. Repair Parts L OHIOS 22 INDUSTRIES ALUMINUM FOLDING LOADING RAMP Model 1084A e 750lbs capacity single e 1500lbs capacity double e Compact storage e One person loading WARNINGS Manufactured under U S Patent No 5 645 394 The loading ramp surfaces are sharp Always wear proper clothing and use care when handling the loading ramps Gloves are strongly recommended Read and understand all safety and operating instructions before using the loading ramp lat Washer 3 8 Never allow anyone unfamiliar with these instructions to use the loading ramps soll Read and understand all safety and operating instructions provided by the manufacturer 2_ Ramp Bottom 1 STDWSL375 8 Split Lock Washer 3 8 of the equipment the loading ramp will be used with 8 2 1 4 Support Bar 12 STDNH375 Hex Nut 3 8 Extreme caution should always be used while loading and unloading your equipment 4 Pin 14 303171 4 Support Bar Pad 16 ALR16 Cam Buckle Strap Do not exceed the rated capacity of the loading ramp eT T the manufacturer to find the maximum load capacity STDBH5001000 _4 Bolt 1 2 x1 Hex 17 STDBH375500 24 Bolt 3 8 x 3 4 Hex Never stand in the path of equipment being loaded and keep all bystanders and children Owners Manual Do not exceed the rated capacity of the loading surface i e tailgate If unknown contact STDWF500 8 Flat Washer 1 2 18 STDNC375 24 Lock Nut 3 8 away from loading ramps STDNC500 4 Lock Nut
5. fener bar is not symmetrical HOLE TO SHOW PLACEMENT OF STIFFENER BAR ONLY Ramp Top Assembly Step 4 Attach support bars 3 to ramp top 1 with bolts 9 flat washers 10 lock washers 11 and hex nuts 12 Tighten bolts at this time Step 5 Slide support bar pads 5 onto bars as shown Note Apply a little soapy water inside support bar pad this allows the pad to slide onto the bar easier Connecting the Two Ramp Halves Step 6 Invert ramp bottom 2 so that flanges face up Place ramp top 1 inside the ramp bottom so that the side holes of each are in line Step 7 Secure both side by inserting hex bolt 6 through flat washer 7 ramp bottom ramp top another flat washer 7 and tighten with lock nut 8 as shown NOTE DO NOT OVER TIGHTEN Ramp must be able to swivel open and shut
Download Pdf Manuals
Related Search