KOHLER K-4327-0 Installation Guide
Contents
1. Water gt Air PRY START UP Turn on the water supply to bring the Pressure Lite system to its operating pressure approximately 1 minute Check for leaks Slight retightening of any leaking connections should stop seal leaks If the toilet is leaking between the tank and bowl carefully retighten the three tank bolts evenly Check all bowl and tank connections for leaks for several days Flush and repressurize the toilet three times to stabilize the system Kohler Co Kohler WI U S A 113169 2 EB GAP CLEARANCE If the toilet does not activate the gap between the actuator and plunger arm may need to be reset Make sure the trip lever handle is installed and the trip lever nut is tight This is a left hand thread turn counterclockwise to tighten Make sure the water supply is on and the supply line water has stopped flowing into the toilet Loosen the setscrew Turn the actuator until there is a 1 16 2mm 3 32 2 4mm gap between the actuator and the plunger arm Turn the actuator clockwise to increase the gap Tighten the setscrew after the gap is properly adjusted NOTE Loss of gap clearance adjustment could cause leakage into the toilet bowl due to the plunger not sealing properly This condition could cause a continual flow of water If the problem is not corrected after adjustment refer to the troubleshooting chart on Page 7 Gap Adjustment 1 16 2mm 3 32. flow or plunger arm refer to Page 6 tank fill water will not shut off B Plunger arm is binding B Repair or replace plunger arm refer to installer dealer for assistance C Pressure regulator is not working C Replace the lower supply group Phone 1 800 533 3450 for assistance Kohler Co Kohler WI U S A 7 113169 2 EB IMPORTANT CONSUMER INFORMATION CONSUMER RESPONSIBILITIES If you live in a hard water area you should make certain that the holes in the rim are kept clean for proper bowl flushing Toilet bowl cleaners should be used atleast once a week Use a long handled brush to clean the rim holes and to clean as far into the trap as possible to prevent mineral deposits from forming Cleaning of the Pressure Lite tank system is not necessary If cleaning is desired use mild soap and water Most toilet bowl cleansers are not harmful to the vitreous china surface of the toilet bowl Please follow the bowl cleanser manufacturer s instructions carefully Do not use abrasive cleaners or solvents REQUESTING SERVICE Please take a moment to familiarize yourself with the Kohler Warranty its benefits and limitations Kohler Co and its distributors support you with one of the largest Service Networks of its type Here s what you need to do if you require service FIRST Contact the dealer or contractor who sold and installed the product They should be able to solve any problems you
3. 2 2 4mm Setscrew Actuator e Plunger Arm INSTALL SEAT To install use the seat attachment hardware and instructions packed with the toilet seat MAINTENANCE WINTERIZING Shut off the water supply Flush the toilet Press the actuator down for approximately one minute to drain water from the vessel assembly Disconnect the supply line Remove the supply shank and drain the water from the tank Press the actuator one more time then pull it up to allow air into the vessel Add antifreeze to the toilet bowl water to prevent freezing Use recreational type antifreeze commonly used in campers motor homes and boats For start up connect water supply and refer to the Start Up section on Page 5 NOTE Refer to the Sloan Flushmate Owner s Service Manual included for more information Actuator Vessel Overflow Valve Q KG Pressure Regulator Screen 113169 2 EB Kohler Co Kohler WI U S A TROUBLESHOOTING The troubleshooting guide below is meant for general aid only All fittings in this toilet except for the plunger nut are preset by the manufacturer to prevent adjustment Any attempt to adjust the fittings except the plunger nut and winterizing may damage the toilet Such adjustments for modifications of this product are not normal usage and will void the warranty For proper trip lever adjus
