DreamLine SHBW-1440742-01 Installation Guide
Contents
1. Fig 20 Ver 1 Rev 1 18 Mark the location for the Shelf brackets 04 according to the measurements in Fig 20 and Fig 21 1 Drill the holes using 5 16 drill bit and insert the Wall anchors 06 See Fig 21 for details 19 Mount the Shelf brackets 04 to the wall using the Countersunk screws ST4 2x30 07 NOTE the padded set screw of the Glass bracket should be facing down Slide the upper Glass shelf 05 into the upper Shelf brackets and tighten the set screws at the bottom of the brackets Then slide the bottom Glass shelf in place Tighten the set screws on the bottom Shelf brackets as well See Fig 22 and Fig 23 for details 3 1 2 3 1 2 3 1 2 Fig 21 Ver 1 Rev 1 Fig 23 Product maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface Acrylic cleaning procedure Acrylic should be cleaned with warm water and a clean nonabrasive cloth If desired a mild nonabra2. QREAMLINE ream In style QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page A Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Back Wall please visit www BathAuthority com Ver 1 Rev 1 Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has bee
3. Also apply the sealant around the drilled holes See Fig 14 for details Fig 14 Fig 13 Ver 1 Rev 1 11 12 13 Slide the narrow edge of the Side panel 01 behind the Corner cover 02 Align trimmed edge of the Side panel from Step 4 with the marked line on the wall in Step 2 and push the Side panel against the wall NOTE Make sure the drilled holes on the Side panel are also aligned with the fixtures on the wall See Fig 15 for details Apply sealant to the entire surface of the reverse side of the other Side panel 01 See Fig 14 for details Slide the narrow edge of the Side panel 01 behind the Corner cover 02 Align trimmed edge of the Side panel from Step 4 with the marked line on the wall in Step 2 and push the Side panel against the wall Align the top of both Side panels and the Back panel before the sealant sets Apply equal pressure to the whole surface of the Acrylic panels from top to bottom See Fig 16 for details Fig 15 Fig 16 Ver 1 Rev 1 11 14 Once Side panels 01 aligned fasten tight the Corner cover 02 to secure the Si
4. 3 Determine the position of both Side panels 01 NOTE a The narrow edge of the Side panels fits behind the corner cover and cannot be trimmed b The wide edge of the Side panel can be trimmed to the size of your measurements from step 2 Measure from the narrow edge of the Side panel and place a mark at a distance of D1 and D2 that you measured in Step 2 Draw a straight line from top to bottom along the wide edge of the Side panel See Fig 4 for details Line to cut D1 D1 D2 Fig 3 D2 Fig 4 Line to cut Ver 1 Rev 1 4 Place the Side panel 01 on a flat piece of plywood or particle board Use a sharp industrial knife and a T square to score along the marked wide ends of the Side panel and continue scoring until you have fully cut through the panel See Fig 5 and Fig 6 for details IN K S At Lit D WL ANN LUOANNNY s Xe A NW Sy 1 es Ut A N WY y X S V D1 Fig 6 Ver 1 Rev 1 n D2 5 Take exact measurements of 1 A the fixture on the wall e from the 1 one inch line in the corner of the shower i to the fixture A B C e from the bottom of the wall of the shower to
5. the fixture E F See Fig 7 for details a C E _ B Fig 7 6 Determine which Side panel 01 will be installed on N the side wall with the fixture A D2 Mark the fixture location on the Side panel according to the measurements taken in Step 5 A See Fig 8 for details E A F i 1 7 B aA C Fig 8 Ver 1 Rev 1 7 Drill the holes for the fixtures in the Side panel 01 using the proper diameter saw bit or a handheld jig saw See Fig 9 for details Acrylic Side Panel Installation Instruction 8 Attach the Corner cover 02 to 1 the corner of the shower and mark the drilling holes through the predrilled holes in the Corner cover AT Move aside the Corner cover Drill the holes using 5 16 drill bit and insert the Wall Anchors 06 See Fig 10 and Fig 11 for details 5 16 D2 Fig 9 2 Fig 10 Ver 1 Rev 1 Fig 11 9 Mount the Corner cover 02 to the corner of the 1 shower using the Countersunk screws ST4 2x30 07 Do not fully tighten the screws at this time leave them loose for further installation See Fig 12 and Fig 13 for details Fig 12 Ver 1 Rev 1 10 Apply the sealant to the entire surface of the reverse side of the Side panel 01
