Home Decorators Collection 89420 Use and Care Manual
Contents
1. e e o Wine Shelf Insert Securing Block Fireplace Insert HOMEDEPOT COM HOMEDECORATORS 7 Please contact 1 800 986 3460 for further assistance Assembly 1 Preparing the back base panel Set the Back Base Panel D on a scratch free surface Screw the Small Bolts AA through the 3 Hole Plastic Connectors JJ 2 Assembling the base Align the Right Base C and the Left Base A with the Bottom Front Base B and the Back Base Panel D Screw the Flat Washers MM and Bolts LL through the pre drilled holes in the Bottom Front Base B and the Left Base A Screw the Small Bolts AA through the 3 Hole Plastic Connector JJ already connected to the Back Base Panel D Repeat to attach the Right Base C Assembly continued 3 Preparing the center side panel Set the Center Left Side Panel E on a flat surface Screw the Small Bolts AA through the 2 Hole Plastic Connectors Il to the Center Left Side Panel E Repeat for the Center Right Side Panel F 4 Attaching the decorative front panel Screw the Small Bolts AA through the 2 Hole Plastic Connectors Il to attach the Decorative Front Left Panel H to the Center Left Side Panel E Repeat to connect the Decorative Front Right Panel I to the Center Right Side Panel F 5 Preparing the2. cene eiit 19 Troubleshooting eene 20 Replacement Parts eeeeeseeeeeeeeee 22 Maximum Load Warning ZU Jn n 7 REL MAXIMUM LOAD 90 Ib 40 8 kg MAXIMUM LOAD 15 Ib 6 8 kg MAXIMUM LOAD 15 Ib 6 8 kg CAUTION This unit is intended for use only with the products and maximum weights indicated Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury m NOTE Flat Panel TVs with base support should be placed squarely in the center of the stand with no overhang on any side Safety Information Please read and understand this entire manual before attempting to assemble operate or install the product If you have any question regarding the product please call customer service at service at 1 800 986 3460 8 a m 7 p m EST Monday Friday 9 a m 6 p m EST Saturday WARNING This appliance is hot when in use To avoid burns do not touch hot surfaces with bare skin If provided A use handles when moving this appliance Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 ft 0 9 m from the front of this appliance When using electrical appliances basic precautions should WARNING This heater may i
3. OM 1001369825 88966Y 23TF10316 Z513 XXX XXX 88966 23TF10316 Z513 DECORATORS XXX XXX 89420 2323TF10316 Z453 COLLECT Lown USE AND CARE GUIDE ROSENGRANT MEDIA UNIT Questions problems missing parts Before returning to the store call Home Decorators Collection Customer Service 8 a m 7 p m EST Monday Friday 9 a m 6 p m EST Saturday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS THANK YOU We appreciate the trust and confidence you have placed in Home Decorators through the purchase of this electric fireplace We strive to continually create quality products designed to enhance your home Visit us online to see our full line of products available for your home imporvement needs Thank you for choosing Home Decorators Table of Contents Maximum Load Warning Safety Information eere Warranty E Pre Assemibly iei ierat enean anaia ananasen Hardware Included enano nn nnn e Product Specifications TOIS ROQUINCO uicit reote roche Package Contents rte ncas 7 Assembly 2 2enae natione cuna an nna ann annia tne na cna Dua Raua 8 OperatiOn inen err nete nx Rak Rn iiie 17 FCC IC Information essen 19 Care amp Cleaning
4. and Left Base A together secure the Magnetic Catch NN 3 Using the Phillips Screwdriver insert the Long Screws GG from underneath the Left Base A Turn clockwise to tighten Repeat steps to attach the Right Side Panel M to the Right Base C 1 1 Attaching the top assembly Screw Small Bolts AA through previously attached 2 Hole Plastic Connectors Il to the Top Assembly G HOMEDEPOT COM HOMEDECORATORS 11 Please contact 1 800 986 3460 for further assistance Assembly continued 1 2 Attaching back panels 1 3 Attaching the hinge Stand the assembled unit upright Set the Left Door P on a flat surface With the Phillips Screwdriver insert the Screws DD into Using the Phillips Screwdriver insert the Flathead the pre drilled holes to attach the Back Panels 0 Screws EE through the Door Hinges FF to the Left Door P Repeat steps for the Right Door Q 1 4 Attaching the knobs T o Attach the Knob BB to the Left Door P by inserting the screws attached to the Knob BB through the pre drilled holes Use the Phillips Screwdriver to tighten the screws Repeat for the Right Door Q Assembly continued 1 5 Attaching the doors c Align the Left Door P wit