4. KOHLER INSTALLATION INSTRUCTIONS BARRINGTON PRESSURE LITE VITREOUS CHINA SIPHON JET TOILET K 4327 BEFORE YOU BEGIN INSTALLER HAZARD NOTIFICATION WARNING Risk of injury or water damage Contents of vessel under pressure can cause severe injury Do not open or service before reading installation instructions or service instructions Turn off water supply and flush unit to release pressure before attempting any service CAUTION Risk of product damage Do not use any oils or lubricants on the Pressure Lite system CAUTION Risk of product damage The fittings in this toilet require no adjustment except for possible gap clearance adjustment and winterizing refer to Page 6 The fittings in this toilet are preset Any adjustment or modifications of the product are not normal usage and void the warranty WARNING Risk of injury or product damage Handle vitreous china products very carefully Vitreous china can break and chip if you overtighten bolts and nuts NOTICE For service and warranty on the Sloan Flushmate vessel and related components see the Sloan Flushmate Owner s Service Manual included Follow all local plumbing codes PRODUCT PROPERTIES e Pressure Lite System e Water surface to rim is 6 7 8 17 5cm e 2 1 4 5 7cm passageway e For roughing in and overall dimensions see roughing in diagram on Page 2 e Fixture dimensions are nominal and conform to tolerances by ANSI ASME Stand
5. ards A112 19 2 NOTICE Due tothe pressure within the vessel the flush noise level may be higher than that of a gravity flush toilet PRODUCT REQUIREMENTS e The supply stop should be 8 20 3cm above the floor line and 7 17 8cm to the left of the closet flange centerline e Since all toilets do not have the same supply rough in you may have to change the location of the supply stop to install this toilet e Closet flange must be 4 10 2cm on center from floor e Seat post holes are on 5 1 2 14 2cm centers e For most satisfactory operation the toilet requires 20 p s i 1 8Kg cm2 static pressure minimum at the supply stop The pressure is not to exceed 80 p s i 5 5Kg cm2 maximum static pressure ORDERING INFORMATION TOEI 1 03 c0de tive er oere e nuage ds K 3546 When specified 3 8 SUPDIY ace svete minini who oxen dae K 7637 Floor DOS si ssretrnsi ne enews ed ee lew 21401 NOTE For service parts ordering information see the label on the underside of the tank cover NOTICE For service and warranty on the Sloan Flushmate vessel and related components see the Sloan Flushmate Owner s Service Manual included MATERIALS REQUIRED e Supply stop 3 8 recommended e Toilet gasket wax seal e Toilet T bolts 1 2 6mm or 5 16 8mm diameter 2 required e Toilet supply tubing TOOLS REQUIRED e Tape measure e Screwdriver TOOLS REQUIRED e 10 adjustable wrench e Tubing cutte
6. hex nuts so the top of the tank is level with the top of the bowl Pushing down on the top of the tank will make it easier to tighten the brass hex nuts Tighten the brass hex nuts one or two turns past hand tight to obtain a level tank and watertight seal CAUTION Risk of personal injury or product damage Overtightening may cause breakage or chipping of the vitreous china Tank Bolt Gasket CONNECT SUPPLIES Carefully bend the supply stop tubing to fit Measure for required penetration into the supply stop Cut and de burr the tubing Install the connection hardware onto the tubing as shown Hand tighten the coupling nut first and then the compression nut WARNING Risk of property damage Do not overtighten or you may deform the connections and cause a leak Do not use tools to tighten plastic nuts Supply Shank 3 gt Washer Tubing Compression Nut Coupling Nut f Perle P Supply Stop NEES PRESSURE LITE SYSTEM WARNING Risk of personal injury or water damage Contents of the vessel are under pressure and can cause severe injury Do not open or service before reading installation instructions or service instructions Turn off the water supply and flush the unit to release pressure before attempting any service CAUTION Risk of product damage Do not use any oils or lubricants on the Pressure Lite system 113169 2 EB Kohler Co Kohler WI U S A OPERATION The vitreous chi