6. de panels Cover the screw holes with the Decorative cover 08 See Fig 17 for details ATTENTION Prior to the next step please be sure the part of the wall for installation of the Decorative edge molding 03 is clean dry and free from soap oil and any construction debris 15 Gently remove the plastic tape from the adhesive side of the Decorative edge molding 03 and firmly press it to the edge of the Side panel 02 from top to bottom See Fig 18 for details Fig 17 1 Side Panel A Wall A Decorative Molding Side Panel 2 a Wall A A Decorative Molding A Fig 18 Ver 1 Rev 1 16 Apply caulk along the top edge of the Side panels 01 and along the connection of b the bottom edges of the Side panels with the Shower base See Fig 19 for details ATTENTION Installation of QWALL 4 Acrylic shower wall is complete If you want to install Glass shelves 05 to your Shower follow to the next step Fig 19 Glass Shelves Installation Instruction 17 Determine the desired height for the Glass shelves 05 and mark the locations on the wall NOTE LOAN The Glass shelves can be installed either i two in one corner or one in each See Fig 20 for details
7. n installed Feel free to contact DreamLine if you have any questions 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project 3 This acrylic wall system is specially designed to be installed over any solid surface If you are installing the acrylic walls over the existing tiles remove all loose tiles before the installation If you are installing over the existing painted walls take all loose paint off Please note that some cutting and drilling might be necessary during the installation process 4 Make sure to turn off the water supply remove faucet handles or any fixture trims protruding from the wall Clean the surface removing soap film and dirt from all wall surfaces using regular household detergent and then wipe it dry Tools Required Tape l Drill bit T Sd are Caulk Measure Pencil Knife 5 16 q i i Caulk l Phillips Level Gun a raii Hammer Screwdriver Ver 1 Rev 1 2 Detailed Diagram of Acrylic Shower Wall Components 2 P4 1 3 4 f J 9 I 6 7 A 8 Packing List 01 Side panel 2pcs 05 Glass shelf 2pcs 02 Corner cover 1pc 06 Wall anchor 11pcs 03 Decorative edge molding 2pc
8. s 07 Countersunk screw ST4 2 x30 11pcs 04 Shelf bracket 6pcs 08 Decorative cover 5pcs NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using the detailed diagram and packing list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement NOTE Retain these installation instructions for future reference Ver 1 Rev 1 3 Preparation for Installation of Side Panel ATTENTION Side Panel If you are installing a shower enclosure with a wall Wall Profile x profile you can hide the edge of the Side panel 01 behind the wall profile Wall 4 N See Fig 1 for details A a Side Panel a Wall Profile 4 Wall 4 Fig 1 1 Place a mark on the walls with a distance of 1 one inch from the corner and draw a plumb vertical line from top to bottom 1 See Fig 2 for details ail 2 sq ye i i _ Fig 2 Ver 1 Rev 1 2 Measure the walls of the shower from the 1 one inch line in the corner from Step 1 to the points where you want Side panels 01 to end The distances are D1 and D2 NOTE D2 Shows wall with the fixture See Fig 3 for details
9. sive detergent may also be used Use only light pressure when cleaning Avoid rubbing dirt or grit into the surface Turn the cloth often and replace with a clean cloth frequently Dry by blotting gently with a clean dry cloth DO NOT USE Window cleaning sprays alcohol kitchen abrasive compounds or solvents such as acetone gasoline or thinners Do not use ammonia based cleaning solutions on the acrylic as it will eat into the surface and cause it to damage How do you get scratches out of Acrylic For light scratches use a buffing compound such as a car wax Use a buffer or slightly buff the surface by hand until scratches disappear Ver 1 Rev 1 15 EAMLINE dream in style TEL 866 731 8378 215 957 1411 FAX 866 227 9245 215 893 1780 WWW BATHAUTHORITY COM For more information on DreamLine Shower Back Wall please visit www BathAuthority com
Download Pdf Manuals
Related Search