5. inlets and outlets are not blocked as this may cause overheating Unplug the heater for 30 Manual Reset overheat minutes and allow it to cool down Replug protection has triggered and operate Monitor the heater for signs of overheating If the problem persist discon tinue use of the heater and contact customer service Check your heater cord and plug connections Faulty wall outlet connections or loose plugs can cause the outlet or plug to overheat Be sure the plug fits tight in the outlet Heaters draw more current than small appliances Overheating of the outlet may occur even if it has not occurred with the use of other appliances During use check frequently to determine if your plug outlet or faceplate is HOT If so discontinue use of the heater and have a qualified electrician check and or replace the faulty outlet s Normal operation will continue to run for several minutes before shutting down Times will vary based on tempertures During this time cool air will blow Check that the unit is plugged into a standard 120V outlet Press the Power button several times and make sure power is set to the ON position Display shows 3 Display shows E This is normal operation Heater does not blow warm air The heater is in a cool down cycle There is no power and the logs do not glow There is no power to the unit The logs glow but no flame effect The flame effect turned off Press the Flame button se
6. use only identical replacement parts when servicing double insulated tools NOTE SAVE THESE INSTRUCTIONS Warranty 1 Year Limited Warranty The manufacturer warrants that your new Electric Fireplace is free from manufacturing and material defects for a period of one year from date of puchase subject to the following conditions and limitations 1 10 Install and operate this appliance in accordance with the installation and operating instructions furnished with the product at all times Any unauthorized repair alteration willful abuse accident or misuse of the product shall nullify this warranty This warranty is non transferable and is made to the original owner provided that the purchase was made through an authorized supplier of the product The warranty is limited to the repair or replacement of part s found to be defective in material or workmanship provided that such part s have been subjected to normal conditions of use and service after said defect is confirmed by the manufacturer s inspection The manufacturer may at its discretion fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part s Any installation labor construction transportation or other related costs expenses arising from defective part s repair replacement or otherwise of same will not be covered by this warranty nor shall the manufacturer assume responsibility for
7. O m Soome 1 NA Peg flong screw PHSRKNS HH Metal Plate Pre attached PHPLBIKO 1 W Plastic Connector 2 Hole Block PH PCBBKO1 KW Www PMNUD un Bt PBITBKO MM FetWsher CNA NW Mamtotuh PRMCHWWO P00 Leveter Pre attache Praon PP DrawerSlide o CNA QQ Tipping Restraint Hardware PH BKTWTO3 i NOTE Hardware not shown to actual size PRODUCT SPECIFICATIONS VOLTAGE 120VAC 60 Hz AMPS 12 5 Amps WATTS sows o PLANNING ASSEMBLY Before beginning assembly of product make sure all parts are present Compare parts with Hardware Included and Package Contents lists If any part is missing or damaged do not attempt to assemble install or operate the product Contact customer service for replacement parts Estimated Assembly Time 60 Minutes TOOLS REQUIRED ee O Phillips Screwdriver Pre Assembly continued PACKAGE CONTENTS NOTE All panels are labeled left and right as viewed from the front of unit Description Left Base Bottom Front Base Right Base Back Base Panel Center Left Side Panel Center Right Side Panel Top Assembly Decorative Front Left Panel Decorative Front Right Panel Left Drawer Front Panel Left Side Panel Right Side Panel Right Drawer Back Panel Left Door D Q
8. for the environment and human health Recycling used materials also conserves natural resources For more information about collecting and recycling used batteries please contact your local municipality your waste disposal service or the point of sale where you purchased this product o9 FCC IC Information WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and m used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an o
9. front panel Screw Small Bolt AA through the 2 Hole Plastic Connector Il to the Front Panel K HOMEDEPOT COM HOMEDECORATORS 9 Please contact 1 800 986 3460 for further assistance Assembly continued 6 Attaching the panels F Securing the front panel Screw Small Bolts AA through the 2 Hole Plastic To secure the Front Panel K loosen pre attached Metal Connectors Il to connect the Center Left Side Panel E Plate HH and turn clockwise to the Left Base A Using the Phillips Screwdriver insert the Screw DD Repeat to connect the Center Right Side Panel F to the Turn clockwise to tigthen Right Base C Repeat step on other side Insert Wood Dowels KK into pre drilled holes in the Front Panel K Push panels firmly together 8 Preparing outside panels Screw the Small Bolts AA through the 2 Hole Plastic Connectors Il to the Left Side Panel L Repeat for the Right Side Panel M Assembly continued 9 Attaching outside panels 1 0 Preparing the top assembly Lay the assembled base down on flat surface Lay the Top Assembly G down on a flat surface Insert Wood Dowels KK into pre drilled holes in the Left On the bottom side attach the Magnetic Catch NN Side Panel L o Using the Phillips Screwdriver insert the Screws EE to Push the Left Side Panel L