7. let horn before setting the toilet Install the closet gasket for sealing the toilet to the outlet connection For gasket installation refer to the instructions packed with the gasket NOTE For a floor mounted wall outlet bowl an all wax ring is not recommended If desired apply a bead of toilet setting compound approximately 1 4 6mm thick around the base and back of the toilet Refer to gasket instructions O 7 Kohler Co Kohler WI U S A 113169 2 EB SECURE TOILET Carefully align and set the toilet into position ensuring that all gasket installation instructions are followed Tighten the wall bolts ensuring proper gasket seal Install 1 4 6mm floor mounting bolts Assemble the bolt cap bases washers and nuts Hand tighten the nuts then tighten them an additional 1 2 turn with a wrench CAUTION Risk of personal injury or product damage Overtightening may cause breakage or chipping of the vitreous china If the floor bolts extend more than 1 4 6mm from the top of the nut loosen the nut and turn the bolt further into the floor Retighten the nut and install the bolt caps NS Bolt Cap 9 lt D Washer Bolt Cap Base INSTALL TANK Set the tank on the bowl using the bolts as a guide Center the gasket on the inlet of the bowl Assemble the washers and brass hex nuts onto the bolts and hand tighten evenly Alternately tighten the brass
8. may have SECOND If your dealer or contractor cannot solve the problem they will contact or supply you with the name of the local Kohler Distributor and the KOHLER TECHNICAL SPECIALIST E THIRD If you are unable to obtain warranty service through either your contractor or Kohler Co distributor please write us directly at Kohler Co Attn Customer Service Department 444 Highland Drive Kohler WI 53044 U S A Any problems technical questions or warranty issues involving the Sloan Flushmate vessel or its related components should be directed to Sloan at 1 800 533 3450 FOURTH Include all pertinent information regarding your claim including a complete description of the product model numbers colors finishes and the date the product was installed Include a description of the problem and a photocopy of your invoice for the products involved Also give us the name of the contractor and distributor LIMITED ONE YEAR WARRANTY Kohler plumbing fixtures and fittings are warranted free of manufacturing defects Kohler Co will at its election repair replace or make appropriate adjustment where Kohler Co inspection discloses any such defects occurring in normal usage within one year after installation Kohler Co is not responsible for installation or removal costs To obtain warranty service contact Kohler Co either through your Dealer or Plumbing Contractor or by writing Kohler Co Attn Customer Service De
9. na bowl and tank direct the flushing water flow and house the Pressure Lite system The vessel contains the complete operating cartridge assembly and is the container for the pressurized 1 6 gallons 6 1 L of water used for each flush The control components consist of the pressure regulator and the air inducer These components work with the incoming pressurized supply line water to provide a regulated pressure flush to the toilet bowl A complete flush cycle is two separate functions When the trip lever is operated the vessel plunger assembly is pressed allowing pressurized water to be directed to the bowl for complete flushing action As the water level in the vessel drops the plunger will close stopping water flow to the bowl A checkport built into the vessel assembly allows any discharge of water into the vitreous tank to drain directly into the bowl After flushing a charge cycle takes place Supply line water flows into the vessel through the screen and pressure regulator The water then flows across the air inducer which mixes a small amount of air with the water filling the vessel until a pressure of approximately 35 p s i 2 5Kg cm2 is reached The toilet will be ready for the next flush within 60 to 90 seconds If the toilet is not ready for the next flush within that time please refer to the troubleshooting chart on Page 7 Actuator Vessel Overflow Valve TE Q EN Pressure Regulator Screen
