LightShow 87456 Instructions / Assembly
Contents
1. other Lighting Strings or decorative outfits end to end up to a maximum of 216 Watts 1 8 Amps total If connecting to a lighting string that does not have a wattage W rating found on the tag within 6 inches of the plug Calculate The wattage W as follows Multiply the current 0 1A which is on the flag type tag Within 6 inches of the plug by 120 For example string is rated 120V 60Hz 0 1Amps 0 1x120 12 Watts Add the wattage of each light string together for a total of 216 Watts or less Do not exceed 216 Watts Total amount of wattage that can be connected 216W 12W 204 W CAUTION To reduce the risk of fire or electric shock do not attempt to modify string FOR INDOOR AND OUTDOOR USE THESE INSTRUCTIONS ARE FOR THESE ITEM NUMBERS pg 3 85719 85720 85724 85725 87456 88065 88070 88720 89075 89121 89282 89284 87412 87413 87272 87975 82054 82059 88067 87950 87951 88073 87251 87261 88068 87268 87280 88072 35050 89150 89155 89162 89165 89167 89170 89171 89182 89488 89490 89491 35358 89749 89750 89751 35359 85284 89841 89842 35362 89752 89753 89754 89846 89847 89848 18712 18713 18714 35364 89843 89844 89845 18708 18709 18711 35365 35366 34796 34797 34799 47335 80599 83560 35152 35153 35154 88056 88529 88531 88554 37229 37679 37349 37351 37184 37182 37193 37195 36237 37694 NOTE This item is not a toy and should be used for decorative purposes only WARNING This device complies with Part 15 of the FCC Rules Operation i2. LED LIGHTSHOW INSTRUCTION Congratulations You are now the proud owner of a LED LIGHTSHOW Please read the directions carefully before use SAFETY WARNING Remove all plastic fasteners and tags These are part of the packaging and should be discarded SAVE TH ESE INSTRUCTIONS This manual contains important safety and operating instructions for power units WARNING ELECTRIC PRODUCT Keep away from children Not recommended for children under 3 years of age As with all electrical products precautions should be observed during handling and use to reduce the risk of electric shock If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard WARNING Strobe lights have been known to trigger seizures in people with photosensitive epilepsy IMPORTANT SAFETY INSTRUCTIONS WHEN USING ELECTRICAL PRODUCTS BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1 Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use When products are used in outdoor applications connect the product to a Ground Fault Circuit Interrupting GFCI outlet If one is not provided contact a qualified electrician for proper installation This seasonal use product is not intended for permanent installation or use Do not mount or place near gas or electric heaters fireplace cand
3. les or other similar sources of heat Do not secure the wiring of the product with staples or nails or place on sharp hooks or nails Do not let lamps rest on the supply cord or on any wire This product is equipped with push in type lamps Do not twist lamps Always unplug this product before installing or replacing lamps Unplug the product when leaving the house when retiring for the night or if left unattended This is an electric productnot a toy To avoid risk of fire burns personal injury and electric shock it should not be played with or placed where small children can reach it 10 Do not use this product for other than its intended use 11 Do not hang ornaments or other objects from cord wire or light string 12 Do not close doors or windows on the product or extension cords as this may damage the wire insulation 13 Do not cover the product with cloth paper or any material not part of the product when in use 14 This product employs overload protection fuse A blown fuse indicates an overload or shortcircuit situation If the fuse blows unplug the product from the outlet Also unplug any additional strings or products that may be attached to the product Replace the fuse as per the user servicing instructions follow product marking for proper fuse rating and check the product If the replacement fuse blows a short circuit may be present and the product should be discarded 15 Read and follow all instructions
4. ore information 2015 GEMMY INDUSTRIES CORP COPPELL TX 75019 U S A 1 877 250 9032 MADE IN CHINA PRINTED IN CHINA
5. s subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the distance between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Visit WWW GEMMY COM for m
6. that are on the product or provided with the product CAUTION To reduce the risk of fire and electric shock 1 Do not install on trees having needles leaves or branch coverings of metal or materials which look like metal and 2 Do not mount or support wires in a manner that can cut or damage wire insulation SAVE THESE INSTRUCTIONS OO ON O amp O KR WN USE AND CARE INSTRUCTIONS 1 When the product is placed on a live tree the tree should be well maintained and fresh Do not place on live trees in which the needles are brown or break off easily Keep the tree holder filled with water 2 If the product is placed on a tree the tree should be well secured and stable 3 Before using or reusing inspect product carefully Discard any products that have cut damaged or frayed wire insulation or cords cracks in the lampholders or enclosures loose connections or exposed copper wire 4 When storing the product carefully remove the product from wherever it is placed including trees branches or bushes to avoid any undue strain or stress on the product conductors connections and wires 5 When not in use store neatly in a cool dry location protected from sunlight USER SERVICING INSTRUCTIONS To replace the fuse Grasp plug and remove from the receptacle or other outlet device Do not unplug by pulling on cord Open fuse cover Slide open fuse access cover on top of attachment plug towards blades Remove fuse carefully T
7. urn fuseholder over to remove fuse RISK OF FIRE Replace fuse only with 3 Amp 125Volt fuse provided with product Close fuse cover Slide closed the fuse access cover on top of attachment plug RISK OF FIRE Do not replace attachment plug Contains a safety device fuse that should not be removed Discard product if the attachment plug is damaged OOaRKRWN Replace the lamp Step 1 Grasp plug and remove from the receptacle or other outlet device Do not unplug by pulling on cord Step 2 Turn the reflector counter clockwise out of the lampholder Pull lamp and plastic base out SEE FIG 1 Step 3 Replace lamp with 3 6Volt 0 072 Watt flashing lamps provided with product Step 4 Push new lamp base assembly into lampholder Please note the direction of the lampholder and lampbase Push the lamp base in lampholder with the true direction Screw clockwise the reflector back into the lampholder SEE FIG 2 If the new lamp base does not fit in lampholder follow the steps below before step 3 a Remove the base of burnt out lamp by straightening lamp leads and gently pull lamp out b Thread leads of new lamp through holes in old base with one lead in each hole c After lamp is fully inserted into base bend each lead up like other lamps in the light set so that the leads will touch the contacts inside the lampholder LAMP LAMPBASE i FIG 1 FIG 2 CAUTION This string is rated 12 Watts 0 1Amps do not overload Connect
Download Pdf Manuals
Related Search