Home Decorators Collection 1060900910 Instructions / Assembly
Contents
1. D UNIT AT THE DISIRED POSITION MARK THE INSERTION POINTS FOR THE PLASTIC ANCHOR 3 e USING THE PROPER HARDWARE FOR YOUR WALL TYPE AND DRILL 1 4 HOLE INSERT THE PLASTIC ANCHOR 3 INTO THE WALL e TIGHTEN THE RECTANGLE METAL PLATE 1 TO THE PLASTIC ANCHOR 3 BY USING 1 1 2 L FLAT HEAD SCREW 5 12 13 e USING THE PLASTIC BAND 4 CONNECT TWO RECTANGLE METAL PLATES 1 13 132. ENING THOROUGHLY CLEAN ALL WOOD SURFACES TO REMOVE DUST AND DIRT THAT MAY HAVE SETTLED ONTO THE FINISH DURING SHIPMENT IN ORDER TO PREVENT DAMAGE DURING ASSEMBLY PLEASE ASSEMBLE THIS ITEM WITH AT LEAST TWO PEOPLE NOTE TURN THE CAM BOLT SCREWS UNTIL THEY ARE TIGHT THE SHOULDER SHOULD BE AGAINST THE SURFACE OF THE PART NOTE e THE ARROWS ON THE HIDDEN CAM LOCKS SHOULD POINT TO THE CAM BOLTS WARNING Serious or fatal crushing injuries can occur from furniture tip over To help prevent tip over Place heaviest items in the lowest drawers Unless specifically designed to accommodate do not set TVs or other heavy objects on top of this product Never allow children to climb or hang on drawers doors or shelves Never open more than one drawer ata time OR Do not defeat or remove the drawer interlock system Use of tip over restraints may only reduce but not eliminate the risk of tip over This is a permanent label Do not attempt to remove 5 13 S LLI z L D en LLI I LL L m LLI 2 LLI 9 e 6 13 e INSTALL THE WOOD DOWEL a AND THE CAM LOCK BOLT b INTO LEFT SIDE PANEL A AND RIGHT SIDE PANEL B e JOIN THE LEFT SIDE PANEL A AND RIGHT SIDE PANEL B TO THE FRONT CROSS BAR G AND THE BACK CROSS BAR F BY USING THE WOOD DOWEL a FIRST e ONCE JOINED TIGHTEN CAM LOCK c ONTO BOLT b USING PRE DRI
3. HOME DECORATORS COLLECTION SK17192 SHUTTER 2 DRAWER FILE CABINET 30 5 Hx20 9 Wx18 D INV 10609 ASSEMBLY INSTRUCTIONS Made In China 1 13 Thank you for purchasing this quality product Be sure to check all packing material carefully for small parts which may have came loose inside the carton during shipment Count all parts and material hardware then compare with parts list to be sure all parts are present If any parts are missing or damaged phone fax or mail to our Customer Service Department for efficient and speedy service Please indicate the model number and code letter of part s needed IMPORTANT NOTE Follow instructions listed below in proper sequence as numbered to assure fast easy and correct assembly DRAWER DRAWER 2 13 BALL FOOT 4PCS ROUND HEAD SCREW 22PCS FLAT HEAD SCREW 16PCS KNOB 2PCS KNOB BOLT 2PCS METAL BAR 4PCS METAL PLATE 2PCS RECTANGLE 1 2 L FLAT PLASTIC ANCHOR METAL PLATE HEAD SCREW 1 1 2 L FLAT FLASTIG HEAD SCREW BAND ANTI TIPPING HARDWARE PACKAGE NOTE THE SURFACE WITH THE STICKER IS THE BACK SIDE 3 13 HOW TO SEPARATE GLIDES SAFETY RELEASE TAB PRIOR TO ASSEMBLY WE SUGGEST SEPARATING THE INNER GLIDES FROM THE OUTER GLIDES SIMPLY PULL THE LEFT RIGHT INNER GLIDES FROM THE OUTER GLIDES EXPOSING A SMALL BLACK SAFETY RELEASE TAB BY PUSHING THE SAFETY RELEASE TAB YOU WILL BE ABLE TO SEPARATE THE GLIDES 4 13 NOTE e UPON OP
4. LLED HOLES 7713 e INSTALL THE WOOD DOWEL a AND THE CAM LOCK BOLT b INTO THE TOP PANEL C e JOIN THE TOP PANEL C TO THE ASSEMBLED PART BY USING WOOD DOWEL a FIRST e ONCE JOINED TIGHTEN CAM LOCK c ONTO BOLT b USING PRE DRILLED HOLES 8 13 e INSTALL THE WOOD DOWEL a AND THE CAM LOCK BOLT b INTO THE BOTTOM PANEL D e JOIN THE BOTTOM PANEL D TO THE ASSEMBLED PART BY USING WOOD DOWEL a FIRST e ONCE JOINED TIGHTEN CAM LOCK c ONTO BOLT b USING PRE DRILLED HOLES 9 13 e TIGHTEN THE BACK PANEL E AND METAL PLATE i TO THE ASSEMBLED PART BY USING THE ROUND HEAD SCREW d 10 13 e TIGHTEN THE DRAWER LEFT SIDE PANEL I AND THE DRAWER RIGHT SIDE PANEL DRAWER FRONT PANEL H BY USING THE FLAT HEAD SCREW e e SLIDE THE DRAWER BOTTOM PANEL K TO THE GROOVES ON DRAWER THE DRAWER LEFT SIDE PANEL I AND THE DRAWER RIGHT SIDE PANEL J e TIGHTEN THE DRAWER BACK PANEL L TO THE ASSEMBLED PART BY USING THE FLAT HEAD SCREW e e TIGHTEN THE KNOB f TO THE DRAWER FRONT PANEL BY USING THE KNOB BOLT g e PLACE THE METAL BAR INTO THE DRAWER FRONT PANEL H AND THE DRAWER BACK PANEL L e REPEAT STEPS ABOVE FOR THE 2NP DRAWER 11 13 e SLIDE THE ASSEMBLED DRAWER INTO THE ASSEMBLED UNIT e TIGHTEN THE RECTANGLE METAL PALTE 1 TO THE REAR END OF THE TOP PANEL C BY USING THE 1 2 L FLAT HEAD SCREW 2 e PLACE THE ASSEMBLE
Download Pdf Manuals
Related Search