10. ouble Wye trap seal loss the back to back Pressure Lite toilet Fixture Combination and 1 8 must be connected to a vertical stack using one of Fitting Wye and 1 8 Bends the following three fittings Bends e Double fixture fitting e Double combination wye and 1 8 bends e Double wye and 1 8 bends 113169 2 EB 2 Kohler Co Kohler WI U S A ROUGHING IN DIMENSIONS 5 8 1 6cm 31 78 7cm i 20 3 4 52 7cm FRONT OF BOWL R 6 1 2 fi 16 5cm 28 1 4 71 8cm ai 28 2 5 8 6 7cm 71 1cm 1 1 8 2 9cm enemy 15 AS 13 1 2 8 1 4 38 1cm 1 34 3cm aa pe K 4327 a T91 B 10 2cm Zoo 20 30m 6 15 2cm ote BASE 3 8 1 P S SUPPLY INSTALL SUPPLY STOP For supply installation refer to the instructions packed with the supply stop Locate the supply stop so it is 8 20 3cm above the floor line and 7 17 8cm to the left of the closet flange centerline INSTALLATION Secure the outlet connection or flange with mounting bolts to the wall according to the manufacturer s instructions See the roughing in illustration for the dimensions Pre install the toilet and mark the location of the floor bolts Remove the bowl Drill mounting holes for 1 4 6mm floor bolts at the desired locations Do not install the bolts until after final toilet placement Remove any rags or other seal on the out
11. partment 444 Highland Drive Kohler WI 53044 U S A or by calling 1 800 4 KOHLER from within the U S A Implied warranties including that of merchantability or fitness for a particular purpose are expressly limited in duration to the duration of this warranty Kohler Co disclaims any liability for special incidental or consequential damages Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of special incidental or consequential damages so these limitation and exclusion may not apply to you This warranty gives you specific legal rights You may also have rights which vary from state to state This limited warranty provides specific legal rights as they apply within the U S A and other rights may be available but may vary from country to country This is our exclusive written warranty KOHLER CO KOHLER WISCONSIN 53044 113169 2 EB Kohler Co Kohler WI U S A
12. r e Hacksaw e Level e Putty knife e Metal file NOTE Site preparation may require additional tools 113169 2 EB 2001 Kohler Co SITE PREPARATION REMOVE EXISTING TOILET NOTICE Carefully inspect new fixture for any sign of damage before removing existing toilet If any damage to vitreous china or Pressure Lite system components are discovered stop installation and call place of purchase for assistance Inspect the complete toilet to ensure that the e Components are attached securely e Trip lever and plunger arm move freely e Vessel is securely mounted e Vitreous china is undamaged Turn off the water supply Flush the toilet and sponge out all remaining water from the tank and bowl Disconnect the supply stop and remove the old tank and bowl Remove the old gasket from the wall and outlet flange with a putty knife Remove the old T bolts the T shaped bolts in the closet flange and discard CAUTION Risk of hazardous gases If the new toilet is not installed immediately temporarily stuff a rag in the closet flange ROUGH IN PLUMBING Turn off the water supply N VY Install or relocate the supplies and outlets as necessary to conform to the roughing in dimensions CAUTION Risk of trap seal loss in back to back installations To prevent possible Double Double D
13. tment procedures refer to Gap Clearance on Page 6 in these instructions Any problems technical questions or warranty issues involving the vessel or its related components should be directed to 1 800 533 3450 Any other problems not covered in this chart should be referred to your installer dealer SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION No flush A Supply stop is closed A Fully open supply stop Trip lever is loose B Tighten nut turn counterclockwise to tighten C Trip lever does not actuate plunger C Adjust linkage or actuator gap refer to Page 6 D Obstruction within water inlet D Replace inlet components Phone components 1 800 533 3450 for assistance E Screen is clogged E Clean the screen Phone 1 800 533 3450 for assistance Replace the screen if necessary Poor flush A Bowl rim holes are clogged A Clean under bowl rim Trapway or drain line is clogged B Plunge bowl auger trap auger drain to clear blockage C System is not pressure charged C Adjust plunger adjuster for proper actuation arm gap refer to Page 6 D Supply stop is not opened D Fully open supply stop Drain line vent is clogged E Refer to installer dealer for assistance F Screen is clogged F Clean the screen with a medium to hard bristle brush Replace the screen if necessary Phone 1 800 533 3450 for assistance Bowl water A Plunger is not seating properly A Adjust gap between actuator and continues to
Download Pdf Manuals
Related Search