10. Center Right Side Panel F and the Insert Securing Block S 21 Adjusting the level To balance your assembled media unit turn the Levelers 00 as needed The pre attached Levelers 00 are located under the base of the media unit HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued 22 Installing the tipping restraint hardware When the Tipping Restraint Hardware QQ is properly installed it can provide protection against unexpected tipping of the Unit due to small tremors bumps or climbing Your Unit comes with two Tipping Restraint Hardware QQ Each Tipping Restraint Hardware QQ includes one Unit Anchor one Wall Anchor one Anchor Tether and four Anchor Screws Use these to complete the following steps for a proper installation Locate a secure wall stud behind the unit closest to left side Align the Unit Anchor with a wall stud and attach with two Anchor Screws using a Philips Head Screwdriver The Anchor Screws must pass through the Top Assembly G for proper installation Align the Wall Anchor in the center of the wall stud at level with the Unit Anchor and attach with two Anchor Screws using a Philips Head Screwdriver On the Anchor Tether detach the cable from the connector and loop the loos
11. des If repairing or replacing any electrical component or wiring the original wire routing color coding and securing locations must be followed During any service of this appliance the power to the unit must be turned off First turn the main power switch to the OFF position Then remove the electrical plug from the wall outlet WARNING Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire electrical shock and injury to persons WARNING Do not use this fireplace if any part of it has been under water Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electrical shock or personal injury HOMEDEPOT COM HOMEDECORATORS 19 Please contact 1 800 986 3460 for further assistance Troubleshooting PROBLEM ROOT CAUSE CORRECTIVE ACTION Unplug the fireplace remove the back panel of the fireplace and check that the thermo nE n The thermostat sensor is stat is plugged into the main circuit board Display shows broken or disconnected If this does not solve the problem contact customer service for a replacement thermo stat sensor ur 2u Contact customer service for a replacement Display shows E 2 The thermostat sensor is broken thermostat sensor Inspect the heater and check that the air
12. e cable through the eyelets on the Wall Anchor and Unit Anchor Reattach the loose cable to the connector but do not tighten Locate a secure wall stud behind the unit closest to the right side and repeat the steps above Tighten both Anchor Tethers by pulling the cable the through connector NOTE Installation of the Tipping Restraint Hardware QQ will provide a small space between the wall and the m unit This will allow you to run power cords and connector cables to your television or other devices placed on top of the Unit Hardware will help prevent accidents or damage to the WARNING Installing the Tipping Restraint N unit Operation NOTE The control panel can be accessed at the upper right corner of the insert m When a function is changed from the control panel or remote control there will be a corresponding indicator see Figure 1 on the upper right of the projection screen The indicator shows the function changed and the level selected by the control panel or remote control When the function is turned off the corresponding indicator will flash several times and then fade off Powering the fireplace 2 Adjusting the flame Push the Power button to supply power to all functions of the fireplace and put the ins
13. ert in a standby mode Push the Power button again to turn off all functions There are 6 brightness levels that can be selected Settings F6 F4 decrease in Amber brightness Settings F3 F1 decrease in Spectrafire brightness NOTE All previous settings are held in memory so the next time you power up the fireplace the unit will turn on with the same settings m NOTE Holding the Power button on the control panel for 3 seconds will disable the heater function 3 Adjusting the heater Press the Heater button to set the thermostat The fireplace contains three infrared quartz heating elements The thermostat setting range is 62 F 82 F or 17 C 27 C or always ON The thermostat is adjustable by 2 F or 1 C increments The up and down buttons on the remote will increase decrase temperature setting 4 Setting the timer Pressing the Timer button will cycle through the timer settings 30 minutes 1 Hour 2H 3H 4H 5H 6H 7H 8H 9H and off A NOTE To change between F and C press and hold the HEATER button on the control panel for 3 seconds HOMEDEPOT COM HOMEDECORATORS 17 Please contact 1 800 986 3460 for further assistance Operation continued 5 Replacing the remote control battery When the remote control stops operating or its range seems reduced it is time to replace the battery with new ones On the back end of the
14. h the Left Side Panel L Using the Phillips Screwdriver insert the Flathead Screws EE through the Hinges FF to the Left Side Panel L Repeat for the Right Door Q FF EE o 1 6 Inserting wine shelves Insert the Shelf Pins CC into the pre drilled holes Place the Wine Shelves R in and let rest on the Shelf Pins CC 1 T Preparing the insert securing block Set the Securing Block S on a flat surface Connector Il to the Securing Block S Screw the Small Bolt AA through the 2 Hole Plastic nr HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Assembly continued 1 8 Installing the fireplace insert into the mantel assembly Lift the Fireplace Insert T carefully into the back of the unit and center in the fireplace insert opening 1 9 Attaching the insert securing block Screw the Small Bolt AA through the 2 Hole Plastic Connector Il previously attached to the Insert Securing Block S to the Center Right Side Panel F Assembly continued 20 Attaching the insert securing block Insert the 2 Hole Plastic Connector Il into the pre drilled hole in the Center Left Side Panel E Screw the Small Bolt AA through the 2 Hole Plastic Connector Il to the
15. iBbad 1 4 mms 3 5 HeaterBlowerAssemby 1 6 ummPmeOmiBed 1 007 Control Panel Buttons Fd 8 Emberbed with Log 9 Emberbed Circuit Board o oermens O fee 00 e remes e pee 77000 D amp 4 i l N J B 5n a A 3 2 4 T i E 2 7 6 al iW hin ANI ins m th u il TN i TS is Al S Y 1 S VC d ig s l n m i i lt amp E lt V B 1 1 12 amp i 10 A a i 22 HOME DECORATORS COLLECTION Questions problems missing parts Before returning to the store call Home Decorators Customer Service 8 a m 7 p m EST Monday Friday 9 a m 6 p m EST Saturday 1 800 986 3460 HOMEDEPOT COM HOMEDECORATORS RETAIN THIS MANUAL FOR FUTURE USE
16. nclude a visual alarm to warn always be followed to reduce the risk of fire electrical shock that parts of the heater are getting excessively hot If the and injury to persons including the following alarm flashes immediately turn the heater off and inspect for any objects on or adjacent to the heater that may cause high z j 3 temperatures 1 Read all instructions before using this appliance DO NOT OPERATE THE HEATER WITH THE ALARM FLASHING 2 If possible always unplug this appliance when not in use 3 Only a qualified service person should repair this product WARNING This appliance is not a toy Supervise childre 4 Donotuse outdoors playing nea 5 Do not cover the cord under the carpeting Do not cover j with throw rugs runners or the like Arrange the cord away WARNING Use extreme caution when operating heater from traffic areas and where it will not be tripped over near children and the disabled 6 To disconnect this appliance turn the controls to the off position and then remove the plug from the outlet 7 Connect to properly grounded outlets only 8 This appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the current CSA C22 1 Canadian Electrical Code For U S A installations follow local codes and the National Electrical Code ANSI NFPA NO 70 WARNING To prevent a possible fire do not block air intakes 9 This appliance has hot and arcing
17. or sparking parts inside or exhaust in any manner Do not use on soft surfaces like a bed Do not use it in areas where gasoline paint or flammable wie die ranno Cs liquids are used or stored This fireplace should not be used as a drying rack for clothing Do not hang Christmas WARNING Use this appliance only as described in the manual stockings or other decorations on or near this product Any other use not recommended by the manufacturer may cause 10 There is a thermostat limiter inside the heater When inner Mre electe SOCK OF Lotus temperature overheating or abnormal heating occurs the thermostat protective device will cut off the power supply WARNING This appliance has hot and arcing or sparking parts to avoid damage to the fireplace or risk of fire inside Do not use it in areas where gasoline paint or flammable liquids are used or stored This fireplace should not be used as a drying rack for clothing Do not hang Christmas stockings or other decorations on or near this product WARNING This heater is not intended for use in bathrooms A laundry areas and similar indoor locations Never locate this appliance where it may fall into a bathtub or other water container WARNING Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the appliance DANGER High temperatures may be generated under certain abnormal conditions Do not partially or fully co
18. remote press and slide the battery door open and remove the old battery Insert 2 AAA batteries checking that the and sides of the battery match inside the battery compartment Replace the battery compartment door NOTE Do not mix old and new batteries Do not mix alkaline standard carbonzinc or rechargeable nicad nimh etc batteries Do not ingest batteries NOTE Please operate the remote control at a slow buttons in rapid succession may cause the transmitter to malfunction NOTE Batteries should be removed if the product is to be left unused for a long time measured pace Press the remote control buttons with an even motion and gentle pressure Repeatedly pressing Power cord information 3 This heater is for use on 120 volts The cord has a plug as shown in the figure Connect to properly grounded outlets only Do not use a 2 prong adapter Never use with an extension cord or relocatable power tap outlet power strip 6 Disposing of used batteries The battery may contain hazardous substances that could endanger the enviroment and human health This symbol marked on the battery and or packaging indicates that used battery shall not be treated as municipal waste Instead it shall be left at the appropriate collection point for recycling By correctly disposing used batteries you prevent potential negative consequences
19. same The owner user assumes all other risks if any including the risk of any direct indirect or consequential loss or damage arising out of the use or inability to use the product except as provided by law All other warranties expressed or implied with respect to the product its components and accessories or any obligations liabilities on the part of the manufacturer are hereby expressly excluded The manufacturer neither assumes nor authorizes any third party to assume on its behalf any other liabilities with respect to the sale of the product The warranties as outlined within this document do not apply to non accessories used in conjunction with the installation of this product This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty is void if a The fireplace is subjected to prolonged periods of dampness or condensation b Any unauthorized alteration willful abuse accident or misuse of the product C You do not have the original receipt of purchase HOMEDEPOT COM HOMEDECORATORS 5 Please contact 1 800 986 3460 for further assistance Pre Assembly HARDWARE INCLUDED Q tii 6 ds E 2 riens MM ee S Ss AA BB cc DD EE FF GG HH l us Wf wow 7 amp 4 To JJ KK LL MM NN 00 PP QQ ZZ Part Description Aa SmallBolt Knob with Screw Shelf Pi DD Screw EE FatheadScrew 0 OA
20. utlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 Care and Cleaning Dust your fireplace regularly with a soft non lint producing cloth or household dusting product Clean your fireplace with a gentle non abrasive household cleaner Dry your fireplace immediately with a soft cloth or towel Tips for using touch up pen ZZ For scratches stroke in direction of scratch For worn areas stroke in direction of wood grain Rub excess colorant promptly with a soft cloth The motors used on the fan and the flame generator assembly are pre lubricated for extended bearing life and require no further lubrication However we recommend periodic cleaning vacuuming of the fan heater Make sure the unit is turned OFF and unplugged whenever you are cleaning the heater or fireplace AN AN WARNING Make sure the power is turned off before proceeding with repairs Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local co
21. ver or obstruct the front of this heater CAUTION Never leave the heater operating unattended Extreme caution is necessary if unsupervised children or invalids b WARNING In order to avoid overheating do not cover the are nearby heater WARNING If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard A CAUTION Before assembly carefully use scissors or a utility A knife to cut and unwrap all parts Make sure you do not discard AR JR the hardware WARNING Under no circumstances should this fireplace be modified Parts that must be removed for servicing must be re placed prior to operating this fireplace again HOMEDEPOT COM HOMEDECORATORS 3 Please contact 1 800 986 3460 for further assistance Safety Information continued NOTE Use care in assembling your new fireplace Take your time and use the hardware provided and a quality Phillips head screwdriver Never overtighten bolts Do not sit on any part of the mantel NOTE To avoid injury from unexpected starting or electrical shock do not plug the power cord into a source of power during unpacking and assembly The cord must remain unplugged whenever you are adjusting assembling the fireplace If any part is missing or damaged do not attempt to use or plug in the power cord until the missing or damaged part is correctly replaced To avoid electric shock
22. veral times Thermostat setting is Adjust the temperature settings to ensure The heater does not blow warm air preventing the heater from that the thermostat is set higher than the turning on current room temperature 20 Troubleshooting continued PROBLEM ROOT CAUSE CORRECTIVE ACTION Flame effect works but heater func tion does not and the emberbed flashes when the Heater button is pressed The heater is disabled There are no batteries The signal is poor The remote control is not working The remote is too far from the heater With the power on press and hold the POWER button on the control panel for 10 seconds Once re enabled the emberbed lights will flash multiple times Change the remote batteries Operate remote transmitter at a slow meas ured pace Press the remote control buttons with an even motion and gentle pressure Repeat edly pressing buttons in rapid succession may cause the transmitter to malfunction Operate the remote at a distance less than 20 ft from the front of the appliance point the remote at the control panel 21 HOMEDEPOT COM HOMEDECORATORS Please contact 1 800 986 3460 for further assistance Replacement Parts For replacement parts call our customer service department at 1 800 986 3460 8 a m 7 p m EST Monday Friday 9 a m 6 p m EST Saturday Pat Desorption e 1 Flame GeneratorDrve Motor 2 memsuseor OOOO 3 3 Wwmom
Download Pdf Manuals
Related Search